If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#16
|
|||
|
|||
missing two r/w cd hardware devices that were pre assigned ear
I am sorry that you do not want to hear Upper and Lower filters but Code 31 that you
are receiving is the following and use the manual repair and not the automated Code 31 http://support.microsoft.com/default...b;en-us;314060 -- Peter Please Reply to Newsgroup for the benefit of others Requests for assistance by email can not and will not be acknowledged. "Sysu" wrote in message ... I have this problem also after uninstalling game software. In Device manager, it show DVD/CD-ROM and under that Multimedia Audio controller with an exclamation point by both. But when I update the driver, it installs drivers for SoundMax digital audio and places Multimedia Audio Controller in Sound devices. DVD/CD-ROM disappears from Device Manager and still not able to use CD/Rom/Dvd. Steps I have already taken: 1.) No upper/lower filters in the Registry that is so heavily floating as a solution. 2.) Cdgone did not work 3.) Microsoft's Fix it said it could not detect 4.) I checked my drivers in system 32 and two that are shown in driver details of IDE ATA ATAPI and Primary IDE channel (have no Second primary channel showing) are not in C:/Windows/System32/Drivers/ storprop.dll(primary) and pciidex.sys. I was told that senfilt.sys should not be in system 32. At one point it was not there but in the registry. I have not installed the driver for Multimedia Digital Audio driver. I did the add hardware wizard and it said 'Windows cannot load the drivers for this device(DVD/CD-ROM) Code 31. In my registry by CDROM in two places are two terms I don't understand. INITIALFAIL(by reg.key for deleting filters) and AutoRunDisable(by cdrom.sys) How can I get the drivers for DVD/CD-ROM to load and not in concert with Multimedia Audio Controller that installs SoundMax drivers for sound ONLY. "Rich Barry" wrote: Don, from what you said if you open MyComputer you see the C, D but not the E drive Icon. I would try right clicking MyComputerselect PropertiesHardwareDevice ManagerDvd/Cdrom Drives. Click on the plus sign and you should see two entries for your cdrw drives. If there rt click on each one and choose Uninstall. Restart your Computer and let WinXP reinstall the drives. "ragsy" mrsragsy wrote in message ... Hello; I went to look at what I had done so far and I noticed an error specifying missing hardware devices but the drivers for those locations appeared ok. (drive's b: & c. besides doing a total restore is there any way to reinsert those two missing hardware icons back so I can use them ? thank you -- mrtigre |
Ads |
#17
|
|||
|
|||
missing two r/w cd hardware devices that were pre assigned ear
I am sorry that you do not want to hear Upper and Lower filters but Code 31 that you
are receiving is the following and use the manual repair and not the automated Code 31 http://support.microsoft.com/default...b;en-us;314060 -- Peter Please Reply to Newsgroup for the benefit of others Requests for assistance by email can not and will not be acknowledged. "Sysu" wrote in message ... I have this problem also after uninstalling game software. In Device manager, it show DVD/CD-ROM and under that Multimedia Audio controller with an exclamation point by both. But when I update the driver, it installs drivers for SoundMax digital audio and places Multimedia Audio Controller in Sound devices. DVD/CD-ROM disappears from Device Manager and still not able to use CD/Rom/Dvd. Steps I have already taken: 1.) No upper/lower filters in the Registry that is so heavily floating as a solution. 2.) Cdgone did not work 3.) Microsoft's Fix it said it could not detect 4.) I checked my drivers in system 32 and two that are shown in driver details of IDE ATA ATAPI and Primary IDE channel (have no Second primary channel showing) are not in C:/Windows/System32/Drivers/ storprop.dll(primary) and pciidex.sys. I was told that senfilt.sys should not be in system 32. At one point it was not there but in the registry. I have not installed the driver for Multimedia Digital Audio driver. I did the add hardware wizard and it said 'Windows cannot load the drivers for this device(DVD/CD-ROM) Code 31. In my registry by CDROM in two places are two terms I don't understand. INITIALFAIL(by reg.key for deleting filters) and AutoRunDisable(by cdrom.sys) How can I get the drivers for DVD/CD-ROM to load and not in concert with Multimedia Audio Controller that installs SoundMax drivers for sound ONLY. "Rich Barry" wrote: Don, from what you said if you open MyComputer you see the C, D but not the E drive Icon. I would try right clicking MyComputerselect PropertiesHardwareDevice ManagerDvd/Cdrom Drives. Click on the plus sign and you should see two entries for your cdrw drives. If there rt click on each one and choose Uninstall. Restart your Computer and let WinXP reinstall the drives. "ragsy" mrsragsy wrote in message ... Hello; I went to look at what I had done so far and I noticed an error specifying missing hardware devices but the drivers for those locations appeared ok. (drive's b: & c. besides doing a total restore is there any way to reinsert those two missing hardware icons back so I can use them ? thank you -- mrtigre |
#18
|
|||
|
|||
missing two r/w cd hardware devices that were pre assigned ear
Sad but true. When I click the arrows it says: Unknown and n/a and that is
