A Windows XP help forum. PCbanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » PCbanter forum » Microsoft Windows XP » Windows XP Help and Support
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Boot Problem



 
 
Thread Tools Display Modes
  #1  
Old June 7th 07, 02:48 PM posted to microsoft.public.windowsxp.help_and_support
Bernie
external usenet poster
 
Posts: 35
Default Boot Problem

Hi I had a problem with the OS and repaired succesfully(?) with WIN XP using
the
CD Installation disc. Now my computer will not Boot up in Win XP. It gets to
the Windows Home page and reboots. It will not enter Safemode either. The
disc checks out ok and the same problem appears in another computer using the
same disc, and in the other computer you can see all files except where the
security was at the Administrator level.
Win XP says there isn't a problem with the disc so please can somebody tell
me why it will not boot up correctly? I have made a chkdsk c: /R it repaired
some errors but keeps rebooting. Can I turn off Auto Reboot outside of
windows?
Ads
  #2  
Old June 7th 07, 03:29 PM posted to microsoft.public.windowsxp.help_and_support
Mark L. Ferguson
external usenet poster
 
Posts: 82
Default Boot Problem

If it will not enter safe mode, it is not repaired. Did you run a Repair
after the successful chkdsk? If so, you probably have a damaged hard drive.

--
Mark L. Ferguson
..
"Bernie" wrote in message
news
Hi I had a problem with the OS and repaired succesfully(?) with WIN XP
using
the
CD Installation disc. Now my computer will not Boot up in Win XP. It gets
to
the Windows Home page and reboots. It will not enter Safemode either. The
disc checks out ok and the same problem appears in another computer using
the
same disc, and in the other computer you can see all files except where
the
security was at the Administrator level.
Win XP says there isn't a problem with the disc so please can somebody
tell
me why it will not boot up correctly? I have made a chkdsk c: /R it
repaired
some errors but keeps rebooting. Can I turn off Auto Reboot outside of
windows?



  #3  
Old June 9th 07, 05:52 PM posted to microsoft.public.windowsxp.help_and_support
Bernie
external usenet poster
 
Posts: 35
Default Boot Problem

Maybe it isn't dead yet as I can see it fully on another computer. Maybe I
will rebuild the computer with a new drive then use this a slave and try to
get the files off that I want.
I had SP2 loaded should I repair using SP2?

"Mark L. Ferguson" wrote:

If it will not enter safe mode, it is not repaired. Did you run a Repair
after the successful chkdsk? If so, you probably have a damaged hard drive.

--
Mark L. Ferguson
..
"Bernie" wrote in message
news
Hi I had a problem with the OS and repaired succesfully(?) with WIN XP
using
the
CD Installation disc. Now my computer will not Boot up in Win XP. It gets
to
the Windows Home page and reboots. It will not enter Safemode either. The
disc checks out ok and the same problem appears in another computer using
the
same disc, and in the other computer you can see all files except where
the
security was at the Administrator level.
Win XP says there isn't a problem with the disc so please can somebody
tell
me why it will not boot up correctly? I have made a chkdsk c: /R it
repaired
some errors but keeps rebooting. Can I turn off Auto Reboot outside of
windows?




  #4  
Old June 9th 07, 06:22 PM posted to microsoft.public.windowsxp.help_and_support
Mark L. Ferguson
external usenet poster
 
Posts: 4,253
Default Boot Problem

If your system was original with no SP2, take it out with add/remove, run the
repair, and reinstall sp2.
--
Was this post helpful to you? Then click the "Yes" button, below.
Voting helps others who use the web interface.
Mark L. Ferguson



"Bernie" wrote:

Maybe it isn't dead yet as I can see it fully on another computer. Maybe I
will rebuild the computer with a new drive then use this a slave and try to
get the files off that I want.
I had SP2 loaded should I repair using SP2?

"Mark L. Ferguson" wrote:

If it will not enter safe mode, it is not repaired. Did you run a Repair
after the successful chkdsk? If so, you probably have a damaged hard drive.

--
Mark L. Ferguson
..
"Bernie" wrote in message
news
Hi I had a problem with the OS and repaired succesfully(?) with WIN XP
using
the
CD Installation disc. Now my computer will not Boot up in Win XP. It gets
to
the Windows Home page and reboots. It will not enter Safemode either. The
disc checks out ok and the same problem appears in another computer using
the
same disc, and in the other computer you can see all files except where
the
security was at the Administrator level.
Win XP says there isn't a problem with the disc so please can somebody
tell
me why it will not boot up correctly? I have made a chkdsk c: /R it
repaired
some errors but keeps rebooting. Can I turn off Auto Reboot outside of
windows?




