If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Rate Thread | Display Modes |
#1
|
|||
|
|||
Converting From 1 TB to 2 TB via Macrium Reflect Re-Image: Partitions?
I want to replace a 1 TB drive that's on it's last legs with a 2-TB drive.
I imaged the sick drive with Macrium Reflect, creating a single file. Here's what the drive looked like in Disk Manager: https://photos.app.goo.gl/rEFsF2H9F7mNJXjRA When I just restore the image to the 2 TB file, I get a system that works, but the additional space is unavailable for expansion of the "Data" partition because "HP_RECOVERY" sits in the middle - between existing "Data" and the new unused space. I've tried to fool Mother Nature a number of ways - but with no success. It seems like that HP_RECOVERY is both essential to the day-to-day operation of the system ("Recovery" ????) AND is required to be the third partition because I've tried to force the issue by allocating a beeeeg "Data" and then restoring HP_RECOVERY at the end - but to no avail. Is this a fool's errand? My agenda is to make that extra TB available as part of the "Data" partition so I have almost 1.5 TB available for "Data". -- Pete Cresswell |
Ads |
#2
|
|||
|
|||
Converting From 1 TB to 2 TB via Macrium Reflect Re-Image: Partitions?
PeteCresswell wrote:
I want to replace a 1 TB drive that's on it's last legs with a 2-TB drive. I imaged the sick drive with Macrium Reflect, creating a single file. When I just restore the image to the 2 TB file, I get a system that works, but the additional space is unavailable for expansion of the "Data" partition because "HP_RECOVERY" sits in the middle - between existing "Data" and the new unused space. I've tried to fool Mother Nature a number of ways - but with no success. That means you may get suggestions that duplicate your unidentified "number of ways". My agenda is to make that extra TB available as part of the "Data" partition so I have almost 1.5 TB available for "Data". When you restored using Macrium, you could've enlarged the target or destination partition. When presented with the target partition, you could've resized it. Cannot resize smaller than the restore image but can enlarge (image gets restored and partition gets enlarged). Since you didn't do it at that time, you can enlarge the partition using a variety of free partitioning tools, like: Easeus Partition Master https://www.easeus.com/partition-manager/epm-free.html Aomei Partition Assistant Standard https://www.aomeitech.com/pa/standard.html (looks like a clone of Easeus' product) Minitool Partition Wizard https://www.minitool.com/partition-m...zard-home.html Paragon Partition Manager Free https://www.paragon-software.com/free/pm-express/ Active@ Partition Manager http://www.lsoft.net/partman.aspx and good old Gparted (as a bootable CD or USB drive) https://gparted.org/download.php |
#3
|
|||
|
|||
Converting From 1 TB to 2 TB via Macrium Reflect Re-Image: Partitions?
(PeteCresswell) wrote:
I want to replace a 1 TB drive that's on it's last legs with a 2-TB drive. I imaged the sick drive with Macrium Reflect, creating a single file. Here's what the drive looked like in Disk Manager: https://photos.app.goo.gl/rEFsF2H9F7mNJXjRA When I just restore the image to the 2 TB file, I get a system that works, but the additional space is unavailable for expansion of the "Data" partition because "HP_RECOVERY" sits in the middle - between existing "Data" and the new unused space. I've tried to fool Mother Nature a number of ways - but with no success. It seems like that HP_RECOVERY is both essential to the day-to-day operation of the system ("Recovery" ????) AND is required to be the third partition because I've tried to force the issue by allocating a beeeeg "Data" and then restoring HP_RECOVERY at the end - but to no avail. Is this a fool's errand? My agenda is to make that extra TB available as part of the "Data" partition so I have almost 1.5 TB available for "Data". I had an answer all written up, but had to start over again. Thought of an easier way. ******* Original setup: P1 P2 P4 P3 +-----+-----------------+-------------+---------------+---------------+ | MBR | System Reserved | OS C: | DATA | HP Recovery | +-----+-----------------+-------------+---------------+---------------+ You will need to use the Macrium Restore function *3* times. 1) Restore the first two partitions. P1 P2 +-----+-----------------+-------------+ | MBR | System Reserved | OS C: | +-----+-----------------+-------------+ 2) Restore the HP Recovery partition, by dragging and dropping it onto the end of the new drive. P1 P2 P3 +-----+-----------------+-------------+---------------+ | MBR | System Reserved | OS C: | HP Recovery | +-----+-----------------+-------------+---------------+ 3) Restore the DATA partition. Drag and drop DATA onto the end of the target drive. Hit the NEXT button. Hit the BACK button. Right-click the DATA partition to get the "resize/align" menu. Resize the partition to fill the disk. P1 P2 P3 P4 +-----+-----------------+-------------+---------------+--------------------+ | MBR | System Reserved | OS C: | HP Recovery | DATA | +-----+-----------------+-------------+---------------+--------------------+ No other tools needed. You can use "diskpart" to select disk 0, list partitions, and see which partition is in which partition slot. I think the third partition in your source drive, is in the fourth slot of the partition table. And I'm hoping that no harm will be done when putting the partitions back. You see, not only are you cloning the disk, you're also putting the partitions back in "partition table order". Any software using partition numbers should remain happy, as a result of the original mistake. HTH, Paul |
#4
|
|||
|
|||
Converting From 1 TB to 2 TB via Macrium Reflect Re-Image: Partitions?