all I get. I copied the info if it will aid you in helping me, it is kind of long so bear with me. It is the Drive config. and boot sequence in bios and what it shows. BIOS Drive Configuration Diskette Drive A 3.5nch, 1.44mb Primary Master Drive Hard Drive (WDC WD400EB-75CPF0) '' Slave Drive OFF (model unknown) Secondary Master Drive OFF " " " Slave Drive OFF " " IDE Drive UDMA ON Boot Sequence CD-Rom device (not installed) Floppy Device ON Hard Disk Drive C ( has a check in front of it) Hope this is pertinent info. I am a novice at this. "Tim Meddick" wrote: Something is definitely getting lost in translation here!... If indeed, as you say, BOTH Primary AND Secondary IDE controller channels are OFF in the BIOS then certainly you would NOT* be booting from the hard drive! The reason there is this setting in the BIOS is for troubleshooting and certainly, you should be able to change their setting.... *(Except, possibly, if you are using SATA HDs) == Cheers, Tim Meddick, Peckham, London. :-) "Sysu" wrote in message ... Thanks for your response glee. I hope you read my first post. It included everything I had tried except bios. In bios (Drive Config.), Primary and Secondary are set at OFF. .... clipped . |
#19
|
|||
|
|||
missing two r/w cd hardware devices that were pre assigned ear
Sad but true. When I click the arrows it says: Unknown and n/a and that is
all I get. I copied the info if it will aid you in helping me, it is kind of long so bear with me. It is the Drive config. and boot sequence in bios and what it shows. BIOS Drive Configuration Diskette Drive A 3.5nch, 1.44mb Primary Master Drive Hard Drive (WDC WD400EB-75CPF0) '' Slave Drive OFF (model unknown) Secondary Master Drive OFF " " " Slave Drive OFF " " IDE Drive UDMA ON Boot Sequence CD-Rom device (not installed) Floppy Device ON Hard Disk Drive C ( has a check in front of it) Hope this is pertinent info. I am a novice at this. "Tim Meddick" wrote: Something is definitely getting lost in translation here!... If indeed, as you say, BOTH Primary AND Secondary IDE controller channels are OFF in the BIOS then certainly you would NOT* be booting from the hard drive! The reason there is this setting in the BIOS is for troubleshooting and certainly, you should be able to change their setting.... *(Except, possibly, if you are using SATA HDs) == Cheers, Tim Meddick, Peckham, London. :-) "Sysu" wrote in message ... Thanks for your response glee. I hope you read my first post. It included everything I had tried except bios. In bios (Drive Config.), Primary and Secondary are set at OFF. .... clipped . |
#20
|
|||
|
|||
missing two r/w cd hardware devices that were pre assigned ear
Thanks for your response Peter. But if you read my original post, I tried
everything mentioned in the threads . Code 31 is what I am getting. Windows cannot load the drivers. and Bios says CD-rom is not installed. I found no upper or lower filters mentioned in the reg. key to look for and delete. I am a novice at this and not sure about the SATA HD you mentioned. "Peter Foldes" wrote: I am sorry that you do not want to hear Upper and Lower filters but Code 31 that you are receiving is the following and use the manual repair and not the automated Code 31 http://support.microsoft.com/default...b;en-us;314060 -- Peter Please Reply to Newsgroup for the benefit of others Requests for assistance by email can not and will not be acknowledged. "Sysu" wrote in message ... I have this problem also after uninstalling game software. In Device manager, it show DVD/CD-ROM and under that Multimedia Audio controller with an exclamation point by both. But when I update the driver, it installs drivers for SoundMax digital audio and places Multimedia Audio Controller in Sound devices. DVD/CD-ROM disappears from Device Manager and still not able to use CD/Rom/Dvd. Steps I have already taken: 1.) No upper/lower filters in the Registry that is so heavily floating as a solution. 2.) Cdgone did not work 3.) Microsoft's Fix it said it could not detect 4.) I checked my drivers in system 32 and two that are shown in driver details of IDE ATA ATAPI and Primary IDE channel (have no Second primary channel showing) are not in C:/Windows/System32/Drivers/ storprop.dll(primary) and pciidex.sys. I was told that senfilt.sys should not be in system 32. At one point it was not there but in the registry. I have not installed the driver for Multimedia Digital Audio driver. I did the add hardware wizard and it said 'Windows cannot load the drivers for this device(DVD/CD-ROM) Code 31. In my registry by CDROM in two places are two terms I don't understand. INITIALFAIL(by reg.key for deleting filters) and AutoRunDisable(by cdrom.sys) How can I get the drivers for DVD/CD-ROM to load and not in concert with Multimedia Audio Controller that installs SoundMax drivers for sound ONLY. "Rich Barry" wrote: Don, from what you said if you open MyComputer you see the C, D but not the E drive Icon. I would try right clicking MyComputerselect PropertiesHardwareDevice ManagerDvd/Cdrom Drives. Click on the plus sign and you should see two entries for your cdrw drives. If there rt click on each one and choose Uninstall. Restart your Computer and let WinXP reinstall the drives. "ragsy" mrsragsy wrote in message ... Hello; I went to look at what I had done so far and I noticed an error specifying missing hardware devices but the drivers for those locations appeared ok. (drive's b: & c. besides doing a total restore is there any way to reinsert those two missing hardware icons back so I can use them ? thank you -- mrtigre . |
