It's sound more and more like M.I.T settings
in your BIOS. What you need to do is only insert
one memory stick, boot and see if you can immediately enter
the BIOS. Do this by "Powering ON the computer and
pressing Del key several time to immediately will allow
you to enter BIOS setup.
If you can select "Load Optimized Defaults", then Save and Exit the BIOS.
Then power down, turn off the power supply or remove the power cord
wait 30 seconds and insert the second memory stick.Power up and if see if
all is well.
If still having problems power down and remove one stick.
Then power up and from the main BIOS Menu enter the "Check PC Health"
status.
(Page 53 of the motherboard manual)
Next check the "Frequency and Voltage Control"
The "CPU Core voltage" ,
"Memory Frequency (MHz)" and "CPU Host Frequency (MHz)"
Note: Mem Freq number must be equal to or less the Ram Stick ratings.
(Page 55) Same for memory voltages. If you can change the
After you check and adjust any values if necessary go back to the
main BIOS menu and press Ctrl+F1, Gigabyte sometime hides
the advanced setting from users. Let me know if Ctrl+F1 brings
up any additional bios settings
--
JS
http://www.pagestart.com
"Pool" wrote in message
...
Hi JS
Here are the specifications of both new and old RAM
Elixir 256MB DDR-400MHZ , PC3200U-30330
N2DS25680BT-ST
0351.EME03C1201B.120393M.XX.TW
Kingston: 1GB DDR PC-3200
ELPIDA , D5108AGTA-5B-E
CT1GD64SH08BL-5T
I tried installing one stick of 1GB then i booted it worked normally.Then
when i tried booting again it took around 20 seconds to boot up.I tried
booting a third time it didn't boot at all.Now i am using old RAM.Is it a
RAM
problem or is it something with the power supply.Please help.
"JS" wrote:
There is a Elixir Part number, see the web site link below
and use there part numbering scheme, when you post back
the actual part number then I can do a better comparison.
http://www.elixir-memory.com/sup_name_rul_2.asp
Also you Gigabyte motherboard uses "MIT's" technology
which has been know to cause the PC to fail to boot on socket 775
motherboards when you first install new memory, this may or may not
be the case with the older sockets 478 motherboards.
The solution is to only install one memory stick and power up
the PC and let the BIOS "learn" the memory requirements
and then after a few successful reboots then install the second
memory stick.
--
JS
http://www.pagestart.com
"Pool" wrote in message
...
Hi Everyone
Thank you so much for trying to help me solve the problem i am having.
I checked Memory frequency in Bios and here what i found
Memory Frequency For [Auto]
Memory Frequency(MHZ) 400
AGP/PCI/SRC Frequency(MHZ) 66/33/100
Also here is what written on the old RAM which came with the
computer,Please tell me if it is the same compatible with the new RAM i
bought recently.Now i installed old RAM inorder to be able to use the
computer.
Old RAM : Two sticks of Elixir 256MB DDR-400MHZ, CL3 PC3200U-30330
New RAM: Two sticks of Kingston 1GB DDR PC-3200
Motherboard: Gigabyte Pentium 4 Titan Series, GA-8IPE1000-L Series
FSB 800 , Dual DDR 400, AGP 8X, 2004 GT
Edition
Processor : 3.0GHZ Socket 478
I am not trying to install old RAM with new RAM,i am trying to only
install
the new RAM i got because i want more memory.If you can tell me if the
above
specifications are compatible i would be very much appreciated.Thanks
again
"JS" wrote:
Kingston Gigabyte GA-8IPE1000/GA-8IPE1000-L Recommended Memory:
http://www.ec.kingston.com/ecom/conf...submit1=Search
Kingston KVR800D2N6/1G Specs:
http://www.ec.kingston.com/ecom/conf...00D2N6/1G&id=1
Also check the FSB speed for your Intel Processor
Motherboard manual (Page 55), BIOS setting = Memory Frequency For
[Auto]
--
JS
http://www.pagestart.com
"Pool" wrote in message
...
Hi JS
I didn't install both RAMs old and new ones at the same time.Now i
only
have the old ones which are installed.I even tried to only install
one
Stick
of the new RAM in a different slot and still didn't work.I wrote you
the
model of the new RAM i got a little while ago
The computer is a home built
Motherboard: Gigabyte Pentium 4 Titan Series GA-8IPE1000-L , 2004 GT
Edition
Chipset: Intel 865PE, FSB 800, Dual DDR 400, AGP 8x
Processor: Intel 3.0 MHZ Socket 478
Hope that helps.Thanks again
"Pool" wrote:
Hi JS
here is what written on the box of the RAM i bought please tell me
if
it
is
compatible with the motherboard i have
Kingston: KVR800D2N6/1G
1GB PC2-6400 CL6 240-Pin DIMM
On the stick of RAM is written : 1GB DDR PC-3200
CT1GD64SH08BL-5T
Thanks again
"Pool" wrote:
Hi JS
I already done that test and it gave me no errors.That is why i
don't
know
if it is a RAM problem or something related to PSU.You said it
could
be
a
case of a wrong memory for my PC how should i know if this is the
case.Motherboard handles till 4GB beside new RAM and old ones
both
have
same
bus 400.Help me please.
"JS" wrote:
Try running Memtest86+, this runs from a boot disk or CD
and should eliminate or confirm if your ram is bad. Install
only your Kingston memory before you start the test.
Let it run for as long as you can, 2,4,6,8 or more hours,
if no errors by then your ram is OK, but this appears to be
a case of the wrong memory for your PC and I would expect
it will fail within a short period of time is you are even able
to
boot from the memtest CD or floppy.
See: http://www.memtest.org/
Also use the Crucial Memory Advisor Tool
http://www.crucial.com/store/listmfgr.asp?cat=RAM
Compare how close the specs are between what
Crucial recommends and what the specs are for your
Kingston memory.
--
JS
http://www.pagestart.com
"Pool" wrote in message
...
Hi
Recently i installed new Kingston RAM two sticks of 1GB
wanted
to
upgrade
since i had 512MB RAM.After i installed new RAM computer took
around 20
seconds to boot up,power light,hard disk and fans all working
but
no beep
that happens at first when you boot up computer and nothing
on
the
screen.Then it booted up normally.Couple of days ago when i
started
computer
it didn't boot at all.Only power light,hard disk and fans are
working but
again nothing on the screen and no POST beep.
I took off new RAM and installed the old ones that came with
the
computer.It booted up normally without any problem.
Is it a problem with the new RAM i bought or a power supply
problem.Please
help me solve this problem.
Specification of the new RAM i got is : two sticks of
Kingston
1GB
DDR
PC-3200
Old RAM are 2x256MB 400MHZ
Computer specification
Motherboard: Gigabyte Pentium 4 Titan Series GA-8IPE1000
Series
Intel 865 PE, FSB 800
Dual DDR 400
AGP 8x
Power supply: Infinity 450W
Video card: ATI 7500
Operating System: Windows XP Home Service Pack 2
Any help would be very much appreciated