If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
setting up fax
Hello.
When setting up Windows Fax the instructions say to click on the add/remove components button and select 'fax services'. However, when I go to add/remove components, 'fax services' along with other components are already checked. Does this mean I should uncheck 'fax services' and then select next? I don't want to inadvertently delete something. |
Ads |
#2
|
|||
|
|||
setting up fax
GetGreen wrote:
Hello. When setting up Windows Fax the instructions say to click on the add/remove components button and select 'fax services'. However, when I go to add/remove components, 'fax services' along with other components are already checked. Does this mean I should uncheck 'fax services' and then select next? I don't want to inadvertently delete something. From your description, it seems that Fax Services has already been installed. What makes you think it hasn't? When you click Start All Programs Accessories Communications is there an entry for "Fax" in the next menu? Copy the following line and paste into the Start Run box. %SystemRoot%\System32\FxsClnt.exe /new What happens? -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html |
#3
|
|||
|
|||
setting up fax
GetGreen wrote:
Hello. When setting up Windows Fax the instructions say to click on the add/remove components button and select 'fax services'. However, when I go to add/remove components, 'fax services' along with other components are already checked. Does this mean I should uncheck 'fax services' and then select next? I don't want to inadvertently delete something. From your description, it seems that Fax Services has already been installed. What makes you think it hasn't? When you click Start All Programs Accessories Communications is there an entry for "Fax" in the next menu? Copy the following line and paste into the Start Run box. %SystemRoot%\System32\FxsClnt.exe /new What happens? -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html |
#4
|
|||
|
|||
setting up fax
Thank you.
Yes, there is an entry for fax; and when I copy and paste the line into the run menu, the fax console comes up. So does this mean I am setup to fax? Thanks again. Michelle "Lem" wrote: GetGreen wrote: Hello. When setting up Windows Fax the instructions say to click on the add/remove components button and select 'fax services'. However, when I go to add/remove components, 'fax services' along with other components are already checked. Does this mean I should uncheck 'fax services' and then select next? I don't want to inadvertently delete something. From your description, it seems that Fax Services has already been installed. What makes you think it hasn't? When you click Start All Programs Accessories Communications is there an entry for "Fax" in the next menu? Copy the following line and paste into the Start Run box. %SystemRoot%\System32\FxsClnt.exe /new What happens? -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html . |
#5
|
|||
|
|||
setting up fax
Thank you. Yes, there is an entry for fax; and when I copy and paste the line into the run menu, the fax console comes up. So does this mean I am setup to fax? Thanks again. Michelle "Lem" wrote: GetGreen wrote: Hello. When setting up Windows Fax the instructions say to click on the add/remove components button and select 'fax services'. However, when I go to add/remove components, 'fax services' along with other components are already checked. Does this mean I should uncheck 'fax services' and then select next? I don't want to inadvertently delete something. From your description, it seems that Fax Services has already been installed. What makes you think it hasn't? When you click Start All Programs Accessories Communications is there an entry for "Fax" in the next menu? Copy the following line and paste into the Start Run box. %SystemRoot%\System32\FxsClnt.exe /new What happens? -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html . |
#6
|
|||
|
|||
setting up fax
GetGreen wrote:
Thank you. Yes, there is an entry for fax; and when I copy and paste the line into the run menu, the fax console comes up. So does this mean I am setup to fax? Thanks again. Michelle "Lem" wrote: GetGreen wrote: Hello. When setting up Windows Fax the instructions say to click on the add/remove components button and select 'fax services'. However, when I go to add/remove components, 'fax services' along with other components are already checked. Does this mean I should uncheck 'fax services' and then select next? I don't want to inadvertently delete something. From your description, it seems that Fax Services has already been installed. What makes you think it hasn't? When you click Start All Programs Accessories Communications is there an entry for "Fax" in the next menu? Copy the following line and paste into the Start Run box. %SystemRoot%\System32\FxsClnt.exe /new What happens? -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html . Yes (almost; see below to configure fax) ... but remember, you need to connect your fax modem to an analog phone line (regular, old-fashioned phone line). If you have DSL service, you can share the line with phone/fax and DSL by using appropriate filters. If you have cable internet service, you need to use a "real" phone line for the fax, not the cable connection. See this article and follow directions to configure the fax: http://support.microsoft.com/kb/306550 One of the screens in the Fax Configuration Wizard allows you to specify if the fax modem will automatically answer (after N rings) or if you must manually answer. Keep in mind that Windows XP Fax Services *cannot* distinguish between incoming fax calls and incoming voice calls. Thus, if you connect the fax modem to a phone line that is shared with your regular telephone, you may want to set the fax to manual receive to prevent Fax Services from answering all of your incoming calls. "TSID" is the telephone number of the line to which you connect the fax modem. -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html |
