If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Rate Thread | Display Modes |
|
#1
|
|||
|
|||
How to connect to a wireless device (a video camera's memory card)from windows 10?
I have a video camera with WiFi. I can switch its WiFi on, and the camera displays its WiFi SSID and password on its own screen.
How do I connect to this using Windows 10? My Windows 10 PC does not have WiFi, but it's connected by ethernet cable to a wireless router, which is where it gets its internet connection from. Why can I not see the camera from the PC? The wireless router is functional, as laptops can get onto the internet through it. |
#2
|
|||
|
|||
How to connect to a wireless device (a video camera's memory card) from windows 10?
On Sat, 05 Jan 2019 20:31:15 -0000, Commander Kinsey wrote:
I have a video camera with WiFi. I can switch its WiFi on, and the camera displays its WiFi SSID and password on its own screen. How do I connect to this using Windows 10? My Windows 10 PC does not have WiFi, but it's connected by ethernet cable to a wireless router, which is where it gets its internet connection from. Why can I not see the camera from the PC? The wireless router is functional, as laptops can get onto the internet through it. There are old school ways, and new school ways. I only know the old school ways. And, networking is complex, so I'm assuming simple SOHO setups here. Like 192.168.1.x is your subnet (where yours can be anything). Two things are critical in the old-school ways. 1. You must know the IP address of the device you wish to connect to 2. You must be on the SAME SUBNET as that IP address is on Giving examples, let's say the device is at IP address 192.168.1.10 And, let's assume that your router is at IP address 192.168.1.1 And let's assume a typical netmask of 255.255.255.0 (If that's all gobbleygook to you - then someone else will have to help.) What you do FIRST is ensure your PC is on the SAME SUBNET. You use "ipconfig" at the DOS command line to figure out your subnet. C:\ ipconfig Lots of stuff will be spit out, but one of the lines will be something like IPv4 Address. . . . . . . . . . . : 192.168.1.5 That will be the IP address of your PC. Notice that the first three sections are the same: 192.168.1.XXX That means you're on the same subnet. If you're NOT on the same subnet, then you usually can't connect. So get on the same subnet. That's your FIRST goal. Be on the same subnet. Then ping the device. C:\ ping -t 192.168.1.10 Practice ping by pinging your router ping -t 192.168.1.1 (Use "Control+C" to stop the pinging.) In short, if you're not on the same subnet, you're doomed (usually). So get on the same subnet first. Then ping the camera. If those two things don't happen, IMHO, nothing else will. |
#3
|
|||
|
|||
How to connect to a wireless device (a video camera's memorycard) from windows 10?
On Sat, 05 Jan 2019 20:42:59 -0000, arlen holder wrote:
On Sat, 05 Jan 2019 20:31:15 -0000, Commander Kinsey wrote: I have a video camera with WiFi. I can switch its WiFi on, and the camera displays its WiFi SSID and password on its own screen. How do I connect to this using Windows 10? My Windows 10 PC does not have WiFi, but it's connected by ethernet cable to a wireless router, which is where it gets its internet connection from. Why can I not see the camera from the PC? The wireless router is functional, as laptops can get onto the internet through it. There are old school ways, and new school ways. I only know the old school ways. And, networking is complex, so I'm assuming simple SOHO setups here. Like 192.168.1.x is your subnet (where yours can be anything). Two things are critical in the old-school ways. 1. You must know the IP address of the device you wish to connect to 2. You must be on the SAME SUBNET as that IP address is on Giving examples, let's say the device is at IP address 192.168.1.10 And, let's assume that your router is at IP address 192.168.1.1 And let's assume a typical netmask of 255.255.255.0 (If that's all gobbleygook to you - then someone else will have to help.) What you do FIRST is ensure your PC is on the SAME SUBNET. You use "ipconfig" at the DOS command line to figure out your subnet. C:\ ipconfig Lots of stuff will be spit out, but one of the lines will be something like IPv4 Address. . . . . . . . . . . : 192.168.1.5 That will be the IP address of your PC. Notice that the first three sections are the same: 192.168.1.XXX That means you're on the same subnet. If you're NOT on the same subnet, then you usually can't connect. So get on the same subnet. That's your FIRST goal. Be on the same subnet. Then ping the device. C:\ ping -t 192.168.1.10 Practice ping by pinging your