#21
|
|||
|
|||
missing two r/w cd hardware devices that were pre assigned ear
Thanks for your response Peter. But if you read my original post, I tried
everything mentioned in the threads . Code 31 is what I am getting. Windows cannot load the drivers. and Bios says CD-rom is not installed. I found no upper or lower filters mentioned in the reg. key to look for and delete. I am a novice at this and not sure about the SATA HD you mentioned. "Peter Foldes" wrote: I am sorry that you do not want to hear Upper and Lower filters but Code 31 that you are receiving is the following and use the manual repair and not the automated Code 31 http://support.microsoft.com/default...b;en-us;314060 -- Peter Please Reply to Newsgroup for the benefit of others Requests for assistance by email can not and will not be acknowledged. "Sysu" wrote in message ... I have this problem also after uninstalling game software. In Device manager, it show DVD/CD-ROM and under that Multimedia Audio controller with an exclamation point by both. But when I update the driver, it installs drivers for SoundMax digital audio and places Multimedia Audio Controller in Sound devices. DVD/CD-ROM disappears from Device Manager and still not able to use CD/Rom/Dvd. Steps I have already taken: 1.) No upper/lower filters in the Registry that is so heavily floating as a solution. 2.) Cdgone did not work 3.) Microsoft's Fix it said it could not detect 4.) I checked my drivers in system 32 and two that are shown in driver details of IDE ATA ATAPI and Primary IDE channel (have no Second primary channel showing) are not in C:/Windows/System32/Drivers/ storprop.dll(primary) and pciidex.sys. I was told that senfilt.sys should not be in system 32. At one point it was not there but in the registry. I have not installed the driver for Multimedia Digital Audio driver. I did the add hardware wizard and it said 'Windows cannot load the drivers for this device(DVD/CD-ROM) Code 31. In my registry by CDROM in two places are two terms I don't understand. INITIALFAIL(by reg.key for deleting filters) and AutoRunDisable(by cdrom.sys) How can I get the drivers for DVD/CD-ROM to load and not in concert with Multimedia Audio Controller that installs SoundMax drivers for sound ONLY. "Rich Barry" wrote: Don, from what you said if you open MyComputer you see the C, D but not the E drive Icon. I would try right clicking MyComputerselect PropertiesHardwareDevice ManagerDvd/Cdrom Drives. Click on the plus sign and you should see two entries for your cdrw drives. If there rt click on each one and choose Uninstall. Restart your Computer and let WinXP reinstall the drives. "ragsy" mrsragsy wrote in message ... Hello; I went to look at what I had done so far and I noticed an error specifying missing hardware devices but the drivers for those locations appeared ok. (drive's b: & c. besides doing a total restore is there any way to reinsert those two missing hardware icons back so I can use them ? thank you -- mrtigre . |
#22
|
|||
|
|||
missing two r/w cd hardware devices that were pre assigned ear
The hard drive model number you listed in your other reply he
WD400EB-75CPF0, is not a SATA drive, it is a 40GB Western Digital PATA drive (IDE connection). Your problem appears to be, as I stated in my original reply, that you do not have the secondary IDE channel enabled in the BIOS. -- Glen Ventura, MS MVP Oct. 2002 - Sept. 2009 A+ http://dts-l.net/ "Sysu" wrote in message ... Thanks for your response Peter. But if you read my original post, I tried everything mentioned in the threads . Code 31 is what I am getting. Windows cannot load the drivers. and Bios says CD-rom is not installed. I found no upper or lower filters mentioned in the reg. key to look for and delete. I am a novice at this and not sure about the SATA HD you mentioned. "Peter Foldes" wrote: I am sorry that you do not want to hear Upper and Lower filters but Code 31 that you are receiving is the following and use the manual repair and not the automated Code 31 http://support.microsoft.com/default...b;en-us;314060 -- Peter Please Reply to Newsgroup for the benefit of others Requests for assistance by email can not and will not be acknowledged. "Sysu" wrote in message ... I have this problem also after uninstalling game software. In Device manager, it show DVD/CD-ROM and under that Multimedia Audio controller with an exclamation point by both. But when I update the driver, it installs drivers for SoundMax digital audio and places Multimedia Audio Controller in Sound devices. DVD/CD-ROM disappears from Device Manager and still not able to use CD/Rom/Dvd. Steps I have already taken: 1.) No upper/lower filters in the Registry that is so heavily floating as a solution. 