  #5  
Old June 9th 07, 09:46 PM posted to microsoft.public.windowsxp.help_and_support
Anna
external usenet poster
 
Posts: 2,039
Default Boot Problem


"Bernie" wrote in message
news Hi I had a problem with the OS and repaired succesfully(?) with WIN
XP
using
the
CD Installation disc. Now my computer will not Boot up in Win XP. It
gets
to
the Windows Home page and reboots. It will not enter Safemode either.
The
disc checks out ok and the same problem appears in another computer
using
the
same disc, and in the other computer you can see all files except
where
the
security was at the Administrator level.
Win XP says there isn't a problem with the disc so please can
somebody
tell
me why it will not boot up correctly? I have made a chkdsk c: /R it
repaired
some errors but keeps rebooting. Can I turn off Auto Reboot outside
of
windows?



"Mark L. Ferguson" wrote:
If it will not enter safe mode, it is not repaired. Did you run a
Repair
after the successful chkdsk? If so, you probably have a damaged hard
drive.

--
Mark L. Ferguson



"Bernie" wrote:
Maybe it isn't dead yet as I can see it fully on another computer. Maybe
I
will rebuild the computer with a new drive then use this a slave and try
to
get the files off that I want.
I had SP2 loaded should I repair using SP2?



"Mark L. Ferguson" wrote in
message ...
If your system was original with no SP2, take it out with add/remove, run
the
repair, and reinstall sp2.
--
Was this post helpful to you? Then click the "Yes" button, below.
Voting helps others who use the web interface.
Mark L. Ferguson



Bernie:
Do the following in the order given...

1. Reconnect that problem HDD as a secondary HDD in another machine and copy
off whatever files are important to you. On the other hand, if you already
have a current backup of the drive, that's fine.

2. Download the HDD diagnostic utility from the web site of the
manufacturer of your HDD and check it out. It's possible you may be dealing
with a defective disk so it's something you should know about,
notwithstanding that you're able to access its data.

3. Run a Repair install and hope for the best. You'll use your XP
installation CD with SP2 to do so. I don't quite understand Mark's last
comment about "tak(ing) it out with add/remove, run the repair, and
reinstall sp2". Since you apparently have an XP installation CD with SP2,
that's all that's necessary to run the Repair. I assume you know how to do
this. If not, there are a number of websites that contain step-by-step
instructions for undertaking a Repair install. If you do a Google search on
"XP repair install", you'll be pointed to many of these sites. Here are a
few...
http://www.michaelstevenstech.com/XP...install.htm#RI
http://www.webtree.ca/windowsxp/repair_xp.htm
http://www.geekstogo.com/forum/index.php?showtopic=138

Assuming the Repair install is successful, you should use your A-V program
to immediately check out your PC for any virus infestation. Also, you will
need to download/install *all* the MS critical updates since SP2. (Again,
I'm assuming that you'll be undertaking the Repair install with a XP CD that
contains SP2).
Anna


  #6  
Old June 11th 07, 05:04 PM posted to microsoft.public.windowsxp.help_and_support
thecreator
external usenet poster
 
Posts: 727
Default Boot Problem

Hi Bernie,

Do you have more than one partition on your current Hard Drive? If you
do, you could use Acronis True Image 10 Home Retail CD and back up your data
files onto the other partition, then you can reformat and reinstall Windows
XP.

Once you get the operating system back in working order, created a full
partition image, so you don't need to reinstall Windows XP again, just
restore the Drive Image. Make any sense?


--
thecreator

"Bernie" wrote in message
...
Maybe it isn't dead yet as I can see it fully on another computer. Maybe
I
will rebuild the computer with a new drive then use this a slave and try
to
get the files off that I want.
I had SP2 loaded should I repair using SP2?

"Mark L. Ferguson" wrote:

If it will not enter safe mode, it is not repaired. Did you run a Repair
after the successful chkdsk? If so, you probably have a damaged hard
drive.

