A Windows XP help forum. PCbanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » PCbanter forum » Microsoft Windows XP » Hardware and Windows XP
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

+12 VOLT Indicator on Winbond Hardware Doctor



 
 
Thread Tools Display Modes
  #1  
Old December 5th 04, 02:09 AM
Ted
external usenet poster
 
Posts: n/a
Default +12 VOLT Indicator on Winbond Hardware Doctor

Hi All

I recently have been having trouble with Winbond Hardware doctor. I am
running Athlon XP 2800+ Lanparty MB with Windows XP Pro.My Winbond keeps
setting off an alarm saying that the minimum voltage level has been met. The
volts section starts at +12V. The high level indicator is set for 13.00 and
the low kevel indicator is set for 11.00. My system seems to be jumping below
this level constantly and the motherboard alarm briefly sounds. Would anyone
know possible causes of this. Could it be something to do with my PSU. It is
a 12V 360 Watt chieftec. Currently, and since day 1 I have a DVD Writer - CD
Writer, Additional USB front ports, Creative sound system with creative sound
card, Wireless access point, 256mb graphics card, 512mb DDR.

Any help on this is much appreciated.


Ads
  #2  
Old December 5th 04, 02:23 AM
Gary
external usenet poster
 
Posts: n/a
Default +12 VOLT Indicator on Winbond Hardware Doctor

IF the other voltages like 3.3, 5V, -12V are jumping around the same time,
then your PSU is on the way out.

Check if you get the same voltage errors in your BIOS.

If it's just the +12V supply going down possible to be:

1. HDD on the way out, the motor is stalling, causing a larger demand on the
PSU.
2. Other peripheral, floppy, CD. keyboard, mouse etc is starting to fault.
Unplug each one and see if that cures the problem. Remove the power from the
PC before you do, k? don't just switch the PC off, remove the power cable
right out then remove each device and check the voltages again.
3. Poor connectors - Check that all 4 pins are mated properly. The pins can
sometimes come away even though the rest of the connectors are fine.
4. Just too much load - How many HDD's do you have?
5. Motherboard mounting screws, perhaps one is shorting out to the chassis
and shouldn't. Or one is loose.


"Ted" wrote in message
...
Hi All

I recently have been having trouble with Winbond Hardware doctor. I am
running Athlon XP 2800+ Lanparty MB with Windows XP Pro.My Winbond keeps
setting off an alarm saying that the minimum voltage level has been met.

The
volts section starts at +12V. The high level indicator is set for 13.00

and
the low kevel indicator is set for 11.00. My system seems to be jumping

below
this level constantly and the motherboard alarm briefly sounds. Would

anyone
know possible causes of this. Could it be something to do with my PSU. It

is
a 12V 360 Watt chieftec. Currently, and since day 1 I have a DVD Writer -

CD
Writer, Additional USB front ports, Creative sound system with creative

sound
card, Wireless access point, 256mb graphics card, 512mb DDR.

Any help on this is much appreciated.




  #3  
Old December 5th 04, 06:57 AM
w_tom
external usenet poster
 
Posts: n/a
Default +12 VOLT Indicator on Winbond Hardware Doctor

Voltages measured by BIOS are not accurate. Either confirm
those voltage readings with a 3.5 digit multimeter, OR
calibrate the BIOS meter with a 3.5 digit meter.

The power supply should be more than sufficient. But the
devil is in the details. A power supply with more than enough
overall wattage may provide insufficient current on one
voltage output. Again, this is why multimeter is required.

Ted wrote:
I recently have been having trouble with Winbond Hardware doctor. I am
running Athlon XP 2800+ Lanparty MB with Windows XP Pro.My Winbond keeps
setting off an alarm saying that the minimum voltage level has been met.
The volts section starts at +12V. The high level indicator is set for
13.00 and the low kevel indicator is set for 11.00. My system seems to
be jumping below this level constantly and the motherboard alarm briefly
sounds. Would anyone know possible causes of this. Could it be something
to do with my PSU. It is a 12V 360 Watt chieftec. Currently, and since
day 1 I have a DVD Writer - CD Writer, Additional USB front ports,
Creative sound system with creative sound card, Wireless access point,
256mb graphics card, 512mb DDR.