2.) Cdgone did not work 3.) Microsoft's Fix it said it could not detect 4.) I checked my drivers in system 32 and two that are shown in driver details of IDE ATA ATAPI and Primary IDE channel (have no Second primary channel showing) are not in C:/Windows/System32/Drivers/ storprop.dll(primary) and pciidex.sys. I was told that senfilt.sys should not be in system 32. At one point it was not there but in the registry. I have not installed the driver for Multimedia Digital Audio driver. I did the add hardware wizard and it said 'Windows cannot load the drivers for this device(DVD/CD-ROM) Code 31. In my registry by CDROM in two places are two terms I don't understand. INITIALFAIL(by reg.key for deleting filters) and AutoRunDisable(by cdrom.sys) How can I get the drivers for DVD/CD-ROM to load and not in concert with Multimedia Audio Controller that installs SoundMax drivers for sound ONLY. "Rich Barry" wrote: Don, from what you said if you open MyComputer you see the C, D but not the E drive Icon. I would try right clicking MyComputerselect PropertiesHardwareDevice ManagerDvd/Cdrom Drives. Click on the plus sign and you should see two entries for your cdrw drives. If there rt click on each one and choose Uninstall. Restart your Computer and let WinXP reinstall the drives. "ragsy" mrsragsy wrote in message ... Hello; I went to look at what I had done so far and I noticed an error specifying missing hardware devices but the drivers for those locations appeared ok. (drive's b: & c. besides doing a total restore is there any way to reinsert those two missing hardware icons back so I can use them ? thank you -- mrtigre . |
#23
|
|||
|
|||
missing two r/w cd hardware devices that were pre assigned ear
The hard drive model number you listed in your other reply he
WD400EB-75CPF0, is not a SATA drive, it is a 40GB Western Digital PATA drive (IDE connection). Your problem appears to be, as I stated in my original reply, that you do not have the secondary IDE channel enabled in the BIOS. -- Glen Ventura, MS MVP Oct. 2002 - Sept. 2009 A+ http://dts-l.net/ "Sysu" wrote in message ... Thanks for your response Peter. But if you read my original post, I tried everything mentioned in the threads . Code 31 is what I am getting. Windows cannot load the drivers. and Bios says CD-rom is not installed. I found no upper or lower filters mentioned in the reg. key to look for and delete. I am a novice at this and not sure about the SATA HD you mentioned. "Peter Foldes" wrote: I am sorry that you do not want to hear Upper and Lower filters but Code 31 that you are receiving is the following and use the manual repair and not the automated Code 31 http://support.microsoft.com/default...b;en-us;314060 -- Peter Please Reply to Newsgroup for the benefit of others Requests for assistance by email can not and will not be acknowledged. "Sysu" wrote in message ... I have this problem also after uninstalling game software. In Device manager, it show DVD/CD-ROM and under that Multimedia Audio controller with an exclamation point by both. But when I update the driver, it installs drivers for SoundMax digital audio and places Multimedia Audio Controller in Sound devices. DVD/CD-ROM disappears from Device Manager and still not able to use CD/Rom/Dvd. Steps I have already taken: 1.) No upper/lower filters in the Registry that is so heavily floating as a solution. 2.) Cdgone did not work 3.) Microsoft's Fix it said it could not detect 4.) I checked my drivers in system 32 and two that are shown in driver details of IDE ATA ATAPI and Primary IDE channel (have no Second primary channel showing) are not in C:/Windows/System32/Drivers/ storprop.dll(primary) and pciidex.sys. I was told that senfilt.sys should not be in system 32. At one point it was not there but in the registry. I have not installed the driver for Multimedia Digital Audio driver. I did the add hardware wizard and it said 'Windows cannot load the drivers for this device(DVD/CD-ROM) Code 31. In my registry by CDROM in two places are two terms I don't understand. INITIALFAIL(by reg.key for deleting filters) and AutoRunDisable(by cdrom.sys) How can I get the drivers for DVD/CD-ROM to load and not in concert with Multimedia Audio Controller that installs SoundMax drivers for sound ONLY. "Rich Barry" wrote: Don, from what you said if you open MyComputer you see the C, D but not the E drive Icon. I would try right clicking MyComputerselect PropertiesHardwareDevice ManagerDvd/Cdrom Drives. Click on the plus sign and you should see two entries for your cdrw drives. If there rt click on each one and choose Uninstall. Restart your Computer and let WinXP reinstall the drives. "ragsy" mrsragsy wrote in message ... Hello; I went to look at what I had done so far and I noticed an error specifying missing hardware devices but the drivers for those locations appeared ok. (drive's b: & c. besides doing a total restore is there any way to reinsert those two missing hardware icons back so I can use them ? thank you -- mrtigre . |
#24
|
|||
|
|||
missing two r/w cd hardware devices that were pre assigned ear
Yes, very pertinent. You have a PATA (IDE) hard drive, not a SATA
drive, and judging by the size (40GB) you probably don't have any SATA connections in that computer (a Dell probably). If it is a Dell, or some other OEM machine, the BIOS setup is likely modified by them, which makes it hard to tell you where in the BIOS setup you have to go to change the settings in order to enable both IDE channels and also to set them to Auto so they can automatically detect any attached drives. Someone must have gone into the BIOS setup at some time and accidentally disabled the channel....although I have also seen a strong electrical surge change BIOS settings. If you are not familiar with the BIOS setup or are uncomfortable working in it, find someone who is, to help you, or else take it to a competent computer tech to adjust the settings. If you want to try to do it yourself, we will need more info on what screens are available in the BIOS setup that you see. Some fields in the BIOS can be opened if you press Enter, others do not expand. There should be a Legend probably at the bottom of the screen, telling you what keys to use to navigate. -- Glen Ventura, MS MVP Oct. 2002 - Sept. 