If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
16 bit Windows Subsystem
"Rock" wrote: Chris wrote: For some reason, I get a warning stating that C:\WINDOWS\SYSTEM32\AUTOEXEC.NT. The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. when i try to open certain programs that used to work on my computer or work on other computers with windows xp. If someone has any idea as to how i could fix this it'd be greatly appreciated. Thankyou I'm having trouble opening up a program from a cd rom . I never used to have trouble. I am getting an error message. "16 bit windows subsystem config.nt The system file is not suitable for running MS-Dos or Microsoft Window applications.Choose close to terminate this application." Anybody know how I can fix this? DO I NEED TO COPY MY CONFIG.NT FROM THE WINDOWS XP SOFTWARE THAT CAME FROM MY SYSTEM ? HOW DO I DO THIS? CHORD THE FOLLOWING WAS A CUT AND PASTE FROM MICROSOFT. LOOK AT MY QUESTION CHORD 16-bit MS-DOS Subsystem path to the program that you are trying to start or install C:\Winnt\System32\config.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. 16-bit MS-DOS Subsystem path to the program that you are trying to start or install config.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. 16-bit MS-DOS Subsystem path to the program that you are trying to start or install C:\Windows\System32\Autoexec.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. Although you may be prompted to quit the program or ignore the error message, either selection makes the program quit. CAUSE This issue may occur if one or more of the following files are missing or damaged: • Config.nt • Autoexec.nt • Command.com RESOLUTION MY QUESTION DO I USE MY WINDOWS XP SOFTWARE AND COPY THE CONFIG.NT FROM THERE? Chord To resolve this issue: 1. Insert the CD into the CD drive or DVD drive. 2. Click Start, and then click Run. 3. In the Open box, type cmd, and then click OK. 4. At the command prompt, type the following commands, pressing ENTER after each command: expand CD-ROM Drive Letter:\i386\config.nt_ c:\windows\system32\config.nt expand CD-ROM Drive Letter:\i386\autoexec.nt_ c:\windows\system32\autoexec.nt expand CD-ROM Drive Letter:\i386\command.co_ c:\windows\system32\command.com exit 5. Start or install the program. If the issue is resolved, do not complete the remaining steps. If the issue is not resolved, go to the next step. 6. Note: The Command.com file is not edited or created in this in the following process. Because of this, you may have to expand it from your Windows XP CD-ROM. Start Notepad. 7. In Notepad, type the following entries: dos=high, umb device=%SYSTEMROOT%\system32\himem.sys files=40 8. On the File menu, click Save As. 9. In the File Name box, type Config.nt, and then click Save. Close the Config.nt file. 10. On the File menu, click New. 11. In the new blank document, type the following entries: @echo off lh %SYSTEMROOT%\system32\mscdexnt.exe lh %SYSTEMROOT%\system32\redir lh %SYSTEMROOT%\system32\dosx SET BLASTER=A220 I5 D1 P330 T3 12. On the File menu, click Save As. 13. In the File Name box, type Autoexec.nt, and then click Save. Close the Autoexec.nt file. 14. Start Windows Explorer. Locate the Config.nt file, right-click the Config.nt file, and then click Copy. 15. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 16. Locate the Autoexec.nt file, right-click the Autoexec.nt file, and then click Copy. 17. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 18. Locate the Command.com file, right-click the expanded Command.com file, and then click Copy. 19. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. Restart your computer. If the issue continues to occur, copy the Autoexec.nt and Config.nt files from the Repair folder in Windows to the System folder. To do so, follow these steps: 1. Click Start, click Run, type c:\windows\repair, and then click OK. 2. Right-click autoexec.nt, and then click Copy. 3. Click Start, click Run, type c:\windows\system32, and then click OK. 4. Right-click anywhere in that folder, and then click Paste. 5. Right-click the Autoexect.nt file that you just copied, and then click Properties. 6. Click to select Read-Only, and then click OK. 7. Repeat steps 1 through 6 to copy the Config.nt file. Note You must enable Read-Only permissions or the files will be removed after you restart Windows. MORE INFORMATION For more information about MS-DOS-based programs in Windows, click the following article numbers to view the articles in the Microsoft Knowledge Base: 305521 (http://support.microsoft.com/kb/305521/) "16-bit MS-DOS Subsystem" error message when you run an MS-DOS or 16-Bit Windows program in Windows Server 2003 or Windows 2000 Server 314106 (http://support.microsoft.com/kb/314106/) Troubleshooting MS-DOS-based programs in Windows XP -------------------------------------------------------------------------------- APPLIES TO • Microsoft Windows XP Professional • Microsoft Windows XP Home Edition Back to the top From Chord Error message when you install or start an MS-DOS or 16-bit Windows-based program http://support.microsoft.com/?id=324767 Also can be caused by a Trojan installing a file windupdater.exe and creating registry entries for that file. http://groups.google.com/groups?selm...g. google.com AVAST (free antivirus software) can be the cause if SP2 is installed: http://groups.google.com/groups?selm...%40comcast.com You can put back the standard version of autoexec.nt by copying a backup copy held in windows\repair to windows\system32. |
Ads |
#2
|
|||
|
|||
16 bit Windows Subsystem
Seems to be an epidemic lately....
This can be caused by a trojan/virus/worm. Get rid of the trojan/virus/worm. Update your antivirus software and run a full system scan. Update whatever anti-spyware applications that you have and run a full system scan with each one. Copy the autoexec.nt file from C:\Windows\Repair to C:\Windows\System32 And set Attributes for autoexec.nt to Read-only. Or %systemroot%\Repair to %systemroot%\System32 Read-only [[Specifies whether this file is read-only, which means that it cannot be changed or accidentally deleted.]] 1. Right click the file. 2. Properties. 3. Select: Read-only. 4. Click: Apply. 5. Click: OK. 16-bit MS-DOS Subsystem error while installing or running a DOS application http://windowsxp.mvps.org/16bit.htm MS-DOS or 16-bit Windows-based program Error Message http://www.kellys-korner-xp.com/xp_m.htm#16bit Error message when you install or start an MS-DOS or 16-bit Windows-based program http://support.microsoft.com/default...b;en-us;324767 "16 Bit MS-DOS Subsystem" Error Message When You Install a Program http://support.microsoft.com/default...b;en-us;314452 Troubleshooting MS-DOS-based programs in Windows XP http://support.microsoft.com/default...b;en-us;314106 -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , chord hunted and pecked: "Rock" wrote: Chris wrote: For some reason, I get a warning stating that C:\WINDOWS\SYSTEM32\AUTOEXEC.NT. The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. when i try to open certain programs that used to work on my computer or work on other computers with windows xp. If someone has any idea as to how i could fix this it'd be greatly appreciated. Thankyou I'm having trouble opening up a program from a cd rom . I never used to have trouble. I am getting an error message. "16 bit windows subsystem config.nt The system file is not suitable for running MS-Dos or Microsoft Window applications.Choose close to terminate this application." Anybody know how I can fix this? DO I NEED TO COPY MY CONFIG.NT FROM THE WINDOWS XP SOFTWARE THAT CAME FROM MY SYSTEM ? HOW DO I DO THIS? CHORD THE FOLLOWING WAS A CUT AND PASTE FROM MICROSOFT. LOOK AT MY QUESTION CHORD 16-bit MS-DOS Subsystem path to the program that you are trying to start or install C:\Winnt\System32\config.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. 16-bit MS-DOS Subsystem path to the program that you are trying to start or install config.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. 16-bit MS-DOS Subsystem path to the program that you are trying to start or install C:\Windows\System32\Autoexec.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. Although you may be prompted to quit the program or ignore the error message, either selection makes the program quit. CAUSE This issue may occur if one or more of the following files are missing or damaged: • Config.nt • Autoexec.nt • Command.com RESOLUTION MY QUESTION DO I USE MY WINDOWS XP SOFTWARE AND COPY THE CONFIG.NT FROM THERE? Chord To resolve this issue: 1. Insert the CD into the CD drive or DVD drive. 2. Click Start, and then click Run. 3. In the Open box, type cmd, and then click OK. 4. At the command prompt, type the following commands, pressing ENTER after each command: expand CD-ROM Drive Letter:\i386\config.nt_ c:\windows\system32\config.nt expand CD-ROM Drive Letter:\i386\autoexec.nt_ c:\windows\system32\autoexec.nt expand CD-ROM Drive Letter:\i386\command.co_ c:\windows\system32\command.com exit 5. Start or install the program. If the issue is resolved, do not complete the remaining steps. If the issue is not resolved, go to the next step. 6. Note: The Command.com file is not edited or created in this in the following process. Because of this, you may have to expand it from your Windows XP CD-ROM. Start Notepad. 