A Windows XP help forum. PCbanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » PCbanter forum » Microsoft Windows XP » General XP issues or comments
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Dual booting



 
 
Thread Tools Display Modes
  #1  
Old January 4th 05, 11:31 PM
Peter Will
external usenet poster
 
Posts: n/a
Default Dual booting

What would be the best forum to post a message for help about setting a
computer up with dual boot of XP and Me?


Ads
  #2  
Old January 5th 05, 12:01 AM
Dan DiNicolo
external usenet poster
 
Posts: n/a
Default Dual booting

You can find details he

http://support.microsoft.com/kb/217210

--
Dan DiNicolo
MCSE, CCNP, CCDA
http://www.2000trainers.com

"Peter Will" wrote in message
...
What would be the best forum to post a message for help about setting a
computer up with dual boot of XP and Me?



  #3  
Old January 5th 05, 12:28 AM
R. C. White
external usenet poster
 
Posts: n/a
Default Dual booting

Hi, Peter.

This newsgroup is fine. The question comes up often here, and a scan of
prior messages might have saved you the effort of asking it again.

In brief, the answer is that the process can be complicated if you've
already installed WinXP and want to add WinME, especially if your Drive C:
is formatted NTFS. But, if you want to add WinXP to an existing WinME, and
if you have at least one additional partition (on any HD in your computer)
to install WinXP into, then the process is very easy: Just boot from the
WinXP CD-ROM and follow the prompts to install it into that other partition.
WinXP Setup will automatically create the dual-boot system.

If you need more details, please post back, giving more details, especially
which OS is already installed, how many HDs you have and how they are
partitioned and formatted. It might be important to know a few more
details, such as make and model of computer (or mobo/chipset if you built it
yourself), and whether your HDs are other than the generic IDE/ATA type. We
won't know what else to ask you until we know some of these things.

RC
--
R. C. White, CPA
San Marcos, TX

Microsoft Windows MVP

"Peter Will" wrote in message
...
What would be the best forum to post a message for help about setting a
computer up with dual boot of XP and Me?


  #4  
Old January 5th 05, 01:41 AM
Peter Will
external usenet poster
 
Posts: n/a
Default Dual booting

Thanks for the reply. I followed a lot of disjointed info on the Microsoft
help site and did the following. I have two hard drives, a Seagate 40 (C
and a WD 20 (D. I partitioned the 40 to 31 (partition 1) and 9 (partition
2). Microsoft was imperative about the order for loading so I set up Me
first on partition 2. At that point it would boot into Me without problem.
I then installed XP on partition 1. I then had to modify boot.ini to list
the send version (Me). The operating systems listing looks like this
multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Micro soft
Windows XP Home Edition"
multi(0)disk(0)rdisk(0)partition(2)\WINDOWS="Micro soft
Windows Millennium Edition"
When I boot I have the list of choices for both of those. It will boot
without problem into XP but when I select the Me it will not boot but comes
up with the "hal.dll" error. I have followed Microsoft's Knowledge Base
suggestions and booted from the XP CD and used 'bootcfg'. Scan and list
does not find the Me installation. The only way I have found to get the
entry into the boot.ini is to enter it manually. That kind of states the
problem.
"Dan DiNicolo" wrote in message
...
You can find details he

http://support.microsoft.com/kb/217210

--
Dan DiNicolo
MCSE, CCNP, CCDA
http://www.2000trainers.com

"Peter Will" wrote in message
...
What would be the best forum to post a message for help about setting a
computer up with dual boot of XP and Me?





