A Windows XP help forum. PCbanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » PCbanter forum » Microsoft Windows XP » Customizing Windows XP
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Important please read this Thank you `°º·...·º°`°º·...·º°`°º·.?..·



 
 
Thread Tools Display Modes
  #1  
Old May 16th 05, 09:31 PM
Cricket
external usenet poster
 
Posts: n/a
Default Important please read this Thank you `°º·...·º°`°º·...·º°`°º·.?..·

I installed a second hard drive in my Dell. It only came with 40 GB, 35 for
extra programs. The 2nd was a 120 GB. I wired it as the original to be the
primary since it had the xp on it. Is there a way to switch the 120 to the
default without rewiring the 2 hard drives

"unknown" wrote:


Ads
  #2  
Old May 17th 05, 07:19 PM
Thorsten Matzner
external usenet poster
 
Posts: n/a
Default

"Cricket" wrote:

I installed a second hard drive in my Dell. It only came with 40 GB, 35 for
extra programs. The 2nd was a 120 GB. I wired it as the original to be the
primary since it had the xp on it. Is there a way to switch the 120 to the
default without rewiring the 2 hard drives


If you mean that you want to move the data from the old to the new
HDD: "How to Move a Windows XP Installation to Different Hardware"
(http://support.microsoft.com/?kbid=314070).

--
(tm)
  #3  
Old May 17th 05, 08:01 PM
Mike Hall \(MS-MVP\)
external usenet poster
 
Posts: n/a
Default

Thorsten

That link appears not to be available..

--
Mike Hall
MVP - Windows Shell/User
http://dts-l.org/goodpost.htm





"Thorsten Matzner" wrote in message
...
"Cricket" wrote:

I installed a second hard drive in my Dell. It only came with 40 GB, 35
for
extra programs. The 2nd was a 120 GB. I wired it as the original to be the
primary since it had the xp on it. Is there a way to switch the 120 to the
default without rewiring the 2 hard drives


If you mean that you want to move the data from the old to the new
HDD: "How to Move a Windows XP Installation to Different Hardware"
(http://support.microsoft.com/?kbid=314070).

--
(tm)



  #4  
Old May 18th 05, 01:00 PM
Thorsten Matzner
external usenet poster
 
Posts: n/a
Default

"Mike Hall \(MS-MVP\)" wrote:

Thorsten

That link appears not to be available..


Here is the text:

"Knowledge Base: Dutch

How to Move a Windows XP Installation to Different
HardwareArtikelnummer: 314070

Laatst gewijzigd: 10-4-2003


--------------------------------------------------------------------------------
De informatie in dit artikel is van toepassing op:


Microsoft Windows XP Home Edition
Microsoft Windows XP Professional

--------------------------------------------------------------------------------

Dit artikel is eerder gepubliceerd onder NL314070
For a Microsoft Windows 2000 version of this article, see 249694.

IMPORTANT : The issues that are discussed in this article and in the
linked articles are the most common problems and limitations that you
may encounter when you try to restore a backup copy to different
hardware. Other issues can also appear because of the variations in
software and hardware configurations. You may be able to resolve any
of these issues by troubleshooting the specific problems that occur,
but compatibility issues may limit the success of the restore of a
backup to dissimilar hardware.

Samenvatting
This article describes how to move an installation of Windows XP to
new, upgraded, or just different hardware. By using this information,
you can:
Migrate a working Windows XP operating system and your installed
programs to a different or more powerful computer in minimal downtime.
Replace a small system/boot disk drive with a larger system/boot disk
drive.
Restore a Windows backup from a malfunctioning computer to a different
computer for disaster recovery purposes.
Meer informatie
Windows Backup (Ntbackup.exe) can handle differences in hardware
configuration information between computers and maintain critical
registry entries that are unique to the computer to which you are
migrating information. This capability means that you can migrate to
new hardware by performing a full backup of the source computer and
then restoring the backup over a fresh installation of Windows XP on
the destination computer.

Ntbackup.exe handles restore operations in the registry by first
querying the following registry key:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\BackupRestore\KeysNotToRestore

This registry key indicates to Ntbackup.exe that certain registry keys
under the HKEY_LOCAL_MACHINE\SYSTEM key should not be overwritten when
files are restored.

An entry that ends with a backslash (\) indicates that a key is
protected and that any keys or values under that key should not be
restored. If the entry ends with a backslash and an asterisk (\*), all
subkeys are "merged." In this situation, "merged" means comparing the
start values of the keys in the backup set with the start values that
exist in the current registry, to determine the correct key to
restore.