--
Mark L. Ferguson
..
"Bernie" wrote in message
news
Hi I had a problem with the OS and repaired succesfully(?) with WIN XP
using
the
CD Installation disc. Now my computer will not Boot up in Win XP. It
gets
to
the Windows Home page and reboots. It will not enter Safemode either.
The
disc checks out ok and the same problem appears in another computer
using
the
same disc, and in the other computer you can see all files except where
the
security was at the Administrator level.
Win XP says there isn't a problem with the disc so please can somebody
tell
me why it will not boot up correctly? I have made a chkdsk c: /R it
repaired
some errors but keeps rebooting. Can I turn off Auto Reboot outside of
windows?






  #7  
Old June 12th 07, 11:58 AM posted to microsoft.public.windowsxp.help_and_support
Bernie
external usenet poster
 
Posts: 35
Default Boot Problem

I will not buy this sw but I have the maxtor disc sw to create a partition so
its an option, but I cannot get my user account open to copy the files. I was
the administrator but when I put the disc in another machine I cannot see the
files. How can I overcome this?

"thecreator" wrote:

Hi Bernie,

Do you have more than one partition on your current Hard Drive? If you
do, you could use Acronis True Image 10 Home Retail CD and back up your data
files onto the other partition, then you can reformat and reinstall Windows
XP.

Once you get the operating system back in working order, created a full
partition image, so you don't need to reinstall Windows XP again, just
restore the Drive Image. Make any sense?


--
thecreator

"Bernie" wrote in message
...
Maybe it isn't dead yet as I can see it fully on another computer. Maybe
I
will rebuild the computer with a new drive then use this a slave and try
to
get the files off that I want.
I had SP2 loaded should I repair using SP2?

"Mark L. Ferguson" wrote:

If it will not enter safe mode, it is not repaired. Did you run a Repair
after the successful chkdsk? If so, you probably have a damaged hard
drive.

--
Mark L. Ferguson
..
"Bernie" wrote in message
news Hi I had a problem with the OS and repaired succesfully(?) with WIN XP
using
the
CD Installation disc. Now my computer will not Boot up in Win XP. It
gets
to
the Windows Home page and reboots. It will not enter Safemode either.
The
disc checks out ok and the same problem appears in another computer
using
the
same disc, and in the other computer you can see all files except where
the
security was at the Administrator level.
Win XP says there isn't a problem with the disc so please can somebody
tell
me why it will not boot up correctly? I have made a chkdsk c: /R it
repaired
some errors but keeps rebooting. Can I turn off Auto Reboot outside of
windows?






  #8  
Old June 12th 07, 12:00 PM posted to microsoft.public.windowsxp.help_and_support
Bernie
external usenet poster
 
Posts: 35
Default Boot Problem

Most of this I have already tried the problem is I cannot get my user account
open to copy the files. I was the administrator but when I put the disc in
another machine I cannot see the files. How can I overcome this?

"Anna" wrote:


"Bernie" wrote in message
news Hi I had a problem with the OS and repaired succesfully(?) with WIN
XP
using
the
CD Installation disc. Now my computer will not Boot up in Win XP. It
gets
to
the Windows Home page and reboots. It will not enter Safemode either.
The
disc checks out ok and the same problem appears in another computer
using
the
same disc, and in the other computer you can see all files except
where
the
security was at the Administrator level.
Win XP says there isn't a problem with the disc so please can
somebody
tell
me why it will not boot up correctly? I have made a chkdsk c: /R it
repaired
some errors but keeps rebooting. Can I turn off Auto Reboot outside
of
windows?



"Mark L. Ferguson" wrote:
If it will not enter safe mode, it is not repaired. Did you run a
Repair
after the successful chkdsk? If so, you probably have a damaged hard
drive.

--
Mark L. Ferguson



"Bernie" wrote:
Maybe it isn't dead yet as I can see it fully on another computer. Maybe
I
will rebuild the computer with a new drive then use this a slave and try
to
get the files off that I want.
I had SP2 loaded should I repair using SP2?



"Mark L. Ferguson" wrote in
message ...
If your system was original with no SP2, take it out with add/remove, run
the
repair, and reinstall sp2.
--
Was this post helpful to you? Then click the "Yes" button, below.
Voting helps others who use the web interface.
Mark L. Ferguson



Bernie:
Do the following in the order given...

1. Reconnect that problem HDD as a secondary HDD in another machine and copy
off whatever files are important to you. On the other hand, if you already
have a current backup of the drive, that's fine.