2009 A+ http://dts-l.net/ "Sysu" wrote in message ... Sad but true. When I click the arrows it says: Unknown and n/a and that is all I get. I copied the info if it will aid you in helping me, it is kind of long so bear with me. It is the Drive config. and boot sequence in bios and what it shows. BIOS Drive Configuration Diskette Drive A 3.5nch, 1.44mb Primary Master Drive Hard Drive (WDC WD400EB-75CPF0) '' Slave Drive OFF (model unknown) Secondary Master Drive OFF " " " Slave Drive OFF " " IDE Drive UDMA ON Boot Sequence CD-Rom device (not installed) Floppy Device ON Hard Disk Drive C ( has a check in front of it) Hope this is pertinent info. I am a novice at this. "Tim Meddick" wrote: Something is definitely getting lost in translation here!... If indeed, as you say, BOTH Primary AND Secondary IDE controller channels are OFF in the BIOS then certainly you would NOT* be booting from the hard drive! The reason there is this setting in the BIOS is for troubleshooting and certainly, you should be able to change their setting.... *(Except, possibly, if you are using SATA HDs) == Cheers, Tim Meddick, Peckham, London. :-) "Sysu" wrote in message ... Thanks for your response glee. I hope you read my first post. It included everything I had tried except bios. In bios (Drive Config.), Primary and Secondary are set at OFF. .... clipped . |
#25
|
|||
|
|||
missing two r/w cd hardware devices that were pre assigned ear
Yes, very pertinent. You have a PATA (IDE) hard drive, not a SATA
drive, and judging by the size (40GB) you probably don't have any SATA connections in that computer (a Dell probably). If it is a Dell, or some other OEM machine, the BIOS setup is likely modified by them, which makes it hard to tell you where in the BIOS setup you have to go to change the settings in order to enable both IDE channels and also to set them to Auto so they can automatically detect any attached drives. Someone must have gone into the BIOS setup at some time and accidentally disabled the channel....although I have also seen a strong electrical surge change BIOS settings. If you are not familiar with the BIOS setup or are uncomfortable working in it, find someone who is, to help you, or else take it to a competent computer tech to adjust the settings. If you want to try to do it yourself, we will need more info on what screens are available in the BIOS setup that you see. Some fields in the BIOS can be opened if you press Enter, others do not expand. There should be a Legend probably at the bottom of the screen, telling you what keys to use to navigate. -- Glen Ventura, MS MVP Oct. 2002 - Sept. 2009 A+ http://dts-l.net/ "Sysu" wrote in message ... Sad but true. When I click the arrows it says: Unknown and n/a and that is all I get. I copied the info if it will aid you in helping me, it is kind of long so bear with me. It is the Drive config. and boot sequence in bios and what it shows. BIOS Drive Configuration Diskette Drive A 3.5nch, 1.44mb Primary Master Drive Hard Drive (WDC WD400EB-75CPF0) '' Slave Drive OFF (model unknown) Secondary Master Drive OFF " " " Slave Drive OFF " " IDE Drive UDMA ON Boot Sequence CD-Rom device (not installed) Floppy Device ON Hard Disk Drive C ( has a check in front of it) Hope this is pertinent info. I am a novice at this. "Tim Meddick" wrote: Something is definitely getting lost in translation here!... If indeed, as you say, BOTH Primary AND Secondary IDE controller channels are OFF in the BIOS then certainly you would NOT* be booting from the hard drive! The reason there is this setting in the BIOS is for troubleshooting and certainly, you should be able to change their setting.... *(Except, possibly, if you are using SATA HDs) == Cheers, Tim Meddick, Peckham, London. :-) "Sysu" wrote in message ... Thanks for your response glee. I hope you read my first post. It included everything I had tried except bios. In bios (Drive Config.), Primary and Secondary are set at OFF. .... clipped . |
#26
|
|||
|
|||
missing two r/w cd hardware devices that were pre assigned ear
Thanks for the explanation. As I said I am a novice at some of this. You hit
the nail on the head. Another informative pc person said the same thing. So, since this PC is about 7 yrs. old, it may be time to get another. As far as someone having inadvertently tampered with the bios and made mistakes, it was probably me. I got the Floppy Disk on but not the CD-Rom. Neither of the Primary or Secondary. Now my PC only boots to the Hard Drive. I have been searching for advice about this problem in most all the forums and so much different advice is out there. It all seems to fit to solve my problem (cuz it was solving a lot of others) and following some of it made my problems worse. thanks ever so much and Be Blessed. "glee" wrote: Yes, very pertinent. You have a PATA (IDE) hard drive, not a SATA drive, and judging by the size (40GB) you probably don't have any SATA connections in that computer (a Dell probably). If it is a Dell, or some other OEM machine, the BIOS setup is likely modified by them, which makes it hard to tell you where in the BIOS setup you have to go to change the settings in order to enable both IDE channels and also to set them to Auto so they can automatically detect any attached drives. Someone must have gone into the BIOS setup at some time and accidentally disabled the channel....although I have also seen a strong electrical surge change BIOS settings. If you are not familiar with the BIOS setup or are uncomfortable