N
"Larry" wrote in message
...
:
: "Andy I."
[email protected] wrote in message
: ...
:
: "Larry" wrote in message
: ...
::
:: "Andy I."
[email protected] wrote in message
:: ...
::
:: "Lem" lemp40@unknownhost wrote in message
:: ...
::: Andy I. wrote:
::: Hi,
:::
::: I have recently acquired a used HP PSC 1600 All-In One. The test
: print
:: is
::: OK. Regular printing (without using the scanner) seems OK.
::: My first attempt at "Copy" resulted in a perfect b/w print except for
a
::: solid black stripe running down the full length of the paper, 11" long
: X
::: 9/16" wide. (28 cm X 14 mm).
:::
::: I would greatly appreciate a solution to this problem.
::: Andy I. (WIN XP SP3; IE 7; OE 6)
:::
:::
:::
::: There's generally a reason that a *used* device is sold by the original
::: buyer. Often, that reason is because the device no longer works as well
::: as it did when it was new.
:::
::: Or see:
:::
::
:
http://h10025.www1.hp.com/ewfrf/wc/d...434551&lang=en
:::
::: --
::: Lem
:::
::: Apollo 11 - 40 years ago:
:::
http://www.nasa.gov/mission_pages/ap...0th/index.html
::
:: Thank you Lem. The link you provided seemed to portray the symptom I am
:: experiencing, but none of the suggested remedies worked for me. The
final
:: check was an interesting idea, copying a *blank* sheet of paper. The
: result
:: for me was the same 14 mm - wide black stripe.........
::
:: The instructions were to copy that blank sheet in *black*. I've just had
:: the brilliant idea to try copy *color*! Result - the same *black*
stripe!
::
:: Puzzled.
:: Andy I.
::
:: *****
::
:: Hi Andy,
::
:: I had an HP All in One that had a similar problem. What I did to get rid
: of
:: it was to remove the cover and tighten the screws that mount the main
: board
:: to the metal frame. These screw points are common grounds that connect
: each
:: other through the frame. You might also try (with the plug removed)
:: reseating all the plugs that go to the boards.
::
:: Good Luck!
::
:: Larry
:: Australia
::
::
: Thanks Larry. I'll try that.
:
: Andy I.
:
: Hello again Larry. No joy there. I lifted the scanner cover and removed
: four screws, but couldn't get any further. I don't see any metal anywhere
: in this All-In-One. I have a worn out ten-year old HP DeskJet 882C
printer,
: which I'd hoped that this All-In-One would replace. The old printer does
: have obvious metal parts.
:
: Andy I.
: *****
: Andy,
:
: Mine was an 1170c from around 1999- 2000 era. The back came off and there
: was 2 vertically mounted boards accessable after you removed a plate
inside
: the plastic cover. Looking at a photo on the net of the PSC1600, this
looks
: quite a bit more modern than the 1170c.
:
: Try:
:
http://h10025.www1.hp.com/ewfrf/wc/d...390315&lang=en
:
:
: Support page for that model printer:
:
http://h10025.www1.hp.com/ewfrf/wc/d...product=390315
:
: It doesn't look like you are alone with that problem.
:
: Larry
:
Hi Larry,
Now she tells me!.................. My daughter gave me this used
All-In-One and now she tells me the scanner doesn't
work..................!**/!!?! "It's good
for printing", she says.........
What I'll do now is hook up my old Umax Astra 1220P scanner (which DOES
work) to the All-In-One. If I'd known I would have done this in the first
place. I won't be able to do the one-button "Copy", but what the ****!
Many thanks for your continued concern and the advice you provided.
Andy I.