  #5  
Old January 5th 05, 01:42 AM
Peter Will
external usenet poster
 
Posts: n/a
Default Dual booting

Thanks for the reply. I followed a lot of disjointed info on the Microsoft
help site and did the following. I have two hard drives, a Seagate 40 (C
and a WD 20 (D. I partitioned the 40 to 31 (partition 1) and 9 (partition
2). Microsoft was imperative about the order for loading so I set up Me
first on partition 2. At that point it would boot into Me without problem.
I then installed XP on partition 1. I then had to modify boot.ini to list
the send version (Me). The operating systems listing looks like this
multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Micro soft
Windows XP Home Edition"
multi(0)disk(0)rdisk(0)partition(2)\WINDOWS="Micro soft
Windows Millennium Edition"
When I boot I have the list of choices for both of those. It will boot
without problem into XP but when I select the Me it will not boot but comes
up with the "hal.dll" error. I have followed Microsoft's Knowledge Base
suggestions and booted from the XP CD and used 'bootcfg'. Scan and list
does not find the Me installation. The only way I have found to get the
entry into the boot.ini is to enter it manually. That kind of states the
problem.
"R. C. White" wrote in message
...
Hi, Peter.

This newsgroup is fine. The question comes up often here, and a scan of
prior messages might have saved you the effort of asking it again.

In brief, the answer is that the process can be complicated if you've
already installed WinXP and want to add WinME, especially if your Drive C:
is formatted NTFS. But, if you want to add WinXP to an existing WinME,
and if you have at least one additional partition (on any HD in your
computer) to install WinXP into, then the process is very easy: Just boot
from the WinXP CD-ROM and follow the prompts to install it into that other
partition. WinXP Setup will automatically create the dual-boot system.

If you need more details, please post back, giving more details,
especially which OS is already installed, how many HDs you have and how
they are partitioned and formatted. It might be important to know a few
more details, such as make and model of computer (or mobo/chipset if you
built it yourself), and whether your HDs are other than the generic
IDE/ATA type. We won't know what else to ask you until we know some of
these things.

RC
--
R. C. White, CPA
San Marcos, TX

Microsoft Windows MVP

"Peter Will" wrote in message
...
What would be the best forum to post a message for help about setting a
computer up with dual boot of XP and Me?




  #6  
Old January 5th 05, 03:57 AM
Bruce Chambers
external usenet poster
 
Posts: n/a
Default Dual booting

Peter Will wrote:
What would be the best forum to post a message for help about setting a
computer up with dual boot of XP and Me?




This is as good a place as any, I should think. There is no Microsoft
newsgroup dedicated solely to dual-booting.

The simplest way I've found to dual boot between Win9x/Me and WinXP
would be to partition your drive(s) roughly as follows:

C: Primary FAT32 Win9x/Me/Legacy Apps
D: Extended NTFS WinXP/Modern Apps

Adjust the partition sizes according to your actual hard drive(s)
size and the amount of space you'd like to allocate to each OS and its
applications.

Create the partitions using Win9x's FDISK so you can enable large
disk support (FAT32). (No need for 3rd party partitioning
utilities/boot managers and their frequent complications.)

Install Win9x/Me first, being sure to select "C:\Windows" (or
D:\Windows, if you prefer) when asked for the default Windows
directory. When you subsequently install WinXP, be sure to specify
"D:\Winnt" (or "D:\Windows," "C:\Winnt" as referred/applicable) when
asked for the default Windows directory, to place it in the other
partition. The WinXP installation routine will automatically set up a
Multi-boot menu for you. The default settings for this menu can be
readily edited from within WinXP. NOTE: If you elect to place
Win9x/Me on the "D:" drive, you'll _have_ to leave the "C:" drive as
FAT32.

This method can be adapted to using 2 physical hard drives by
placing the boot partition (C:, which still must be FAT32) and either
of the operating systems on the Primary Master hard drive, and the
second operating system on the second hard drive.

It is also possible to have a 3rd partition for shared
applications, but it would be necessary for such a partition to be
formatted in the common file format (FAT32). The applications would
also have to be installed into each OS (to ensure proper system file
placement and registry updates), one at a time, but the bulk of the
program files could be located on this common partition. I do not,
however, actually recommend doing this as, if you were to uninstall
such an application from one OS, you may not be able to gracefully
uninstall it from the second OS, having already deleted crucial
installation data during the first uninstall action.