#7
|
|||
|
|||
setting up fax
GetGreen wrote:
Thank you. Yes, there is an entry for fax; and when I copy and paste the line into the run menu, the fax console comes up. So does this mean I am setup to fax? Thanks again. Michelle "Lem" wrote: GetGreen wrote: Hello. When setting up Windows Fax the instructions say to click on the add/remove components button and select 'fax services'. However, when I go to add/remove components, 'fax services' along with other components are already checked. Does this mean I should uncheck 'fax services' and then select next? I don't want to inadvertently delete something. From your description, it seems that Fax Services has already been installed. What makes you think it hasn't? When you click Start All Programs Accessories Communications is there an entry for "Fax" in the next menu? Copy the following line and paste into the Start Run box. %SystemRoot%\System32\FxsClnt.exe /new What happens? -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html . Yes (almost; see below to configure fax) ... but remember, you need to connect your fax modem to an analog phone line (regular, old-fashioned phone line). If you have DSL service, you can share the line with phone/fax and DSL by using appropriate filters. If you have cable internet service, you need to use a "real" phone line for the fax, not the cable connection. See this article and follow directions to configure the fax: http://support.microsoft.com/kb/306550 One of the screens in the Fax Configuration Wizard allows you to specify if the fax modem will automatically answer (after N rings) or if you must manually answer. Keep in mind that Windows XP Fax Services *cannot* distinguish between incoming fax calls and incoming voice calls. Thus, if you connect the fax modem to a phone line that is shared with your regular telephone, you may want to set the fax to manual receive to prevent Fax Services from answering all of your incoming calls. "TSID" is the telephone number of the line to which you connect the fax modem. -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html |
#8
|
|||
|
|||
setting up fax
Thank you Lem for sharing the information and continued help.
I seem to be encountering a problem when I configure the fax console. A message comes up that says, "a connection to the fax swerver cannot be made". Any suggestions on how I should proceed from here? Again, your advice is much appreciated. Michelle "Lem" wrote: GetGreen wrote: Thank you. Yes, there is an entry for fax; and when I copy and paste the line into the run menu, the fax console comes up. So does this mean I am setup to fax? Thanks again. Michelle "Lem" wrote: GetGreen wrote: Hello. When setting up Windows Fax the instructions say to click on the add/remove components button and select 'fax services'. However, when I go to add/remove components, 'fax services' along with other components are already checked. Does this mean I should uncheck 'fax services' and then select next? I don't want to inadvertently delete something. From your description, it seems that Fax Services has already been installed. What makes you think it hasn't? When you click Start All Programs Accessories Communications is there an entry for "Fax" in the next menu? Copy the following line and paste into the Start Run box. %SystemRoot%\System32\FxsClnt.exe /new What happens? -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html . Yes (almost; see below to configure fax) ... but remember, you need to connect your fax modem to an analog phone line (regular, old-fashioned phone line). If you have DSL service, you can share the line with phone/fax and DSL by using appropriate filters. If you have cable internet service, you need to use a "real" phone line for the fax, not the cable connection. See this article and follow directions to configure the fax: http://support.microsoft.com/kb/306550 One of the screens in the Fax Configuration Wizard allows you to specify if the fax modem will automatically answer (after N rings) or if you must manually answer. Keep in mind that Windows XP Fax Services *cannot* distinguish between incoming fax calls and incoming voice calls. Thus, if you connect the fax modem to a phone line that is shared with your regular telephone, you may want to set the fax to manual receive to prevent Fax Services from answering all of your incoming calls. "TSID" is the telephone number of the line to which you connect the fax modem. -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html . |
#9
|
|||
|
|||
setting up fax
Thank you Lem for sharing the information and continued help.