Any help on this is much appreciated.

  #4  
Old December 5th 04, 10:09 AM
Gary
external usenet poster
 
Posts: n/a
Default +12 VOLT Indicator on Winbond Hardware Doctor

How far out is the BIOS reading from the real reading?
50% + ? Please advise.

"w_tom" wrote in message
...
Voltages measured by BIOS are not accurate. Either confirm
those voltage readings with a 3.5 digit multimeter, OR
calibrate the BIOS meter with a 3.5 digit meter.

The power supply should be more than sufficient. But the
devil is in the details. A power supply with more than enough
overall wattage may provide insufficient current on one
voltage output. Again, this is why multimeter is required.



  #5  
Old December 5th 04, 06:57 PM
Ted
external usenet poster
 
Posts: n/a
Default +12 VOLT Indicator on Winbond Hardware Doctor

Hi Guys

Thanks for getting back to me. I don't have a metre to measure but I did try
and remove the other devices to see the difference, but there was none. The
HDD and CD + DVD drive have been replaced within the last 2 weeks. This was
happening before then. The readings in the BIOS are simalar to the Hadware
Doctor. I currently only have 1 HDD attached which is a 160gb SATA 8MB cache,
I also would like to attach another in the future but am i right in saying
thats out of the question?? or should I look at a new PSU. They readings are
as follows.

LL = Low Limit - HL= High Limit
+3.3V..... LL3.00 - HL3.50. This reading jumps between 3.34 & 3.36

+5V .....LL4.50 - HL 5.50. Steady @ 5.11

+12V.....LL11.00 - HL 13.00. This jumps between 11.04 & 10.50, quiet a
difference and not meeting the 12V.

-12V.....LL -14.00 - HL -11.0. This jumps between -11.78 & -11.86

again thanks for your help

Ted





"Gary" wrote:

How far out is the BIOS reading from the real reading?
50% + ? Please advise.

"w_tom" wrote in message
...
Voltages measured by BIOS are not accurate. Either confirm
those voltage readings with a 3.5 digit multimeter, OR
calibrate the BIOS meter with a 3.5 digit meter.

The power supply should be more than sufficient. But the
devil is in the details. A power supply with more than enough
overall wattage may provide insufficient current on one
voltage output. Again, this is why multimeter is required.




  #6  
Old December 6th 04, 02:24 AM
w_tom
external usenet poster
 
Posts: n/a
Default +12 VOLT Indicator on Winbond Hardware Doctor

Obtain that meter even in a screw driver store. Meter is as
essential as a screw driver. So ubiquitous as to be sold even
in Home Depot, Sears, and Lowes. So inexpensive that it is
now a standard tool.

BIOS measurement circuits can vary significantly. How
accurate are they? An honest computer provider or motherboard
manufactuer provides that numerical specification. However a
'motherboard voltmeter' must be accurate enough duplicate the
accuracy of a 3.5 digit multimeter. See spec limits in
previous posts. Voltages must reside in the upper 3/4s of
those limits. Anything else can mean strange and intermittent
failures. If the meter is less accurate, then the voltage
readings must lie even further inside those limits.

Limits provided below are too wide. For example, upper
limit is 12.6. Below, that same limit is 13 volts - too
high. A voltage below 4.85 is too low. And yet limits below
are 4.5 - too low.

Don't screw around. Don't waste good money and time by
shotgunning - scam that an auto mechanic does when he does
not have basic knowledge. Get the meter to confirm an
essential component - the PSU. Then move on to other 'usual'
suspects using standard information sources such as system
(event) log, Device Manager, and comprehensive diagnostics
provided free by any reponsible computer manufacturer.

Ted wrote:
Hi Guys
Thanks for getting back to me. I don't have a metre to measure but
I did try and remove the other devices to see the difference, but
there was none. The HDD and CD + DVD drive have been replaced within
the last 2 weeks. This was happening before then. The readings in
the BIOS are simalar to the Hadware Doctor. I currently only have 1
HDD attached which is a 160gb SATA 8MB cache, I also would like to
attach another in the future but am i right in saying thats out of
the question?? or should I look at a new PSU. They readings are
as follows.

