If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Kernel stack inpage error:0x0000007A & kernel data inpage error:0x
Recently I have these 2 error messages every time after using my computer for
awhile. After the error message had shown, it will then shut down & reboot itself May I know what’s wrong with my computer & how do I solve this problem ? Can someone please advise. I need to resolve these quickly. Please response Error Message from computer : “A problem has been detected and Windows has been shut down to prevent damage to your computer” Kernel stack inpage error If this is the first time you have seen this stop error screen, restart your computer. If this screen appear again, follow these steps : Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows update you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing If you need to use safe mode to remove or disable components, restart computer, press F8 to select Advanced startup options & select safe mode Technical information : Stop : 0X0000007A (0xc000000E,0xc000000E,0x00000….0x0B862000) Begin dump of physical memory “ orError Message from computer : “A problem has been detected and Windows has been shut down to prevent damage to your computer” Kernel data inpage error If this is the first time you have seen this stop error screen, restart your computer. If this screen appear again, follow these steps : Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows update you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing If you need to use safe mode to remove or disable components, restart computer, press F8 to select Advanced startup options & select safe mode Technical information : Stop : 0X0000007A Atapi.sp – Address F834B50C base at F833E000,datatamp 4802539d Begin dump of physical memory “ |
Ads |
#2
|
|||
|
|||
Kernel stack inpage error:0x0000007A & kernel data inpage error:0x
See the following
http://msdn.microsoft.com/en-gb/library/ms793989.aspx -- Peter Please Reply to Newsgroup for the benefit of others Requests for assistance by email can not and will not be acknowledged. "123noanser" wrote in message ... Recently I have these 2 error messages every time after using my computer for awhile. After the error message had shown, it will then shut down & reboot itself May I know what’s wrong with my computer & how do I solve this problem ? Can someone please advise. I need to resolve these quickly. Please response Error Message from computer : “A problem has been detected and Windows has been shut down to prevent damage to your computer” Kernel stack inpage error If this is the first time you have seen this stop error screen, restart your computer. If this screen appear again, follow these steps : Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows update you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing If you need to use safe mode to remove or disable components, restart computer, press F8 to select Advanced startup options & select safe mode Technical information : Stop : 0X0000007A (0xc000000E,0xc000000E,0x00000….0x0B862000) Begin dump of physical memory “ orError Message from computer : “A problem has been detected and Windows has been shut down to prevent damage to your computer” Kernel data inpage error If this is the first time you have seen this stop error screen, restart your computer. If this screen appear again, follow these steps : Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows update you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing If you need to use safe mode to remove or disable components, restart computer, press F8 to select Advanced startup options & select safe mode Technical information : Stop : 0X0000007A Atapi.sp – Address F834B50C base at F833E000,datatamp 4802539d Begin dump of physical memory “ |
#3
|
|||
|
|||
Kernel stack inpage error:0x0000007A & kernel data inpage erro
Dear Peter,
Thank you very much for your reply To resolve the problem, is it that I follow the instructions through the link given by you that is to resolve any bad block problem, do autochk, any defective hardware, any failing RAM etc Thank you & Best Regards "Peter Foldes" wrote: See the following http://msdn.microsoft.com/en-gb/library/ms793989.aspx -- Peter Please Reply to Newsgroup for the benefit of others Requests for assistance by email can not and will not be acknowledged. "123noanser" wrote in message ... Recently I have these 2 error messages every time after using my computer for awhile. After the error message had shown, it will then shut down & reboot itself May I know what’s wrong with my computer & how do I solve this problem ? Can someone please advise. I need to resolve these quickly. Please response Error Message from computer : “A problem has been detected and Windows has been shut down to prevent damage to your computer” Kernel stack inpage error If this is the first time you have seen this stop error screen, restart your computer. If this screen appear again, follow these steps : Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows update you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing If you need to use safe mode to remove or disable components, restart computer, press F8 to select Advanced startup options & select safe mode Technical information : Stop : 0X0000007A (0xc000000E,0xc000000E,0x00000….0x0B862000) Begin dump of physical memory “ orError Message from computer : “A problem has been detected and Windows has been shut down to prevent damage to your computer” Kernel data inpage error If this is the first time you have seen this stop error screen, restart your computer. If this screen appear again, follow these steps : Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows update you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing If you need to use safe mode to remove or disable components, restart computer, press F8 to select Advanced startup options & select safe mode Technical information : Stop : 0X0000007A Atapi.sp – Address F834B50C base at F833E000,datatamp 4802539d Begin dump of physical memory “ |
