A Windows XP help forum. PCbanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » PCbanter forum » Microsoft Windows 7 » Windows 7 Forum
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Migrating to an SSD



 
 
Thread Tools Rate Thread Display Modes
  #1  
Old March 24th 12, 03:20 AM posted to comp.sys.ibm.pc.hardware.storage,alt.comp.hardware.pc-homebuilt,alt.windows7.general
Yousuf Khan[_2_]
external usenet poster
 
Posts: 2,447
Default Migrating to an SSD

Okay, got myself an SSD now. So I want to migrate my Windows boot drive
to it. I have access to a couple of cloning utils that can properly copy
system disks and make them bootable, so that's not a problem. However,
I'm wondering if it's really that simple? I understand that there are
some tuning that needs to be done to SSD's, such as setting its cluster
sizes, etc. Also there is something called TRIM support that Windows 7
needs to implement. Is this something that's built into Windows 7 right
away, or is it something that needs to be installed? Anything else?

Yousuf Khan
Ads
  #2  
Old March 24th 12, 08:16 AM posted to comp.sys.ibm.pc.hardware.storage,alt.comp.hardware.pc-homebuilt,alt.windows7.general
Allen Drake
external usenet poster
 
Posts: 451
Default Migrating to an SSD

On Fri, 23 Mar 2012 22:20:48 -0400, Yousuf Khan
wrote:

Okay, got myself an SSD now. So I want to migrate my Windows boot drive
to it. I have access to a couple of cloning utils that can properly copy
system disks and make them bootable, so that's not a problem. However,
I'm wondering if it's really that simple? I understand that there are
some tuning that needs to be done to SSD's, such as setting its cluster
sizes, etc. Also there is something called TRIM support that Windows 7
needs to implement. Is this something that's built into Windows 7 right
away, or is it something that needs to be installed? Anything else?

Yousuf Khan

You can simply clone your system drive as I did at first when I
upgraded all my systems but that is not always the best option. You
need to know about SSD partition alignment
http://www.sevenforums.com/tutorials...alignment.html

http://www.sevenforums.com/tutorials...ndows-7-a.html

Al.
  #3  
Old March 24th 12, 08:27 AM posted to comp.sys.ibm.pc.hardware.storage,alt.comp.hardware.pc-homebuilt,alt.windows7.general
charlie[_2_]
external usenet poster
 
Posts: 707
Default Migrating to an SSD

On 3/23/2012 10:20 PM, Yousuf Khan wrote:
Okay, got myself an SSD now. So I want to migrate my Windows boot drive
to it. I have access to a couple of cloning utils that can properly copy
system disks and make them bootable, so that's not a problem. However,
I'm wondering if it's really that simple? I understand that there are
some tuning that needs to be done to SSD's, such as setting its cluster
sizes, etc. Also there is something called TRIM support that Windows 7
needs to implement. Is this something that's built into Windows 7 right
away, or is it something that needs to be installed? Anything else?

Yousuf Khan


Besides all of the above, there is another, perhaps quite important
consideration. SSDs are a good host for "static" files, and not so good
for dynamic ones. It would seem that windows should be reorganized on
that basis, with static directories and files on the SSD.
The registry will likely need manual editing to accommodate the changes.

(I have two SSDs (120G each) in systems that I'm going to "reorganize",
as soon as I figure out a reasonable way to accomplish the task.

There seem to be significant differences in setup between various mfrs
ssd drives. I'm still researching this one!

I've run across two different recommended cluster sizes, 1K and 4K.
(rounded size, not actual)

A comment I ran across was that AMDs controller does not pass the Trim
command.

  #4  
Old March 24th 12, 10:41 AM posted to alt.windows7.general
Dave-UK
external usenet poster
 
Posts: 596
Default Migrating to an SSD


"nothing but net" wrote in message hx...