working in it, find someone who is, to help you, or else take it to a competent computer tech to adjust the settings. If you want to try to do it yourself, we will need more info on what screens are available in the BIOS setup that you see. Some fields in the BIOS can be opened if you press Enter, others do not expand. There should be a Legend probably at the bottom of the screen, telling you what keys to use to navigate. -- Glen Ventura, MS MVP Oct. 2002 - Sept. 2009 A+ http://dts-l.net/ "Sysu" wrote in message ... Sad but true. When I click the arrows it says: Unknown and n/a and that is all I get. I copied the info if it will aid you in helping me, it is kind of long so bear with me. It is the Drive config. and boot sequence in bios and what it shows. BIOS Drive Configuration Diskette Drive A 3.5nch, 1.44mb Primary Master Drive Hard Drive (WDC WD400EB-75CPF0) '' Slave Drive OFF (model unknown) Secondary Master Drive OFF " " " Slave Drive OFF " " IDE Drive UDMA ON Boot Sequence CD-Rom device (not installed) Floppy Device ON Hard Disk Drive C ( has a check in front of it) Hope this is pertinent info. I am a novice at this. "Tim Meddick" wrote: Something is definitely getting lost in translation here!... If indeed, as you say, BOTH Primary AND Secondary IDE controller channels are OFF in the BIOS then certainly you would NOT* be booting from the hard drive! The reason there is this setting in the BIOS is for troubleshooting and certainly, you should be able to change their setting.... *(Except, possibly, if you are using SATA HDs) == Cheers, Tim Meddick, Peckham, London. :-) "Sysu" wrote in message ... Thanks for your response glee. I hope you read my first post. It included everything I had tried except bios. In bios (Drive Config.), Primary and Secondary are set at OFF. .... clipped . . |
#27
|
|||
|
|||
missing two r/w cd hardware devices that were pre assigned ear
Thanks for the explanation. As I said I am a novice at some of this. You hit
the nail on the head. Another informative pc person said the same thing. So, since this PC is about 7 yrs. old, it may be time to get another. As far as someone having inadvertently tampered with the bios and made mistakes, it was probably me. I got the Floppy Disk on but not the CD-Rom. Neither of the Primary or Secondary. Now my PC only boots to the Hard Drive. I have been searching for advice about this problem in most all the forums and so much different advice is out there. It all seems to fit to solve my problem (cuz it was solving a lot of others) and following some of it made my problems worse. thanks ever so much and Be Blessed. "glee" wrote: Yes, very pertinent. You have a PATA (IDE) hard drive, not a SATA drive, and judging by the size (40GB) you probably don't have any SATA connections in that computer (a Dell probably). If it is a Dell, or some other OEM machine, the BIOS setup is likely modified by them, which makes it hard to tell you where in the BIOS setup you have to go to change the settings in order to enable both IDE channels and also to set them to Auto so they can automatically detect any attached drives. Someone must have gone into the BIOS setup at some time and accidentally disabled the channel....although I have also seen a strong electrical surge change BIOS settings. If you are not familiar with the BIOS setup or are uncomfortable working in it, find someone who is, to help you, or else take it to a competent computer tech to adjust the settings. If you want to try to do it yourself, we will need more info on what screens are available in the BIOS setup that you see. Some fields in the BIOS can be opened if you press Enter, others do not expand. There should be a Legend probably at the bottom of the screen, telling you what keys to use to navigate. -- Glen Ventura, MS MVP Oct. 2002 - Sept. 2009 A+ http://dts-l.net/ "Sysu" wrote in message ... Sad but true. When I click the arrows it says: Unknown and n/a and that is all I get. I copied the info if it will aid you in helping me, it is kind of long so bear with me. It is the Drive config. and boot sequence in bios and what it shows. BIOS Drive Configuration Diskette Drive A 3.5nch, 1.44mb Primary Master Drive Hard Drive (WDC WD400EB-75CPF0) '' Slave Drive OFF (model unknown) Secondary Master Drive OFF " " " Slave Drive OFF " " IDE Drive UDMA ON Boot Sequence CD-Rom device (not installed) Floppy Device ON Hard Disk Drive C ( has a check in front of it) Hope this is pertinent info. I am a novice at this. "Tim Meddick" wrote: Something is definitely getting lost in translation here!... If indeed, as you say, BOTH Primary AND Secondary IDE controller channels are OFF in the BIOS then certainly you would NOT* be booting from the hard drive! The reason there is this setting in the BIOS is for troubleshooting and certainly, you should be able to change their setting.... *(Except, possibly, if you are using SATA HDs) == Cheers, Tim Meddick, Peckham, London. :-) "Sysu" wrote in message ... Thanks for your response glee. I hope you read my first post. It included everything I had tried except bios. In bios (Drive Config.), Primary and Secondary are set at OFF. .... clipped . . |
#28
|
|||
|
|||
missing two r/w cd hardware devices that were pre assigned ear
Since my cdrom drive is not working, I went to Microsoft's website and