router ping -t 192.168.1.1 (Use "Control+C" to stop the pinging.) In short, if you're not on the same subnet, you're doomed (usually). So get on the same subnet first. Then ping the camera. If those two things don't happen, IMHO, nothing else will. Thanks for the detailed explanation. I don't think the camera has an IP address, or I could have done the above (I used to be a network admin!) - I seem to have to use this weird "XDV" program. Apparently it's an app for android phone, iphone, or bluestacks (a PC/Mac/Unix phone emulator), which may or may not go through my wireless router. Pah, I'll just remove the memory card and plug it into the computer's card reader, I don't need to transfer files that often. Why couldn't the camera just use an IP address? It does have a USB socket, but the computer doesn't see it. The manual sort of (if I understand Chinglish correctly) indicates you should be able to transfer files by USB. Other than that, it's a damn good camera. £10 for a 4K (!) video camera only a few inches across, complete with waterproof housing, and about 10 attachments to fix it to bicycle handlebars, cycle helmet, etc, etc. I've tested it, and it does actually record a fairly decent 4K video (or 16MP still) in all lighting at 30fps (no zoom though). It'll do 90fps if you lower it to 720p. It'll record for 1 hour 20 minutes on internal battery, or 9 hours onto a 64GB memory card if you connect it to a USB powerbank (can't easily waterproof that though). I got an iphone sized Li-Ion powerbank for £20 that claims 12V 20Ah at up to 400 amps! It's for starting a car, and it does actually do that. Not tested the amp hour rating though. It's got a USB socket on it, so you can charge a phone/camera/etc with it. |
#4
|
|||
|
|||
How to connect to a wireless device (a video camera's memorycard) from windows 10?
On 05/01/2019 21:50, Commander Kinsey wrote:
It does have a USB socket, but the computer doesn't see it. The manual sort of (if I understand Chinglish correctly) indicates you should be able to transfer files by USB. Try, connecting the USB cable, then look at the camera's screen. Does it not show two options, the likes of; 'Connect to computer' or 'Use as Webcam'? |
#5
|
|||
|
|||
How to connect to a wireless device (a video camera's memorycard) from windows 10?
On Sat, 05 Jan 2019 23:32:55 -0000, Patrick wrote:
On 05/01/2019 21:50, Commander Kinsey wrote: It does have a USB socket, but the computer doesn't see it. The manual sort of (if I understand Chinglish correctly) indicates you should be able to transfer files by USB. Try, connecting the USB cable, then look at the camera's screen. Does it not show two options, the likes of; 'Connect to computer' or 'Use as Webcam'? It behaves as if I'd plugged it into a USB power supply. It charges the battery and nothing more. |
#6
|
|||
|
|||
How to connect to a wireless device (a video camera's memorycard) from windows 10?
On 06/01/2019 01:58, Commander Kinsey wrote:
On Sat, 05 Jan 2019 23:32:55 -0000, Patrick wrote: On 05/01/2019 21:50, Commander Kinsey wrote: It does have a USB socket, but the computer doesn't see it. The manual sort of (if I understand Chinglish correctly) indicates you should be able to transfer files by USB. Try, connecting the USB cable, then look at the camera's screen. Does it not show two options, the likes of; 'Connect to computer' or 'Use as Webcam'? It behaves as if I'd plugged it into a USB power supply.* It charges the battery and nothing more. Are you sure that you are using a Data-Cable rather than just a Charging-cable? |
#7
|
|||
|
|||
How to connect to a wireless device (a video camera's memorycard) from windows 10?
On Sat, 05 Jan 2019 20:31:15 -0000, Commander Kinsey wrote:
I have a video camera with WiFi. I can switch its WiFi on, and the camera displays its WiFi SSID and password on its own screen. How do I connect to this using Windows 10? My Windows 10 PC does not have WiFi, but it's connected by ethernet cable to a wireless router, which is where it gets its internet connection from. Why can I not see the camera from the PC? The wireless router is functional, as laptops can get onto the internet through it. And don't say "read the manual" - the manual is in Chinglish - for example: "When the poor operation of the product caused by the phenomenon of death, removable battery should be re-installed, then the machine returns to normal." The only pertinent info I can see in the manual is: "Before using WiFi function, please install "XDV" APP program on the smart phone" Surely if a smart phone can access it, so can a Windows 10 PC? |
#8
|
|||
|
|||
How to connect to a wireless device (a video camera's memorycard) from windows 10?