If the value of the key on the backup set has a lower start value, the
backup key takes precedence. If the value of the key in the current
registry has a lower start value, the current key takes precedence.
This process ensures that all services and devices start correctly
after a "system state" restoration, even on dissimilar hardware.

For example: If the value of the following key on the backup set has a
lower start value, the backup key takes precedence:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Servic es\Dhcp

If the value of the same key in the current registry has a lower start
value than the key you want to restore, the current key takes
precedence.
Original System New System: Before Restore After
Restore

================================================== ======================
DHCP Running: YES NO YES
DHCP Running: NO YES YES
DHCP Running: NO NO NO
After the computer successfully restarts, Windows Plug and Play takes
care of any minor differences in hardware configuration.
The Factors to Consider Before You Use This Procedure
Drive Letters and the %SystemRoot% Folder
For a complete migration to work correctly, the %SystemRoot% folder
(the Windows folder in Windows XP) and the drive letters for any
(target) volumes that contain a system-state component must be the
same on both the source computer and the destination computer. This
means that if the source computer has, for example, Windows XP
Professional installed in the C:\Windows folder and has Active
Directory (NTDS) and SYSVOL on separate drives, drive D and drive E
respectively, the destination computer must have Windows XP
pre-installed in a C:\Windows folder and contain drives D and E before
the restore operation can succeed.
Hardware Abstraction Layer (HAL)
The HALs on both of the computers should be the same. This means that
the source and destination computers should be using the same HAL type
to achieve favorable results. Although this is not a requirement, the
computer may not perform migration properly if the HALs do not match.

To determine the type of HAL that you are using on each computer:
Click Start , click Control Panel , and then double-click System .
On the Hardware tab, click Device Manager , and then view the listing
under Computer . Possible values for the system description and the
associated HAL include:
ACPI Multiprocessor PC = Halmacpi.dll
ACPI Uniprocessor PC = Halaacpi.dll
Advanced Configuration and Power Interface (ACPI) PC = Halacpi.dll
MPS Multiprocessor PC = Halmps.dll
MPS Uniprocessor PC = Halapic.dll
Standard PC = Hal.dll
Compaq SystemPro Multiprocessor or 100% Compatible = Halsp.dll

The Windows\Repair Folder
The Windows\Repair folder that contains your source computer hardware
and software configuration files and the Setup.log file may not be
valid for the new hardware on the destination computer to which you
restored them. You should perform an in-place upgrade on the
destination computer to update these files so that you can make the
appropriate repairs in the future if necessary.
NTFS Volumes
You may need to start special filter drivers before you can restore
files that contain reparse points to NTFS volumes. This means that
before you can restore these types of files, you need to restart the
computer after you restore the operating system. Examples of these
types of files include Remote Installation Services (RIS) images that
rely on Single Instance Storage (SIS), Remote Storage Server (RSS)
files that you are restoring to managed volumes, or other third-party
services that use reparse points and require filter drivers.
The Procedure for Moving a Windows Installation
On the destination computer, perform a new installation of Windows,
using the product type that matches that of the source computer.
Ensure that the drive letter and %SystemRoot% folder names match those
on the source computer.
Using Disk Management, create, format, and assign drive letters to any
additional volumes that may be required to hold a system-state
component (for example, SYSVOL, Active Directory, or Active Directory
Log files). Ensure that all drive letters match those on the source
computer. For additional information about drive letter assignments,,
click the article number below to view the article in the Microsoft
Knowledge Base:
307844 HOW TO: Change Drive Letter Assignments in Windows XP

For additional information about drive letter assignments,, click the
article number below to view the article in the Microsoft Knowledge
Base: On the source computer, log on as Administrator, and then stop
all the non-essential services that you normally stop before
performing a backup.
For additional information about drive letter assignments,, click the
article number below to view the article in the Microsoft Knowledge
Base: Using Ntbackup.exe, back up the system\boot volume, the system
state, and associated NTDS and SYSVOL volumes, if applicable. For
additional information about how to perform a backup, click the
article number below to view the article in the Microsoft Knowledge
Base:
308422 HOW TO: Use Backup to Back Up Files and Folders on Your
Computer