downloaded a reinstalling of Windows XP on formatted Floppy Disks (6). But it said I would need the XP installation CD to complete the process. Microsoft should think, If I have to reinstall Windows XP via floppy disk, how in the heck can I use the installation CD at the end? If I had the CD I would not need to download a new installation via floppy disk. If you or someone you know can help me get around this minor inconvenience please post it. I will give this solution one more chance before getting indebted for another computer. Thanks again "glee" wrote: Yes, very pertinent. You have a PATA (IDE) hard drive, not a SATA drive, and judging by the size (40GB) you probably don't have any SATA connections in that computer (a Dell probably). If it is a Dell, or some other OEM machine, the BIOS setup is likely modified by them, which makes it hard to tell you where in the BIOS setup you have to go to change the settings in order to enable both IDE channels and also to set them to Auto so they can automatically detect any attached drives. Someone must have gone into the BIOS setup at some time and accidentally disabled the channel....although I have also seen a strong electrical surge change BIOS settings. If you are not familiar with the BIOS setup or are uncomfortable working in it, find someone who is, to help you, or else take it to a competent computer tech to adjust the settings. If you want to try to do it yourself, we will need more info on what screens are available in the BIOS setup that you see. Some fields in the BIOS can be opened if you press Enter, others do not expand. There should be a Legend probably at the bottom of the screen, telling you what keys to use to navigate. -- Glen Ventura, MS MVP Oct. 2002 - Sept. 2009 A+ http://dts-l.net/ "Sysu" wrote in message ... Sad but true. When I click the arrows it says: Unknown and n/a and that is all I get. I copied the info if it will aid you in helping me, it is kind of long so bear with me. It is the Drive config. and boot sequence in bios and what it shows. BIOS Drive Configuration Diskette Drive A 3.5nch, 1.44mb Primary Master Drive Hard Drive (WDC WD400EB-75CPF0) '' Slave Drive OFF (model unknown) Secondary Master Drive OFF " " " Slave Drive OFF " " IDE Drive UDMA ON Boot Sequence CD-Rom device (not installed) Floppy Device ON Hard Disk Drive C ( has a check in front of it) Hope this is pertinent info. I am a novice at this. "Tim Meddick" wrote: Something is definitely getting lost in translation here!... If indeed, as you say, BOTH Primary AND Secondary IDE controller channels are OFF in the BIOS then certainly you would NOT* be booting from the hard drive! The reason there is this setting in the BIOS is for troubleshooting and certainly, you should be able to change their setting.... *(Except, possibly, if you are using SATA HDs) == Cheers, Tim Meddick, Peckham, London. :-) "Sysu" wrote in message ... Thanks for your response glee. I hope you read my first post. It included everything I had tried except bios. In bios (Drive Config.), Primary and Secondary are set at OFF. .... clipped . . |
#29
|
|||
|
|||
missing two r/w cd hardware devices that were pre assigned ear
Since my cdrom drive is not working, I went to Microsoft's website and
downloaded a reinstalling of Windows XP on formatted Floppy Disks (6). But it said I would need the XP installation CD to complete the process. Microsoft should think, If I have to reinstall Windows XP via floppy disk, how in the heck can I use the installation CD at the end? If I had the CD I would not need to download a new installation via floppy disk. If you or someone you know can help me get around this minor inconvenience please post it. I will give this solution one more chance before getting indebted for another computer. Thanks again "glee" wrote: Yes, very pertinent. You have a PATA (IDE) hard drive, not a SATA drive, and judging by the size (40GB) you probably don't have any SATA connections in that computer (a Dell probably). If it is a Dell, or some other OEM machine, the BIOS setup is likely modified by them, which makes it hard to tell you where in the BIOS setup you have to go to change the settings in order to enable both IDE channels and also to set them to Auto so they can automatically detect any attached drives. Someone must have gone into the BIOS setup at some time and accidentally disabled the channel....although I have also seen a strong electrical surge change BIOS settings. If you are not familiar with the BIOS setup or are uncomfortable working in it, find someone who is, to help you, or else take it to a competent computer tech to adjust the settings. If you want to try to do it yourself, we will need more info on what screens are available in the BIOS setup that you see. Some fields in the BIOS can be opened if you press Enter, others do not expand. There should be a Legend probably at the bottom of the screen, telling you what keys to use to navigate. -- Glen Ventura, MS MVP Oct. 2002 - Sept. 2009 A+ http://dts-l.net/ "Sysu" wrote in message ... Sad but true. When I click the arrows it says: Unknown and n/a and that is all I get. I copied the info if it will aid you in helping me, it is kind of long so bear with me. It is the Drive config. and boot sequence in bios and what it shows. BIOS Drive Configuration Diskette Drive A 3.5nch, 1.44mb Primary Master Drive Hard Drive (WDC WD400EB-75CPF0) '' Slave Drive OFF (model unknown) Secondary Master Drive OFF " " " Slave Drive OFF " " IDE Drive UDMA ON Boot Sequence CD-Rom device (not installed) Floppy Device ON Hard Disk Drive C ( has a check in front of it) Hope this is pertinent info. I am a novice at this. "Tim Meddick" wrote: Something is definitely getting lost in translation here!... If indeed, as you say, BOTH Primary AND Secondary IDE controller channels are OFF in the BIOS then certainly you would NOT* be booting from the hard drive! The reason there is this setting in the BIOS is for troubleshooting and certainly, you should be able to change their setting.... *(Except, possibly, if you are using SATA HDs) == Cheers, Tim Meddick, Peckham, London. :-) "Sysu" wrote in message ... Thanks for your response glee. I hope you read my first post. It included everything I had tried except bios. In bios (Drive Config.), Primary and Secondary are set at OFF. .... clipped . . |