Just about everything you need to know (URLs may wrap):

http://support.microsoft.com/support.../Q217/2/10.ASP

http://www.microsoft.com/windowsxp/p.../multiboot.asp


--

Bruce Chambers

Help us help you:
http://dts-l.org/goodpost.htm
http://www.catb.org/~esr/faqs/smart-questions.html

You can have peace. Or you can have freedom. Don't ever count on having
both at once. - RAH
  #7  
Old January 5th 05, 04:00 AM
Bruce Chambers
external usenet poster
 
Posts: n/a
Default Dual booting

Peter Will wrote:
Thanks for the reply. I followed a lot of disjointed info on the Microsoft
help site and did the following. I have two hard drives, a Seagate 40 (C
and a WD 20 (D. I partitioned the 40 to 31 (partition 1) and 9 (partition
2). Microsoft was imperative about the order for loading so I set up Me
first on partition 2. At that point it would boot into Me without problem.
I then installed XP on partition 1. I then had to modify boot.ini to list
the send version (Me). The operating systems listing looks like this
multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Micro soft
Windows XP Home Edition"
multi(0)disk(0)rdisk(0)partition(2)\WINDOWS="Micro soft
Windows Millennium Edition"
When I boot I have the list of choices for both of those. It will boot
without problem into XP but when I select the Me it will not boot but comes
up with the "hal.dll" error. I have followed Microsoft's Knowledge Base
suggestions and booted from the XP CD and used 'bootcfg'. Scan and list
does not find the Me installation. The only way I have found to get the
entry into the boot.ini is to enter it manually. That kind of states the
problem.



It sounds like, during the WinXP installation, you may have formatted
and possibly converted "partition 1" to NTFS. This would have
immediately rendered the WinME installation unbootable. IT's essential
system files were still located on "partition 1."

--

Bruce Chambers

Help us help you:
http://dts-l.org/goodpost.htm
http://www.catb.org/~esr/faqs/smart-questions.html

You can have peace. Or you can have freedom. Don't ever count on having
both at once. - RAH
  #8  
Old January 5th 05, 04:58 AM
Peter Will
external usenet poster
 
Posts: n/a
Default Dual booting

Thank you for the info

"Bruce Chambers" wrote in message
...
Peter Will wrote:
What would be the best forum to post a message for help about setting a
computer up with dual boot of XP and Me?



This is as good a place as any, I should think. There is no Microsoft
newsgroup dedicated solely to dual-booting.

The simplest way I've found to dual boot between Win9x/Me and WinXP
would be to partition your drive(s) roughly as follows:

C: Primary FAT32 Win9x/Me/Legacy Apps
D: Extended NTFS WinXP/Modern Apps

Adjust the partition sizes according to your actual hard drive(s)
size and the amount of space you'd like to allocate to each OS and its
applications.

Create the partitions using Win9x's FDISK so you can enable large disk
support (FAT32). (No need for 3rd party partitioning utilities/boot
managers and their frequent complications.)

Install Win9x/Me first, being sure to select "C:\Windows" (or
D:\Windows, if you prefer) when asked for the default Windows
directory. When you subsequently install WinXP, be sure to specify
"D:\Winnt" (or "D:\Windows," "C:\Winnt" as referred/applicable) when
asked for the default Windows directory, to place it in the other
partition. The WinXP installation routine will automatically set up a
Multi-boot menu for you. The default settings for this menu can be
readily edited from within WinXP. NOTE: If you elect to place
Win9x/Me on the "D:" drive, you'll _have_ to leave the "C:" drive as
FAT32.

This method can be adapted to using 2 physical hard drives by
placing the boot partition (C:, which still must be FAT32) and either
of the operating systems on the Primary Master hard drive, and the
second operating system on the second hard drive.

It is also possible to have a 3rd partition for shared
applications, but it would be necessary for such a partition to be
formatted in the common file format (FAT32). The applications would
also have to be installed into each OS (to ensure proper system file
placement and registry updates), one at a time, but the bulk of the
program files could be located on this common partition. I do not,
however, actually recommend doing this as, if you were to uninstall
such an application from one OS, you may not be able to gracefully
uninstall it from the second OS, having already deleted crucial
installation data during the first uninstall action.