2. Download the HDD diagnostic utility from the web site of the
manufacturer of your HDD and check it out. It's possible you may be dealing
with a defective disk so it's something you should know about,
notwithstanding that you're able to access its data.

3. Run a Repair install and hope for the best. You'll use your XP
installation CD with SP2 to do so. I don't quite understand Mark's last
comment about "tak(ing) it out with add/remove, run the repair, and
reinstall sp2". Since you apparently have an XP installation CD with SP2,
that's all that's necessary to run the Repair. I assume you know how to do
this. If not, there are a number of websites that contain step-by-step
instructions for undertaking a Repair install. If you do a Google search on
"XP repair install", you'll be pointed to many of these sites. Here are a
few...
http://www.michaelstevenstech.com/XP...install.htm#RI
http://www.webtree.ca/windowsxp/repair_xp.htm
http://www.geekstogo.com/forum/index.php?showtopic=138

Assuming the Repair install is successful, you should use your A-V program
to immediately check out your PC for any virus infestation. Also, you will
need to download/install *all* the MS critical updates since SP2. (Again,
I'm assuming that you'll be undertaking the Repair install with a XP CD that
contains SP2).
Anna



  #9  
Old June 12th 07, 12:13 PM posted to microsoft.public.windowsxp.help_and_support
Ricky
external usenet poster
 
Posts: 385
Default Boot Problem

If you put your disk in another machine you'll need to take ownership of
the files to see them. Have a look here..
How to take ownership of a file or folder in Windows XP
http://support.microsoft.com/default...&Product=winxp
In XP Home you have to boot in safe mode to see the security tab. In XP
Pro you have to disable simple file sharing.

"Bernie" wrote in message
...
I will not buy this sw but I have the maxtor disc sw to create a
partition so
its an option, but I cannot get my user account open to copy the
files. I was
the administrator but when I put the disc in another machine I cannot
see the
files. How can I overcome this?

"thecreator" wrote:

Hi Bernie,

Do you have more than one partition on your current Hard Drive?
If you
do, you could use Acronis True Image 10 Home Retail CD and back up
your data
files onto the other partition, then you can reformat and reinstall
Windows
XP.

Once you get the operating system back in working order, created
a full
partition image, so you don't need to reinstall Windows XP again,
just
restore the Drive Image. Make any sense?


--
thecreator

"Bernie" wrote in message
...
Maybe it isn't dead yet as I can see it fully on another computer.
Maybe
I
will rebuild the computer with a new drive then use this a slave
and try
to
get the files off that I want.
I had SP2 loaded should I repair using SP2?

"Mark L. Ferguson" wrote:

If it will not enter safe mode, it is not repaired. Did you run a
Repair
after the successful chkdsk? If so, you probably have a damaged
hard
drive.

--
Mark L. Ferguson
..
"Bernie" wrote in message
news Hi I had a problem with the OS and repaired succesfully(?) with
WIN XP
using
the
CD Installation disc. Now my computer will not Boot up in Win
XP. It
gets
to
the Windows Home page and reboots. It will not enter Safemode
either.
The
disc checks out ok and the same problem appears in another
computer
using
the
same disc, and in the other computer you can see all files
except where
the
security was at the Administrator level.
Win XP says there isn't a problem with the disc so please can
somebody
tell
me why it will not boot up correctly? I have made a chkdsk c: /R
it
repaired
some errors but keeps rebooting. Can I turn off Auto Reboot
outside of
windows?








  #10  
Old June 12th 07, 05:15 PM posted to microsoft.public.windowsxp.help_and_support
thecreator
external usenet poster
 
Posts: 727
Default Boot Problem

Hi Bernie,

You can't from another computer. That's why I recommended Acronis True
Image 10 Home software. The question arises, if the Maxtor Disc Software can
create another partition from the free space left, without destroying the
existing data on the Hard Drive.

Acronis True Image 10 Home from newegg.com and also its Disk Director
Suite 10.0-Retail

http://www.newegg.com/Product/Produc...82E16832200003

http://www.newegg.com/Product/Produc...82E16832200002

The first time you use the software, you need to use it from the CD
itself. You can't install the software onto the computer you are having
problems with. The CDs are bootable and you can run them on the computer you
are having problems with. Make sure the CD is the device that is first in
the Boot order.

When you boot from the CD, the security of Windows XP, does not come
into play.

