If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Checkdisk Problem
When I run checkdisk on any drive/partition from within windows xp pro It
doesnt seem to log its findings anywhere. If I run checkdisk from outside windows from commandline and boot back into windows I can see the info in event viewer. Where does checkdisk log its info? This behaviour is on both my computers even after reformating and reinstalling. Glen |
Ads |
#2
|
|||
|
|||
Checkdisk Problem
Running chkdisk without rebooting is a waste of time. Same as CHKDSK in
read-only mode, see below. For a look at the chkdsk log. Open the Event Viewer... Start | Run | Type: eventvwr | Click OK | Look in Application | Listed as Information | Event ID: 1001 Source: Winlogon [[Description: This includes file system type; drive letter or GUID, and volume name or serial number to help determine what volume Chkdsk ran against. Also included is whether Chkdsk ran because a user scheduled it or because the dirty bit was set.]] [[When Autochk runs against a volume at boot time it records its output to a file called Bootex.log in the root of the volume being checked. The Winlogon service then moves the contents of each Bootex.log file to the Application Event log.]] [[This file states whether Chkdsk encountered any errors and, if so, whether they were fixed.]] ---- This will create a chkdsk log. Paste this into a command prompt... CHKDSK C: /F C:\CHKDISKLOG.TXT Hit your Enter key. Click YES on the popup to reboot. After CHKDSK has run paste this in Start | Run... C:\CHKDISKLOG.TXT Click OK. From: Doug Knox ----- Don't bother even running CHKDSK in read-only mode. 1. In My Computer or Windows Explorer, right-click the volume you want to check, and then click Properties. 2. On the Tools tab, click Check Now. 3. Check both boxes: o To run Chkdsk by using the /f parameter, select the Automatically fix file system errors check box, and then click Start. [[Specifies whether Windows repairs file-system errors found during disk checking. All files must be closed for this program to run. If the drive is currently in use, a message asks if you want to reschedule the disk checking for the next time you restart your computer. Your drive is not available to run other tasks while the disk is being checked.]] o To run Chkdsk by using the /r parameter, select the Scan for and attempt recovery of bad sectors check box, and then click Start. [[Specifies whether Windows repairs file-system errors found during disk checking, locates bad sectors, and recovers readable information. All files must be closed for this program to run. If the drive is currently in use, a message asks if you want to reschedule the disk checking for the next time you restart your computer. Your drive is not available to run other tasks while the disk is being checked. If you select this option, you do not need to select Automatically fix file system errors. Windows fixes any errors on the disk.]] You have to reboot for Error-checking to run. -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , Glen hunted and pecked: When I run checkdisk on any drive/partition from within windows xp pro It doesnt seem to log its findings anywhere. If I run checkdisk from outside windows from commandline and boot back into windows I can see the info in event viewer. Where does checkdisk log its info? This behaviour is on both my computers even after reformating and reinstalling. Glen |
#3
|
|||
|
|||
Checkdisk Problem
You are completely misunderstanding what I wrote. There is no log entry for
checkdisk if I run checkdisk from within windows. There are only log entries if I run checkdisk from the commandline. Glen "Wesley Vogel" wrote in message ... Running chkdisk without rebooting is a waste of time. Same as CHKDSK in read-only mode, see below. For a look at the chkdsk log. Open the Event Viewer... Start | Run | Type: eventvwr | Click OK | Look in Application | Listed as Information | Event ID: 1001 Source: Winlogon [[Description: This includes file system type; drive letter or GUID, and volume name or serial number to help determine what volume Chkdsk ran against. Also included is whether Chkdsk ran because a user scheduled it or because the dirty bit was set.]] [[When Autochk runs against a volume at boot time it records its output to a file called Bootex.log in the root of the volume being checked. The Winlogon service then moves the contents of each Bootex.log file to the Application Event log.]] [[This file states whether Chkdsk encountered any errors and, if so, whether they were fixed.]] ---- This will create a chkdsk log. Paste this into a command prompt... CHKDSK C: /F C:\CHKDISKLOG.TXT Hit your Enter key. Click YES on the popup to reboot. After CHKDSK has run paste this in Start | Run... C:\CHKDISKLOG.TXT Click OK. From: Doug Knox ----- Don't bother even running CHKDSK in read-only mode. 1. In My Computer or Windows Explorer, right-click the volume you want to check, and then click Properties. 