If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Do any stores still sell floppy disks?
My bootable DOS floppy disk died. I had not used it in several years,
but wanted to boot up with the floppy to install a new harddrive on an old Windows 98 machine, with no CD drive. I have looked in several stores. None sell them anymore. I found a 5pack on ebay, for $5 and bought them. That was the cheapest I found for NEW ones. Some were ridiculously priced, and there were some used ones selling cheap, and saying "no returns" "untested", etc. I'll pass on those!!! Then there was someone selling 20 dead 5.25 inch floppies for around $29, plus $10 shipping. It said "For Art Projects".... (Apparently his garbage can is full, and he really thinks he will find a sucker).... Someone even had some 8" floppies. I heard of them, but never saw them. That's got to be very old. Anyhow, I am just curious if anyone has seen any floppies in any stores lately. Just curious, how much data did those 8" floppies hold? I have a feeling they held less than the 360K 5.25 Inch..... |
Ads |
#2
|
|||
|
|||
Do any stores still sell floppy disks?
|
#3
|
|||
|
|||
Do any stores still sell floppy disks?
|
#4
|
|||
|
|||
Do any stores still sell floppy disks?
On Fri, 3 Nov 2017 17:50:11 +0000, "J. P. Gilliver (John)"
wrote: Just curious, how much data did those 8" floppies hold? I have a feeling they held less than the 360K 5.25 Inch..... I think it was some tens of k - maybe 80K? (or 64?) Possibly, not least _because_ of the low capacity (and thus density), they might actually be quite reliable. I don't think I'd want to try though (-:! The 360K was just the IBM PC capacity - and that for double-sided discs; 5¼" discs when used in other machines had different capacities - same discs. DFS on the BBC Micro, for example, was IIRR 100K a side (and ADFS on the BBC Master 160K a side). That was for 80 track drives - half that for 40 track drives. -- IBM had 1 meg 8" floppies and 2.4 meg 5.25" along with the 2.88m 3.5s |
#5
|
|||
|
|||
Do any stores still sell floppy disks?
james wrote:
My bootable DOS floppy disk died. I had not used it in several years, but wanted to boot up with the floppy to install a new harddrive on an old Windows 98 machine, with no CD drive. I have looked in several stores. None sell them anymore. I found a 5pack on ebay, for $5 and bought them. That was the cheapest I found for NEW ones. Some were ridiculously priced, and there were some used ones selling cheap, and saying "no returns" "untested", etc. I'll pass on those!!! Then there was someone selling 20 dead 5.25 inch floppies for around $29, plus $10 shipping. It said "For Art Projects".... (Apparently his garbage can is full, and he really thinks he will find a sucker).... Someone even had some 8" floppies. I heard of them, but never saw them. That's got to be very old. Anyhow, I am just curious if anyone has seen any floppies in any stores lately. Just curious, how much data did those 8" floppies hold? I have a feeling they held less than the 360K 5.25 Inch..... So it is top secret that only you know what size floppy you want. Could be 3.5", 5.25", or 8". You only mentioned the 8" size (Pelican) and those are far older than your XP computer. http://preview.tinyurl.com/y92odc83 Change "3.5" to whatever size you need. The price is high because of the prolonged storage costs for ancient media. You're trying to acquire a portion of a very limited inventory. How do you know the floppy diskette is the problem. Maybe it is the floppy drive. Have you tested other floppies in the drive to make sure the drive is working? All magnetic media incurs dipole stress which means it loses retentivity over time. The dipoles are no longer perpendicular and the less they are the weaker becomes the bits. That's why all magnetic media requires refreshing, especially for those areas that never change (only read, never written). Most users replace hard disks long before retentivity (data integrity) becomes a problem but floppies become weaker faster. Every time a floppy is read, there is friction to the media from the head riding against the diskette. HDDs have their heads flying OFF the surface. The more you use floppies, the faster they wear out. The soft cotton-like padding inside is to brush off and cling to the loosened particles. Their data integrity also becomes unreliable after a few years due to dipole stress in a flexible media (unless refreshed). There are tools to refresh magnetic media. I remember GRC Spinrite had it. Others have a refresh, too (I think HDD Regenerator has refresh). Haven't needed them in so long that I long ago was too old in my version of Spinrite to qualify for an upgrade (and it costs more than many HDDs). https://www.storagecraft.com/blog/da...rage-lifespan/ |
#6
|
|||
|
|||
Do any stores still sell floppy disks?