The OP didn't say which SSD he has, so for example...
with an Intel SSD one would transfer the OS to the SSD with Intel's
utility to do that (an older version of Acronis True Image, or use a
newer version if on hand) - which will take care of partition
alignment. The Intel SSD Toolbox will take care of ensuring that
everything (Windows) is configured correctly for optimal operation.


I've found that the Intel toolbox does not modify the Windows 7 defrag schedule.
I've had to manually turn off defragging via the disk properties tools tab.

  #5  
Old March 24th 12, 12:37 PM posted to comp.sys.ibm.pc.hardware.storage,alt.comp.hardware.pc-homebuilt,alt.windows7.general
dweebken[_2_]
external usenet poster
 
Posts: 59
Default Migrating to an SSD

On 24/03/2012 1:20 PM, Yousuf Khan wrote:
Okay, got myself an SSD now. So I want to migrate my Windows boot drive
to it. I have access to a couple of cloning utils that can properly copy
system disks and make them bootable, so that's not a problem. However,
I'm wondering if it's really that simple? I understand that there are
some tuning that needs to be done to SSD's, such as setting its cluster
sizes, etc. Also there is something called TRIM support that Windows 7
needs to implement. Is this something that's built into Windows 7 right
away, or is it something that needs to be installed? Anything else?

Yousuf Khan

On a new SSD, first I had to create a partition and format the drive. I
then used Acronis trueimage Home 2012 to clone my laptop's HD to the
SSD. Then swapped the drives and the SSD booted up just fine. Then
Windows recognised a new drive in the system and loaded the drivers for
the SSD quite happily. then rebooted and just enjoyed the incredible
speed. It was as simple as that. Windows 7 has TRIM support built in.

My SSD is a Corsair Performance3 256 GB device, on a Toshiba Portege
R830 Laptop using Intel Core i5, and Win 7 Professional 64 Bit. Also
have 8GB RAM.

Also, once I had it working, I installed SSD tweaker from
http://elpamsoft.com/Downloads.aspx?Name=SSD%20Tweaker
and ran that.

Oh, you might want to also run ATTO Disk Benchmark before and after too,
to see the speed increas for yourself. It's free.

My laptop used to take 10 min and more to boot up from cold to useable.
Now it does a full reboot in under a minute.


hth
  #6  
Old March 24th 12, 01:14 PM posted to comp.sys.ibm.pc.hardware.storage,alt.comp.hardware.pc-homebuilt,alt.windows7.general
Bob I
external usenet poster
 
Posts: 9,943
Default Migrating to an SSD

You will see a LOT of opinions, some good, some not so. For my
installation, I decided on the drive, and then followed the
manufacturers recommendations for installation, setup and configuration.
For me that meant a clean install and load. So before creating your own
install procedure, read up.

On 3/23/2012 9:20 PM, Yousuf Khan wrote:
Okay, got myself an SSD now. So I want to migrate my Windows boot drive
to it. I have access to a couple of cloning utils that can properly copy
system disks and make them bootable, so that's not a problem. However,
I'm wondering if it's really that simple? I understand that there are
some tuning that needs to be done to SSD's, such as setting its cluster
sizes, etc. Also there is something called TRIM support that Windows 7
needs to implement. Is this something that's built into Windows 7 right
away, or is it something that needs to be installed? Anything else?

Yousuf Khan

  #7  
Old March 24th 12, 03:44 PM posted to comp.sys.ibm.pc.hardware.storage,alt.comp.hardware.pc-homebuilt,alt.windows7.general
Drew[_6_]
external usenet poster
 
Posts: 112
Default Migrating to an SSD

On 3/23/2012 7:20 PM, Yousuf Khan wrote:
Okay, got myself an SSD now. So I want to migrate my Windows boot drive
to it. I have access to a couple of cloning utils that can properly copy
system disks and make them bootable, so that's not a problem. However,
I'm wondering if it's really that simple? I understand that there are
some tuning that needs to be done to SSD's, such as setting its cluster
sizes, etc. Also there is something called TRIM support that Windows 7
needs to implement. Is this something that's built into Windows 7 right
away, or is it something that needs to be installed? Anything else?