I seem to be encountering a problem when I configure the fax console. A message comes up that says, "a connection to the fax swerver cannot be made". Any suggestions on how I should proceed from here? Again, your advice is much appreciated. Michelle "Lem" wrote: GetGreen wrote: Thank you. Yes, there is an entry for fax; and when I copy and paste the line into the run menu, the fax console comes up. So does this mean I am setup to fax? Thanks again. Michelle "Lem" wrote: GetGreen wrote: Hello. When setting up Windows Fax the instructions say to click on the add/remove components button and select 'fax services'. However, when I go to add/remove components, 'fax services' along with other components are already checked. Does this mean I should uncheck 'fax services' and then select next? I don't want to inadvertently delete something. From your description, it seems that Fax Services has already been installed. What makes you think it hasn't? When you click Start All Programs Accessories Communications is there an entry for "Fax" in the next menu? Copy the following line and paste into the Start Run box. %SystemRoot%\System32\FxsClnt.exe /new What happens? -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html . Yes (almost; see below to configure fax) ... but remember, you need to connect your fax modem to an analog phone line (regular, old-fashioned phone line). If you have DSL service, you can share the line with phone/fax and DSL by using appropriate filters. If you have cable internet service, you need to use a "real" phone line for the fax, not the cable connection. See this article and follow directions to configure the fax: http://support.microsoft.com/kb/306550 One of the screens in the Fax Configuration Wizard allows you to specify if the fax modem will automatically answer (after N rings) or if you must manually answer. Keep in mind that Windows XP Fax Services *cannot* distinguish between incoming fax calls and incoming voice calls. Thus, if you connect the fax modem to a phone line that is shared with your regular telephone, you may want to set the fax to manual receive to prevent Fax Services from answering all of your incoming calls. "TSID" is the telephone number of the line to which you connect the fax modem. -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html . |
#10
|
|||
|
|||
setting up fax
GetGreen wrote:
Thank you Lem for sharing the information and continued help. I seem to be encountering a problem when I configure the fax console. A message comes up that says, "a connection to the fax swerver cannot be made". Any suggestions on how I should proceed from here? Again, your advice is much appreciated. Michelle "Lem" wrote: GetGreen wrote: Thank you. Yes, there is an entry for fax; and when I copy and paste the line into the run menu, the fax console comes up. So does this mean I am setup to fax? Thanks again. Michelle "Lem" wrote: GetGreen wrote: Hello. When setting up Windows Fax the instructions say to click on the add/remove components button and select 'fax services'. However, when I go to add/remove components, 'fax services' along with other components are already checked. Does this mean I should uncheck 'fax services' and then select next? I don't want to inadvertently delete something. From your description, it seems that Fax Services has already been installed. What makes you think it hasn't? When you click Start All Programs Accessories Communications is there an entry for "Fax" in the next menu? Copy the following line and paste into the Start Run box. %SystemRoot%\System32\FxsClnt.exe /new What happens? -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html . Yes (almost; see below to configure fax) ... but remember, you need to connect your fax modem to an analog phone line (regular, old-fashioned phone line). If you have DSL service, you can share the line with phone/fax and DSL by using appropriate filters. If you have cable internet service, you need to use a "real" phone line for the fax, not the cable connection. See this article and follow directions to configure the fax: http://support.microsoft.com/kb/306550 One of the screens in the Fax Configuration Wizard allows you to specify if the fax modem will automatically answer (after N rings) or if you must manually answer. Keep in mind that Windows XP Fax Services *cannot* distinguish between incoming fax calls and incoming voice calls. Thus, if you connect the fax modem to a phone line that is shared with your regular telephone, you may want to set the fax to manual receive to prevent Fax Services from answering all of your incoming calls. "TSID" is the telephone number of the line to which you connect the fax modem. -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html . This issue sometimes comes up if an