You may need to buy also, another Hard Drive, if your current Hard Drive
is going bad. Before it goes bad, use Acronis Disk Director to copy the
partition to the other Hard Drive. Do not move it, in case something goes
wrong. COPY.


--
thecreator





"Bernie" wrote in message
...
I will not buy this sw but I have the maxtor disc sw to create a partition
so
its an option, but I cannot get my user account open to copy the files. I
was
the administrator but when I put the disc in another machine I cannot see
the
files. How can I overcome this?

"thecreator" wrote:

Hi Bernie,

Do you have more than one partition on your current Hard Drive? If
you
do, you could use Acronis True Image 10 Home Retail CD and back up your
data
files onto the other partition, then you can reformat and reinstall
Windows
XP.

Once you get the operating system back in working order, created a
full
partition image, so you don't need to reinstall Windows XP again, just
restore the Drive Image. Make any sense?


--
thecreator

"Bernie" wrote in message
...
Maybe it isn't dead yet as I can see it fully on another computer.
Maybe
I
will rebuild the computer with a new drive then use this a slave and
try
to
get the files off that I want.
I had SP2 loaded should I repair using SP2?

"Mark L. Ferguson" wrote:

If it will not enter safe mode, it is not repaired. Did you run a
Repair
after the successful chkdsk? If so, you probably have a damaged hard
drive.

--
Mark L. Ferguson
..
"Bernie" wrote in message
news Hi I had a problem with the OS and repaired succesfully(?) with WIN
XP
using
the
CD Installation disc. Now my computer will not Boot up in Win XP. It
gets
to
the Windows Home page and reboots. It will not enter Safemode
either.
The
disc checks out ok and the same problem appears in another computer
using
the
same disc, and in the other computer you can see all files except
where
the
security was at the Administrator level.
Win XP says there isn't a problem with the disc so please can
somebody
tell
me why it will not boot up correctly? I have made a chkdsk c: /R it
repaired
some errors but keeps rebooting. Can I turn off Auto Reboot outside
of
windows?








  #11  
Old June 13th 07, 12:45 PM posted to microsoft.public.windowsxp.help_and_support
Bernie
external usenet poster
 
Posts: 35
Default Boot Problem

Free evalutation of "Acronis True Image 10 Home " is available for a 15 day
trial??
OK.
I load my disc into another machine?
I download the s/w onto a CD?
I boot with this CD then transfer the files to the other disc?
I don't care about the disc being defunk but there was no sign that this was
going to happen AND the disc checks out ok so all I want is the files. Then
I'll reformat and see if its the disc or buy another drive, probably the
latter.
Should the trial version work to do what I want? I did try taking ownership
last week but had problems as I guess the disc was a slave and not master.
Being cool about this but I really MUST backup the files that I want to keep
just never do and so sign of the death clicking from the drive either!!

"thecreator" wrote:

Hi Bernie,

You can't from another computer. That's why I recommended Acronis True
Image 10 Home software. The question arises, if the Maxtor Disc Software can
create another partition from the free space left, without destroying the
existing data on the Hard Drive.

Acronis True Image 10 Home from newegg.com and also its Disk Director
Suite 10.0-Retail

http://www.newegg.com/Product/Produc...82E16832200003

http://www.newegg.com/Product/Produc...82E16832200002

The first time you use the software, you need to use it from the CD
itself. You can't install the software onto the computer you are having
problems with. The CDs are bootable and you can run them on the computer you
are having problems with. Make sure the CD is the device that is first in
the Boot order.

When you boot from the CD, the security of Windows XP, does not come
into play.

You may need to buy also, another Hard Drive, if your current Hard Drive
is going bad. Before it goes bad, use Acronis Disk Director to copy the
partition to the other Hard Drive. Do not move it, in case something goes
wrong. COPY.


--
thecreator





"Bernie" wrote in message
...
I will not buy this sw but I have the maxtor disc sw to create a partition
so
its an option, but I cannot get my user account open to copy the files. I
was
the administrator but when I put the disc in another machine I cannot see
the
files. How can I overcome this?

"thecreator" wrote:

Hi Bernie,

Do you have more than one partition on your current Hard Drive? If
you
do, you could use Acronis True Image 10 Home Retail CD and back up your
data
files onto the other partition, then you can reformat and reinstall
Windows
XP.

Once you get the operating system back in working order, created a
full
partition image, so you don't need to reinstall Windows XP again, just
restore the Drive Image. Make any sense?


