If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
56 K modem
I have installed a pci network card , all is well, but I want to send faxes
via 56k Modem, which worked fine before.The modem does not show at all in device driver, when I start the fax wizard nothing is sent. The find installed hardware wizard comes up with a message that there is no modem on the pc. It has never been touched or removed!. I have tried everyhting so far that I know of. The problem is also that it is an old pc, old modem, the cd rom with drivers on it is only for O/S Win 95, Win 98. I have tried this. Also when it says install driver on a port it auto selects com1. I use Win XP pro. Do I buy a new modem ? Your help would be very much appreciated. |
Ads |
#2
|
|||
|
|||
56 K modem
What is the make and model of the fax mode? How did you install the fax
modem? What fax software are you proposing to use? -- Hope this helps. Gerry ~~~~~~~~~~~~~~~~~~~~~~~~ FCA Using invalid email address Stourport, Worcs, England Enquire, plan and execute. ~~~~~~~~~~~~~~~~~~~~~~~~ Please tell the newsgroup how any suggested solution worked for you. http://dts-l.org/goodpost.htm ~~~~~~~~~~~~~~~~~~~~~~~~ "H" wrote in message ... I have installed a pci network card , all is well, but I want to send faxes via 56k Modem, which worked fine before.The modem does not show at all in device driver, when I start the fax wizard nothing is sent. The find installed hardware wizard comes up with a message that there is no modem on the pc. It has never been touched or removed!. I have tried everyhting so far that I know of. The problem is also that it is an old pc, old modem, the cd rom with drivers on it is only for O/S Win 95, Win 98. I have tried this. Also when it says install driver on a port it auto selects com1. I use Win XP pro. Do I buy a new modem ? Your help would be very much appreciated. |
#3
|
|||
|
|||
56 K modem
Perhaps you disturbed the card during fitting the network card, are you sure
it is pushed in all the way or try taking it out and plugging it into a new PCI slot. Neil "H" wrote in message ... I have installed a pci network card , all is well, but I want to send faxes via 56k Modem, which worked fine before.The modem does not show at all in device driver, when I start the fax wizard nothing is sent. The find installed hardware wizard comes up with a message that there is no modem on the pc. It has never been touched or removed!. I have tried everyhting so far that I know of. The problem is also that it is an old pc, old modem, the cd rom with drivers on it is only for O/S Win 95, Win 98. I have tried this. Also when it says install driver on a port it auto selects com1. I use Win XP pro. Do I buy a new modem ? Your help would be very much appreciated. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Problem faxing with SBC DSL connection | Lolobeansmama | Printing and Faxing with Windows XP | 11 | February 16th 07 11:11 PM |
Stop Modem connection lost | Philip | General XP issues or comments | 2 | March 9th 05 05:32 PM |
Old Modem has not uninstalled properly and now new one fails | Shoff | Hardware and Windows XP | 0 | February 25th 05 05:47 PM |
Modem AND CD burning problem... | Dwi | Windows XP Help and Support | 2 | December 17th 04 10:31 AM |
Modem not installing correctly now without SP2 | Russell Allen | Windows Service Pack 2 | 4 | October 7th 04 11:58 PM |