If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Clips splitting incorrectly
my problem is that often (alot) a clip will retain one
frame from the clip previous to it. if the clips are in succesion, this is not a problem, but if i want to move the clips to a different location, when the clip plays in the movie, it shows one frame of the clip previously. what i have to do is trim the clip while in the timeline. this is happening more since upgrading to the final version of moviemaker 2 from beta. also is hanging more and will cause a restart. any ideas? |
Ads |
#2
|
|||
|
|||
Clips splitting incorrectly
Travis,
On the clip splitting, try being just a tad on the other side of the cut point before doing the slip. When you are on one side of the exact point you get what you are seeing, but when on the other side, it'll be clean. I forget which side is which, but it's easy to do some and check it. On your hanging issue, have you gone through checking your hardware acceleration and looked for clashing codecs? http://pws.chartermi.net/~papajohn/MM2.html PapaJohn "Travis" wrote in message ... my problem is that often (alot) a clip will retain one frame from the clip previous to it. if the clips are in succesion, this is not a problem, but if i want to move the clips to a different location, when the clip plays in the movie, it shows one frame of the clip previously. what i have to do is trim the clip while in the timeline. this is happening more since upgrading to the final version of moviemaker 2 from beta. also is hanging more and will cause a restart. any ideas? |
#3
|
|||
|
|||
Clips splitting incorrectly
i guess i'm not following you completly. the clips are
the ones that are automatically split on capture from my dv camera using windows movie maker. i want to be able to just pull the clips down without having to cut the first frame off every time. -----Original Message----- Travis, On the clip splitting, try being just a tad on the other side of the cut point before doing the slip. When you are on one side of the exact point you get what you are seeing, but when on the other side, it'll be clean. I forget which side is which, but it's easy to do some and check it. On your hanging issue, have you gone through checking your hardware acceleration and looked for clashing codecs? http://pws.chartermi.net/~papajohn/MM2.html PapaJohn "Travis" wrote in message ... my problem is that often (alot) a clip will retain one frame from the clip previous to it. if the clips are in succesion, this is not a problem, but if i want to move the clips to a different location, when the clip plays in the movie, it shows one frame of the clip previously. what i have to do is trim the clip while in the timeline. this is happening more since upgrading to the final version of moviemaker 2 from beta. also is hanging more and will cause a restart. any ideas? . |
#4
|
|||
|
|||
Clips splitting incorrectly
Travis,
I guess I was thinking that you were manually cutting the clips. Is it from a digital camcorder where Movie Maker uses timecode, or from an analog source that it is doing scene detection on? PapaJohn "Travis" wrote in message ... i guess i'm not following you completly. the clips are the ones that are automatically split on capture from my dv camera using windows movie maker. i want to be able to just pull the clips down without having to cut the first frame off every time. -----Original Message----- Travis, On the clip splitting, try being just a tad on the other side of the cut point before doing the slip. When you are on one side of the exact point you get what you are seeing, but when on the other side, it'll be clean. I forget which side is which, but it's easy to do some and check it. On your hanging issue, have you gone through checking your hardware acceleration and looked for clashing codecs? http://pws.chartermi.net/~papajohn/MM2.html PapaJohn "Travis" wrote in message ... my problem is that often (alot) a clip will retain one frame from the clip previous to it. if the clips are in succesion, this is not a problem, but if i want to move the clips to a different location, when the clip plays in the movie, it shows one frame of the clip previously. what i have to do is trim the clip while in the timeline. this is happening more since upgrading to the final version of moviemaker 2 from beta. also is hanging more and will cause a restart. any ideas? . |
Thread Tools | |
Display Modes | |
|
|