antivirus application interferes with the installation of Fax Services. However, because you started this thread with Fax Services apparently already installed, I assume that you are not aware of any error messages that might have appeared during the installation. You could try UNchecking the box for Fax Services in Add/Remove Windows components and clicking OK (which should uninstall it), then temporarily disabling your antivirus application, and then reinstalling Fax Services. You should also confirm that you actually do have a fax modem. Open Device Manager (right click "My Computer" Properties Hardware Device Manager) and expand the entry for "Modems" by clicking the +. If the modem description does not explicitly include the word "fax" or "faxmodem" try Googling for the manufacturer's web page. Even if you have a fax modem, Windows Fax Services may not work with it -- there used to be a "hardware compatibility list" (now replaced by the Windows Logo'd Products List). If your modem is listed, it's supposed to work; if your modem isn't listed, working is not guaranteed. There are, however, fax modems not on the list that do work. http://winqual.microsoft.com/HCL/Default.aspx?m=x To quote from MS-MVP Hal Hostetler, who is knowledgeable about Windows Fax: QUOTE It's likely you have security data base corruption as documented he http://support.microsoft.com/kb/884018/EN-US/ You cannot add a Windows component in Windows XP You can either: 1. Get the hotfix mentioned in the KB article and install it. Microsoft usually waives any charges for support calls to get supported hotfixes listed in Knowledge Base articles. 2. Try this procedure using the Esentutl.exe utility mentioned in the KB article to recover from security database corruption: http://h10025.www1.hp.com/ewfrf/wc/d...name=c00270202 HP and Compaq Notebook PCs: Unable to Install Windows XP Fax Software I can report that the Esentutl utility has corrected the problem in a number of cases, HOWEVER, note that Microsoft does NOT recommend that you use the utility and would prefer you try the hotfix. /QUOTE Or ... you can try posting a new thread in this newsgroup with the subject "a connection to the fax server cannot be made" and perhaps someone with more specific knowledge than me will respond. -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html |
#11
|
|||
|
|||
setting up fax
GetGreen wrote:
Thank you Lem for sharing the information and continued help. I seem to be encountering a problem when I configure the fax console. A message comes up that says, "a connection to the fax swerver cannot be made". Any suggestions on how I should proceed from here? Again, your advice is much appreciated. Michelle "Lem" wrote: GetGreen wrote: Thank you. Yes, there is an entry for fax; and when I copy and paste the line into the run menu, the fax console comes up. So does this mean I am setup to fax? Thanks again. Michelle "Lem" wrote: GetGreen wrote: Hello. When setting up Windows Fax the instructions say to click on the add/remove components button and select 'fax services'. However, when I go to add/remove components, 'fax services' along with other components are already checked. Does this mean I should uncheck 'fax services' and then select next? I don't want to inadvertently delete something. From your description, it seems that Fax Services has already been installed. What makes you think it hasn't? When you click Start All Programs Accessories Communications is there an entry for "Fax" in the next menu? Copy the following line and paste into the Start Run box. %SystemRoot%\System32\FxsClnt.exe /new What happens? -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html . Yes (almost; see below to configure fax) ... but remember, you need to connect your fax modem to an analog phone line (regular, old-fashioned phone line). If you have DSL service, you can share the line with phone/fax and DSL by using appropriate filters. If you have cable internet service, you need to use a "real" phone line for the fax, not the cable connection. See this article and follow directions to configure the fax: http://support.microsoft.com/kb/306550 One of the screens in the Fax Configuration Wizard allows you to specify if the fax modem will automatically answer (after N rings) or if you must manually answer. Keep in mind that Windows XP Fax Services *cannot* distinguish between incoming fax calls and incoming voice calls. Thus, if you connect the fax modem to a phone line that is shared with your regular telephone, you may want to set the fax to manual receive to prevent Fax Services from answering all of your incoming calls. "TSID" is the telephone number of the line to which you connect the fax modem. -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html . This issue