In message , VanguardLH
writes: james wrote: My bootable DOS floppy disk died. I had not used it in several years, but wanted to boot up with the floppy to install a new harddrive on an old Windows 98 machine, with no CD drive. I have looked in several stores. None sell them anymore. I found a 5pack on ebay, for $5 and bought them. That was the cheapest I found for NEW ones. Some were ridiculously priced, and there were some used ones selling cheap, and saying "no returns" "untested", etc. I'll pass on those!!! Then there was someone selling 20 dead 5.25 inch floppies for around $29, plus $10 shipping. It said "For Art Projects".... (Apparently his garbage can is full, and he really thinks he will find a sucker).... Someone even had some 8" floppies. I heard of them, but never saw them. That's got to be very old. Anyhow, I am just curious if anyone has seen any floppies in any stores lately. Just curious, how much data did those 8" floppies hold? I have a feeling they held less than the 360K 5.25 Inch..... So it is top secret that only you know what size floppy you want. Could be 3.5", 5.25", or 8". You only mentioned the 8" size (Pelican) and those are far older than your XP computer. It was fairly clear to me that his mention of the 8" ones was only that he found someone selling some. I agree it's not clear whether he wanted 3½ or 5¼, though I think the former since he mentions the latter only re the art-seller. http://preview.tinyurl.com/y92odc83 Change "3.5" to whatever size you need. The price is high because of the prolonged storage costs for ancient media. You're trying to acquire a portion of a very limited inventory. (Note: VanguardLH is just saying "use Google", but hiding that by using tinyurl. Above is _not_ a link to a specifc vendor. Thinking it was, I followed it, thinking 'I bet they don't have 3" ones' [as opposed to 3½], but of course I couldn't. [3" was a - IMO, superior, for mechanical reasons - format that came out about the same time the 3½" one did, but never caught on, presumably as it must have cost more to make.]) How do you know the floppy diskette is the problem. Maybe it is the floppy drive. Have you tested other floppies in the drive to make sure the drive is working? That's a good point. All magnetic media incurs dipole stress which means it loses retentivity over time. The dipoles are no longer perpendicular and the less they are the weaker becomes the bits. That's why all magnetic media requires refreshing, especially for those areas that never change (only read, Though true that magnetic media lose retentivity over time (so should be refreshed/copied), I'm not sure they all involve _perpendicular_ dipoles; certainly linear recording tape doesn't, and I don't _think_ floppies do. I think most HD technologies do. [] -- J. P. Gilliver. UMRA: 1960/1985 MB++G()AL-IS-Ch++(p)Ar@T+H+Sh0!:`)DNAf The average US shareholding lasts 22 seconds. Nobody knows who invented the fire hydrant: the patent records were destroyed in a fire. Sandcastles kill more people than sharks. Your brain uses less power than the light in your fridge. The Statue of Liberty wears size 879 shoes. - John Lloyd, QI supremo (RT, 2014/9/27-10/3) |
#7
|
|||
|
|||
Do any stores still sell floppy disks?