7. In Notepad, type the following entries: dos=high, umb device=%SYSTEMROOT%\system32\himem.sys files=40 8. On the File menu, click Save As. 9. In the File Name box, type Config.nt, and then click Save. Close the Config.nt file. 10. On the File menu, click New. 11. In the new blank document, type the following entries: @echo off lh %SYSTEMROOT%\system32\mscdexnt.exe lh %SYSTEMROOT%\system32\redir lh %SYSTEMROOT%\system32\dosx SET BLASTER=A220 I5 D1 P330 T3 12. On the File menu, click Save As. 13. In the File Name box, type Autoexec.nt, and then click Save. Close the Autoexec.nt file. 14. Start Windows Explorer. Locate the Config.nt file, right-click the Config.nt file, and then click Copy. 15. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 16. Locate the Autoexec.nt file, right-click the Autoexec.nt file, and then click Copy. 17. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 18. Locate the Command.com file, right-click the expanded Command.com file, and then click Copy. 19. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. Restart your computer. If the issue continues to occur, copy the Autoexec.nt and Config.nt files from the Repair folder in Windows to the System folder. To do so, follow these steps: 1. Click Start, click Run, type c:\windows\repair, and then click OK. 2. Right-click autoexec.nt, and then click Copy. 3. Click Start, click Run, type c:\windows\system32, and then click OK. 4. Right-click anywhere in that folder, and then click Paste. 5. Right-click the Autoexect.nt file that you just copied, and then click Properties. 6. Click to select Read-Only, and then click OK. 7. Repeat steps 1 through 6 to copy the Config.nt file. Note You must enable Read-Only permissions or the files will be removed after you restart Windows. MORE INFORMATION For more information about MS-DOS-based programs in Windows, click the following article numbers to view the articles in the Microsoft Knowledge Base: 305521 (http://support.microsoft.com/kb/305521/) "16-bit MS-DOS Subsystem" error message when you run an MS-DOS or 16-Bit Windows program in Windows Server 2003 or Windows 2000 Server 314106 (http://support.microsoft.com/kb/314106/) Troubleshooting MS-DOS-based programs in Windows XP -------------------------------------------------------------------------- ------ APPLIES TO • Microsoft Windows XP Professional • Microsoft Windows XP Home Edition Back to the top From Chord Error message when you install or start an MS-DOS or 16-bit Windows-based program http://support.microsoft.com/?id=324767 Also can be caused by a Trojan installing a file windupdater.exe and creating registry entries for that file. http://groups.google.com/groups?selm...g. google.com AVAST (free antivirus software) can be the cause if SP2 is installed: http://groups.google.com/groups?selm...%40comcast.com You can put back the standard version of autoexec.nt by copying a backup copy held in windows\repair to windows\system32. |
#3
|
|||
|
|||
16 bit Windows Subsystem
"Wesley Vogel" wrote: Seems to be an epidemic lately.... This can be caused by a trojan/virus/worm. Get rid of the trojan/virus/worm. Update your antivirus software and run a full system scan. Update whatever anti-spyware applications that you have and run a full system scan with each one. Copy the autoexec.nt file from C:\Windows\Repair to C:\Windows\System32 And set Attributes for autoexec.nt to Read-only. Or %systemroot%\Repair to %systemroot%\System32 Read-only [[Specifies whether this file is read-only, which means that it cannot be changed or accidentally deleted.]] 1. Right click the file. 2. Properties. 3. Select: Read-only. 4. Click: Apply. 5. Click: OK. 16-bit MS-DOS Subsystem error while installing or running a DOS application http://windowsxp.mvps.org/16bit.htm MS-DOS or 16-bit Windows-based program Error Message http://www.kellys-korner-xp.com/xp_m.htm#16bit Error message when you install or start an MS-DOS or 16-bit Windows-based program http://support.microsoft.com/default...b;en-us;324767 "16 Bit MS-DOS Subsystem" Error Message When You Install a Program http://support.microsoft.com/default...b;en-us;314452 Troubleshooting MS-DOS-based programs in Windows XP http://support.microsoft.com/default...b;en-us;314106 -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , chord hunted and pecked: "Rock" wrote: Thankyou I'm having trouble opening up a program from a cd rom . I never used to have trouble. I am getting an error message. "16 bit windows subsystem config.nt The system file is not suitable for running MS-Dos or Microsoft Window applications.Choose close to terminate this application." Anybody know how I can fix this? DO I NEED TO COPY MY CONFIG.NT FROM THE WINDOWS XP SOFTWARE THAT CAME FROM MY SYSTEM ? HOW DO I DO THIS? CHORD THE FOLLOWING WAS A CUT AND PASTE FROM MICROSOFT. LOOK AT MY QUESTION CHORD 16-bit MS-DOS Subsystem path to the program that you are trying to start or install C:\Winnt\System32\config.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. 16-bit MS-DOS Subsystem path to the program that you are trying to start or install config.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. 16-bit MS-DOS Subsystem path to the program that you are trying to start or install C:\Windows\System32\Autoexec.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. Although you may be prompted to quit the program or ignore the error message, either selection makes the program quit. CAUSE This issue may occur if one or more of the following files are missing or damaged: • Config.nt • Autoexec.nt • Command.com RESOLUTION MY QUESTION DO I USE MY WINDOWS XP SOFTWARE AND COPY THE CONFIG.NT FROM THERE? Chord To resolve this issue: 1. Insert the CD into the CD drive or DVD drive. 2. Click Start, and then click Run. 3. In the Open box, type cmd, and then click OK. 4. At the command prompt, type the following commands, pressing ENTER after each command: expand CD-ROM Drive Letter:\i386\config.nt_ c:\windows\system32\config.nt expand CD-ROM Drive Letter:\i386\autoexec.nt_ c:\windows\system32\autoexec.nt expand CD-ROM Drive Letter:\i386\command.co_ c:\windows\system32\command.com exit 5. Start or install the program. If the issue is resolved, do not complete the remaining steps. If the issue is not resolved, go to the next step. 6. Note: The Command.com file is not edited or created in this in the following process. Because of this, you may have to expand it from your Windows XP CD-ROM. Start Notepad. 7. In Notepad, type the following entries: dos=high, umb device=%SYSTEMROOT%\system32\himem.sys files=40 8. On the File menu, click Save As. 9. In the File Name box, type Config.nt, and then click Save. Close the Config.nt file. 10. On the File menu, click New. 11. In the new blank document, type the following entries: @echo off lh %SYSTEMROOT%\system32\mscdexnt.exe lh %SYSTEMROOT%\system32\redir lh %SYSTEMROOT%\system32\dosx SET BLASTER=A220 I5 D1 P330 T3 12. On the File menu, click Save As. 13. In the File Name box, type Autoexec.nt, and then click Save. Close the Autoexec.nt file. 14. Start Windows Explorer. Locate the Config.nt file, right-click the Config.nt file, and then click Copy. 15. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 16. Locate the Autoexec.nt file, right-click the Autoexec.nt file, and then click Copy. 17. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 18. Locate the Command.com file, right-click the expanded Command.com file, and then click Copy. 19. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. Restart your computer. If the issue continues to occur, copy the Autoexec.nt and Config.nt files from the Repair folder in Windows to the System folder. To do so, follow these steps: 1. Click Start, click Run, type c:\windows\repair, and then click OK. 2. Right-click autoexec.nt, and then click Copy. 3. Click Start, click Run, type c:\windows\system32, and then click OK. 4. Right-click anywhere in that folder, and then click Paste. 5. Right-click the Autoexect.nt file that you just copied, and then click Properties. 6. Click to select Read-Only, and then click OK. 7. Repeat steps 1 through 6 to copy the Config.nt file. Note You must enable Read-Only permissions or the files will be removed after you restart Windows. MORE INFORMATION For more information about MS-DOS-based programs in Windows, click the following article numbers to view the articles in the Microsoft Knowledge Base: 305521 (http://support.microsoft.com/kb/305521/) "16-bit MS-DOS Subsystem" error message when you run an MS-DOS or 16-Bit Windows program in Windows Server 2003 or Windows 2000 Server 314106 (http://support.microsoft.com/kb/314106/) Troubleshooting MS-DOS-based programs in Windows XP -------------------------------------------------------------------------- ------ APPLIES TO • Microsoft Windows XP Professional • Microsoft Windows XP Home Edition Back to the top From Chord Error message when you install or start an MS-DOS or 16-bit Windows-based program http://support.microsoft.com/?id=324767 Also can be caused by a Trojan installing a file windupdater.exe and creating registry entries for that file. http://groups.google.com/groups?selm...g. google.com AVAST (free antivirus software) can be the cause if SP2 is installed: http://groups.google.com/groups?selm...%40comcast.com You can put back the standard version of autoexec.nt by copying a backup copy held in windows\repair to windows\system32. |
#4
|
|||
|
|||
16 bit Windows Subsystem
If there was a reply in there, I couldn't decipher it.
-- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , chord hunted and pecked: "Wesley Vogel" wrote: Seems to be an epidemic lately.... This can be caused by a trojan/virus/worm. Get rid of the trojan/virus/worm. Update your antivirus software and run a full system scan. Update whatever anti-spyware applications that you have and run a full system scan with each one. Copy the autoexec.nt file from C:\Windows\Repair to C:\Windows\System32 And set Attributes for autoexec.nt to Read-only. Or %systemroot%\Repair to %systemroot%\System32 Read-only [[Specifies whether this file is read-only, which means that it cannot be changed or accidentally deleted.]] 1. Right click the file. 2. Properties. 3. Select: Read-only. 4. Click: Apply. 5. Click: OK. 16-bit MS-DOS Subsystem error while installing or running a DOS application http://windowsxp.mvps.org/16bit.htm MS-DOS or 16-bit Windows-based program Error Message http://www.kellys-korner-xp.com/xp_m.htm#16bit Error message when you install or start an MS-DOS or 16-bit Windows-based program http://support.microsoft.com/default...b;en-us;324767 "16 Bit MS-DOS Subsystem" Error Message When You Install a Program http://support.microsoft.com/default...b;en-us;314452 Troubleshooting MS-DOS-based programs in Windows XP http://support.microsoft.com/default...b;en-us;314106 -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , chord hunted and pecked: "Rock" wrote: Thankyou I'm having trouble opening up a program from a cd rom . I never used to have trouble. I am getting an error message. "16 bit windows subsystem config.nt The system file is not suitable for running MS-Dos or Microsoft Window applications.Choose close to terminate this application." Anybody know how I can fix this? DO I NEED TO COPY MY CONFIG.NT FROM THE WINDOWS XP SOFTWARE THAT CAME FROM MY SYSTEM ? HOW DO I DO THIS? CHORD THE FOLLOWING WAS A CUT AND PASTE FROM MICROSOFT. LOOK AT MY QUESTION CHORD 16-bit MS-DOS Subsystem path to the program that you are trying to start or install C:\Winnt\System32\config.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. 16-bit MS-DOS Subsystem path to the program that you are trying to start or install config.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. 16-bit MS-DOS Subsystem path to the program that you are trying to start or install C:\Windows\System32\Autoexec.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. Although you may be prompted to quit the program or ignore the error message, either selection makes the program quit. CAUSE This issue may occur if one or more of the following files are missing or damaged: • Config.nt • Autoexec.nt • Command.com RESOLUTION MY QUESTION DO I USE MY WINDOWS XP SOFTWARE AND COPY THE CONFIG.NT FROM THERE? Chord To resolve this issue: 1. Insert the CD into the CD drive or DVD drive. 2. Click Start, and then click Run. 3. In the Open box, type cmd, and then click OK. 4. At the command prompt, type the following commands, pressing ENTER after each command: expand CD-ROM Drive Letter:\i386\config.nt_ c:\windows\system32\config.nt expand CD-ROM Drive Letter:\i386\autoexec.nt_ c:\windows\system32\autoexec.nt expand CD-ROM Drive Letter:\i386\command.co_ c:\windows\system32\command.com exit 5. Start or install the program. If the issue is resolved, do not complete the remaining steps. If the issue is not resolved, go to the next step. 6. Note: The Command.com file is not edited or created in this in the following process. Because of this, you may have to expand it from your Windows XP CD-ROM. Start Notepad. 7. In Notepad, type the following entries: dos=high, umb device=%SYSTEMROOT%\system32\himem.sys files=40 8. On the File menu, click Save As. 9. In the File Name box, type Config.nt, and then click Save. Close the Config.nt file. 10. On the File menu, click New. 11. In the new blank document, type the following entries: @echo off lh %SYSTEMROOT%\system32\mscdexnt.exe lh %SYSTEMROOT%\system32\redir lh %SYSTEMROOT%\system32\dosx SET BLASTER=A220 I5 D1 P330 T3 12. On the File menu, click Save As. 13. In the File Name box, type Autoexec.nt, and then click Save. Close the Autoexec.nt file. 14. Start Windows Explorer. Locate the Config.nt file, right-click the Config.nt file, and then click Copy. 15. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 16. Locate the Autoexec.nt file, right-click the Autoexec.nt file, and then click Copy. 17. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 18. Locate the Command.com file, right-click the expanded Command.com file, and then click Copy. 19. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. Restart your computer. If the issue continues to occur, copy the Autoexec.nt and Config.nt files from the Repair folder in Windows to the System folder. To do so, follow these steps: 1. Click Start, click Run, type c:\windows\repair, and then click OK. 2. Right-click autoexec.nt, and then click Copy. 3. Click Start, click Run, type c:\windows\system32, and then click OK. 4. Right-click anywhere in that folder, and then click Paste. 5. Right-click the Autoexect.nt file that you just copied, and then click Properties. 6. Click to select Read-Only, and then click OK. 7. Repeat steps 1 through 6 to copy the Config.nt file. Note You must enable Read-Only permissions or the files will be removed after you restart Windows. MORE INFORMATION For more information about MS-DOS-based programs in Windows, click the following article numbers to view the articles in the Microsoft Knowledge Base: 305521 (http://support.microsoft.com/kb/305521/) "16-bit MS-DOS Subsystem" error message when you run an MS-DOS or 16-Bit Windows program in Windows Server 2003 or Windows 2000 Server 314106 (http://support.microsoft.com/kb/314106/) Troubleshooting MS-DOS-based programs in Windows XP ------------------------------------------------------------------------ -- ------ APPLIES TO • Microsoft Windows XP Professional • Microsoft Windows XP Home Edition Back to the top From Chord Error message when you install or start an MS-DOS or 16-bit Windows-based program http://support.microsoft.com/?id=324767 Also can be caused by a Trojan installing a file windupdater.exe and creating registry entries for that file. http://groups.google.com/groups?selm...g. google.com AVAST (free antivirus software) can be the cause if SP2 is installed: http://groups.google.com/groups?selm...%40comcast.com You can put back the standard version of autoexec.nt by copying a backup copy held in windows\repair to windows\system32. |
#5
|
|||
|
|||
16 bit Windows Subsystem
"Wesley Vogel" wrote: If there was a reply in there, I couldn't decipher it. -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User I got rid of the old error message. Now I have a new one, NTVDM KERNAL missing 16 bit system module. What I did was download the autoexec.nt,command.nt and config.nt. and unzipped them and extracted them to windows folder. Seems like the only file copied was auto.exe. Tell me what do to. I want to be able to run my programs. Chord In , chord hunted and pecked: "Wesley Vogel" wrote: Seems to be an epidemic lately.... This can be caused by a trojan/virus/worm. Get rid of the trojan/virus/worm. Update your antivirus software and run a full system scan. Update whatever anti-spyware applications that you have and run a full system scan with each one. Copy the autoexec.nt file from C:\Windows\Repair to C:\Windows\System32 And set Attributes for autoexec.nt to Read-only. Or %systemroot%\Repair to %systemroot%\System32 Read-only [[Specifies whether this file is read-only, which means that it cannot be changed or accidentally deleted.]] 1. Right click the file. 2. Properties. 3. Select: Read-only. 4. Click: Apply. 5. Click: OK. 16-bit MS-DOS Subsystem error while installing or running a DOS application http://windowsxp.mvps.org/16bit.htm MS-DOS or 16-bit Windows-based program Error Message http://www.kellys-korner-xp.com/xp_m.htm#16bit Error message when you install or start an MS-DOS or 16-bit Windows-based program http://support.microsoft.com/default...b;en-us;324767 "16 Bit MS-DOS Subsystem" Error Message When You Install a Program http://support.microsoft.com/default...b;en-us;314452 Troubleshooting MS-DOS-based programs in Windows XP http://support.microsoft.com/default...b;en-us;314106 -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , chord hunted and pecked: "Rock" wrote: Thankyou I'm having trouble opening up a program from a cd rom . I never used to have trouble. I am getting an error message. "16 bit windows subsystem config.nt The system file is not suitable for running MS-Dos or Microsoft Window applications.Choose close to terminate this application." Anybody know how I can fix this? DO I NEED TO COPY MY CONFIG.NT FROM THE WINDOWS XP SOFTWARE THAT CAME FROM MY SYSTEM ? HOW DO I DO THIS? CHORD THE FOLLOWING WAS A CUT AND PASTE FROM MICROSOFT. LOOK AT MY QUESTION CHORD 16-bit MS-DOS Subsystem path to the program that you are trying to start or install C:\Winnt\System32\config.