--
thecreator

"Bernie" wrote in message
...
Maybe it isn't dead yet as I can see it fully on another computer.
Maybe
I
will rebuild the computer with a new drive then use this a slave and
try
to
get the files off that I want.
I had SP2 loaded should I repair using SP2?

"Mark L. Ferguson" wrote:

If it will not enter safe mode, it is not repaired. Did you run a
Repair
after the successful chkdsk? If so, you probably have a damaged hard
drive.

--
Mark L. Ferguson
..
"Bernie" wrote in message
news Hi I had a problem with the OS and repaired succesfully(?) with WIN
XP
using
the
CD Installation disc. Now my computer will not Boot up in Win XP. It
gets
to
the Windows Home page and reboots. It will not enter Safemode
either.
The
disc checks out ok and the same problem appears in another computer
using
the
same disc, and in the other computer you can see all files except
where
the
security was at the Administrator level.
Win XP says there isn't a problem with the disc so please can
somebody
tell
me why it will not boot up correctly? I have made a chkdsk c: /R it
repaired
some errors but keeps rebooting. Can I turn off Auto Reboot outside
of
windows?









  #12  
Old June 13th 07, 12:49 PM posted to microsoft.public.windowsxp.help_and_support
Bernie
external usenet poster
 
Posts: 35
Default Boot Problem

Sorry just found the english version ..
http://www.acronis.com/homecomputing...oad/trueimage/
Again if this is the full version should it be enough to open the locked
files? And then what do I do? Please/Thankyou
"thecreator" wrote:

Hi Bernie,

You can't from another computer. That's why I recommended Acronis True
Image 10 Home software. The question arises, if the Maxtor Disc Software can
create another partition from the free space left, without destroying the
existing data on the Hard Drive.

Acronis True Image 10 Home from newegg.com and also its Disk Director
Suite 10.0-Retail

http://www.newegg.com/Product/Produc...82E16832200003

http://www.newegg.com/Product/Produc...82E16832200002

The first time you use the software, you need to use it from the CD
itself. You can't install the software onto the computer you are having
problems with. The CDs are bootable and you can run them on the computer you
are having problems with. Make sure the CD is the device that is first in
the Boot order.

When you boot from the CD, the security of Windows XP, does not come
into play.

You may need to buy also, another Hard Drive, if your current Hard Drive
is going bad. Before it goes bad, use Acronis Disk Director to copy the
partition to the other Hard Drive. Do not move it, in case something goes
wrong. COPY.


--
thecreator





"Bernie" wrote in message
...
I will not buy this sw but I have the maxtor disc sw to create a partition
so
its an option, but I cannot get my user account open to copy the files. I
was
the administrator but when I put the disc in another machine I cannot see
the
files. How can I overcome this?

"thecreator" wrote:

Hi Bernie,

Do you have more than one partition on your current Hard Drive? If
you
do, you could use Acronis True Image 10 Home Retail CD and back up your
data
files onto the other partition, then you can reformat and reinstall
Windows
XP.

Once you get the operating system back in working order, created a
full
partition image, so you don't need to reinstall Windows XP again, just
restore the Drive Image. Make any sense?


--
thecreator

"Bernie" wrote in message
...
Maybe it isn't dead yet as I can see it fully on another computer.
Maybe
I
will rebuild the computer with a new drive then use this a slave and
try
to
get the files off that I want.
I had SP2 loaded should I repair using SP2?

"Mark L. Ferguson" wrote:

If it will not enter safe mode, it is not repaired. Did you run a
Repair
after the successful chkdsk? If so, you probably have a damaged hard
drive.

--
Mark L. Ferguson
..
"Bernie" wrote in message
news Hi I had a problem with the OS and repaired succesfully(?) with WIN
XP
using
the
CD Installation disc. Now my computer will not Boot up in Win XP. It
gets
to
the Windows Home page and reboots. It will not enter Safemode
either.
The
disc checks out ok and the same problem appears in another computer
using
the
same disc, and in the other computer you can see all files except
where
the
security was at the Administrator level.
Win XP says there isn't a problem with the disc so please can
somebody
tell
me why it will not boot up correctly? I have made a chkdsk c: /R it
repaired
some errors but keeps rebooting. Can I turn off Auto Reboot outside
of
windows?









 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off






All times are GMT +1. The time now is 10:54 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 PCbanter.
The comments are property of their posters.