J. P. Gilliver (John) wrote:
VanguardLH WROTE: james wrote: My bootable DOS floppy disk died. I had not used it in several years, but wanted to boot up with the floppy to install a new harddrive on an old Windows 98 machine, with no CD drive. I have looked in several stores. None sell them anymore. I found a 5pack on ebay, for $5 and bought them. That was the cheapest I found for NEW ones. Some were ridiculously priced, and there were some used ones selling cheap, and saying "no returns" "untested", etc. I'll pass on those!!! Then there was someone selling 20 dead 5.25 inch floppies for around $29, plus $10 shipping. It said "For Art Projects".... (Apparently his garbage can is full, and he really thinks he will find a sucker).... Someone even had some 8" floppies. I heard of them, but never saw them. That's got to be very old. Anyhow, I am just curious if anyone has seen any floppies in any stores lately. Just curious, how much data did those 8" floppies hold? I have a feeling they held less than the 360K 5.25 Inch..... So it is top secret that only you know what size floppy you want. Could be 3.5", 5.25", or 8". You only mentioned the 8" size (Pelican) and those are far older than your XP computer. It was fairly clear to me that his mention of the 8" ones was only that he found someone selling some. I agree it's not clear whether he wanted 3½ or 5¼, though I think the former since he mentions the latter only re the art-seller. Except I don't remember any PC-XT in 1982 or later "PCs" having an internal 8" floppy drive. Those were externally attached drives on PCs. They did come with 5.25" internal drives. There may be custom setups that had 8" drives as internal, like the old IBM 360 mainframes that used an 8" floppy for the IPL (inital program load) but I severely doubt the OP is running Windows XP on that setup. I don't recall what was the minimum hardware requirement for Windows XP but I don't think an old 8088 even with a Nec V20 coprocessor was acceptable to the XP installer. https://support.microsoft.com/en-us/...rating-systems That probably excludes any old consumer-grade PC that had an internal 8" floppy. The OP never actually mentioned the floppy drive was internal (attached to mobo controller or daughtercard) or external (via parallel, serial, USB, or other hardware protocol interface). http://preview.tinyurl.com/y92odc83 Change "3.5" to whatever size you need. The price is high because of the prolonged storage costs for ancient media. You're trying to acquire a portion of a very limited inventory. (Note: VanguardLH is just saying "use Google", but hiding that by using tinyurl. Above is _not_ a link to a specifc vendor. Thinking it was, I followed it, thinking 'I bet they don't have 3" ones' [as opposed to 3½], but of course I couldn't. [3" was a - IMO, superior, for mechanical reasons - format that came out about the same time the 3½" one did, but never caught on, presumably as it must have cost more to make.]) It's Froogle, or Google's Shopping search. I did a search on 3.5" floppies and found some sellers. No, doesn't look like they are cheap. The Google search URL is ridiculously long hence the use of a short redirection URL; however, unlike other redirection services, TinyURL lets me specify the preview hostname so users can see to where the URL points BEFORE they get pushed to there. All magnetic media incurs dipole stress which means it loses retentivity over time. The dipoles are no longer perpendicular and the less they are the weaker becomes the bits. That's why all magnetic media requires refreshing, especially for those areas that never change (only read, Though true that magnetic media lose retentivity over time (so should be refreshed/copied), I'm not sure they all involve _perpendicular_ dipoles; certainly linear recording tape doesn't, and I don't _think_ floppies do. I think most HD technologies do. 1 bits are those dipoles perpendicular to the reading direction. Over time due to dipole stress (magnetic relaxation), the dipole field becomes less than perpendicular until completely relaxed and indistinguishable as a differentiation as a 1 bit. Even zeroes must be stressed (written) to provide differentiation. The less the differentiation (the more relaxed the dipole) the less likely the media provides reliable distinction between of bit state. I'm not discussing whether the media uses longtitudinal or perpendicular recording regarding the physical media and the sensor head. Sorry, perpendicular was incorrect as often I see the dipoles are 180 degrees differentiated regardless of recording direction. In old HDDs, the dipoles were arranged longitudinally (horizontal and parallel to the platter surface) but changed to perpendicular recording to increase density. However, the 1 and 0 dipoles are opposite of each other (180 degrees, not perpendicular as I said) to provide differentiation between those states. I don't recall what floppies used for magnetic recording orientation. I think tape had the dipoles perpendicular to the direction of the tape movement but I'd have to check. Also, without a change in the recording material, going to higher density means less material (grains) of magnetic material used for a dipole (or magnetic domain). The whole point was that magnetic media that sits around un-refreshed will lose retentivity of its data. Magnetic material can resist self-demagnetization but not stop it. My recollection is that tape was better than floppies for archival storage. I've seen companies that stored archival data on floppies even under excellent environmental conditions but still lose data (but those using tape did not). That was long ago where they learned the hard way that floppies are not for archival storage. One company where I was the software librarian (just one of many duties in a hydra job) would store HDDs with the OS, software product version(s), and all support software to archive the product. Periodically I also had to order, test, and archive an entire PC with the HDDs to make sure the technology was still available some 20 to 40 years later. This was to make sure the product could be reproduced or tested again under the same conditions as for a customer using an old product on an old OS on old hardware. There were some customers still using 30-old versions of the enterprise software. If they pay for support then they get it but we needed to ensure we could oblige. I think the oldest stuff involved mortgages because that data and software to use it has to be around for 40 years by law. The OP really needs to test if the drive is bad or just the floppy (whatever size). Presumably if he has one diskette then he has some more he can use for testing. They were mechanical drives and I remember running into a few that get out of alignment. In fact, a floppy that was formatted and read/wrote just fine in one computer was unusable in another computer with the same type of drive. One of the drives was out of alignment. No idea if the boot floppy the OP has was created using the drive in the computer he is trying to boot or written using a drive in a different computer. |
#8
|
|||
|
|||
Do any stores still sell floppy disks?
