If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Program Un install help See inside
I'm not familiar with the "reregister", but I would suggest you contact
Acronis directly, since this group is for Windows XP. To contact Acronis (free) technical support: http://www.wilderssecurity.com/forumdisplay.php?f=74 Modem Ani "GreyTop" wrote in message ... I have Acronis popup blocker installed on my machine and I would like to un install it. The problem when I use the un installer it leaves the following entry in the reregister. RunDll32.exe C:\PROGRA~1\Acronis\PRIVAC~1\Blocker.dll,Run I have deleted this but it immediately returns when I close the registry. Then on reboot I get the error File not found. I tried disabling the item in the program properties as well as not to load on start, but it seems to have a mind of it's own. I suppose the item is failing to un register but I don't know. Any help please to get rid of this problem. |
Ads |
#2
|
|||
|
|||
In ,
Modem Ani had this to say: My reply is at the bottom of your sent message: I'm not familiar with the "reregister", but I would suggest you contact Acronis directly, since this group is for Windows XP. To contact Acronis (free) technical support: http://www.wilderssecurity.com/forumdisplay.php?f=74 Modem Ani And if that doesn't work, strange as this sounds, install it again and then uninstall it. I know, it sounds strange, but it has been known to work. Galen -- Signature changed for a moment of silence. Rest well Alex and we'll see you on the other side. |
#3
|
|||
|
|||
I think the point was to re-install it and then uninstall it again to see if
that helps. There are 3 places/ways that can run a program at startup: the registry, as a service, and the startup folder. The preferences of the program itself is a good place to disable it. Look in your services panel (Start Run services.msc) for a service related to your program. If it's there, disable it. It may also be starting in the run key: HKLM\Software\Microsoft\Windows\CurrentVersion\Run or the RunOnce key: HKLM\Software\Microsoft\Windows\CurrentVersion\Run Once Remember that making changes to the registry can be dangerous, so backup before you edit and edit with extreme caution! "GreyTop" wrote: On Wed, 20 Apr 2005 14:24:29 -0400, "Galen" wrote: In , Modem Ani had this to say: My reply is at the bottom of your sent message: I'm not familiar with the "reregister", but I would suggest you contact Acronis directly, since this group is for Windows XP. To contact Acronis (free) technical support: http://www.wilderssecurity.com/forumdisplay.php?f=74 Modem Ani And if that doesn't work, strange as this sounds, install it again and then uninstall it. I know, it sounds strange, but it has been known to work. Galen I reinstalled and the program works but I have it disabled in the program and set to NOT load on start. It still loads anyway. I am at my wits end on this one. It has not been addressed in the forum only mentioned in one place and that did not get any replies. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
System Infiltrated >>Program start up group changes . Please See l | Steve needs help | Windows XP Help and Support | 2 | March 19th 05 11:19 PM |
Help unable to install any program | Jul | Windows XP Help and Support | 4 | February 26th 05 10:10 PM |
install program twice on same computer | Brent | General XP issues or comments | 3 | October 12th 04 02:34 AM |
Application program doesn't work after install Windows XP SP2 | Snow | Windows Service Pack 2 | 3 | September 17th 04 11:03 PM |
Program will not run after sp2 install | ualjetmech | Windows Service Pack 2 | 1 | September 15th 04 07:15 AM |