2. On the Tools tab, click Check Now. 3. Check both boxes: o To run Chkdsk by using the /f parameter, select the Automatically fix file system errors check box, and then click Start. [[Specifies whether Windows repairs file-system errors found during disk checking. All files must be closed for this program to run. If the drive is currently in use, a message asks if you want to reschedule the disk checking for the next time you restart your computer. Your drive is not available to run other tasks while the disk is being checked.]] o To run Chkdsk by using the /r parameter, select the Scan for and attempt recovery of bad sectors check box, and then click Start. [[Specifies whether Windows repairs file-system errors found during disk checking, locates bad sectors, and recovers readable information. All files must be closed for this program to run. If the drive is currently in use, a message asks if you want to reschedule the disk checking for the next time you restart your computer. Your drive is not available to run other tasks while the disk is being checked. If you select this option, you do not need to select Automatically fix file system errors. Windows fixes any errors on the disk.]] You have to reboot for Error-checking to run. -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , Glen hunted and pecked: When I run checkdisk on any drive/partition from within windows xp pro It doesnt seem to log its findings anywhere. If I run checkdisk from outside windows from commandline and boot back into windows I can see the info in event viewer. Where does checkdisk log its info? This behaviour is on both my computers even after reformating and reinstalling. Glen |
#4
|
|||
|
|||
Checkdisk Problem
I just reread what I wrote and while I meant to say checkdisk doesnt log its
results in event viewer I didn't write it. So I'll attempt to rewrite it for clarity. There are no entries for checkdisk in event viewer if i run checkdisk from within windows. If I run checkdisk from the commandline its logged in event viewer. This behaviour is on two computers both with fresh installations of xp pro. This isn't new behaviour I have never seen a log entry for checkdisk after running it from within windows. Does your installation log is checkdisk runs if you run it within windows. I find it hard to believe both ny computers have a fault as both are new installations. Glen "Glen" wrote in message ... You are completely misunderstanding what I wrote. There is no log entry for checkdisk if I run checkdisk from within windows. There are only log entries if I run checkdisk from the commandline. Glen "Wesley Vogel" wrote in message ... Running chkdisk without rebooting is a waste of time. Same as CHKDSK in read-only mode, see below. For a look at the chkdsk log. Open the Event Viewer... Start | Run | Type: eventvwr | Click OK | Look in Application | Listed as Information | Event ID: 1001 Source: Winlogon [[Description: This includes file system type; drive letter or GUID, and volume name or serial number to help determine what volume Chkdsk ran against. Also included is whether Chkdsk ran because a user scheduled it or because the dirty bit was set.]] [[When Autochk runs against a volume at boot time it records its output to a file called Bootex.log in the root of the volume being checked. The Winlogon service then moves the contents of each Bootex.log file to the Application Event log.]] [[This file states whether Chkdsk encountered any errors and, if so, whether they were fixed.]] ---- This will create a chkdsk log. Paste this into a command prompt... CHKDSK C: /F C:\CHKDISKLOG.TXT Hit your Enter key. Click YES on the popup to reboot. After CHKDSK has run paste this in Start | Run... C:\CHKDISKLOG.TXT Click OK. From: Doug Knox ----- Don't bother even running CHKDSK in read-only mode. 1. In My Computer or Windows Explorer, right-click the volume you want to check, and then click Properties. 2. On the Tools tab, click Check Now. 3. Check both boxes: o To run Chkdsk by using the /f parameter, select the Automatically fix file system errors check box, and then click Start. [[Specifies whether Windows repairs file-system errors found during disk checking. All files must be closed for this program to run. If the drive is currently in use, a message asks if you want to reschedule the disk checking for the next time you restart your computer. Your drive is not available to run other tasks while the disk is being checked.]] o To run Chkdsk by using the /r parameter, select the Scan for and attempt recovery of bad sectors check box, and then click Start. [[Specifies whether Windows repairs file-system errors found during disk checking, locates bad sectors, and recovers readable information. All files must be closed for this program to run. If the drive is currently in use, a message asks if you want to reschedule the disk checking for the next time you restart your computer. Your drive is not available to run other tasks while the disk is being checked. If you select this option, you do not need to select Automatically fix file system errors. Windows fixes any errors on the disk.]] You have to reboot for Error-checking to run. -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , Glen hunted and pecked: When I run checkdisk on any drive/partition from within windows xp pro It doesnt seem to log its findings anywhere. If I run checkdisk from outside windows from commandline and boot back into windows I can see the info in event viewer. Where does checkdisk log its info? This behaviour is on both my computers even after reformating and reinstalling. Glen |