sometimes comes up if an antivirus application interferes with the installation of Fax Services. However, because you started this thread with Fax Services apparently already installed, I assume that you are not aware of any error messages that might have appeared during the installation. You could try UNchecking the box for Fax Services in Add/Remove Windows components and clicking OK (which should uninstall it), then temporarily disabling your antivirus application, and then reinstalling Fax Services. You should also confirm that you actually do have a fax modem. Open Device Manager (right click "My Computer" Properties Hardware Device Manager) and expand the entry for "Modems" by clicking the +. If the modem description does not explicitly include the word "fax" or "faxmodem" try Googling for the manufacturer's web page. Even if you have a fax modem, Windows Fax Services may not work with it -- there used to be a "hardware compatibility list" (now replaced by the Windows Logo'd Products List). If your modem is listed, it's supposed to work; if your modem isn't listed, working is not guaranteed. There are, however, fax modems not on the list that do work. http://winqual.microsoft.com/HCL/Default.aspx?m=x To quote from MS-MVP Hal Hostetler, who is knowledgeable about Windows Fax: QUOTE It's likely you have security data base corruption as documented he http://support.microsoft.com/kb/884018/EN-US/ You cannot add a Windows component in Windows XP You can either: 1. Get the hotfix mentioned in the KB article and install it. Microsoft usually waives any charges for support calls to get supported hotfixes listed in Knowledge Base articles. 2. Try this procedure using the Esentutl.exe utility mentioned in the KB article to recover from security database corruption: http://h10025.www1.hp.com/ewfrf/wc/d...name=c00270202 HP and Compaq Notebook PCs: Unable to Install Windows XP Fax Software I can report that the Esentutl utility has corrected the problem in a number of cases, HOWEVER, note that Microsoft does NOT recommend that you use the utility and would prefer you try the hotfix. /QUOTE Or ... you can try posting a new thread in this newsgroup with the subject "a connection to the fax server cannot be made" and perhaps someone with more specific knowledge than me will respond. -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html |
#12
|
|||
|
|||
setting up fax
Thank you for your continued help Lem.
When I try to configure the fax console I am getting a message that says "A connection to the fax server cannot be made". Seems I am hung up at this point. Do you have any suggestions. Thank you again. Michelle "Lem" wrote: GetGreen wrote: Thank you. Yes, there is an entry for fax; and when I copy and paste the line into the run menu, the fax console comes up. So does this mean I am setup to fax? Thanks again. Michelle "Lem" wrote: GetGreen wrote: Hello. When setting up Windows Fax the instructions say to click on the add/remove components button and select 'fax services'. However, when I go to add/remove components, 'fax services' along with other components are already checked. Does this mean I should uncheck 'fax services' and then select next? I don't want to inadvertently delete something. From your description, it seems that Fax Services has already been installed. What makes you think it hasn't? When you click Start All Programs Accessories Communications is there an entry for "Fax" in the next menu? Copy the following line and paste into the Start Run box. %SystemRoot%\System32\FxsClnt.exe /new What happens? -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html . Yes (almost; see below to configure fax) ... but remember, you need to connect your fax modem to an analog phone line (regular, old-fashioned phone line). If you have DSL service, you can share the line with phone/fax and DSL by using appropriate filters. If you have cable internet service, you need to use a "real" phone line for the fax, not the cable connection. See this article and follow directions to configure the fax: http://support.microsoft.com/kb/306550 One of the screens in the Fax Configuration Wizard allows you to specify if the fax modem will automatically answer (after N rings) or if you must manually answer. Keep in mind that Windows XP Fax Services *cannot* distinguish between incoming fax calls and incoming voice calls. Thus, if you connect the fax modem to a phone line that is shared with your regular telephone, you may want to set the fax to manual receive to prevent Fax Services from answering all of your incoming calls. "TSID" is the telephone number of the line to which you connect the fax modem. -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html . |
#13
|
|||
|
|||
setting up fax
Thank you for your continued help Lem.