Just about everything you need to know (URLs may wrap):

http://support.microsoft.com/support.../Q217/2/10.ASP

http://www.microsoft.com/windowsxp/p.../multiboot.asp


--

Bruce Chambers

Help us help you:
http://dts-l.org/goodpost.htm
http://www.catb.org/~esr/faqs/smart-questions.html

You can have peace. Or you can have freedom. Don't ever count on having
both at once. - RAH



  #9  
Old January 5th 05, 05:03 AM
Kelly
external usenet poster
 
Posts: n/a
Default Dual booting

Added info, if needed:

How to Install Windows 98/Me after Installing Windows XP
http://www.dougknox.com/xp/tips/xp_repair_9x.htm

How to Install W2K to its Own Partition after installing XP
http://www.dougknox.com/xp/tips/xp_repair_2k.htm

--
Happy New Year,
Kelly (MS-MVP)

Troubleshooting Windows XP
http://www.kellys-korner-xp.com


"Peter Will" wrote in message
...
Thank you for the info

"Bruce Chambers" wrote in message
...
Peter Will wrote:
What would be the best forum to post a message for help about setting a
computer up with dual boot of XP and Me?



This is as good a place as any, I should think. There is no Microsoft
newsgroup dedicated solely to dual-booting.

The simplest way I've found to dual boot between Win9x/Me and WinXP
would be to partition your drive(s) roughly as follows:

C: Primary FAT32 Win9x/Me/Legacy Apps
D: Extended NTFS WinXP/Modern Apps

Adjust the partition sizes according to your actual hard drive(s)
size and the amount of space you'd like to allocate to each OS and its
applications.

Create the partitions using Win9x's FDISK so you can enable large
disk support (FAT32). (No need for 3rd party partitioning utilities/boot
managers and their frequent complications.)

Install Win9x/Me first, being sure to select "C:\Windows" (or
D:\Windows, if you prefer) when asked for the default Windows
directory. When you subsequently install WinXP, be sure to specify
"D:\Winnt" (or "D:\Windows," "C:\Winnt" as referred/applicable) when
asked for the default Windows directory, to place it in the other
partition. The WinXP installation routine will automatically set up a
Multi-boot menu for you. The default settings for this menu can be
readily edited from within WinXP. NOTE: If you elect to place
Win9x/Me on the "D:" drive, you'll _have_ to leave the "C:" drive as
FAT32.

This method can be adapted to using 2 physical hard drives by
placing the boot partition (C:, which still must be FAT32) and either
of the operating systems on the Primary Master hard drive, and the
second operating system on the second hard drive.

It is also possible to have a 3rd partition for shared
applications, but it would be necessary for such a partition to be
formatted in the common file format (FAT32). The applications would
also have to be installed into each OS (to ensure proper system file
placement and registry updates), one at a time, but the bulk of the
program files could be located on this common partition. I do not,
however, actually recommend doing this as, if you were to uninstall
such an application from one OS, you may not be able to gracefully
uninstall it from the second OS, having already deleted crucial
installation data during the first uninstall action.

Just about everything you need to know (URLs may wrap):

http://support.microsoft.com/support.../Q217/2/10.ASP

http://www.microsoft.com/windowsxp/p.../multiboot.asp


--

Bruce Chambers

Help us help you:
http://dts-l.org/goodpost.htm
http://www.catb.org/~esr/faqs/smart-questions.html

You can have peace. Or you can have freedom. Don't ever count on having
both at once. - RAH





  #10  
Old January 6th 05, 10:52 PM
R. C. White
external usenet poster
 
Posts: n/a
Default Dual booting

Hi, Peter.

It appears you have misunderstood much of the "disjointed info" you have
received. :( Maybe it's time for the long version of my usual description
of Microsoft's dual boot scenario.