LL = Low Limit - HL= High Limit
+3.3V..... LL3.00 - HL3.50. This reading jumps between 3.34 & 3.36

+5V .....LL4.50 - HL 5.50. Steady @ 5.11

+12V.....LL11.00 - HL 13.00. This jumps between 11.04 & 10.50, quiet a
difference and not meeting the 12V.

-12V.....LL -14.00 - HL -11.0. This jumps between -11.78 & -11.86

again thanks for your help

Ted

"Gary" wrote:

How far out is the BIOS reading from the real reading?
50% + ? Please advise.

  #7  
Old December 8th 04, 02:15 AM
Ted
external usenet poster
 
Posts: n/a
Default +12 VOLT Indicator on Winbond Hardware Doctor

Hi,

I have a friend that has let me borrow a PSU, when I check Winbond hardware
Doctor with the new PSU, instead of the alarm sounding now and then, it's on
constant.

Does that make any more sense? Im so confused???

"w_tom" wrote:

Obtain that meter even in a screw driver store. Meter is as
essential as a screw driver. So ubiquitous as to be sold even
in Home Depot, Sears, and Lowes. So inexpensive that it is
now a standard tool.

BIOS measurement circuits can vary significantly. How
accurate are they? An honest computer provider or motherboard
manufactuer provides that numerical specification. However a
'motherboard voltmeter' must be accurate enough duplicate the
accuracy of a 3.5 digit multimeter. See spec limits in
previous posts. Voltages must reside in the upper 3/4s of
those limits. Anything else can mean strange and intermittent
failures. If the meter is less accurate, then the voltage
readings must lie even further inside those limits.

Limits provided below are too wide. For example, upper
limit is 12.6. Below, that same limit is 13 volts - too
high. A voltage below 4.85 is too low. And yet limits below
are 4.5 - too low.

Don't screw around. Don't waste good money and time by
shotgunning - scam that an auto mechanic does when he does
not have basic knowledge. Get the meter to confirm an
essential component - the PSU. Then move on to other 'usual'
suspects using standard information sources such as system
(event) log, Device Manager, and comprehensive diagnostics
provided free by any reponsible computer manufacturer.

Ted wrote:
Hi Guys
Thanks for getting back to me. I don't have a metre to measure but
I did try and remove the other devices to see the difference, but
there was none. The HDD and CD + DVD drive have been replaced within
the last 2 weeks. This was happening before then. The readings in
the BIOS are simalar to the Hadware Doctor. I currently only have 1
HDD attached which is a 160gb SATA 8MB cache, I also would like to
attach another in the future but am i right in saying thats out of
the question?? or should I look at a new PSU. They readings are
as follows.

LL = Low Limit - HL= High Limit
+3.3V..... LL3.00 - HL3.50. This reading jumps between 3.34 & 3.36

+5V .....LL4.50 - HL 5.50. Steady @ 5.11

+12V.....LL11.00 - HL 13.00. This jumps between 11.04 & 10.50, quiet a
difference and not meeting the 12V.

-12V.....LL -14.00 - HL -11.0. This jumps between -11.78 & -11.86

again thanks for your help

Ted

"Gary" wrote:

How far out is the BIOS reading from the real reading?
50% + ? Please advise.


  #8  
Old December 8th 04, 06:23 AM
w_tom
external usenet poster
 
Posts: n/a
Default +12 VOLT Indicator on Winbond Hardware Doctor

That 'swap PSU' test only implies that something else is
wrong. However assumed (and not stated): is the new PSU
exactly same? In the meantime, numbers are necessary to
provide useful assistance. Considering all the work and all
the added risk to both your system and his PSU, it makes more
sense (and saves significant time) to first take those voltage
readings.

Those upper and lower limits are significantly outside of
acceptable voltages. If you are getting alarms with limits
that far too wide, then surprising the computer is still
working. Winbond voltage readings are only as accurate as
hardware on motherboard. Use the meter so we know what your
system is really doing. Doing anything else will only make
you and us more confused. Those multimeter numbers are
essential. Without them, your responses will only be wild
speculation.

BTW what did those other information sources (Device
Manager, system log, etc) report? Worry more about getting
every piece of information requested. Being confused should
have come much later.

Ted wrote:
I have a friend that has let me borrow a PSU, when I check Winbond
hardware Doctor with the new PSU, instead of the alarm sounding now
and then, it's on constant.