#5
|
|||
|
|||
Checkdisk Problem
Glen,
CHKDSK does *not* work correctly in the read-only mode. So it would be a waste of time if chkdsk logged its results in the read-only mode anyway. Running chkdsk without rebooting is a waste of time. It is the same as running chkdsk in the read-only mode. You have to reboot your machine (both of them) in order for chkdsk to work correctly. Here are some reasons... [[Chkdsk might not accurately report information in read-only mode.]] From... Chkdsk http://www.microsoft.com/resources/d...b_tol_pwfd.asp [[If you run chkdsk without the /f command-line option on an active partition, it might report spurious errors because it cannot lock the drive.]] [[Using chkdsk with open files If you specify the /f command-line option, chkdsk sends an error message if there are open files on the disk. If you do not specify the /f command-line option and open files exist, chkdsk might report lost allocation units on the disk. This could happen if open files have not yet been recorded in the file allocation table. If chkdsk reports the loss of a large number of allocation units, consider repairing the disk.]] From... Chkdsk http://www.microsoft.com/resources/d...us/chkdsk.mspx [[In read-only mode, CHKDSK quits before it completes all three phases if it encounters errors in earlier phases, and CHKDSK is prone to falsely reporting errors. For example, CHKDSK may report disk corruption if NTFS happens to modify areas of a disk while CHKDSK is examining the disk. For correct verification, a volume must be static, and the only way to guarantee a static state is to lock the volume. CHKDSK locks the volume only if you specify the /F switch (or the /R switch, which implies /F). You may need to run CHKDSK more than once to get CHKDSK to complete all its passes in read-only mode. ]] From... An Explanation of the New C and I Switches That Are Available to Use with Chkdsk.exe http://support.microsoft.com/default...b;en-us;314835 To take advantage of all the Chkdsk parameters, use the command-line version of Chkdsk. Describes how to use the chkdsk command at the command line. http://www.microsoft.com/windowsxp/h.../en/chkdsk.asp -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , Glen hunted and pecked: I just reread what I wrote and while I meant to say checkdisk doesnt log its results in event viewer I didn't write it. So I'll attempt to rewrite it for clarity. There are no entries for checkdisk in event viewer if i run checkdisk from within windows. If I run checkdisk from the commandline its logged in event viewer. This behaviour is on two computers both with fresh installations of xp pro. This isn't new behaviour I have never seen a log entry for checkdisk after running it from within windows. Does your installation log is checkdisk runs if you run it within windows. I find it hard to believe both ny computers have a fault as both are new installations. Glen "Glen" wrote in message ... You are completely misunderstanding what I wrote. There is no log entry for checkdisk if I run checkdisk from within windows. There are only log entries if I run checkdisk from the commandline. Glen "Wesley Vogel" wrote in message ... Running chkdisk without rebooting is a waste of time. Same as CHKDSK in read-only mode, see below. For a look at the chkdsk log. Open the Event Viewer... Start | Run | Type: eventvwr | Click OK | Look in Application | Listed as Information | Event ID: 1001 Source: Winlogon [[Description: This includes file system type; drive letter or GUID, and volume name or serial number to help determine what volume Chkdsk ran against. Also included is whether Chkdsk ran because a user scheduled it or because the dirty bit was set.]] [[When Autochk runs against a volume at boot time it records its output to a file called Bootex.log in the root of the volume being checked. The Winlogon service then moves the contents of each Bootex.log file to the Application Event log.]] [[This file states whether Chkdsk encountered any errors and, if so, whether they were fixed.]] ---- This will create a chkdsk log. Paste this into a command prompt... CHKDSK C: /F C:\CHKDISKLOG.TXT Hit your Enter key. Click YES on the popup to reboot. After CHKDSK has run paste this in Start | Run... C:\CHKDISKLOG.TXT Click OK. From: Doug Knox ----- Don't bother even running CHKDSK in read-only mode. 1. In My Computer or Windows Explorer, right-click the volume you want to check, and then click Properties. 