Yousuf Khan

Recently did the same with a drive that had become too small to hold my
windows7.I installed a new Intel 120 gig ssd into my "box' and then
using the included Intel migration software it took approx 15 minutes or
less to migrate my boot drive to the new ssd. I then rebooted and
changed the boot order.At that point it changed my new drive to c: and
changed the old drive to L:. Worked perfectly and after 1 month I
formatted the old drive and it is now storage. Intel Migration Software
is just a free somewhat limited version of Acronis I believe and it is
updated frequently.I was leery about doing it but I found it was
amazingly easy and required very little on my part to perform this.
What brand of ssd did you purchase Yousuf?
  #8  
Old March 24th 12, 10:16 PM posted to comp.sys.ibm.pc.hardware.storage,alt.comp.hardware.pc-homebuilt,alt.windows7.general
Yousuf Khan[_2_]
external usenet poster
 
Posts: 2,447
Default Migrating to an SSD

On 24/03/2012 3:16 AM, Allen Drake wrote:
You can simply clone your system drive as I did at first when I
upgraded all my systems but that is not always the best option. You
need to know about SSD partition alignment
http://www.sevenforums.com/tutorials...alignment.html

http://www.sevenforums.com/tutorials...ndows-7-a.html


Good info, I'll read through these.

Yousuf Khan
  #9  
Old March 24th 12, 10:25 PM posted to comp.sys.ibm.pc.hardware.storage,alt.comp.hardware.pc-homebuilt,alt.windows7.general
Yousuf Khan[_2_]
external usenet poster
 
Posts: 2,447
Default Migrating to an SSD

On 24/03/2012 3:27 AM, charlie wrote:
Besides all of the above, there is another, perhaps quite important
consideration. SSDs are a good host for "static" files, and not so good
for dynamic ones. It would seem that windows should be reorganized on
that basis, with static directories and files on the SSD.
The registry will likely need manual editing to accommodate the changes.


That's actually something I was thinking about. Should I move things
like the swapfile, Thunderbird data, and just "User" folder in general,
off to regular storage?

Yousuf Khan
  #10  
Old March 24th 12, 10:26 PM posted to alt.windows7.general
BillW50
external usenet poster
 
Posts: 5,556
Default Migrating to an SSD

In hx,
nothing but net wrote:
That post is pretty much proof that comments one runs across should be
taken with a grain of salt.

The OP didn't say which SSD he has, so for example...
with an Intel SSD one would transfer the OS to the SSD with Intel's
utility to do that (an older version of Acronis True Image, or use a
newer version if on hand) - which will take care of partition
alignment...


I never found any older version of Acronis Tue Image get the partition
alignment right on an SSD. And the latest one I have is 2011. I am not
sure of 2012 gets it right or not.

--
Bill
Gateway M465e ('06 era) - OE-QuoteFix v1.19.2
Centrino Core Duo T2400 1.83GHz - 2GB - Windows XP SP3


  #11  
Old March 24th 12, 10:28 PM posted to comp.sys.ibm.pc.hardware.storage,alt.comp.hardware.pc-homebuilt,alt.windows7.general
Loren Pechtel[_2_]
external usenet poster
 
Posts: 18
Default Migrating to an SSD

On Fri, 23 Mar 2012 22:20:48 -0400, Yousuf Khan
wrote:

Okay, got myself an SSD now. So I want to migrate my Windows boot drive
to it. I have access to a couple of cloning utils that can properly copy
system disks and make them bootable, so that's not a problem. However,
I'm wondering if it's really that simple? I understand that there are
some tuning that needs to be done to SSD's, such as setting its cluster
sizes, etc. Also there is something called TRIM support that Windows 7
needs to implement. Is this something that's built into Windows 7 right
away, or is it something that needs to be installed? Anything else?


Windows 7 supports trim, no problem.