Does that make any more sense? Im so confused???

"w_tom" wrote:
Obtain that meter even in a screw driver store. Meter is as
essential as a screw driver. So ubiquitous as to be sold even
in Home Depot, Sears, and Lowes. So inexpensive that it is
now a standard tool.

BIOS measurement circuits can vary significantly. How
accurate are they? An honest computer provider or motherboard
manufactuer provides that numerical specification. However a
'motherboard voltmeter' must be accurate enough duplicate the
accuracy of a 3.5 digit multimeter. See spec limits in
previous posts. Voltages must reside in the upper 3/4s of
those limits. Anything else can mean strange and intermittent
failures. If the meter is less accurate, then the voltage
readings must lie even further inside those limits.

Limits provided below are too wide. For example, upper
limit is 12.6. Below, that same limit is 13 volts - too
high. A voltage below 4.85 is too low. And yet limits below
are 4.5 - too low.

Don't screw around. Don't waste good money and time by
shotgunning - scam that an auto mechanic does when he does
not have basic knowledge. Get the meter to confirm an
essential component - the PSU. Then move on to other 'usual'
suspects using standard information sources such as system
(event) log, Device Manager, and comprehensive diagnostics
provided free by any reponsible computer manufacturer.

  #9  
Old December 10th 04, 12:21 AM
Ted
external usenet poster
 
Posts: n/a
Default +12 VOLT Indicator on Winbond Hardware Doctor

No, the PSU is a 450 Watt, I know what you mean, I should be getting the
correct details instead of wild guessing. I will buy a metre on Saturday as I
work shifts. I am not sure how to use a metre or where I should be putting it
to test, sorry if I sound stupid!! But you've gotta start somewhere. Help
with this is much appreciated.

"w_tom" wrote:

That 'swap PSU' test only implies that something else is
wrong. However assumed (and not stated): is the new PSU
exactly same? In the meantime, numbers are necessary to
provide useful assistance. Considering all the work and all
the added risk to both your system and his PSU, it makes more
sense (and saves significant time) to first take those voltage
readings.

Those upper and lower limits are significantly outside of
acceptable voltages. If you are getting alarms with limits
that far too wide, then surprising the computer is still
working. Winbond voltage readings are only as accurate as
hardware on motherboard. Use the meter so we know what your
system is really doing. Doing anything else will only make
you and us more confused. Those multimeter numbers are
essential. Without them, your responses will only be wild
speculation.

BTW what did those other information sources (Device
Manager, system log, etc) report? Worry more about getting
every piece of information requested. Being confused should
have come much later.

Ted wrote:
I have a friend that has let me borrow a PSU, when I check Winbond
hardware Doctor with the new PSU, instead of the alarm sounding now
and then, it's on constant.

Does that make any more sense? Im so confused???

"w_tom" wrote:
Obtain that meter even in a screw driver store. Meter is as
essential as a screw driver. So ubiquitous as to be sold even
in Home Depot, Sears, and Lowes. So inexpensive that it is
now a standard tool.

BIOS measurement circuits can vary significantly. How
accurate are they? An honest computer provider or motherboard
manufactuer provides that numerical specification. However a
'motherboard voltmeter' must be accurate enough duplicate the
accuracy of a 3.5 digit multimeter. See spec limits in
previous posts. Voltages must reside in the upper 3/4s of
those limits. Anything else can mean strange and intermittent
failures. If the meter is less accurate, then the voltage
readings must lie even further inside those limits.

Limits provided below are too wide. For example, upper
limit is 12.6. Below, that same limit is 13 volts - too
high. A voltage below 4.85 is too low. And yet limits below
are 4.5 - too low.

Don't screw around. Don't waste good money and time by
shotgunning - scam that an auto mechanic does when he does
not have basic knowledge. Get the meter to confirm an
essential component - the PSU. Then move on to other 'usual'
suspects using standard information sources such as system
(event) log, Device Manager, and comprehensive diagnostics
provided free by any reponsible computer manufacturer.