2. On the Tools tab, click Check Now. 3. Check both boxes: o To run Chkdsk by using the /f parameter, select the Automatically fix file system errors check box, and then click Start. [[Specifies whether Windows repairs file-system errors found during disk checking. All files must be closed for this program to run. If the drive is currently in use, a message asks if you want to reschedule the disk checking for the next time you restart your computer. Your drive is not available to run other tasks while the disk is being checked.]] o To run Chkdsk by using the /r parameter, select the Scan for and attempt recovery of bad sectors check box, and then click Start. [[Specifies whether Windows repairs file-system errors found during disk checking, locates bad sectors, and recovers readable information. All files must be closed for this program to run. If the drive is currently in use, a message asks if you want to reschedule the disk checking for the next time you restart your computer. Your drive is not available to run other tasks while the disk is being checked. If you select this option, you do not need to select Automatically fix file system errors. Windows fixes any errors on the disk.]] You have to reboot for Error-checking to run. -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , Glen hunted and pecked: When I run checkdisk on any drive/partition from within windows xp pro It doesnt seem to log its findings anywhere. If I run checkdisk from outside windows from commandline and boot back into windows I can see the info in event viewer. Where does checkdisk log its info? This behaviour is on both my computers even after reformating and reinstalling. Glen |
#6
|
|||
|
|||
Checkdisk Problem
Even when I run it checking automatically fix file system errors and scan
for bad sectors it still doesn't log the results. I have a hard drive that has some bad sectors but has no data on at the moment and to monitor the ongoing state of the drive I need to run checkdisk and see the results. I could always reboot and do it from the command line but its a pain when windows should log its findings. Glen "Wesley Vogel" wrote in message ... Glen, CHKDSK does *not* work correctly in the read-only mode. So it would be a waste of time if chkdsk logged its results in the read-only mode anyway. Running chkdsk without rebooting is a waste of time. It is the same as running chkdsk in the read-only mode. You have to reboot your machine (both of them) in order for chkdsk to work correctly. Here are some reasons... [[Chkdsk might not accurately report information in read-only mode.]] From... Chkdsk http://www.microsoft.com/resources/d...b_tol_pwfd.asp [[If you run chkdsk without the /f command-line option on an active partition, it might report spurious errors because it cannot lock the drive.]] [[Using chkdsk with open files If you specify the /f command-line option, chkdsk sends an error message if there are open files on the disk. If you do not specify the /f command-line option and open files exist, chkdsk might report lost allocation units on the disk. This could happen if open files have not yet been recorded in the file allocation table. If chkdsk reports the loss of a large number of allocation units, consider repairing the disk.]] From... Chkdsk http://www.microsoft.com/resources/d...us/chkdsk.mspx [[In read-only mode, CHKDSK quits before it completes all three phases if it encounters errors in earlier phases, and CHKDSK is prone to falsely reporting errors. For example, CHKDSK may report disk corruption if NTFS happens to modify areas of a disk while CHKDSK is examining the disk. For correct verification, a volume must be static, and the only way to guarantee a static state is to lock the volume. CHKDSK locks the volume only if you specify the /F switch (or the /R switch, which implies /F). You may need to run CHKDSK more than once to get CHKDSK to complete all its passes in read-only mode. ]] From... An Explanation of the New C and I Switches That Are Available to Use with Chkdsk.exe http://support.microsoft.com/default...b;en-us;314835 To take advantage of all the Chkdsk parameters, use the command-line version of Chkdsk. Describes how to use the chkdsk command at the command line. http://www.microsoft.com/windowsxp/h.../en/chkdsk.asp -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , Glen hunted and pecked: I just reread what I wrote and while I meant to say checkdisk doesnt log its results in event viewer I didn't write it. So I'll attempt to rewrite it for clarity. There are no entries for checkdisk in event viewer if i run checkdisk from within windows. If I run checkdisk from the commandline its logged in event viewer. This behaviour is on two computers both with fresh installations of xp pro. This isn't new behaviour I have never seen a log entry for checkdisk after running it from within windows. Does your installation log is checkdisk runs if you run it within windows. I find it hard to believe both ny computers have a fault as both are new installations. Glen "Glen" wrote in message ... You are completely misunderstanding what I wrote. There is no log entry for checkdisk if I run checkdisk from within windows. There are only log entries if I run checkdisk from the commandline. Glen "Wesley Vogel" wrote in message ... Running chkdisk without rebooting is a waste of time. Same as CHKDSK in read-only mode, see below. For a look at the chkdsk log. Open the Event Viewer... Start | Run | Type: eventvwr | Click OK | Look in Application | Listed as Information | Event ID: 1001 Source: Winlogon [[Description: This includes file system type; drive letter or GUID, and volume name or serial number to help determine what volume Chkdsk ran against. Also included is whether Chkdsk