First, C: is not your physical hard drive. A hard drive is never assigned a
"drive" letter. That's a misnomer which we won't be able to change because
it is so ingrained in the literature and language of computing. "Drive"
letters actually are assigned to "volumes". Each hard drive can be
partitioned into 1, 2, 3 or 4 partitions, of which one may be an "extended
partition"; the others are "primary partitions". Multiple "logical drives"
can be created within the extended partition; there's no limit on how many
logical drives until you run out of disk space or letters of the English
alphabet. The extended partition is not assigned a drive letter, but each
logical drive in it gets a letter. Each primary partition and each logical
drive is a "volume", and each one is assigned a "drive letter". Each volume
is formatted independently from other volumes. During the boot process, the
BIOS reserves letters A and B for floppy drives, then assigns C to the
Active primary partition, and other letters to other primary partitions and
logical drives on all hard drives, in order according to the algorithm built
into the BIOS.

Only a primary partition can be marked Active and used to boot the computer.
Typically, this is the first physical partition on the first hard drive in
the computer. When the computer power is turned on, it's quite ignorant.
All it knows is what's hard-wired into it, including the code in the
read-only BIOS chip, as modified by settings we make in the semi-permanent
CMOS (what we usually mean when we say we are changing the BIOS settings).
About all the BIOS knows is to find the first hard disk and read the first
physical sector on it, which is the MBR - the Master Boot Record. The MBR
includes the partition table telling where each partition begins and ends,
how it's formatted, and which one is the Active (bootable) partition. The
computer finds the first physical sector on that Active partition, loads the
512 bytes of code from it into memory and executes that code.

The boot sector of the Active partition is the key to everything that comes
after that. If it is the older MS-DOS style boot sector, it tells the
computer to look in the Root of the System Partition for the files io.sys
and msdos.sys, load those files, and use them to start MS-DOS. Depending on
the contents of msdos.sys, it will either boot into MS-DOS, or use MS-DOS to
find the Win9x/ME "boot folder", wherever it may be, and load and start
running Win9x/ME. This is typically C:\Windows, but it can be in any volume
on any hard drive in the computer. Note that the process always starts in
C:, the "System Partition", and branches from there to the "boot volume",
where the boot folder is installed - which may or may not be right back to
C: again.

The NT-style boot sector does not look for io.sys and msdos.sys; it looks in
the Root of the System Partition for the NT-type "system files", NTLDR,
NTDETECT.COM and Boot.ini. C:\NTLDR uses C:\Boot.ini to choose which
operating system to start and to locate the chosen one. If WinXP Setup
detects Win9x/ME during installation of WinXP, it first saves the
MS-DOS-style boot sector into a new file, C:\bootsect.dos. Then it writes
the NT boot sector and system files. It adds a final line to C:\boot.ini
reading something like: C:\="Microsoft Windows ME". Then it installs WinXP
into WinXP's boot folder (\Windows, by default) on WinXP's boot volume,
which, again, can be just about any volume on any HD in your computer.

Thereafter, each time you reboot, C:\NTLDR uses C:\Boot.ini to present the
OS menu. If you choose WinME, NTLDR loads the MS-DOS boot sector from
C:\bootsect.dos, turns control over to it, and WinXP "retires from the
field". From then on, it's as though WinXP did not exist on your computer,
except for all the space used by its files. Bootsect.dos loads io.sys and
msdos.sys and WinME starts as usual.

If you choose WinXP to boot, NTLDR looks where Boot.ini points, loads WinXP
and starts it running. From then on, it's as though WinME did not exist on
your computer, except for the space it uses. The system used to locate
WinXP in boot.ini is by HD number (referred to usually as rdisk(#)) and
volume number (referred to as partition(#)). It's important to remember
that HDs are numbered starting with zero, partitions are numbered starting
with one on each HD, and that "partition" actually means "volume", because
logical drives are included in the count.


With all that out of the way, let's take a look at your situation.

I have two hard drives, a Seagate 40 (C and a WD 20 (D.


No. You have Drive 0, the 40-gig, and Drive 1, the 20-gig.

I partitioned the 40 to 31 (partition 1) and 9 (partition 2).


Now you have Drive C:, the first primary partition on Drive 0. This is the
Active (bootable) partition on the first physical drive, so it becomes the
System Partition for your computer. Drive C: is 31 GB.