  #10  
Old December 10th 04, 01:52 AM
w_tom
external usenet poster
 
Posts: n/a
Default +12 VOLT Indicator on Winbond Hardware Doctor

Meter has two leads. All voltages are 'electrical pressure'
between two points. The previously posted procedures describe
measuring voltage between two colored wires. IOW black lead
touches PSU black wire (inside white nylon connector where it
connects to motherboard). Red wire touches PSU's red, yellow,
orange, green etc wires to measure voltage on that wire. Just
set voltmeter selector to DC volts, touch probes, and read
numbers on meter. Record voltage for each colored wire. Then
compare to voltages on chart. 3.3, 5, and 12 volt wires
should read in upper 3/4s of limits.

Sidebar: Many 450 watt power supplies do not even output
their rated power. Just another problem with so many power
supplies dumped into America that don't even meet Intel
specs. This web site demonstrates a problem too common with
imported power supplies:
http://www6.tomshardware.com/howto/0...021/index.html

http://www6.tomshardware.com/howto/0...pplies-15.html
Time and time again, our lab measurements were unable to verify
the output figures represented on the model identification
sticker.



Ted wrote:
No, the PSU is a 450 Watt, I know what you mean, I should be getting
the correct details instead of wild guessing. I will buy a metre on
Saturday as I work shifts. I am not sure how to use a metre or where
I should be putting it to test, sorry if I sound stupid!! But you've
gotta start somewhere. Help with this is much appreciated.

"w_tom" wrote:

That 'swap PSU' test only implies that something else is
wrong. However assumed (and not stated): is the new PSU
exactly same? In the meantime, numbers are necessary to
provide useful assistance. Considering all the work and all
the added risk to both your system and his PSU, it makes more
sense (and saves significant time) to first take those voltage
readings.

Those upper and lower limits are significantly outside of
acceptable voltages. If you are getting alarms with limits
that far too wide, then surprising the computer is still
working. Winbond voltage readings are only as accurate as
hardware on motherboard. Use the meter so we know what your
system is really doing. Doing anything else will only make
you and us more confused. Those multimeter numbers are
essential. Without them, your responses will only be wild
speculation.

BTW what did those other information sources (Device
Manager, system log, etc) report? Worry more about getting
every piece of information requested. Being confused should
have come much later.

Ted wrote:
I have a friend that has let me borrow a PSU, when I check Winbond
hardware Doctor with the new PSU, instead of the alarm sounding now
and then, it's on constant.

Does that make any more sense? Im so confused???

"w_tom" wrote:
Obtain that meter even in a screw driver store. Meter is as
essential as a screw driver. So ubiquitous as to be sold even
in Home Depot, Sears, and Lowes. So inexpensive that it is
now a standard tool.

BIOS measurement circuits can vary significantly. How
accurate are they? An honest computer provider or motherboard
manufactuer provides that numerical specification. However a
'motherboard voltmeter' must be accurate enough duplicate the
accuracy of a 3.5 digit multimeter. See spec limits in
previous posts. Voltages must reside in the upper 3/4s of
those limits. Anything else can mean strange and intermittent
failures. If the meter is less accurate, then the voltage
readings must lie even further inside those limits.

Limits provided below are too wide. For example, upper
limit is 12.6. Below, that same limit is 13 volts - too
high. A voltage below 4.85 is too low. And yet limits below
are 4.5 - too low.

Don't screw around. Don't waste good money and time by
shotgunning - scam that an auto mechanic does when he does
not have basic knowledge. Get the meter to confirm an
essential component - the PSU. Then move on to other 'usual'
suspects using standard information sources such as system
(event) log, Device Manager, and comprehensive diagnostics
provided free by any reponsible computer manufacturer.


  #11  
Old January 18th 05, 12:49 AM
Ted
external usenet poster
 
Posts: n/a
Default +12 VOLT Indicator on Winbond Hardware Doctor

Hi,

Sorry for the late reply.
I have checked the voltage read outs using my new metre. They are as follows.

+3.3 is reading 3.40
+5.5 is reading 5.15
+12 is reading 11.92

and the - is reading -11.90

If I remember, the hardware doctor is reading the +12 volts to be 10.98. Is
it right in saying that this reading is being taken from the BIOS, therefore
the seems to nothing wrong with the PSU and the problem lies with the
motherboard?

