If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Rate Thread | Display Modes |
#1
|
|||
|
|||
Cloned/restored Win10Pro drive to NVMe drive -- won't boot
First I used Partition Magician's copy-to-SSD function, then again tried
Macrium Reflect to restore an image from one drive to another, but in neither case will the machine boot from that NVMe drive: "Windows failed to start.... Insert your Windows installation disc... Click 'Repair your computer.'" But this fails: "unable to repair" It complains about the file \Windows\system32\winload.exe and then "Status: 0xc000000e " But that file is present on the NVMe drive. Any alternative to reinstalling from scratch on the NVMe drive? And if I do so, can I then easily copy everything else on top of it so I get my original configuration back? BTW, the NVMe drive is not connected to the motherboard (which is too old to have that feature) but is mounted on a PCIe adapter, so it does not show in the BIOS but shows in the boot EasyBCD boot menu. Is that the problem? Can't the boot loader transfer control to *any* other drive? Perce |
Ads |
#2
|
|||
|
|||
Cloned/restored Win10Pro drive to NVMe drive -- won't boot
On 2020-04-01 6:54 p.m., Percival P. Cassidy wrote:
First I used Partition Magician's copy-to-SSD function, then again tried Macrium Reflect to restore an image from one drive to another, but in neither case will the machine boot from that NVMe drive: "Windows failed to start.... Insert your Windows installation disc... Click 'Repair your computer.'" But this fails: "unable to repair" It complains about the file \Windows\system32\winload.exe and then "Status: 0xc000000e " But that file is present on the NVMe drive. Any alternative to reinstalling from scratch on the NVMe drive? And if I do so, can I then easily copy everything else on top of it so I get my original configuration back? BTW, the NVMe drive is not connected to the motherboard (which is too old to have that feature) but is mounted on a PCIe adapter, so it does not show in the BIOS but shows in the boot EasyBCD boot menu. Is that the problem? Can't the boot loader transfer control to *any* other drive? Perce Apparently NVMe drives mounted on a PCIe card are not bootable, It has to be mounted in a motherboard socket, I tried this sometime ago and found that to be true. I now have a new M/B with 2 NVMe sockets and that works, and one useless PCIe card in my parts drawer. Rene |
#3
|
|||
|
|||
Cloned/restored Win10Pro drive to NVMe drive -- won't boot
Percival P. Cassidy wrote:
First I used Partition Magician's copy-to-SSD function, then again tried Macrium Reflect to restore an image from one drive to another, but in neither case will the machine boot from that NVMe drive: "Windows failed to start.... Insert your Windows installation disc... Click 'Repair your computer.'" But this fails: "unable to repair" It complains about the file \Windows\system32\winload.exe and then "Status: 0xc000000e " But that file is present on the NVMe drive. Any alternative to reinstalling from scratch on the NVMe drive? And if I do so, can I then easily copy everything else on top of it so I get my original configuration back? BTW, the NVMe drive is not connected to the motherboard (which is too old to have that feature) but is mounted on a PCIe adapter, so it does not show in the BIOS but shows in the boot EasyBCD boot menu. Is that the problem? Can't the boot loader transfer control to *any* other drive? Perce This link may help to answer all your Nvme questions: https://www.win-raid.com/t871f50-Gui...UEFI-BIOS.html If your bios cannot be modded then get a new MB. The speed increase is worth it. 10x faster than an SSD and 30x faster than a WD Black. |
#4
|
|||
|
|||
Cloned/restored Win10Pro drive to NVMe drive -- won't boot
Percival P. Cassidy wrote:
First I used Partition Magician's copy-to-SSD function, then again tried Macrium Reflect to restore an image from one drive to another, but in neither case will the machine boot from that NVMe drive: "Windows failed to start.... Insert your Windows installation disc... Click 'Repair your computer.'" But this fails: "unable to repair" It complains about the file \Windows\system32\winload.exe and then "Status: 0xc000000e " But that file is present on the NVMe drive. Any alternative to reinstalling from scratch on the NVMe drive? And if I do so, can I then easily copy everything else on top of it so I get my original configuration back? BTW, the NVMe drive is not connected to the motherboard (which is too old to have that feature) but is mounted on a PCIe adapter, so it does not show in the BIOS but shows in the boot EasyBCD boot menu. Is that the problem? Can't the boot loader transfer control to *any* other drive? Perce https://neosmart.net/wiki/0xc000000e...ection-failed/ The boot selection failed because a required device is inaccessible boot error message [Vista+] This implies that perhaps the driver method is not present or not possible. The OS could be switching over to its native driver at that point. Another possibility, is some wrinkle of Secure Boot. You should be able to UEFI boot without Secure Boot being enabled. For example, under trying conditions, I needed to set my Secure Boot to "Other OS" in the Asus BIOS, to get Windows 7 to boot. Even though Windows 7 is a Microsoft OS, the key for Microsoft OSes might not work with Windows 7. Since it sounds like you're using a native NVMe slot and not some bodged PCI