The other drive letters depend on several things - and they may be different
in the BIOS, in MS-DOS, in WinME and in WinXP! :(

If you decide to format any volume using NTFS, then WinME will not be able
to read, write, boot from or even SEE that volume! Since the boot process
must always start with the System Partition, C: MUST be formatted FATxx if
you plan to install WinME anywhere on this computer. Whichever volume you
plan to install WinME into must also be formatted FAT. And any volume
holding files that you plan to access from WinME must also be formatted FAT.
Because of this limitation, dual-boot systems that include Win9x/ME often
use FAT for all volumes. If NTFS is used for some volumes, WinME won't be
able to even see those volumes, and this is one reason that drive letters
may be different when booted into WinME than when booted into WinXP.

What kind of partition (primary partition or logical drive) is the 9 GB on
Drive 0? And what kind of partition did you create on Drive 1? Assuming
they are both primary partitions, then the BIOS would assign D: to the first
primary partition on HD1, then go back and assign E: to the second primary
partition on HD0. MS-DOS would agree with that assignment, and so would
Win98. But WinME would first assign letters to all primary partitions on
HD0 before looking at HD1, so your 9 GB partition on HD0 would be D: and the
20 GB partition on HD1 would be E:. WinXP would agree with WinME. Now that
I've said all that so positively, let me back up and admit that I'm not sure
it is correct. My point is that "drive letters" are not permanent; they are
assigned from scratch anew each time the computer is booted, depending on
the operating system and on the hardware configuration at that boot time.
The hardware configuration may include CD/DVD drives, removable "drives"
(such as USB "thumb" drives, cameras and scanners), and network drives, all
of which may be assigned letters, depending on what is plugged in at boot
time. But if we use Device Manager (in WinME) or Disk Management (in WinXP)
to specifically assign drive letters (except for the System Partition and
Boot Volume), the Windows will attempt to assign those same letters to the
same drives each time it reboots.

All that is far too complex for this discussion. Let's just assume that all
your volumes are formatted FAT32 and that the letters assigned a
C: - 31 GB - rdisk(0)partition(1) - WinXP is installed in C:\Windows
D: - 9 GB - rdisk(0)partition(2) - WinME is installed in D:\Windows
E: - 20 GB - rdisk(1)partition(1) - for applications and data; no OS here

I set up Me first on partition 2. At that point it would boot into Me
without problem.


Fine. WinME's boot volume would be D:\Windows.

I then installed XP on partition 1.


OK. WinXP's boot volume would be C:\Windows.

I then had to modify boot.ini to list the send version (Me). The
operating systems listing looks like this
multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Micro soft
Windows XP Home Edition"
multi(0)disk(0)rdisk(0)partition(2)\WINDOWS="Micro soft
Windows Millennium Edition"


Wrong! First, you should not have had to modify C:\boot.ini at all. WinXP
Setup should have configured it properly. And second, the line to load
Win9x/ME should not look at all like the one to load Win2K/XP, etc. As I
showed above, it should read:
C:\="Microsoft Windows Millennium Edition"

It should always point to C:\, because that's where C:\bootsect.dos is. The
actual location of WinME will be stored in C:\msdos.sys. The label between
the quotes is ignored by the computer. It is only for the benefit of us
humans so we recognize it when we see it in the menu. If you like, it can
simply say "ME" or whatever you choose.

The line for WinXP looks correct IF WinXP is installed on C:, the first
partition on the first HD, which you say it is. This line might end with
some optional switches, such as /fastdetect or /NoExecute=OptIn, but those
are not always required.

When I boot I have the list of choices for both of those.


Right, because the menu from C:\boot.ini is just printed onscreen. Even
though the WinME line is not correct, the menu will still show the label
within the quotes.

It will boot without problem into XP


Right, because the WinXP line is properly formatted and points to
C:\Windows, although the "C:" doesn't appear in boot.ini.

but when I select the Me it will not boot but comes up with the "hal.dll"
error.