On 1/5/2019 2:43 PM, Commander Kinsey wrote:
On Sat, 05 Jan 2019 20:31:15 -0000, Commander Kinsey wrote: I have a video camera with WiFi.* I can switch its WiFi on, and the camera displays its WiFi SSID and password on its own screen. How do I connect to this using Windows 10?* My Windows 10 PC does not have WiFi, but it's connected by ethernet cable to a wireless router, which is where it gets its internet connection from.* Why can I not see the camera from the PC?* The wireless router is functional, as laptops can get onto the internet through it. And don't say "read the manual" - the manual is in Chinglish - for example: "When the poor operation of the product caused by the phenomenon of death, removable battery should be re-installed, then the machine returns to normal." The only pertinent info I can see in the manual is: "Before using WiFi function, please install "XDV" APP program on the smart phone" Surely if a smart phone can access it, so can a Windows 10 PC? A smart phone has wifi your PC does not. A smart phone needs a specific App installed, do you have a corresponding app for you PC? You can easily buy a wifi adapter for your PC. You have to find a suitable PC app. |
#9
|
|||
|
|||
How to connect to a wireless device (a video camera's memorycard) from windows 10?
On Sat, 05 Jan 2019 21:21:33 -0000, joe wrote:
On 1/5/2019 2:43 PM, Commander Kinsey wrote: On Sat, 05 Jan 2019 20:31:15 -0000, Commander Kinsey wrote: I have a video camera with WiFi. I can switch its WiFi on, and the camera displays its WiFi SSID and password on its own screen. How do I connect to this using Windows 10? My Windows 10 PC does not have WiFi, but it's connected by ethernet cable to a wireless router, which is where it gets its internet connection from. Why can I not see the camera from the PC? The wireless router is functional, as laptops can get onto the internet through it. And don't say "read the manual" - the manual is in Chinglish - for example: "When the poor operation of the product caused by the phenomenon of death, removable battery should be re-installed, then the machine returns to normal." The only pertinent info I can see in the manual is: "Before using WiFi function, please install "XDV" APP program on the smart phone" Surely if a smart phone can access it, so can a Windows 10 PC? A smart phone has wifi your PC does not. A smart phone needs a specific App installed, do you have a corresponding app for you PC? You can easily buy a wifi adapter for your PC. You have to find a suitable PC app. Looks like it's not standard networking protocols the camera uses. No IP address etc. I looked up "XDV" and apparently it's an app for android phone, iphone, or bluestacks (a PC/Mac/Unix phone emulator), which may or may not go through my wireless router. Pah, I'll just remove the memory card and plug it into the computer's card reader, I don't need to transfer files that often. Why couldn't the camera just use an IP address? |
#10
|
|||
|
|||
How to connect to a wireless device (a video camera's memory card) from windows 10?
In article , Commander Kinsey
wrote: The only pertinent info I can see in the manual is: "Before using WiFi function, please install "XDV" APP program on the smart phone" Surely if a smart phone can access it, so can a Windows 10 PC? A smart phone has wifi your PC does not. A smart phone needs a specific App installed, do you have a corresponding app for you PC? You can easily buy a wifi adapter for your PC. You have to find a suitable PC app. Looks like it's not standard networking protocols the camera uses. No IP address etc. it uses standard networking protocols and has an ip address. otherwise, it wouldn't work over wifi. I looked up "XDV" and apparently it's an app for android phone, iphone, or bluestacks (a PC/Mac/Unix phone emulator), which may or may not go through my wireless router. it doesn't. Pah, I'll just remove the memory card and plug it into the computer's card reader, I don't need to transfer files that often. Why couldn't the camera just use an IP address? it does, but it's on its own wifi network, thus the separate ssid. a quick check suggests it can't be configured to join your wifi network or any other wifi network. it is only an ad hoc access point. |
#11
|
|||
|
|||
How to connect to a wireless device (a video camera's memorycard) from windows 10?