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. 16-bit MS-DOS Subsystem path to the program that you are trying to start or install config.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. 16-bit MS-DOS Subsystem path to the program that you are trying to start or install C:\Windows\System32\Autoexec.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. Although you may be prompted to quit the program or ignore the error message, either selection makes the program quit. CAUSE This issue may occur if one or more of the following files are missing or damaged: • Config.nt • Autoexec.nt • Command.com RESOLUTION MY QUESTION DO I USE MY WINDOWS XP SOFTWARE AND COPY THE CONFIG.NT FROM THERE? Chord To resolve this issue: 1. Insert the CD into the CD drive or DVD drive. 2. Click Start, and then click Run. 3. In the Open box, type cmd, and then click OK. 4. At the command prompt, type the following commands, pressing ENTER after each command: expand CD-ROM Drive Letter:\i386\config.nt_ c:\windows\system32\config.nt expand CD-ROM Drive Letter:\i386\autoexec.nt_ c:\windows\system32\autoexec.nt expand CD-ROM Drive Letter:\i386\command.co_ c:\windows\system32\command.com exit 5. Start or install the program. If the issue is resolved, do not complete the remaining steps. If the issue is not resolved, go to the next step. 6. Note: The Command.com file is not edited or created in this in the following process. Because of this, you may have to expand it from your Windows XP CD-ROM. Start Notepad. 7. In Notepad, type the following entries: dos=high, umb device=%SYSTEMROOT%\system32\himem.sys files=40 8. On the File menu, click Save As. 9. In the File Name box, type Config.nt, and then click Save. Close the Config.nt file. 10. On the File menu, click New. 11. In the new blank document, type the following entries: @echo off lh %SYSTEMROOT%\system32\mscdexnt.exe lh %SYSTEMROOT%\system32\redir lh %SYSTEMROOT%\system32\dosx SET BLASTER=A220 I5 D1 P330 T3 12. On the File menu, click Save As. 13. In the File Name box, type Autoexec.nt, and then click Save. Close the Autoexec.nt file. 14. Start Windows Explorer. Locate the Config.nt file, right-click the Config.nt file, and then click Copy. 15. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 16. Locate the Autoexec.nt file, right-click the Autoexec.nt file, and then click Copy. 17. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 18. Locate the Command.com file, right-click the expanded Command.com file, and then click Copy. 19. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. Restart your computer. If the issue continues to occur, copy the Autoexec.nt and Config.nt files from the Repair folder in Windows to the System folder. To do so, follow these steps: 1. Click Start, click Run, type c:\windows\repair, and then click OK. 2. Right-click autoexec.nt, and then click Copy. 3. Click Start, click Run, type c:\windows\system32, and then click OK. 4. Right-click anywhere in that folder, and then click Paste. 5. Right-click the Autoexect.nt file that you just copied, and then click Properties. 6. Click to select Read-Only, and then click OK. 7. Repeat steps 1 through 6 to copy the Config.nt file. Note You must enable Read-Only permissions or the files will be removed after you restart Windows. MORE INFORMATION For more information about MS-DOS-based programs in Windows, click the following article numbers to view the articles in the Microsoft Knowledge Base: 305521 (http://support.microsoft.com/kb/305521/) "16-bit MS-DOS Subsystem" error message when you run an MS-DOS or 16-Bit Windows program in Windows Server 2003 or Windows 2000 Server 314106 (http://support.microsoft.com/kb/314106/) Troubleshooting MS-DOS-based programs in Windows XP ------------------------------------------------------------------------ -- ------ APPLIES TO • Microsoft Windows XP Professional • Microsoft Windows XP Home Edition Back to the top From Chord Error message when you install or start an MS-DOS or 16-bit Windows-based program http://support.microsoft.com/?id=324767 Also can be caused by a Trojan installing a file windupdater.exe and creating registry entries for that file. http://groups.google.com/groups?selm...g. google.com AVAST (free antivirus software) can be the cause if SP2 is installed: http://groups.google.com/groups?selm...%40comcast.com You can put back the standard version of autoexec.nt by copying a backup copy held in windows\repair to windows\system32. |
#6
|
|||
|
|||
16 bit Windows Subsystem
Chord,
The first thing that you want to do is get rid of any malware that you might have on your machine. Update your antivirus software and run a full system scan. Update whatever anti-spyware applications that you have and run a full system scan with each one. NTVDM KERNEL: missing 16-bit system module please re-install the following module to your system32 directory: name of missing file What is the name of the missing file or module in the NTVDM KERNEL error message? NTVDM is NTVDM.exe it is the NT Virtual DOS Machine. NTVDM.exe runs old 16-bit applications. What is the name of the program that you are trying to run from your CD? Is it an old MS-DOS program? None of these 16-bit error messages should be popping up if you are trying to run a modern program. You should run the System File Checker (sfc.exe) it replaces screwed up system files. Load your XP CD in your CD drive. Start | Run | Type or paste: sfc /scannow | Click OK If you have XP Home and it asks for your XP Pro CD, see this KB article... You may be prompted to insert a Windows XP Professional CD when you run the System File Checker tool in Windows XP Home Edition http://support.microsoft.com/default...b;en-us;897128 If SFC.EXE did anything it will be in the Event Viewer. Open the Event Viewer... Start | Run | Type: eventvwr | Click OK | Click System | Look at any Windows File Protection entries Explains a whole bunch about sfc.exe. scannow sfc (sfc.exe) http://www.updatexp.com/scannow-sfc.html -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , chord hunted and pecked: "Wesley Vogel" wrote: If there was a reply in there, I couldn't decipher it. -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User I got rid of the old error message. Now I have a new one, NTVDM KERNAL missing 16 bit system module. What I did was download the autoexec.nt,command.nt and config.nt. and unzipped them and extracted them to windows folder. Seems like the only file copied was auto.exe. Tell me what do to. I want to be able to run my programs. Chord In , chord hunted and pecked: "Wesley Vogel" wrote: Seems to be an epidemic lately.... This can be caused by a trojan/virus/worm. Get rid of the trojan/virus/worm. Update your antivirus software and run a full system scan. Update whatever anti-spyware applications that you have and run a full system scan with each one. Copy the autoexec.nt file from C:\Windows\Repair to C:\Windows\System32 And set Attributes for autoexec.nt to Read-only. Or %systemroot%\Repair to %systemroot%\System32 Read-only [[Specifies whether this file is read-only, which means that it cannot be changed or accidentally deleted.]] 1. Right click the file. 2. Properties. 3. Select: Read-only. 4. Click: Apply. 5. Click: OK. 16-bit MS-DOS Subsystem error while installing or running a DOS application http://windowsxp.mvps.org/16bit.htm MS-DOS or 16-bit Windows-based program Error Message http://www.kellys-korner-xp.com/xp_m.htm#16bit Error message when you install or start an MS-DOS or 16-bit Windows-based program http://support.microsoft.com/default...b;en-us;324767 "16 Bit MS-DOS Subsystem" Error Message When You Install a Program http://support.microsoft.com/default...b;en-us;314452 Troubleshooting MS-DOS-based programs in Windows XP http://support.microsoft.com/default...b;en-us;314106 -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User In , chord hunted and pecked: "Rock" wrote: Thankyou I'm having trouble opening up a program from a cd rom . I never used to have trouble. I am getting an error message. "16 bit windows subsystem config.nt The system file is not suitable for running MS-Dos or Microsoft Window applications.Choose close to terminate this application." Anybody know how I can fix this? DO I NEED TO COPY MY CONFIG.NT FROM THE WINDOWS XP SOFTWARE THAT CAME FROM MY SYSTEM ? HOW DO I DO THIS? CHORD THE FOLLOWING WAS A CUT AND PASTE FROM MICROSOFT. LOOK AT MY QUESTION CHORD 16-bit MS-DOS Subsystem path to the program that you are trying to start or install C:\Winnt\System32\config.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. 