The issue that matters is that a simple copy onto the drive will
produce a misaligned layout that will be bad for performance. There
are programs out there that will take a drive and correctly align the
data, I have never looked into them.
  #12  
Old March 24th 12, 10:28 PM posted to comp.sys.ibm.pc.hardware.storage,alt.comp.hardware.pc-homebuilt,alt.windows7.general
Loren Pechtel[_2_]
external usenet poster
 
Posts: 18
Default Migrating to an SSD

On Sat, 24 Mar 2012 03:27:30 -0400, charlie wrote:

Besides all of the above, there is another, perhaps quite important
consideration. SSDs are a good host for "static" files, and not so good
for dynamic ones. It would seem that windows should be reorganized on
that basis, with static directories and files on the SSD.
The registry will likely need manual editing to accommodate the changes.

(I have two SSDs (120G each) in systems that I'm going to "reorganize",
as soon as I figure out a reasonable way to accomplish the task.


That's the theory at least but even though I didn't do anything to
keep the dynamic stuff off the SSDs I'm happy with how they are
performing.

I have a 256gb that hosts my Win7 system and a 128gb that hosts two
virtual machines. They've been in use for a year now and I've managed
to write so much to the 128gb one that it's life is down to 99%. The
256gb is still at 100%.
  #13  
Old March 24th 12, 10:38 PM posted to comp.sys.ibm.pc.hardware.storage,alt.comp.hardware.pc-homebuilt,alt.windows7.general
BillW50
external usenet poster
 
Posts: 5,556
Default Migrating to an SSD

In ,
Loren Pechtel wrote:
They've been in use for a year now and I've managed to write so much
to the 128gb one that it's life is down to 99%. The 256gb is still at
100%.


What are you using that tells you what the wear level is?

--
Bill
Gateway M465e ('06 era) - OE-QuoteFix v1.19.2
Centrino Core Duo T2400 1.83GHz - 2GB - Windows XP SP3


  #14  
Old March 24th 12, 11:08 PM posted to comp.sys.ibm.pc.hardware.storage,alt.comp.hardware.pc-homebuilt,alt.windows7.general
Allen Drake
external usenet poster
 
Posts: 451
Default Migrating to an SSD

On Sat, 24 Mar 2012 17:16:44 -0400, Yousuf Khan
wrote:

On 24/03/2012 3:16 AM, Allen Drake wrote:
You can simply clone your system drive as I did at first when I
upgraded all my systems but that is not always the best option. You
need to know about SSD partition alignment
http://www.sevenforums.com/tutorials...alignment.html

http://www.sevenforums.com/tutorials...ndows-7-a.html


Good info, I'll read through these.

Yousuf Khan


Did you mention which SSD you have? I just received number 10 a few
days ago. I have mostly Crucial and have had to update firmware twice
so far. Not a problem though.
  #15  
Old March 24th 12, 11:20 PM posted to comp.sys.ibm.pc.hardware.storage,alt.comp.hardware.pc-homebuilt,alt.windows7.general
Allen Drake
external usenet poster
 
Posts: 451
Default Migrating to an SSD

On Sat, 24 Mar 2012 17:25:32 -0400, Yousuf Khan
wrote:

On 24/03/2012 3:27 AM, charlie wrote:
Besides all of the above, there is another, perhaps quite important
consideration. SSDs are a good host for "static" files, and not so good
for dynamic ones. It would seem that windows should be reorganized on
that basis, with static directories and files on the SSD.
The registry will likely need manual editing to accommodate the changes.


That's actually something I was thinking about. Should I move things
like the swapfile, Thunderbird data, and just "User" folder in general,
off to regular storage?

Yousuf Khan

I would think it would depend on the capacity of the SSD. I use 256GB
SSDs and so far I have only used 60 GB. I do have backup HDDs
installed along with USB3 external for large video and music, etc.

I kept all the system files and document and download folders intact.
 




Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off






All times are GMT +1. The time now is 07:45 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 PCbanter.
The comments are property of their posters.