On Sat, 05 Jan 2019 22:05:12 -0000, nospam wrote:
In article , Commander Kinsey wrote: The only pertinent info I can see in the manual is: "Before using WiFi function, please install "XDV" APP program on the smart phone" Surely if a smart phone can access it, so can a Windows 10 PC? A smart phone has wifi your PC does not. A smart phone needs a specific App installed, do you have a corresponding app for you PC? You can easily buy a wifi adapter for your PC. You have to find a suitable PC app. Looks like it's not standard networking protocols the camera uses. No IP address etc. it uses standard networking protocols and has an ip address. otherwise, it wouldn't work over wifi. I looked up "XDV" and apparently it's an app for android phone, iphone, or bluestacks (a PC/Mac/Unix phone emulator), which may or may not go through my wireless router. it doesn't. Why not? Pah, I'll just remove the memory card and plug it into the computer's card reader, I don't need to transfer files that often. Why couldn't the camera just use an IP address? it does, but it's on its own wifi network, thus the separate ssid. So why can't my computer access it as though it was a wireless router? And can I have say three laptops with no router and they communicate with each other over wireless? Could one produce an SSID and the other two connect to it? a quick check suggests it can't be configured to join your wifi network or any other wifi network. it is only an ad hoc access point. I don't understand. If it's using an IP address, why can't I find out that address and connect to it like any other device or computer? My assumption was it worked like that clamp thing I put next to my electricity meter, which uses the WiFi frequencies, but only communicates with it's own box, not a computer. I assumed it and the camera don't use TCP/IP, but just the same frequency range. |
#12
|
|||
|
|||
How to connect to a wireless device (a video camera's memory card) from windows 10?
On Sat, 05 Jan 2019 20:43:33 -0000, "Commander Kinsey"
wrote: On Sat, 05 Jan 2019 20:31:15 -0000, Commander Kinsey wrote: I have a video camera with WiFi. I can switch its WiFi on, and the camera displays its WiFi SSID and password on its own screen. The presence of an SSID and password tells you that the camera is an *access point*. You connect to an access point with a client. Your WiFi router is also an access point. Therefore, your WiFi router and your camera will not be able to see or connect to each other. How do I connect to this using Windows 10? My Windows 10 PC does not have WiFi, You purchase a WiFi adapter for your Win10 box that allows the PC to act as a WiFi *client*. Once you've done that, you'll be able to connect to the camera. Once connected, the camera will attempt to assign an IP address to your Win10 PC that is on the camera's subnet. You'll need to have DHCP enabled in Win10 for that to work. (Probably enabled by default.) The rules are simple: clients connect to access points. Access points do not initiate connections to clients, nor do access points connect to other access points. There's an exception for "ad hoc" wireless networks, but that doesn't sound like your situation. but it's connected by ethernet cable to a wireless router, which is where it gets its internet connection from. Why can I not see the camera from the PC? Because two access points don't see or connect to each other. Any PC *with WiFi* will be able to access the camera using the SSID and password that are displayed on the camera. Your Win10 box doesn't have WiFi so you can't connect with that PC. Add a WiFi adapter, turning your Win10 box into a Wifi Client, and you'll be able to connect. The wireless router is functional, as laptops can get onto the internet through it. And don't say "read the manual" - the manual is in Chinglish - for example: "When the poor operation of the product caused by the phenomenon of death, removable battery should be re-installed, then the machine returns to normal." The only pertinent info I can see in the manual is: "Before using WiFi function, please install "XDV" APP program on the smart phone" Surely if a smart phone can access it, so can a Windows 10 PC? A smart phone almost always has WiFi, meaning it can act as a WiFi *client*. Configured as a client, the smart phone can connect to an access point, such as your router or camera. Many smart phones can also be configured to act as a WiFi *access point*, but you don't need that functionality here. I only mention it for completeness. |
#13
|
|||
|
|||
How to connect to a wireless device (a video camera's memorycard) from windows 10?