ran because a user scheduled it or because the dirty bit was set.]] [[When Autochk runs against a volume at boot time it records its output to a file called Bootex.log in the root of the volume being checked. The Winlogon service then moves the contents of each Bootex.log file to the Application Event log.]] [[This file states whether Chkdsk encountered any errors and, if so, whether they were fixed.]] ---- This will create a chkdsk log. Paste this into a command prompt... CHKDSK C: /F C:\CHKDISKLOG.TXT Hit your Enter key. Click YES on the popup to reboot. After CHKDSK has run paste this in Start | Run... C:\CHKDISKLOG.TXT Click OK. From: Doug Knox ----- Don't bother even running CHKDSK in read-only mode. 1. In My Computer or Windows Explorer, right-click the volume you want to check, and then click Properties. 2. On the Tools tab, click Check Now. 3. Check both boxes: o To run Chkdsk by using the /f parameter, select the Automatically fix file system errors check box, and then click Start. [[Specifies whether Windows repairs file-system errors found during disk checking. All files must be closed for this program to run. If the drive is currently in use, a message asks if you want to reschedule the disk checking for the next time you restart your computer. Your drive is not available to run other tasks while the disk is being checked.]] o To run Chkdsk by using the /r parameter, select the Scan for and attempt recovery of bad sectors check box, and then click Start. [[Specifies whether Windows repairs file-system errors found during disk checking, locates bad sectors, and recovers readable information. All files must be closed for this program to run. If the drive is currently in use, a message asks if you want to reschedule the disk checking for the next time you restart your computer. Your drive is not available to run other tasks while the disk is being checked. If you select this option, you do not need to select Automatically fix file system errors. Windows fixes any errors on the disk.]] You have to reboot for Error-checking to run. -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , Glen hunted and pecked: When I run checkdisk on any drive/partition from within windows xp pro It doesnt seem to log its findings anywhere. If I run checkdisk from outside windows from commandline and boot back into windows I can see the info in event viewer. Where does checkdisk log its info? This behaviour is on both my computers even after reformating and reinstalling. Glen |
#7
|
|||
|
|||
Checkdisk Problem
Glen,
One of us is missing something here. Every time chkdsk runs a Bootex.log is created. The info from Bootex.log is usually sent to the Event Viewer and then the Bootex.log is deleted. Bootex.log can be accessed with recovery software such as Restoration. This is free. Restoration Version 2.5.14 Author: Brian Kato http://www3.telus.net/mikebike/RESTORATION.html See if for some reason you still have a Bootex.log on your machine and maybe it's corrupted. c:\bootex.log or whateverdrive:\bootex.log If you have a corrupted bootex.log and cannot delete it you may have to run chkdsk /r Or you may have to run chkdsk from the Recovery Console. http://www.annoyances.org/exec/forum/winxp/1080019958 -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , Glen hunted and pecked: Even when I run it checking automatically fix file system errors and scan for bad sectors it still doesn't log the results. I have a hard drive that has some bad sectors but has no data on at the moment and to monitor the ongoing state of the drive I need to run checkdisk and see the results. I could always reboot and do it from the command line but its a pain when windows should log its findings. Glen "Wesley Vogel" wrote in message ... Glen, CHKDSK does *not* work correctly in the read-only mode. So it would be a waste of time if chkdsk logged its results in the read-only mode anyway. Running chkdsk without rebooting is a waste of time. It is the same as running chkdsk in the read-only mode. You have to reboot your machine (both of them) in order for chkdsk to work correctly. Here are some reasons... [[Chkdsk might not accurately report information in read-only mode.]] From... Chkdsk http://www.microsoft.com/resources/d...b_tol_pwfd.asp [[If you run chkdsk without the /f command-line option on an active partition, it might report spurious errors because it cannot lock the drive.]] [[Using chkdsk with open files If you specify the /f command-line option, chkdsk sends an error message if there are open files on the disk. If you do not specify the /f command-line option and open files exist, chkdsk might report lost allocation units on the disk. This could happen if open files have not yet been recorded in the file allocation table. If chkdsk reports the loss of a large number of allocation units, consider repairing the disk.]] From... Chkdsk http://www.microsoft.com/resources/d...us/chkdsk.mspx [[In read-only mode, CHKDSK quits before it completes all three phases if it encounters errors in earlier phases, and CHKDSK is prone to falsely reporting errors. For example, CHKDSK may report disk corruption if NTFS happens to modify areas of a disk while CHKDSK