For additional information about drive letter assignments,, click the
article number below to view the article in the Microsoft Knowledge
Base: On the destination computer, log on as Administrator. If the
system that you want to restore is a destination computer, you must
restart the computer, press F8 during startup, and then click
Directory Services Restore Mode before you log on as Administrator.
For additional information about drive letter assignments,, click the
article number below to view the article in the Microsoft Knowledge
Base: Start Ntbackup.exe, click Options on the Tools menu, click the
Restore tab, and then click Always replace the file on my computer .
Restore the system\boot volume, the system state, and associated
volumes from the backup that you performed previously. Make sure that
you select the option to restore them to "original location" in the
backup program. For additional information about how to restore, click
the article number below to view the article in the Microsoft
Knowledge Base:
309340 HOW TO: Use Backup to Restore Files and Folders on Your
Computer

NOTE : To have access to all removable media (tape or magneto-optic
[MO] disk) from the source computer after the full system restore is
complete, you must also click Restore Removable Storage Database under
Advanced before you begin the restore.


For additional information about drive letter assignments,, click the
article number below to view the article in the Microsoft Knowledge
Base: After the full restoration finishes, and before you restart the
destination computer, make sure that the computer is disconnected from
the network, to avoid conflicts.
For additional information about drive letter assignments,, click the
article number below to view the article in the Microsoft Knowledge
Base: Restart the computer.
If the computer does not restart after restoration because of HAL
mismatches, you can start from the Windows installation disk to
perform an in-place installation or repair. This type of repair occurs
after you accept the licensing agreement, and Setup searches for
previous versions to repair. When the installation that is damaged or
needs repair is found, press R to repair the selected installation.
Setup re-enumerates your computer's hardware (including the HAL) and
performs an in-place upgrade while maintaining your programs and user
settings. This also refreshes the %SystemRoot%\Repair folder with
accurate information that you can use for normal repairs.
If the computer does restart after the restoration, log on as
Administrator and initiate an in-place upgrade by running Winnt32.exe
from the i386 folder on the Windows CD-ROM. This refreshes the
Setup.log and registry files in the %SystemRoot%\Repair folder, and
ensures that the proper HAL is in use.
Note that in Microsoft Windows NT 4.0, user profiles are stored as a
subfolder of the %SystemRoot%\Profiles folder. In Windows XP, if the
installation is an upgrade, the existing profile path continues to be
used. In new Windows XP installations, a Documents and Settings folder
is created on the same volume as the Windows XP installation, to hold
user profiles. If the original system was an upgrade from Windows NT,
the original profiles will be used after the restore. However, if an
in-place upgrade is performed, you may need to change the profiles'
path in the registry back to %SystemRoot%\Profiles by modifying the
keys under the following path:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows
NT\CurrentVersion\ProfileList

For additional information about drive letter assignments,, click the
article number below to view the article in the Microsoft Knowledge
Base: After the upgrade is finished and you are certain that
everything works, you can remove the source (original) computer from
the network and connect the destination (new) computer in its place.
NOTE : The difference between the time of the backup and the time of
the restoration to the new computer may affect the machine account on
the domain controller. You may have to join a workgroup first, and
then rejoin the domain.

For additional information about re-activation after the restore,
click the article number below to view the article in the Microsoft
Knowledge Base:
305356 Windows XP Prompts You to Re-activate After You Restore Your
Computer

For information about how to install Ntbackup on a computer that runs
Windows XP Home Edition, see the following article in the Microsoft
Knowledge Base:
302894 HOW TO: Install Backup from the Windows XP Home Edition CD-ROM



Additional query words: stop 0x79 pnp transfer new hard drive

Keywords: kbenv kbinfo kbsetup KB314070
Technology: kbWinXPHome kbWinXPHomeSearch kbWinXPPro kbWinXPProSearch
kbWinXPSearch



--------------------------------------------------------------------------------

© Microsoft Corporation. All rights reserved."


--
(tm)
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
XP Pro: Won't Change Read Only Property clintonG General XP issues or comments 10 March 23rd 05 01:19 AM
Burning "read only" vs "Non read only" CD's Loring Hutchinson New Users to Windows XP 2 October 6th 04 04:28 AM
Can't read data CDs JPasternak Hardware and Windows XP 3 August 23rd 04 02:59 PM
Harddisks: Seek, Read, Write, Read, Write, Slow ? Skybuck Flying Hardware and Windows XP 20 July 23rd 04 05:16 AM
Harddisks: Seek, Read, Write, Read, Write, Slow ? Skybuck Flying Hardware and Windows XP 57 July 23rd 04 02:41 AM






All times are GMT +1. The time now is 10:22 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 PCbanter.
The comments are property of their posters.