Once again, sorry for the late reply

thanks for your help
Ted

"w_tom" wrote:

Meter has two leads. All voltages are 'electrical pressure'
between two points. The previously posted procedures describe
measuring voltage between two colored wires. IOW black lead
touches PSU black wire (inside white nylon connector where it
connects to motherboard). Red wire touches PSU's red, yellow,
orange, green etc wires to measure voltage on that wire. Just
set voltmeter selector to DC volts, touch probes, and read
numbers on meter. Record voltage for each colored wire. Then
compare to voltages on chart. 3.3, 5, and 12 volt wires
should read in upper 3/4s of limits.

Sidebar: Many 450 watt power supplies do not even output
their rated power. Just another problem with so many power
supplies dumped into America that don't even meet Intel
specs. This web site demonstrates a problem too common with
imported power supplies:
http://www6.tomshardware.com/howto/0...021/index.html

http://www6.tomshardware.com/howto/0...pplies-15.html
Time and time again, our lab measurements were unable to verify
the output figures represented on the model identification
sticker.



Ted wrote:
No, the PSU is a 450 Watt, I know what you mean, I should be getting
the correct details instead of wild guessing. I will buy a metre on
Saturday as I work shifts. I am not sure how to use a metre or where
I should be putting it to test, sorry if I sound stupid!! But you've
gotta start somewhere. Help with this is much appreciated.

"w_tom" wrote:

That 'swap PSU' test only implies that something else is
wrong. However assumed (and not stated): is the new PSU
exactly same? In the meantime, numbers are necessary to
provide useful assistance. Considering all the work and all
the added risk to both your system and his PSU, it makes more
sense (and saves significant time) to first take those voltage
readings.

Those upper and lower limits are significantly outside of
acceptable voltages. If you are getting alarms with limits
that far too wide, then surprising the computer is still
working. Winbond voltage readings are only as accurate as
hardware on motherboard. Use the meter so we know what your
system is really doing. Doing anything else will only make
you and us more confused. Those multimeter numbers are
essential. Without them, your responses will only be wild
speculation.

BTW what did those other information sources (Device
Manager, system log, etc) report? Worry more about getting
every piece of information requested. Being confused should
have come much later.

Ted wrote:
I have a friend that has let me borrow a PSU, when I check Winbond
hardware Doctor with the new PSU, instead of the alarm sounding now
and then, it's on constant.

Does that make any more sense? Im so confused???

"w_tom" wrote:
Obtain that meter even in a screw driver store. Meter is as
essential as a screw driver. So ubiquitous as to be sold even
in Home Depot, Sears, and Lowes. So inexpensive that it is
now a standard tool.

BIOS measurement circuits can vary significantly. How
accurate are they? An honest computer provider or motherboard
manufactuer provides that numerical specification. However a
'motherboard voltmeter' must be accurate enough duplicate the
accuracy of a 3.5 digit multimeter. See spec limits in
previous posts. Voltages must reside in the upper 3/4s of
those limits. Anything else can mean strange and intermittent
failures. If the meter is less accurate, then the voltage
readings must lie even further inside those limits.

Limits provided below are too wide. For example, upper
limit is 12.6. Below, that same limit is 13 volts - too
high. A voltage below 4.85 is too low. And yet limits below
are 4.5 - too low.

Don't screw around. Don't waste good money and time by
shotgunning - scam that an auto mechanic does when he does
not have basic knowledge. Get the meter to confirm an
essential component - the PSU. Then move on to other 'usual'
suspects using standard information sources such as system
(event) log, Device Manager, and comprehensive diagnostics
provided free by any reponsible computer manufacturer.


 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
Reloading windows XP Home Edition Bruce Nadamoto Security and Administration with Windows XP 3 November 11th 04 08:02 PM
SP2 and RAID Johannes Kantelberg Windows Service Pack 2 6 September 3rd 04 07:57 PM
To Atreju: Problem with adding hardware Anatoly Customizing Windows XP 1 August 2nd 04 04:15 PM
Problem with adding hardware Customizing Windows XP 0 August 2nd 04 07:03 AM
Device Drivers not detected on hardware install Doug Sherman [MVP] Networking and the Internet with Windows XP 23 July 30th 04 03:30 AM






All times are GMT +1. The time now is 09:55 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 PCbanter.
The comments are property of their posters.