is examining the disk. For correct verification, a volume must be static, and the only way to guarantee a static state is to lock the volume. CHKDSK locks the volume only if you specify the /F switch (or the /R switch, which implies /F). You may need to run CHKDSK more than once to get CHKDSK to complete all its passes in read-only mode. ]] From... An Explanation of the New C and I Switches That Are Available to Use with Chkdsk.exe http://support.microsoft.com/default...b;en-us;314835 To take advantage of all the Chkdsk parameters, use the command-line version of Chkdsk. Describes how to use the chkdsk command at the command line. http://www.microsoft.com/windowsxp/h.../en/chkdsk.asp -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , Glen hunted and pecked: I just reread what I wrote and while I meant to say checkdisk doesnt log its results in event viewer I didn't write it. So I'll attempt to rewrite it for clarity. There are no entries for checkdisk in event viewer if i run checkdisk from within windows. If I run checkdisk from the commandline its logged in event viewer. This behaviour is on two computers both with fresh installations of xp pro. This isn't new behaviour I have never seen a log entry for checkdisk after running it from within windows. Does your installation log is checkdisk runs if you run it within windows. I find it hard to believe both ny computers have a fault as both are new installations. Glen "Glen" wrote in message ... You are completely misunderstanding what I wrote. There is no log entry for checkdisk if I run checkdisk from within windows. There are only log entries if I run checkdisk from the commandline. Glen "Wesley Vogel" wrote in message ... Running chkdisk without rebooting is a waste of time. Same as CHKDSK in read-only mode, see below. For a look at the chkdsk log. Open the Event Viewer... Start | Run | Type: eventvwr | Click OK | Look in Application | Listed as Information | Event ID: 1001 Source: Winlogon [[Description: This includes file system type; drive letter or GUID, and volume name or serial number to help determine what volume Chkdsk ran against. Also included is whether Chkdsk ran because a user scheduled it or because the dirty bit was set.]] [[When Autochk runs against a volume at boot time it records its output to a file called Bootex.log in the root of the volume being checked. The Winlogon service then moves the contents of each Bootex.log file to the Application Event log.]] [[This file states whether Chkdsk encountered any errors and, if so, whether they were fixed.]] ---- This will create a chkdsk log. Paste this into a command prompt... CHKDSK C: /F C:\CHKDISKLOG.TXT Hit your Enter key. Click YES on the popup to reboot. After CHKDSK has run paste this in Start | Run... C:\CHKDISKLOG.TXT Click OK. From: Doug Knox ----- Don't bother even running CHKDSK in read-only mode. 1. In My Computer or Windows Explorer, right-click the volume you want to check, and then click Properties. 2. On the Tools tab, click Check Now. 3. Check both boxes: o To run Chkdsk by using the /f parameter, select the Automatically fix file system errors check box, and then click Start. [[Specifies whether Windows repairs file-system errors found during disk checking. All files must be closed for this program to run. If the drive is currently in use, a message asks if you want to reschedule the disk checking for the next time you restart your computer. Your drive is not available to run other tasks while the disk is being checked.]] o To run Chkdsk by using the /r parameter, select the Scan for and attempt recovery of bad sectors check box, and then click Start. [[Specifies whether Windows repairs file-system errors found during disk checking, locates bad sectors, and recovers readable information. All files must be closed for this program to run. If the drive is currently in use, a message asks if you want to reschedule the disk checking for the next time you restart your computer. Your drive is not available to run other tasks while the disk is being checked. If you select this option, you do not need to select Automatically fix file system errors. Windows fixes any errors on the disk.]] You have to reboot for Error-checking to run. -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , Glen hunted and pecked: When I run checkdisk on any drive/partition from within windows xp pro It doesnt seem to log its findings anywhere. If I run checkdisk from outside windows from commandline and boot back into windows I can see the info in event viewer. Where does checkdisk log its info? This behaviour is on both my computers even after reformating and reinstalling. Glen |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
printing problems | LISA | Printing and Faxing with Windows XP | 28 | September 23rd 06 07:29 PM |
checkdisk - problem | Karsten Kirchner | The Basics | 2 | November 30th 05 10:58 PM |
Problem faced after connect to internet. | E-RO-SEN-NIN | New Users to Windows XP | 2 | June 12th 05 03:00 AM |
||OT||: MSTS vs PFN | Jim | General XP issues or comments | 0 | April 19th 05 10:39 PM |
Computer Problem Report | Treeman | General XP issues or comments | 0 | April 19th 05 04:16 PM |