When I try to configure the fax console I am getting a message that says "A connection to the fax server cannot be made". Seems I am hung up at this point. Do you have any suggestions. Thank you again. Michelle "Lem" wrote: GetGreen wrote: Thank you. Yes, there is an entry for fax; and when I copy and paste the line into the run menu, the fax console comes up. So does this mean I am setup to fax? Thanks again. Michelle "Lem" wrote: GetGreen wrote: Hello. When setting up Windows Fax the instructions say to click on the add/remove components button and select 'fax services'. However, when I go to add/remove components, 'fax services' along with other components are already checked. Does this mean I should uncheck 'fax services' and then select next? I don't want to inadvertently delete something. From your description, it seems that Fax Services has already been installed. What makes you think it hasn't? When you click Start All Programs Accessories Communications is there an entry for "Fax" in the next menu? Copy the following line and paste into the Start Run box. %SystemRoot%\System32\FxsClnt.exe /new What happens? -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html . Yes (almost; see below to configure fax) ... but remember, you need to connect your fax modem to an analog phone line (regular, old-fashioned phone line). If you have DSL service, you can share the line with phone/fax and DSL by using appropriate filters. If you have cable internet service, you need to use a "real" phone line for the fax, not the cable connection. See this article and follow directions to configure the fax: http://support.microsoft.com/kb/306550 One of the screens in the Fax Configuration Wizard allows you to specify if the fax modem will automatically answer (after N rings) or if you must manually answer. Keep in mind that Windows XP Fax Services *cannot* distinguish between incoming fax calls and incoming voice calls. Thus, if you connect the fax modem to a phone line that is shared with your regular telephone, you may want to set the fax to manual receive to prevent Fax Services from answering all of your incoming calls. "TSID" is the telephone number of the line to which you connect the fax modem. -- Lem Apollo 11 - 40 years ago: http://www.nasa.gov/mission_pages/ap...0th/index.html . |
#14
|
|||
|
|||
setting up fax
Lem wrote:
snip Yes (almost; see below to configure fax) ... but remember, you need to connect your fax modem to an analog phone line (regular, old-fashioned phone line). If you have DSL service, you can share the line with phone/fax and DSL by using appropriate filters. If you have cable internet service, you need to use a "real" phone line for the fax, not the cable connection. snip The bit about not being able to fax with a cable connection isn't necessarily true; If the user has cable telephone service (in addition to Internet service) it will probably work. It does for me. It's my understanding that faxing won't work with some cable phone services, but it works with my Time Warner connection. |
#15
|
|||
|
|||
setting up fax
Lem wrote:
snip Yes (almost; see below to configure fax) ... but remember, you need to connect your fax modem to an analog phone line (regular, old-fashioned phone line). If you have DSL service, you can share the line with phone/fax and DSL by using appropriate filters. If you have cable internet service, you need to use a "real" phone line for the fax, not the cable connection. snip The bit about not being able to fax with a cable connection isn't necessarily true; If the user has cable telephone service (in addition to Internet service) it will probably work. It does for me. It's my understanding that faxing won't work with some cable phone services, but it works with my Time Warner connection. |
|
Thread Tools | |
Display Modes | |
|
|