WMI problem - Can not display System Information

[Steve]

System Information does not display any information at
all since uninstalling Roxio Easy CD Creator 5. Easy CD
Creator 6 is installed and working flawlessly. How can I
repair or replace the registry files that appear to be
preventing the necessary programs and/or services from
executing as before to provide this information?

Steve

[Roger Abell [MVP]]

At a cmd prompt when you enter=20
echo %path%=20
does the output contain C:\WINDOWS\system32\WBEM
Normally the path should begin=20
C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\system32 \WBEM;
(assuming install is to C:)
You can correct this in the Properties of My Computer=20
by clicking Environment Variable on Advanced tab.

--=20
Roger=20

"Steve" > wrote in message =
...
> System Information does not display any information at=20
> all since uninstalling Roxio Easy CD Creator 5. Easy CD=20
> Creator 6 is installed and working flawlessly. How can I=20
> repair or replace the registry files that appear to be=20
> preventing the necessary programs and/or services from=20
> executing as before to provide this information?
>=20
> Steve
>

[Steve]

Yes. However the WBEM is Wbem -is that significant?

Also it also contains C:\Program Files\Common Files\Roxio
Shared\DLLShared

....Now what say you of fixing this in System Properties?

Thanks

Steve

[Steve]

Could you provide some assistance as to how I might fix
this problem in Environment Variable in My Computer. I
don't quite see what to fix, if this will truly solve
this issue.

Thanks in advance...

Steve


>-----Original Message-----
>At a cmd prompt when you enter
>echo %path%
>does the output contain C:\WINDOWS\system32\WBEM
>Normally the path should begin
>C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\system32 \WBEM;
>(assuming install is to C:)
>You can correct this in the Properties of My Computer
>by clicking Environment Variable on Advanced tab.
>
>--
>Roger
>
>"Steve" > wrote in message
...
>> System Information does not display any information at
>> all since uninstalling Roxio Easy CD Creator 5. Easy
CD
>> Creator 6 is installed and working flawlessly. How
can I
>> repair or replace the registry files that appear to be
>> preventing the necessary programs and/or services from
>> executing as before to provide this information?
>>
>> Steve
>>
>.
>

[Roger Abell [MVP]]

If C:\WINDOWS\system32\WBEM (or Wbem, etc. with=20
c: adjusted to actual drive) is already in the path then this=20
is not your cause.

Is anything other than System Properties not working for=20
you ? Is anything being written into the event logs when=20
you try this ?

--=20
Roger=20

"Steve" > wrote in message =
...
> Could you provide some assistance as to how I might fix=20
> this problem in Environment Variable in My Computer. I=20
> don't quite see what to fix, if this will truly solve=20
> this issue.
>=20
> Thanks in advance...
>=20
> Steve
>=20
>=20
> >-----Original Message-----
> >At a cmd prompt when you enter=20
> >echo %path%=20
> >does the output contain C:\WINDOWS\system32\WBEM
> >Normally the path should begin=20
> >C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\system32 \WBEM;
> >(assuming install is to C:)
> >You can correct this in the Properties of My Computer=20
> >by clicking Environment Variable on Advanced tab.
> >
> >--=20
> >Roger=20
> >
> >"Steve" > wrote in message=20
> ...
> >> System Information does not display any information at=20
> >> all since uninstalling Roxio Easy CD Creator 5. Easy=20
> CD=20
> >> Creator 6 is installed and working flawlessly. How=20
> can I=20
> >> repair or replace the registry files that appear to be=20
> >> preventing the necessary programs and/or services from=20
> >> executing as before to provide this information?
> >>=20
> >> Steve
> >>=20
> >.
> >

[Steve]

This is the only problem I have noticed, I don't believe
anything else is having a problem.

I am getting an error now Unable to start a DCOM
server "Access Denied" while starting command
C:\WINDOWS\System32\wbem\wmiprvse.exe -Embedding

and now an error The driver detected a controller error
on \Device|Scsi\aic78xx1 but I just started using a Scsi
cdrw that I don't usually use a lot.

Any suggestions? How would I go about having someone
have a look via remote access?

Thanks

Steve




>-----Original Message-----
>If C:\WINDOWS\system32\WBEM (or Wbem, etc. with
>c: adjusted to actual drive) is already in the path then
this
>is not your cause.
>
>Is anything other than System Properties not working for
>you ? Is anything being written into the event logs
when
>you try this ?
>
>--
>Roger
>
>"Steve" > wrote in message
...
>> Could you provide some assistance as to how I might
fix
>> this problem in Environment Variable in My Computer.
I
>> don't quite see what to fix, if this will truly solve
>> this issue.
>>
>> Thanks in advance...
>>
>> Steve
>>
>>
>> >-----Original Message-----
>> >At a cmd prompt when you enter
>> >echo %path%
>> >does the output contain C:\WINDOWS\system32\WBEM
>> >Normally the path should begin
>> >C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\system32
\WBEM;
>> >(assuming install is to C:)
>> >You can correct this in the Properties of My Computer
>> >by clicking Environment Variable on Advanced tab.
>> >
>> >--
>> >Roger
>> >
>> >"Steve" > wrote in message
>> ...
>> >> System Information does not display any information
at
>> >> all since uninstalling Roxio Easy CD Creator 5.
Easy
>> CD
>> >> Creator 6 is installed and working flawlessly. How
>> can I
>> >> repair or replace the registry files that appear to
be
>> >> preventing the necessary programs and/or services
from
>> >> executing as before to provide this information?
>> >>
>> >> Steve
>> >>
>> >.
>> >
>.
>