No, because that improper WinME line thoroughly confuses NTLDR. It ignores
the label between the quotes and tries to find some version of WinNT/2K/XP
in the second partition on the first HD - and doesn't find anything it
recognizes there, so it throws up its hands, picks an error message from
somewhere, and says, in effect, "I don't now how to do what you are telling
me to do."

I have followed Microsoft's Knowledge Base suggestions and booted from the
XP CD and used 'bootcfg'. Scan and list does not find the Me
installation. The only way I have found to get the entry into the
boot.ini is to enter it manually.


I'm not sure of the exact workings of bootcfg.exe, but I suspect that it
does not recognize your WinME, perhaps because bootsect.dos, io.sys and
msdos.sys are not in C:\.

If my assumptions stated much earlier are correct, then your C:\boot.ini
should read like this (the timeout value is the 5 seconds I use; you can
change this to suit yourself):

[boot loader]
timeout=5
default=multi(0)disk(0)rdisk(0)partition(1)\WINDOW S
[operating systems]
multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Micro soft Windows XP Home
Edition"
C:\="Microsoft Windows Millennium Edition"


Well, I warned you this would be the long version, Peter. To read more
about boot.ini, see the online version of the WinXP Pro Resource Kit:
http://www.microsoft.com/resources/d...k_overview.asp

Sometimes the URL does not take you directly to the page I have in mind, but
you can drill down to Part VI, System Troubleshooting, then to Chapter 28,
Troubleshooting Startup / Following a Process for Startup and Recovery, then
Reviewing and Correcting Boot.ini Settings on x86-based Systems

If you get lost, explore. You'll find TONS of good information about disk
and file systems in that book. I've found it well worth my money to buy the
RK and my time to read much of it. A few hours invested in reading and
understanding these chapters will pay dividends, not just for this week, but
for as long as I continue to use computers, which will probably be for the
rest of my life.

At this stage, your best bet would probably be to first boot from the WinME
CD-ROM and reinstall WinME from scratch on D:. Then boot from the WinXP
CD-ROM and reinstall WinXP as a clean install on C:, letting it recreate
C:\boot.ini from scratch.

Post back if you have further problems or questions.

RC
--
R. C. White, CPA
San Marcos, TX

Microsoft Windows MVP

PS: It is NOT necessary to email me in addition to posting here in the
newsgroup.

"Peter Will" wrote in message
...
Thanks for the reply. I followed a lot of disjointed info on the
Microsoft help site and did the following. I have two hard drives, a
Seagate 40 (C and a WD 20 (D. I partitioned the 40 to 31 (partition
1) and 9 (partition 2). Microsoft was imperative about the order for
loading so I set up Me first on partition 2. At that point it would boot
into Me without problem. I then installed XP on partition 1. I then had
to modify boot.ini to list the send version (Me). The operating systems
listing looks like this
multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Micro soft
Windows XP Home Edition"
multi(0)disk(0)rdisk(0)partition(2)\WINDOWS="Micro soft
Windows Millennium Edition"
When I boot I have the list of choices for both of those. It will boot
without problem into XP but when I select the Me it will not boot but
comes up with the "hal.dll" error. I have followed Microsoft's Knowledge
Base suggestions and booted from the XP CD and used 'bootcfg'. Scan and
list does not find the Me installation. The only way I have found to get
the entry into the boot.ini is to enter it manually. That kind of states
the problem.
"R. C. White" wrote in message
...
Hi, Peter.

This newsgroup is fine. The question comes up often here, and a scan of
prior messages might have saved you the effort of asking it again.

In brief, the answer is that the process can be complicated if you've
already installed WinXP and want to add WinME, especially if your Drive
C: is formatted NTFS. But, if you want to add WinXP to an existing
WinME, and if you have at least one additional partition (on any HD in
your computer) to install WinXP into, then the process is very easy:
Just boot from the WinXP CD-ROM and follow the prompts to install it into
that other partition. WinXP Setup will automatically create the dual-boot
system.

If you need more details, please post back, giving more details,
especially which OS is already installed, how many HDs you have and how
they are partitioned and formatted. It might be important to know a few
more details, such as make and model of computer (or mobo/chipset if you
built it yourself), and whether your HDs are other than the generic
IDE/ATA type. We won't know what else to ask you until we know some of
these things.