On 11/4/2017 11:53 AM, VanguardLH wrote:
J. P. Gilliver (John) wrote: VanguardLH WROTE: james wrote: My bootable DOS floppy disk died. I had not used it in several years, but wanted to boot up with the floppy to install a new harddrive on an old Windows 98 machine, with no CD drive. I have looked in several stores. None sell them anymore. I found a 5pack on ebay, for $5 and bought them. That was the cheapest I found for NEW ones. Some were ridiculously priced, and there were some used ones selling cheap, and saying "no returns" "untested", etc. I'll pass on those!!! Then there was someone selling 20 dead 5.25 inch floppies for around $29, plus $10 shipping. It said "For Art Projects".... (Apparently his garbage can is full, and he really thinks he will find a sucker).... Someone even had some 8" floppies. I heard of them, but never saw them. That's got to be very old. Anyhow, I am just curious if anyone has seen any floppies in any stores lately. Just curious, how much data did those 8" floppies hold? I have a feeling they held less than the 360K 5.25 Inch..... So it is top secret that only you know what size floppy you want. Could be 3.5", 5.25", or 8". You only mentioned the 8" size (Pelican) and those are far older than your XP computer. It was fairly clear to me that his mention of the 8" ones was only that he found someone selling some. I agree it's not clear whether he wanted 3½ or 5¼, though I think the former since he mentions the latter only re the art-seller. Except I don't remember any PC-XT in 1982 or later "PCs" having an internal 8" floppy drive. Those were externally attached drives on PCs. They did come with 5.25" internal drives. There may be custom setups that had 8" drives as internal, like the old IBM 360 mainframes that used an 8" floppy for the IPL (inital program load) but I severely doubt the OP is running Windows XP on that setup. I don't recall what was the minimum hardware requirement for Windows XP but I don't think an old 8088 even with a Nec V20 coprocessor was acceptable to the XP installer. https://support.microsoft.com/en-us/...rating-systems That probably excludes any old consumer-grade PC that had an internal 8" floppy. The OP never actually mentioned the floppy drive was internal (attached to mobo controller or daughtercard) or external (via parallel, serial, USB, or other hardware protocol interface). http://preview.tinyurl.com/y92odc83 Change "3.5" to whatever size you need. The price is high because of the prolonged storage costs for ancient media. You're trying to acquire a portion of a very limited inventory. (Note: VanguardLH is just saying "use Google", but hiding that by using tinyurl. Above is _not_ a link to a specifc vendor. Thinking it was, I followed it, thinking 'I bet they don't have 3" ones' [as opposed to 3½], but of course I couldn't. [3" was a - IMO, superior, for mechanical reasons - format that came out about the same time the 3½" one did, but never caught on, presumably as it must have cost more to make.]) It's Froogle, or Google's Shopping search. I did a search on 3.5" floppies and found some sellers. No, doesn't look like they are cheap. The Google search URL is ridiculously long hence the use of a short redirection URL; however, unlike other redirection services, TinyURL lets me specify the preview hostname so users can see to where the URL points BEFORE they get pushed to there. All magnetic media incurs dipole stress which means it loses retentivity over time. The dipoles are no longer perpendicular and the less they are the weaker becomes the bits. That's why all magnetic media requires refreshing, especially for those areas that never change (only read, Though true that magnetic media lose retentivity over time (so should be refreshed/copied), I'm not sure they all involve _perpendicular_ dipoles; certainly linear recording tape doesn't, and I don't _think_ floppies do. I think most HD technologies do. 1 bits are those dipoles perpendicular to the reading direction. Over time due to dipole stress (magnetic relaxation), the dipole field becomes less than perpendicular until completely relaxed and indistinguishable as a differentiation as a 1 bit. Even zeroes must be stressed (written) to provide differentiation. The less the differentiation (the more relaxed the dipole) the less likely the media provides reliable distinction between of bit state. I'm not discussing whether the media uses longtitudinal or perpendicular recording regarding the physical media and the sensor head. Sorry, perpendicular was incorrect as often I see the dipoles are 180 degrees differentiated regardless of recording direction. In