On Sun, 06 Jan 2019 01:03:45 -0000, Char Jackson wrote:
On Sat, 05 Jan 2019 20:43:33 -0000, "Commander Kinsey" wrote: On Sat, 05 Jan 2019 20:31:15 -0000, Commander Kinsey wrote: I have a video camera with WiFi. I can switch its WiFi on, and the camera displays its WiFi SSID and password on its own screen. The presence of an SSID and password tells you that the camera is an *access point*. You connect to an access point with a client. Your WiFi router is also an access point. Therefore, your WiFi router and your camera will not be able to see or connect to each other. How do I connect to this using Windows 10? My Windows 10 PC does not have WiFi, You purchase a WiFi adapter for your Win10 box that allows the PC to act as a WiFi *client*. Once you've done that, you'll be able to connect to the camera. Once connected, the camera will attempt to assign an IP address to your Win10 PC that is on the camera's subnet. You'll need to have DHCP enabled in Win10 for that to work. (Probably enabled by default.) The rules are simple: clients connect to access points. Access points do not initiate connections to clients, nor do access points connect to other access points. There's an exception for "ad hoc" wireless networks, but that doesn't sound like your situation. but it's connected by ethernet cable to a wireless router, which is where it gets its internet connection from. Why can I not see the camera from the PC? Because two access points don't see or connect to each other. Any PC *with WiFi* will be able to access the camera using the SSID and password that are displayed on the camera. Your Win10 box doesn't have WiFi so you can't connect with that PC. Add a WiFi adapter, turning your Win10 box into a Wifi Client, and you'll be able to connect. The wireless router is functional, as laptops can get onto the internet through it. And don't say "read the manual" - the manual is in Chinglish - for example: "When the poor operation of the product caused by the phenomenon of death, removable battery should be re-installed, then the machine returns to normal." The only pertinent info I can see in the manual is: "Before using WiFi function, please install "XDV" APP program on the smart phone" Surely if a smart phone can access it, so can a Windows 10 PC? A smart phone almost always has WiFi, meaning it can act as a WiFi *client*. Configured as a client, the smart phone can connect to an access point, such as your router or camera. Many smart phones can also be configured to act as a WiFi *access point*, but you don't need that functionality here. I only mention it for completeness. I see, although as it requires I download an app to the phone, I'm guessing the camera doesn't do standard file sharing, which the phone's OS would do anyway. |
#14
|
|||
|
|||
How to connect to a wireless device (a video camera's memory card) from windows 10?
Kinsey wrote:
I have a video camera with WiFi. I can switch its WiFi on, and the camera displays its WiFi SSID and password on its own screen. So did you enter the password in the camera for the SSID of your wifi router (or to whatever wifi AP [access point] to which you want to connect the camera)? How do I connect to this using Windows 10? My Windows 10 PC does not have WiFi, but it's connected by ethernet cable to a wireless router, which is where it gets its internet connection from. Why can I not see the camera from the PC? The wireless router is functional, as laptops can get onto the internet through it. Use on of your PCs, like the laptops that can already connect via wifi or a desktop using wired Ethernet, to connect to the internal web server in the wifi router and look at the password specified there to allow devices to connect to it. Specify that wifi router's password in the wifi camera. You had to do the same when you connected your wifi laptops to the wifi router. |
#15
|
|||
|
|||
How to connect to a wireless device (a video camera's memorycard) from windows 10?
On 05/01/2019 20:31, Commander Kinsey wrote:
I have a video camera with WiFi. I can switch its WiFi on, and the camera displays its WiFi SSID and password on its own screen. Did it not come with a cable to connect it via your laptop's USB port? Most cameras I have bought have a cable. I have never bought a camera with wifi facility but I am not a keen photographer so this is not in point here. You are a new boy on the block here so this suggests to me that you are a nym-shifter expecting to generate useless posts by posting this crap here. Path: aioe.org!feeder.usenetexpress.com!feeder-in1.iad1.usenetexpress.com!news.alt.net From: "Commander Kinsey" Newsgroups: alt.comp.os.windows-10 Subject: How to connect to a wireless device (a video camera's memory card) from windows 10? Date: Sat, 05 Jan 2019 20:31:15 -0000 Organization: X Lines: 3 Message-ID: Mime-Version: 1.0 Content-Type: text/plain; charset=iso-8859-15; format=flowed; delsp=yes Content-Transfer-Encoding: 7bit User-Agent: Opera Mail/1.0 (Win32) X-Antivirus: AVG (VPS 190105-4, 05/01/2019), Outbound message X-Antivirus-Status: Clean Xref: aioe.org alt.comp.os.windows-10:82245 Actually you must be the same pedo we have filtered out but since you have changed your nym your post managed to come to my inbox!!! I have now updated by filter list!!. -- With over 950 million devices now running Windows 10, customer satisfaction is higher than any previous version of windows. |
|
Thread Tools | |
Display Modes | Rate This Thread |
|
|