RC

"Peter Will" wrote in message
...
What would be the best forum to post a message for help about setting a
computer up with dual boot of XP and Me?


  #11  
Old January 7th 05, 04:22 AM
Peter Will
external usenet poster
 
Posts: n/a
Default Dual booting

I got your further posting and I have to thank you for such a phenomenal
explanation and taking the time to describe all that, and I am not being
facetious. I applied all that information (and now understand why). The KB
probably did have it hidden in there but not in all one place and it was not
clear that the Me had to go on the primary. It is all working wonderfully
now and thank you again.

Peter
"R. C. White" wrote in message
...
Hi, Peter.

This newsgroup is fine. The question comes up often here, and a scan of
prior messages might have saved you the effort of asking it again.

In brief, the answer is that the process can be complicated if you've
already installed WinXP and want to add WinME, especially if your Drive C:
is formatted NTFS. But, if you want to add WinXP to an existing WinME,
and if you have at least one additional partition (on any HD in your
computer) to install WinXP into, then the process is very easy: Just boot
from the WinXP CD-ROM and follow the prompts to install it into that other
partition. WinXP Setup will automatically create the dual-boot system.

If you need more details, please post back, giving more details,
especially which OS is already installed, how many HDs you have and how
they are partitioned and formatted. It might be important to know a few
more details, such as make and model of computer (or mobo/chipset if you
built it yourself), and whether your HDs are other than the generic
IDE/ATA type. We won't know what else to ask you until we know some of
these things.

RC
--
R. C. White, CPA
San Marcos, TX

Microsoft Windows MVP

"Peter Will" wrote in message
...
What would be the best forum to post a message for help about setting a
computer up with dual boot of XP and Me?




  #12  
Old January 7th 05, 02:53 PM
R. C. White
external usenet poster
 
Posts: n/a
Default Dual booting

Hi, Peter.

It is all working wonderfully now and thank you again.


;)

RC
--
R. C. White, CPA
San Marcos, TX

Microsoft Windows MVP

"Peter Will" wrote in message
...
I got your further posting and I have to thank you for such a phenomenal
explanation and taking the time to describe all that, and I am not being
facetious. I applied all that information (and now understand why). The
KB probably did have it hidden in there but not in all one place and it was
not clear that the Me had to go on the primary. It is all working
wonderfully now and thank you again.

Peter
"R. C. White" wrote in message
...
Hi, Peter.

This newsgroup is fine. The question comes up often here, and a scan of
prior messages might have saved you the effort of asking it again.

In brief, the answer is that the process can be complicated if you've
already installed WinXP and want to add WinME, especially if your Drive
C: is formatted NTFS. But, if you want to add WinXP to an existing
WinME, and if you have at least one additional partition (on any HD in
your computer) to install WinXP into, then the process is very easy:
Just boot from the WinXP CD-ROM and follow the prompts to install it into
that other partition. WinXP Setup will automatically create the dual-boot
system.

If you need more details, please post back, giving more details,
especially which OS is already installed, how many HDs you have and how
they are partitioned and formatted. It might be important to know a few
more details, such as make and model of computer (or mobo/chipset if you
built it yourself), and whether your HDs are other than the generic
IDE/ATA type. We won't know what else to ask you until we know some of
these things.

RC

"Peter Will" wrote in message
...
What would be the best forum to post a message for help about setting a
computer up with dual boot of XP and Me?


 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
dual booting x32 and x64 windowsxp George Economos Windows XP Help and Support 2 December 13th 04 06:52 PM
* Dual booting laptop - Windows XP Home + Windows 2003 Server Uncle Ben General XP issues or comments 1 December 11th 04 05:12 PM
Dual booting Confused User General XP issues or comments 3 October 25th 04 11:41 PM
Dual Booting Windows XP & Server 2003 Joe Godwin Windows XP Help and Support 1 July 29th 04 12:07 AM






All times are GMT +1. The time now is 12:13 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 PCbanter.
The comments are property of their posters.