#30
|
|||
|
|||
missing two r/w cd hardware devices that were pre assigned ear
As "glee" keeps on saying, we are not talking about Primary / Secondary Hard-drives
(as you printed out a copy of those settings as it appeared in your BIOS in an earlier post) but rather, we are talking about IDE CHANNELS! IDE controllers often have a setting in the BIOS that enables you to choose whether to use the PRIMARY or SECONDARY or even BOTH of the channels (the IDE controller having two channels). The reason (I believe) that "glee" and I think it may be this setting, is that the MASTER HD is usually connected to the PRIMARY IDE channel and the CD/DVD drive to the SECONDARY channel - thus - if someone tampered with the setting and set it to USE PRIMARY ONLY - then the CD/DVD device would not be working. This is just one theory of quite a few possible causes - another of which could be - as unlikely as it sounds - that your cd/dvd drive failed at the exact same time as all this happened. But you have to start somewhere, and seeing if there is a setting in your BIOS that enables / disables the secondary IDE channel (either with an "on" or "off" setting or, more commonly, a setting that lets you choose either "primary", "secondary" or "both" - where it should be set to "both" you may have accidentally set it to "primary" thereby inadvertently turning off the other channel that carries the cd/dvd drive). One more thing - the use of floppy "installation" disks will do very little for you. They are meant only to start up a PC, ready for installation from an XP installation CD, when that PC cannot BOOT from the cd/dvd for some reason. However, I still think it may be possible to re-format your HD with the floppy set - thereby wiping out all the data off your hard drive for good - please beware of this... == Cheers, Tim Meddick, Peckham, London. :-) "Sysu" wrote in message ... Thanks for your response Peter. But if you read my original post, I tried everything mentioned in the threads . Code 31 is what I am getting. Windows cannot load the drivers. and Bios says CD-rom is not installed. I found no upper or lower filters mentioned in the reg. key to look for and delete. I am a novice at this and not sure about the SATA HD you mentioned. "Peter Foldes" wrote: I am sorry that you do not want to hear Upper and Lower filters but Code 31 that you are receiving is the following and use the manual repair and not the automated Code 31 http://support.microsoft.com/default...b;en-us;314060 -- Peter Please Reply to Newsgroup for the benefit of others Requests for assistance by email can not and will not be acknowledged. "Sysu" wrote in message ... I have this problem also after uninstalling game software. In Device manager, it show DVD/CD-ROM and under that Multimedia Audio controller with an exclamation point by both. But when I update the driver, it installs drivers for SoundMax digital audio and places Multimedia Audio Controller in Sound devices. DVD/CD-ROM disappears from Device Manager and still not able to use CD/Rom/Dvd. Steps I have already taken: 1.) No upper/lower filters in the Registry that is so heavily floating as a solution. 2.) Cdgone did not work 3.) Microsoft's Fix it said it could not detect 4.) I checked my drivers in system 32 and two that are shown in driver details of IDE ATA ATAPI and Primary IDE channel (have no Second primary channel showing) are not in C:/Windows/System32/Drivers/ storprop.dll(primary) and pciidex.sys. I was told that senfilt.sys should not be in system 32. At one point it was not there but in the registry. I have not installed the driver for Multimedia Digital Audio driver. I did the add hardware wizard and it said 'Windows cannot load the drivers for this device(DVD/CD-ROM) Code 31. In my registry by CDROM in two places are two terms I don't understand. INITIALFAIL(by reg.key for deleting filters) and AutoRunDisable(by cdrom.sys) How can I get the drivers for DVD/CD-ROM to load and not in concert with Multimedia Audio Controller that installs SoundMax drivers for sound ONLY. "Rich Barry" wrote: Don, from what you said if you open MyComputer you see the C, D but not the E drive Icon. I would try right clicking MyComputerselect PropertiesHardwareDevice ManagerDvd/Cdrom Drives. Click on the plus sign and you should see two entries for your cdrw drives. If there rt click on each one and choose Uninstall. Restart your Computer and let WinXP reinstall the drives. "ragsy" mrsragsy wrote in message ... Hello; I went to look at what I had done so far and I noticed an error specifying missing hardware devices but the drivers for those locations appeared ok. (drive's b: & c. besides doing a total restore is there any way to reinsert those two missing hardware icons back so I can use them ? thank you -- mrtigre . |
Thread Tools | |
Display Modes | |
|
|