16-bit MS-DOS Subsystem path to the program that you are trying to start or install config.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. 16-bit MS-DOS Subsystem path to the program that you are trying to start or install C:\Windows\System32\Autoexec.nt The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. Although you may be prompted to quit the program or ignore the error message, either selection makes the program quit. CAUSE This issue may occur if one or more of the following files are missing or damaged: • Config.nt • Autoexec.nt • Command.com RESOLUTION MY QUESTION DO I USE MY WINDOWS XP SOFTWARE AND COPY THE CONFIG.NT FROM THERE? Chord To resolve this issue: 1. Insert the CD into the CD drive or DVD drive. 2. Click Start, and then click Run. 3. In the Open box, type cmd, and then click OK. 4. At the command prompt, type the following commands, pressing ENTER after each command: expand CD-ROM Drive Letter:\i386\config.nt_ c:\windows\system32\config.nt expand CD-ROM Drive Letter:\i386\autoexec.nt_ c:\windows\system32\autoexec.nt expand CD-ROM Drive Letter:\i386\command.co_ c:\windows\system32\command.com exit 5. Start or install the program. If the issue is resolved, do not complete the remaining steps. If the issue is not resolved, go to the next step. 6. Note: The Command.com file is not edited or created in this in the following process. Because of this, you may have to expand it from your Windows XP CD-ROM. Start Notepad. 7. In Notepad, type the following entries: dos=high, umb device=%SYSTEMROOT%\system32\himem.sys files=40 8. On the File menu, click Save As. 9. In the File Name box, type Config.nt, and then click Save. Close the Config.nt file. 10. On the File menu, click New. 11. In the new blank document, type the following entries: @echo off lh %SYSTEMROOT%\system32\mscdexnt.exe lh %SYSTEMROOT%\system32\redir lh %SYSTEMROOT%\system32\dosx SET BLASTER=A220 I5 D1 P330 T3 12. On the File menu, click Save As. 13. In the File Name box, type Autoexec.nt, and then click Save. Close the Autoexec.nt file. 14. Start Windows Explorer. Locate the Config.nt file, right-click the Config.nt file, and then click Copy. 15. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 16. Locate the Autoexec.nt file, right-click the Autoexec.nt file, and then click Copy. 17. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 18. Locate the Command.com file, right-click the expanded Command.com file, and then click Copy. 19. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. Restart your computer. If the issue continues to occur, copy the Autoexec.nt and Config.nt files from the Repair folder in Windows to the System folder. To do so, follow these steps: 1. Click Start, click Run, type c:\windows\repair, and then click OK. 2. Right-click autoexec.nt, and then click Copy. 3. Click Start, click Run, type c:\windows\system32, and then click OK. 4. Right-click anywhere in that folder, and then click Paste. 5. Right-click the Autoexect.nt file that you just copied, and then click Properties. 6. Click to select Read-Only, and then click OK. 7. Repeat steps 1 through 6 to copy the Config.nt file. Note You must enable Read-Only permissions or the files will be removed after you restart Windows. MORE INFORMATION For more information about MS-DOS-based programs in Windows, click the following article numbers to view the articles in the Microsoft Knowledge Base: 305521 (http://support.microsoft.com/kb/305521/) "16-bit MS-DOS Subsystem" error message when you run an MS-DOS or 16-Bit Windows program in Windows Server 2003 or Windows 2000 Server 314106 (http://support.microsoft.com/kb/314106/) Troubleshooting MS-DOS-based programs in Windows XP ---------------------------------------------------------------------- -- -- ------ APPLIES TO • Microsoft Windows XP Professional • Microsoft Windows XP Home Edition Back to the top From Chord Error message when you install or start an MS-DOS or 16-bit Windows-based program http://support.microsoft.com/?id=324767 Also can be caused by a Trojan installing a file windupdater.exe and creating registry entries for that file. http://groups.google.com/groups?selm...g. google.com AVAST (free antivirus software) can be the cause if SP2 is installed: http://groups.google.com/groups?selm...%40comcast.com You can put back the standard version of autoexec.nt by copying a backup copy held in windows\repair to windows\system32. |
#7
|
|||
|
|||
16 bit Windows Subsystem
"To Wesley Vogel" From Chord The first thing that you want to do is get rid of any malware that you might have on your machine. Update your antivirus software and run a full system scan. "I did this. No virus" Chord Update whatever anti-spyware applications that you have and run a full system scan with each one. NTVDM KERNEL: missing 16-bit system module please re-install the following module to your system32 directory: name of missing file What is the name of the missing file or module in the NTVDM KERNEL error message? NTVDM is NTVDM.exe it is the NT Virtual DOS Machine. NTVDM.exe runs old 16-bit applications. What is the name of the program that you are trying to run from your CD? Is it an old MS-DOS program? " BAND IN THE BOX 2001" Chord None of these 16-bit error messages should be popping up if you are trying to run a modern program. You should run the System File Checker (sfc.exe) it replaces screwed up system files. "I ran This" Chord Load your XP CD in your CD drive." " I did this" Start | Run | Type or paste: sfc /scannow | Click OK If you have XP Home and it asks for your XP Pro CD, see this KB article... You may be prompted to insert a Windows XP Professional CD when you run the System File Checker tool in Windows XP Home Edition http://support.microsoft.com/default...b;en-us;897128 "Wes, I was prompted to insert Windows XP Professional CD. The message was Files that are required to run properly must be copied to the dll cache. Insert you windows xp professional cd-rom -now. I keep hitting retry when this message comes up. Seems i'm going around in circles. Nothing is being done." Chord If SFC.EXE did anything it will be in the Event Viewer. Open the Event Viewer... Start | Run | Type: eventvwr | Click OK | Click System | Look at any Windows File Protection entries. " I did this. Just said Windows file protection started" Chord Explains a whole bunch about sfc.exe. scannow sfc (sfc.exe) http://www.updatexp.com/scannow-sfc.html "Wes, I made a copy of Fp40ext.inf and Ims.inf in the service pak 386 folder. Still getting errormessage please reinstall following module to your systemn 32 directory COMM.DRIVE What do I do next? anybody can help me?" Chord -- Wes MS-MVP Windows Shell/User In , chord hunted and pecked: "Wesley Vogel" wrote: If there was a reply in there, I couldn't decipher it. -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User I got rid of the old error message. Now I have a new one, NTVDM KERNAL missing 16 bit system module. What I did was download the autoexec.nt,command.nt and config.nt. and unzipped them and extracted them to windows folder. Seems like the only file copied was auto.exe. Tell me what do to. I want to be able to run my programs. Chord expand CD-ROM Drive Letter:\i386\config.nt_ c:\windows\system32\config.nt expand CD-ROM Drive Letter:\i386\autoexec.nt_ c:\windows\system32\autoexec.nt expand CD-ROM Drive Letter:\i386\command.co_ c:\windows\system32\command.com exit 5. Start or install the program. If the issue is resolved, do not complete the remaining steps. If the issue is not resolved, go to the next step. 6. Note: The Command.com file is not edited or created in this in the following process. Because of this, you may have to expand it from your Windows XP CD-ROM. Start Notepad. 7. In Notepad, type the following entries: dos=high, umb device=%SYSTEMROOT%\system32\himem.sys files=40 8. On the File menu, click Save As. 9. In the File Name box, type Config.nt, and then click Save. Close the Config.nt file. 10. On the File menu, click New. 11. In the new blank document, type the following entries: @echo off lh %SYSTEMROOT%\system32\mscdexnt.exe lh %SYSTEMROOT%\system32\redir lh %SYSTEMROOT%\system32\dosx SET BLASTER=A220 I5 D1 P330 T3 12. On the File menu, click Save As. 13. In the File Name box, type Autoexec.nt, and then click Save. Close the Autoexec.nt file. 14. Start Windows Explorer. Locate the Config.nt file, right-click the Config.nt file, and then click Copy. 15. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 16. Locate the Autoexec.nt file, right-click the Autoexec.nt file, and then click Copy. 17. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 18. Locate the Command.com file, right-click the expanded Command.com file, and then click Copy. 19. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. Restart your computer. If the issue continues to occur, copy the Autoexec.nt and Config.nt files from the Repair folder in Windows to the System folder. To do so, follow these steps: 1. Click Start, click Run, type c:\windows\repair, and then click OK. 2. Right-click autoexec.nt, and then click Copy. 3. Click Start, click Run, type c:\windows\system32, and then click OK. 4. Right-click anywhere in that folder, and then click Paste. 5. Right-click the Autoexect.nt file that you just copied, and then click Properties. 6. Click to select Read-Only, and then click OK. 7. Repeat steps 1 through 6 to copy the Config.nt file. Note You must enable Read-Only permissions or the files will be removed after you restart Windows. MORE INFORMATION For more information about MS-DOS-based programs in Windows, click the following article numbers to view the articles in the Microsoft Knowledge Base: 305521 (http://support.microsoft.com/kb/305521/) "16-bit MS-DOS Subsystem" error message when you run an MS-DOS or 16-Bit Windows program in Windows Server 2003 or Windows 2000 Server 314106 (http://support.microsoft.com/kb/314106/) Troubleshooting MS-DOS-based programs in Windows XP ---------------------------------------------------------------------- -- -- ------ APPLIES TO • Microsoft Windows XP Professional • Microsoft Windows XP Home Edition Back to the top From Chord Error message when you install or start an MS-DOS or 16-bit Windows-based program http://support.microsoft.com/?id=324767 Also can be caused by a Trojan installing a file windupdater.exe and creating registry entries for that file. http://groups.google.com/groups?selm...g. google.com |
#8
|
|||
|
|||
16 bit Windows Subsystem
"chord" wrote: "To Wesley Vogel" Never received a reply from anybody. From Chord The first thing that you want to do is get rid of any malware that you might have on your machine. Update your antivirus software and run a full system scan. "I did this. No virus" Chord Update whatever anti-spyware applications that you have and run a full system scan with each one. NTVDM KERNEL: missing 16-bit system module please re-install the following module to your system32 directory: name of missing file What is the name of the missing file or module in the NTVDM KERNEL error message? NTVDM is NTVDM.exe it is the NT Virtual DOS Machine. NTVDM.exe runs old 16-bit applications. What is the name of the program that you are trying to run from your CD? Is it an old MS-DOS program? " BAND IN THE BOX 2001" Chord None of these 16-bit error messages should be popping up if you are trying to run a modern program. You should run the System File Checker (sfc.exe) it replaces screwed up system files. "I ran This" Chord Load your XP CD in your CD drive." " I did this" Start | Run | Type or paste: sfc /scannow | Click OK If you have XP Home and it asks for your XP Pro CD, see this KB article... You may be prompted to insert a Windows XP Professional CD when you run the System File Checker tool in Windows XP Home Edition http://support.microsoft.com/default...b;en-us;897128 "Wes, I was prompted to insert Windows XP Professional CD. The message was Files that are required to run properly must be copied to the dll cache. Insert you windows xp professional cd-rom -now. I keep hitting retry when this message comes up. Seems i'm going around in circles. Nothing is being done." Chord If SFC.EXE did anything it will be in the Event Viewer. Open the Event Viewer... Start | Run | Type: eventvwr | Click OK | Click System | Look at any Windows File Protection entries. " I did this. Just said Windows file protection started" Chord Explains a whole bunch about sfc.exe. scannow sfc (sfc.exe) http://www.updatexp.com/scannow-sfc.html "Wes, I made a copy of Fp40ext.inf and Ims.inf in the service pak 386 folder. Still getting errormessage please reinstall following module to your systemn 32 directory COMM.DRIVE What do I do next? anybody can help me?" Chord -- To Wesley Vogel" From Chord The first thing that you want to do is get rid of any malware that you might have on your machine. Update your antivirus software and run a full system scan. "I did this. No virus" Chord Update whatever anti-spyware applications that you have and run a full system scan with each one. NTVDM KERNEL: missing 16-bit system module please re-install the following module to your system32 directory: name of missing file What is the name of the missing file or module in the NTVDM KERNEL error message? NTVDM is NTVDM.exe it is the NT Virtual DOS Machine. NTVDM.exe runs old 16-bit applications. What is the name of the program that you are trying to run from your CD? Is it an old MS-DOS program? " BAND IN THE BOX 2001" Chord None of these 16-bit error messages should be popping up if you are trying to run a modern program. You should run the System File Checker (sfc.exe) it replaces screwed up system files. "I ran This" Chord Load your XP CD in your CD drive." " I did this" Start | Run | Type or paste: sfc /scannow | Click OK If you have XP Home and it asks for your XP Pro CD, see this KB article... You may be prompted to insert a Windows XP Professional CD when you run the System File Checker tool in Windows XP Home Edition http://support.microsoft.com/default...b;en-us;897128 "Wes, I was prompted to insert Windows XP Professional CD. The message was Files that are required to run properly must be copied to the dll cache. Insert you windows xp professional cd-rom -now. I keep hitting retry when this message comes up. Seems i'm going around in circles. Nothing is being done." Chord If SFC.EXE did anything it will be in the Event Viewer. Open the Event Viewer... Start | Run | Type: eventvwr | Click OK | Click System | Look at any Windows File Protection entries. " I did this. Just said Windows file protection started" Chord Explains a whole bunch about sfc.exe. scannow sfc (sfc.exe) http://www.updatexp.com/scannow-sfc.html "Wes, I made a copy of Fp40ext.inf and Ims.inf in the service pak 386 folder. Still getting errormessage please reinstall following module to your systemn 32 directory COMM.DRIVE What do I do next? anybody can help me?" Chord -- Wes MS-MVP Windows Shell/User In , chord hunted and pecked: "Wesley Vogel" wrote: If there was a reply in there, I couldn't decipher it. -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User I got rid of the old error message. Now I have a new one, NTVDM KERNAL missing 16 bit system module. What I did was download the autoexec.nt,command.nt and config.nt. and unzipped them and extracted them to windows folder. Seems like the only file copied was auto.exe. Tell me what do to. I want to be able to run my programs. Chord expand CD-ROM Drive Letter:\i386\config.nt_ c:\windows\system32\config.nt expand CD-ROM Drive Letter:\i386\autoexec.nt_ c:\windows\system32\autoexec.nt expand CD-ROM Drive Letter:\i386\command.co_ c:\windows\system32\command.com exit 5. Start or install the program. If the issue is resolved, do not complete the remaining steps. If the issue is not resolved, go to the next step. 6. Note: The Command.com file is not edited or created in this in the following process. Because of this, you may have to expand it from your Windows XP CD-ROM. Start Notepad. 7. In Notepad, type the following entries: dos=high, umb device=%SYSTEMROOT%\system32\himem.sys files=40 8. On the File menu, click Save As. 9. In the File Name box, type Config.nt, and then click Save. Close the Config.nt file. 10. On the File menu, click New. 11. In the new blank document, type the following entries: @echo off lh %SYSTEMROOT%\system32\mscdexnt.exe lh %SYSTEMROOT%\system32\redir lh %SYSTEMROOT%\system32\dosx SET BLASTER=A220 I5 D1 P330 T3 12. On the File menu, click Save As. 13. In the File Name box, type Autoexec.nt, and then click Save. Close the Autoexec.nt file. 14. Start Windows Explorer. Locate the Config.nt file, right-click the Config.nt file, and then click Copy. 15. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 16. Locate the Autoexec.nt file, right-click the Autoexec.nt file, and then click Copy. 17. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 18. Locate the Command.com file, right-click the expanded Command.com file, and then click Copy. 19. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. Restart your computer. If the issue continues to occur, copy the Autoexec.nt and Config.nt files from the Repair folder in Windows to the System folder. To do so, follow these steps: 1. Click Start, click Run, type c:\windows\repair, and then click OK. 2. Right-click autoexec.nt, and then click Copy. 3. Click Start, click Run, type c:\windows\system32, and then click OK. 4. Right-click anywhere in that folder, and then click Paste. 5. Right-click the Autoexect.nt file that you just copied, and then click Properties. 