old HDDs, the dipoles were arranged longitudinally (horizontal and parallel to the platter surface) but changed to perpendicular recording to increase density. However, the 1 and 0 dipoles are opposite of each other (180 degrees, not perpendicular as I said) to provide differentiation between those states. I don't recall what floppies used for magnetic recording orientation. I think tape had the dipoles perpendicular to the direction of the tape movement but I'd have to check. Also, without a change in the recording material, going to higher density means less material (grains) of magnetic material used for a dipole (or magnetic domain). The whole point was that magnetic media that sits around un-refreshed will lose retentivity of its data. Magnetic material can resist self-demagnetization but not stop it. My recollection is that tape was better than floppies for archival storage. I've seen companies that stored archival data on floppies even under excellent environmental conditions but still lose data (but those using tape did not). That was long ago where they learned the hard way that floppies are not for archival storage. One company where I was the software librarian (just one of many duties in a hydra job) would store HDDs with the OS, software product version(s), and all support software to archive the product. Periodically I also had to order, test, and archive an entire PC with the HDDs to make sure the technology was still available some 20 to 40 years later. This was to make sure the product could be reproduced or tested again under the same conditions as for a customer using an old product on an old OS on old hardware. There were some customers still using 30-old versions of the enterprise software. If they pay for support then they get it but we needed to ensure we could oblige. I think the oldest stuff involved mortgages because that data and software to use it has to be around for 40 years by law. The OP really needs to test if the drive is bad or just the floppy (whatever size). Presumably if he has one diskette then he has some more he can use for testing. They were mechanical drives and I remember running into a few that get out of alignment. In fact, a floppy that was formatted and read/wrote just fine in one computer was unusable in another computer with the same type of drive. One of the drives was out of alignment. No idea if the boot floppy the OP has was created using the drive in the computer he is trying to boot or written using a drive in a different computer. one of the frequently encountered failures happens when 'cat hair' gets on the head rails. Calibration steps it to the end and references from there. The cat hair moved it off track. |
#9
|
|||
|
|||
Do any stores still sell floppy disks?
On Sat, 4 Nov 2017 03:48:30 -0500, VanguardLH wrote:
There are tools to refresh magnetic media. I remember GRC Spinrite had it. Others have a refresh, too (I think HDD Regenerator has refresh). Haven't needed them in so long that I long ago was too old in my version of Spinrite to qualify for an upgrade (and it costs more than many HDDs). Going way back to the Dos days, I had a friend who I'll refer to as a "computer geek". He was good as a technician, hacker, and probably had darn near every piece of software one needed at that time. I had an old IBM PC (floppy only) computer. I took it to him, and he hooked up a hard drive to it. I still recall buying that USED hard drive at a computer store, and paying a fortune for it. It was something like 10 megs. After connecting the hard drive, he ran Spin Rite on it. I recall that took hours and I had to come back the next day to get my stuff, since I think it ran all night. The next day I got my computer and he said that my hard drive was good. I was new at all this stuff, and I was impressed by Spin Rite, so before I left, he gave me a copy of it on a floppy. Since I later archived all my floppies onto a hard drive, I still have that old Spin Rite. So, if I boot my Win98 machine to Dos, can I run that old version of Spin Rite to regenerate some floppies? Will that work? I have not used any of that old stuff in years, but I always kept all software if it was useful. Also, since I just bought 5 new blank floppies on ebay, should I run it on them? They are NEW floppies, but probably "new old stock". I had already planned to re-format them, but maybe I should do more.... I knew that floppies went bad over time, but I never knew why. Now I do. Thanks for the info. |
#10
|
|||
|
|||
Do any stores still sell floppy disks?
|
#11
|
|||
|
|||
Do any stores still sell floppy disks?
|
Thread Tools | |
Display Modes | |
|
|