Express card, maybe the motherboard end of things is otherwise OK. Perhaps there is NVMe support baked into the BIOS, so INT 0x13 calls (DOS style reads) work until the handoff to the OS driver. What you could look at, is boot from the previous device, and check Device Manager and see if there is a driver for the NVMe showing. Plus, go over to the Disk Management window and verify the NVMe can be "explored" and the files are visible. This proves that the original disk had an OS NVMe driver. If these things were not true, you'd try and get the NVMe to be "visible" while using the original disk, before cloning over again. Without any articles, these are things I'd try or look at, before sallying forth to Google. I looked at the Neosmart one, so I could get a nicer string to look at. I think I also had a problem once, where winload.exe, the signing on it had failed, and Windows then didn't want to use the winload.exe file. But that's probably a different failure code too. Paul |
#5
|
|||
|
|||
Cloned/restored Win10Pro drive to NVMe drive -- won't boot
"Percival P. Cassidy" wrote:
First I used Partition Magician's copy-to-SSD function, then again tried Macrium Reflect to restore an image from one drive to another, but in neither case will the machine boot from that NVMe drive: "Windows failed to start.... Insert your Windows installation disc... Click 'Repair your computer.'" Do another restore. Then boot back into Macrium Reflect and do a repair. I forget what the path is, just look around for "fix boot problems" or whatever. You might be able to do that without a reboot after the restore, but I would reboot first (especially to see if the problem exists). |
#6
|
|||
|
|||
Cloned/restored Win10Pro drive to NVMe drive -- won't boot
On 4/2/20 9:54 AM, John Doe wrote:
First I used Partition Magician's copy-to-SSD function, then again tried Macrium Reflect to restore an image from one drive to another, but in neither case will the machine boot from that NVMe drive: "Windows failed to start.... Insert your Windows installation disc... Click 'Repair your computer.'" Do another restore. Then boot back into Macrium Reflect and do a repair. I forget what the path is, just look around for "fix boot problems" or whatever. You might be able to do that without a reboot after the restore, but I would reboot first (especially to see if the problem exists). Already tried that -- no joy. I'm going to try the solutions in the link posted by Paul in Houston TX. Perce |
#7
|
|||
|
|||
Cloned/restored Win10Pro drive to NVMe drive -- won't boot
In article ,
Percival P. Cassidy wrote: On 4/2/20 9:54 AM, John Doe wrote: First I used Partition Magician's copy-to-SSD function, then again tried Macrium Reflect to restore an image from one drive to another, but in neither case will the machine boot from that NVMe drive: "Windows failed to start.... Insert your Windows installation disc... Click 'Repair your computer.'" Do another restore. Then boot back into Macrium Reflect and do a repair. I forget what the path is, just look around for "fix boot problems" or whatever. You might be able to do that without a reboot after the restore, but I would reboot first (especially to see if the problem exists). Already tried that -- no joy. I'm going to try the solutions in the link posted by Paul in Houston TX. You're going to travel all the way to Texas to test it? -- BigBusiness types (aka, Republicans/Conservatives/Independents/Liberatarians/whatevers) don't hate big government. They *love* big government as a means for them to get rich, sucking off the public teat. What they don't like is *democracy* - you know, like people actually having the right to vote and stuff like that. |
#8
|
|||
|
|||
Cloned/restored Win10Pro drive to NVMe drive -- won't boot
"Percival P. Cassidy" wrote:
John Doe wrote: First I used Partition Magician's copy-to-SSD function, then again tried Macrium Reflect to restore an image from one drive to another, but in neither case will the machine boot from that NVMe drive: "Windows failed to start.... Insert your Windows installation disc... Click 'Repair your computer.'" Do another restore. Then boot back into Macrium Reflect and do a repair. I forget what the path is, just look around for "fix boot problems" or whatever. You might be able to do that without a reboot after the restore, but I would reboot first (especially to see if the problem exists). Already tried that Have you tried a clean install? |
#9
|
|||
|
|||
Cloned/restored Win10Pro drive to NVMe drive -- won't boot
On 2020-04-02 10:28 a.m., Percival P. Cassidy wrote:
On 4/2/20 9:54 AM, John Doe wrote: First I used Partition Magician's copy-to-SSD function, then again tried Macrium Reflect to restore an image from one drive to another, but in neither case will the machine boot from that NVMe drive: "Windows failed to start.... Insert your Windows installation disc... Click 'Repair your computer.'" Do another restore. Then boot back into Macrium Reflect and do a repair. I forget what the path is, just look around for "fix boot problems" or whatever. You might be able to do that without a reboot after the restore, but I would reboot first (especially to see if the problem exists). Already tried that -- no joy. I'm going to try the solutions in the link posted by Paul in Houston TX. Perce That looks like a good article, sure worth trying some of their fixes. Rene |
Thread Tools | |
Display Modes | Rate This Thread |
|
|