#4
|
|||
|
|||
Kernel stack inpage error:0x0000007A & kernel data inpage erro
http://aumha.org/a/stop.php#0x7a
-- Peter Please Reply to Newsgroup for the benefit of others Requests for assistance by email can not and will not be acknowledged. "123noanser" wrote in message ... Dear Peter, Thank you very much for your reply To resolve the problem, is it that I follow the instructions through the link given by you that is to resolve any bad block problem, do autochk, any defective hardware, any failing RAM etc Thank you & Best Regards "Peter Foldes" wrote: See the following http://msdn.microsoft.com/en-gb/library/ms793989.aspx -- Peter Please Reply to Newsgroup for the benefit of others Requests for assistance by email can not and will not be acknowledged. "123noanser" wrote in message ... Recently I have these 2 error messages every time after using my computer for awhile. After the error message had shown, it will then shut down & reboot itself May I know what’s wrong with my computer & how do I solve this problem ? Can someone please advise. I need to resolve these quickly. Please response Error Message from computer : “A problem has been detected and Windows has been shut down to prevent damage to your computer” Kernel stack inpage error If this is the first time you have seen this stop error screen, restart your computer. If this screen appear again, follow these steps : Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows update you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing If you need to use safe mode to remove or disable components, restart computer, press F8 to select Advanced startup options & select safe mode Technical information : Stop : 0X0000007A (0xc000000E,0xc000000E,0x00000….0x0B862000) Begin dump of physical memory “ orError Message from computer : “A problem has been detected and Windows has been shut down to prevent damage to your computer” Kernel data inpage error If this is the first time you have seen this stop error screen, restart your computer. If this screen appear again, follow these steps : Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows update you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing If you need to use safe mode to remove or disable components, restart computer, press F8 to select Advanced startup options & select safe mode Technical information : Stop : 0X0000007A Atapi.sp – Address F834B50C base at F833E000,datatamp 4802539d Begin dump of physical memory “ |
#5
|
|||
|
|||
Kernel stack inpage error:0x0000007A & kernel data inpage error:0x
On Thursday, 13 August 2009 13:25:01 UTC+8, 123noanser wrote:
Recently I have these 2 error messages every time after using my computer for awhile. After the error message had shown, it will then shut down & reboot itself May I know what’s wrong with my computer & how do I solve this problem ? Can someone please advise. I need to resolve these quickly. Please response Error Message from computer : “A problem has been detected and Windows has been shut down to prevent damage to your computer” Kernel stack inpage error If this is the first time you have seen this stop error screen, restart your computer. If this screen appear again, follow these steps : Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows update you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing If you need to use safe mode to remove or disable components, restart computer, press F8 to select Advanced startup options & select safe mode Technical information : Stop : 0X0000007A (0xc000000E,0xc000000E,0x00000….0x0B862000) Begin dump of physical memory “ orError Message from computer : “A problem has been detected and Windows has been shut down to prevent damage to your computer” Kernel data inpage error If this is the first time you have seen this stop error screen, restart your computer. If this screen appear again, follow these steps : Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows update you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing If you need to use safe mode to remove or disable components, restart computer, press F8 to select Advanced startup options & select safe mode Technical information : Stop : 0X0000007A Atapi.sp – Address F834B50C base at F833E000,datatamp 4802539d Begin dump of physical memory “ ------------------ Before doing more complex troubleshooting you may first check your hardware for any defect. https://www.errorsolutions.tech/erro...-inpage-error/ Solution 1.Test Hard disk drive (HDD) Solution 2.Test Random-access memory (RAM) |
Thread Tools | |
Display Modes | |
|
|