6. Click to select Read-Only, and then click OK. 7. Repeat steps 1 through 6 to copy the Config.nt file. Note You must enable Read-Only permissions or the files will be removed after you restart Windows. MORE INFORMATION For more information about MS-DOS-based programs in Windows, click the following article numbers to view the articles in the Microsoft Knowledge Base: 305521 (http://support.microsoft.com/kb/305521/) "16-bit MS-DOS Subsystem" error message when you run an MS-DOS or 16-Bit Windows program in Windows Server 2003 or Windows 2000 Server 314106 (http://support.microsoft.com/kb/314106/) Troubleshooting MS-DOS-based programs in Windows XP ---------------------------------------------------------------------- -- -- ------ APPLIES TO • Microsoft Windows XP Professional • Microsoft Windows XP Home Edition Back to the top From Chord Error message when you install or start an MS-DOS or 16-bit Windows-based program http://support.microsoft.com/?id=324767 Also can be caused by a Trojan installing a file windupdater.exe and creating registry entries for that file. http://groups.google.com/groups?selm...g. google.com Wes MS-MVP Windows Shell/User In , chord hunted and pecked: "Wesley Vogel" wrote: If there was a reply in there, I couldn't decipher it. -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User I got rid of the old error message. Now I have a new one, NTVDM KERNAL missing 16 bit system module. What I did was download the autoexec.nt,command.nt and config.nt. and unzipped them and extracted them to windows folder. Seems like the only file copied was auto.exe. Tell me what do to. I want to be able to run my programs. Chord expand CD-ROM Drive Letter:\i386\config.nt_ c:\windows\system32\config.nt expand CD-ROM Drive Letter:\i386\autoexec.nt_ c:\windows\system32\autoexec.nt expand CD-ROM Drive Letter:\i386\command.co_ c:\windows\system32\command.com exit 5. Start or install the program. If the issue is resolved, do not complete the remaining steps. If the issue is not resolved, go to the next step. 6. Note: The Command.com file is not edited or created in this in the following process. Because of this, you may have to expand it from your Windows XP CD-ROM. Start Notepad. 7. In Notepad, type the following entries: dos=high, umb device=%SYSTEMROOT%\system32\himem.sys files=40 8. On the File menu, click Save As. 9. In the File Name box, type Config.nt, and then click Save. Close the Config.nt file. 10. On the File menu, click New. 11. In the new blank document, type the following entries: @echo off lh %SYSTEMROOT%\system32\mscdexnt.exe lh %SYSTEMROOT%\system32\redir lh %SYSTEMROOT%\system32\dosx SET BLASTER=A220 I5 D1 P330 T3 12. On the File menu, click Save As. 13. In the File Name box, type Autoexec.nt, and then click Save. Close the Autoexec.nt file. 14. Start Windows Explorer. Locate the Config.nt file, right-click the Config.nt file, and then click Copy. 15. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 16. Locate the Autoexec.nt file, right-click the Autoexec.nt file, and then click Copy. 17. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 18. Locate the Command.com file, right-click the expanded Command.com file, and then click Copy. 19. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. Restart your computer. If the issue continues to occur, copy the Autoexec.nt and Config.nt files from the Repair folder in Windows to the System folder. To do so, follow these steps: 1. Click Start, click Run, type c:\windows\repair, and then click OK. 2. Right-click autoexec.nt, and then click Copy. 3. Click Start, click Run, type c:\windows\system32, and then click OK. 4. Right-click anywhere in that folder, and then click Paste. 5. Right-click the Autoexect.nt file that you just copied, and then click Properties. 6. Click to select Read-Only, and then click OK. 7. Repeat steps 1 through 6 to copy the Config.nt file. Note You must enable Read-Only permissions or the files will be removed after you restart Windows. MORE INFORMATION For more information about MS-DOS-based programs in Windows, click the following article numbers to view the articles in the Microsoft Knowledge Base: 305521 (http://support.microsoft.com/kb/305521/) "16-bit MS-DOS Subsystem" error message when you run an MS-DOS or 16-Bit Windows program in Windows Server 2003 or Windows 2000 Server 314106 (http://support.microsoft.com/kb/314106/) Troubleshooting MS-DOS-based programs in Windows XP ---------------------------------------------------------------------- -- -- ------ APPLIES TO • Microsoft Windows XP Professional • Microsoft Windows XP Home Edition Back to the top From Chord Error message when you install or start an MS-DOS or 16-bit Windows-based program http://support.microsoft.com/?id=324767 Also can be caused by a Trojan installing a file windupdater.exe and creating registry entries for that file. http://groups.google.com/groups?selm...g. google.com |
#9
|
|||
|
|||
16 bit Windows Subsystem
chord" wrote: "To Wesley Vogel" Never received a reply from anybody. From Chord The first thing that you want to do is get rid of any malware that you might have on your machine. Update your antivirus software and run a full system scan. "I did this. No virus" Chord Update whatever anti-spyware applications that you have and run a full system scan with each one. NTVDM KERNEL: missing 16-bit system module please re-install the following module to your system32 directory: name of missing file What is the name of the missing file or module in the NTVDM KERNEL error message? NTVDM is NTVDM.exe it is the NT Virtual DOS Machine. NTVDM.exe runs old 16-bit applications. What is the name of the program that you are trying to run from your CD? Is it an old MS-DOS program? " BAND IN THE BOX 2001" Chord None of these 16-bit error messages should be popping up if you are trying to run a modern program. You should run the System File Checker (sfc.exe) it replaces screwed up system files. "I ran This" Chord Load your XP CD in your CD drive." " I did this" Start | Run | Type or paste: sfc /scannow | Click OK If you have XP Home and it asks for your XP Pro CD, see this KB article... You may be prompted to insert a Windows XP Professional CD when you run the System File Checker tool in Windows XP Home Edition http://support.microsoft.com/default...b;en-us;897128 "Wes, I was prompted to insert Windows XP Professional CD. The message was Files that are required to run properly must be copied to the dll cache. Insert you windows xp professional cd-rom -now. I keep hitting retry when this message comes up. Seems i'm going around in circles. Nothing is being done." Chord If SFC.EXE did anything it will be in the Event Viewer. Open the Event Viewer... Start | Run | Type: eventvwr | Click OK | Click System | Look at any Windows File Protection entries. " I did this. Just said Windows file protection started" Chord Explains a whole bunch about sfc.exe. scannow sfc (sfc.exe) http://www.updatexp.com/scannow-sfc.html "Wes, I made a copy of Fp40ext.inf and Ims.inf in the service pak 386 folder. Still getting errormessage please reinstall following module to your systemn 32 directory COMM.DRIVE What do I do next? anybody can help me?" Chord -- To Wesley Vogel" From Chord The first thing that you want to do is get rid of any malware that you might have on your machine. Update your antivirus software and run a full system scan. "I did this. No virus" Chord Update whatever anti-spyware applications that you have and run a full system scan with each one. NTVDM KERNEL: missing 16-bit system module please re-install the following module to your system32 directory: name of missing file What is the name of the missing file or module in the NTVDM KERNEL error message? NTVDM is NTVDM.exe it is the NT Virtual DOS Machine. NTVDM.exe runs old 16-bit applications. What is the name of the program that you are trying to run from your CD? Is it an old MS-DOS program? " BAND IN THE BOX 2001" Chord None of these 16-bit error messages should be popping up if you are trying to run a modern program. You should run the System File Checker (sfc.exe) it replaces screwed up system files. "I ran This" Chord Load your XP CD in your CD drive." " I did this" Start | Run | Type or paste: sfc /scannow | Click OK If you have XP Home and it asks for your XP Pro CD, see this KB article... You may be prompted to insert a Windows XP Professional CD when you run the System File Checker tool in Windows XP Home Edition http://support.microsoft.com/default...b;en-us;897128 "Wes, I was prompted to insert Windows XP Professional CD. The message was Files that are required to run properly must be copied to the dll cache. Insert you windows xp professional cd-rom -now. I keep hitting retry when this message comes up. Seems i'm going around in circles. Nothing is being done." Chord If SFC.EXE did anything it will be in the Event Viewer. Open the Event Viewer... Start | Run | Type: eventvwr | Click OK | Click System | Look at any Windows File Protection entries. " I did this. Just said Windows file protection started" Chord Explains a whole bunch about sfc.exe. scannow sfc (sfc.exe) http://www.updatexp.com/scannow-sfc.html "Wes, I made a copy of Fp40ext.inf and Ims.inf in the service pak 386 folder. Still getting errormessage please reinstall following module to your systemn 32 directory COMM.DRIVE What do I do next? anybody can help me?" Chord -- Wes MS-MVP Windows Shell/User In , chord hunted and pecked: "Wesley Vogel" wrote: If there was a reply in there, I couldn't decipher it. -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User I got rid of the old error message. Now I have a new one, NTVDM KERNAL missing 16 bit system module. What I did was download the autoexec.nt,command.nt and config.nt. and unzipped them and extracted them to windows folder. Seems like the only file copied was auto.exe. Tell me what do to. I want to be able to run my programs. Chord expand CD-ROM Drive Letter:\i386\config.nt_ c:\windows\system32\config.nt expand CD-ROM Drive Letter:\i386\autoexec.nt_ c:\windows\system32\autoexec.nt expand CD-ROM Drive Letter:\i386\command.co_ c:\windows\system32\command.com exit 5. Start or install the program. If the issue is resolved, do not complete the remaining steps. If the issue is not resolved, go to the next step. 6. Note: The Command.com file is not edited or created in this in the following process. Because of this, you may have to expand it from your Windows XP CD-ROM. Start Notepad. 7. In Notepad, type the following entries: dos=high, umb device=%SYSTEMROOT%\system32\himem.sys files=40 8. On the File menu, click Save As. 9. In the File Name box, type Config.nt, and then click Save. Close the Config.nt file. 10. On the File menu, click New. 11. In the new blank document, type the following entries: @echo off lh %SYSTEMROOT%\system32\mscdexnt.exe lh %SYSTEMROOT%\system32\redir lh %SYSTEMROOT%\system32\dosx SET BLASTER=A220 I5 D1 P330 T3 12. On the File menu, click Save As. 13. In the File Name box, type Autoexec.nt, and then click Save. Close the Autoexec.nt file. 14. Start Windows Explorer. Locate the Config.nt file, right-click the Config.nt file, and then click Copy. 15. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 16. Locate the Autoexec.nt file, right-click the Autoexec.nt file, and then click Copy. 17. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 18. Locate the Command.com file, right-click the expanded Command.com file, and then click Copy. 19. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. Restart your computer. If the issue continues to occur, copy the Autoexec.nt and Config.nt files from the Repair folder in Windows to the System folder. To do so, follow these steps: 1. Click Start, click Run, type c:\windows\repair, and then click OK. 2. Right-click autoexec.nt, and then click Copy. 3. Click Start, click Run, type c:\windows\system32, and then click OK. 4. Right-click anywhere in that folder, and then click Paste. 5. Right-click the Autoexect.nt file that you just copied, and then click Properties. 6. Click to select Read-Only, and then click OK. 7. Repeat steps 1 through 6 to copy the Config.nt file. Note You must enable Read-Only permissions or the files will be removed after you restart Windows. MORE INFORMATION For more information about MS-DOS-based programs in Windows, click the following article numbers to view the articles in the Microsoft Knowledge Base: 305521 (http://support.microsoft.com/kb/305521/) "16-bit MS-DOS Subsystem" error message when you run an MS-DOS or 16-Bit Windows program in Windows Server 2003 or Windows 2000 Server 314106 (http://support.microsoft.com/kb/314106/) Troubleshooting MS-DOS-based programs in Windows XP ---------------------------------------------------------------------- -- -- ------ APPLIES TO • Microsoft Windows XP Professional • Microsoft Windows XP Home Edition Back to the top From Chord Error message when you install or start an MS-DOS or 16-bit Windows-based program http://support.microsoft.com/?id=324767 Also can be caused by a Trojan installing a file windupdater.exe and creating registry entries for that file. http://groups.google.com/groups?selm...g. google.com Wes MS-MVP Windows Shell/User In , chord hunted and pecked: "Wesley Vogel" wrote: If there was a reply in there, I couldn't decipher it. -- Hope this helps. Let us know. Wes MS-MVP Windows Shell/User I got rid of the old error message. Now I have a new one, NTVDM KERNAL missing 16 bit system module. What I did was download the autoexec.nt,command.nt and config.nt. and unzipped them and extracted them to windows folder. Seems like the only file copied was auto.exe. Tell me what do to. I want to be able to run my programs. Chord expand CD-ROM Drive Letter:\i386\config.nt_ c:\windows\system32\config.nt expand CD-ROM Drive Letter:\i386\autoexec.nt_ c:\windows\system32\autoexec.nt expand CD-ROM Drive Letter:\i386\command.co_ c:\windows\system32\command.com exit 5. Start or install the program. If the issue is resolved, do not complete the remaining steps. If the issue is not resolved, go to the next step. 6. Note: The Command.com file is not edited or created in this in the following process. Because of this, you may have to expand it from your Windows XP CD-ROM. Start Notepad. 7. In Notepad, type the following entries: dos=high, umb device=%SYSTEMROOT%\system32\himem.sys files=40 8. On the File menu, click Save As. 9. In the File Name box, type Config.nt, and then click Save. Close the Config.nt file. 10. On the File menu, click New. 11. In the new blank document, type the following entries: @echo off lh %SYSTEMROOT%\system32\mscdexnt.exe lh %SYSTEMROOT%\system32\redir lh %SYSTEMROOT%\system32\dosx SET BLASTER=A220 I5 D1 P330 T3 12. On the File menu, click Save As. 13. In the File Name box, type Autoexec.nt, and then click Save. Close the Autoexec.nt file. 14. Start Windows Explorer. Locate the Config.nt file, right-click the Config.nt file, and then click Copy. 15. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 16. Locate the Autoexec.nt file, right-click the Autoexec.nt file, and then click Copy. 17. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. 18. Locate the Command.com file, right-click the expanded Command.com file, and then click Copy. 19. Right-click the %SYSTEMROOT%\System32 folder, and then click Paste. Restart your computer. If the issue continues to occur, copy the Autoexec.nt and Config.nt files from the Repair folder in Windows to the System folder. To do so, follow these steps: 1. Click Start, click Run, type c:\windows\repair, and then click OK. 2. Right-click autoexec.nt, and then click Copy. 3. Click Start, click Run, type c:\windows\system32, and then click OK. 4. Right-click anywhere in that folder, and then click Paste. 5. Right-click the Autoexect.nt file that you just copied, and then click Properties. 6. Click to select Read-Only, and then click OK. 7. Repeat steps 1 through 6 to copy the Config.nt file. Note You must enable Read-Only permissions or the files will be removed after you restart Windows. MORE INFORMATION For more information about MS-DOS-based programs in Windows, click the following article numbers to view the articles in the Microsoft Knowledge Base: 305521 (http://support.microsoft.com/kb/305521/) "16-bit MS-DOS Subsystem" error message when you run an MS-DOS or 16-Bit Windows program in Windows Server 2003 or Windows 2000 Server 314106 (http://support.microsoft.com/kb/314106/) Troubleshooting MS-DOS-based programs in Windows XP ---------------------------------------------------------------------- -- -- ------ APPLIES TO • Microsoft Windows XP Professional • Microsoft Windows XP Home Edition Back to the top From Chord Error message when you install or start an MS-DOS or 16-bit Windows-based program http://support.microsoft.com/?id=324767 Also can be caused by a Trojan installing a file windupdater.exe and creating registry entries for that file. http://groups.google.com/groups?selm...g. google.com Was this post helpful to you? |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Uninstall hotfixes and security updates to re-install XP SP2? | Mike | General XP issues or comments | 2 | November 2nd 05 05:38 PM |
Dual Boot Question | Ken Roberts | General XP issues or comments | 21 | July 26th 05 05:59 PM |
DVD's will not play correctly. | PCCRomeo | Windows XP and video cards, drivers and similar | 2 | July 19th 05 02:04 PM |
many in one (questions) | Noname | Windows XP Help and Support | 3 | October 4th 04 04:08 AM |
Recent MSFT KBs on XP SP2 Incompatibility and Others | Joshua Heslinga | Windows Service Pack 2 | 2 | August 14th 04 10:03 PM |