Paul wrote:
PeteCresswell wrote: I want to replace a 1 TB drive that's on it's last legs with a 2-TB drive. I imaged the sick drive with Macrium Reflect, creating a single file. Here's what the drive looked like in Disk Manager: https://photos.app.goo.gl/rEFsF2H9F7mNJXjRA When I just restore the image to the 2 TB file, I get a system that works, but the additional space is unavailable for expansion of the "Data" partition because "HP_RECOVERY" sits in the middle - between existing "Data" and the new unused space. Original setup: P1 P2 P4 P3 +-----+-----------------+-------------+---------------+---------------+ | MBR | System Reserved | OS C: | DATA | HP Recovery | +-----+-----------------+-------------+---------------+---------------+ You will need to use the Macrium Restore function *3* times. 1) Restore the first two partitions. P1 P2 +-----+-----------------+-------------+ | MBR | System Reserved | OS C: | +-----+-----------------+-------------+ 2) Restore the HP Recovery partition, by dragging and dropping it onto the end of the new drive. P1 P2 P3 +-----+-----------------+-------------+---------------+ | MBR | System Reserved | OS C: | HP Recovery | +-----+-----------------+-------------+---------------+ 3) Restore the DATA partition. Drag and drop DATA onto the end of the target drive. Hit the NEXT button. Hit the BACK button. Right-click the DATA partition to get the "resize/align" menu. Resize the partition to fill the disk. P1 P2 P3 P4 +-----+-----------------+-------------+---------------+--------------------+ | MBR | System Reserved | OS C: | HP Recovery | DATA | +-----+-----------------+-------------+---------------+--------------------+ No other tools needed. You can use "diskpart" to select disk 0, list partitions, and see which partition is in which partition slot. I think the third partition in your source drive, is in the fourth slot of the partition table. And I'm hoping that no harm will be done when putting the partitions back. You see, not only are you cloning the disk, you're also putting the partitions back in "partition table order". Any software using partition numbers should remain happy, as a result of the original mistake. HTH, Paul Not sure why he has to do any restores. Just use one of the partition managers to move and resize the partitions. The recovery partition is in the middle of the new 2 TB drive (which would've been the end of the old 1 TB drive). After the recovery partition on the new 2 TB drive is unallocated space. .-.------------------.----------.--------------------. |*| C: (Windows) | recovery | unallocated | '-'------------------'----------'--------------------' ^ |__ MBR/UEFI Use a partition manager to: - Drag the recovery partition to the end of the unallocated space on the new 2 TB drive. Now there will be unallocated space between the first partition (Windows) and the recovery partition moved to the end. .--- move to end --- .-.------------------.----'-----.--------------------. |*| C: (Windows) | recovery | unallocated | '-'------------------'----------'--------------------' becomes .-.------------------.--------------------.----------. |*| C: (Windows) | unallocated | recovery | '-'------------------'--------------------'----------' - Then resize the 1st partition so it consumes the unallocated space. .-.------------------.--------------------.----------. |*| C: (Windows) X-- enlarge C: -- | recovery | '-'------------------'--------------------'----------' becomes .-.---------------------------------------.----------. |*| C: (Windows) | recovery | '-'---------------------------------------'----------' Just do a partition move (recovery) and then enlarge a partition (C. Moving and resizing of partitions is usually faster than doing restores. I was surprised that Macrium Reflect did not include a partitioning manager. However, there are LOTS of choices and for free. |
#5
|
|||
|
|||
Converting From 1 TB to 2 TB via Macrium Reflect Re-Image: Partitions?
In message , VanguardLH
writes: [] I was surprised that Macrium Reflect did not include a partitioning manager. However, there are LOTS of choices and for free. It does allow a _resize_ during restore (up or down, IIRR), though I prefer to do that afterwards with a PM. (I use the EaseUS one, since it works for me.) -- J. P. Gilliver. UMRA: 1960/1985 MB++G()AL-IS-Ch++(p)Ar@T+H+Sh0!:`)DNAf A clean, neat and orderly desk is a sign of a sick mind. (G6JPG's mind is clearly extremely healthy ...) |
#6
|
|||
|
|||
Converting From 1 TB to 2 TB via Macrium Reflect Re-Image: Partitions?
J. P. Gilliver (John) wrote:
VanguardLH did not "writes" but wrote: I was surprised that Macrium Reflect did not include a partitioning manager. However, there are LOTS of choices and for free. It does allow a _resize_ during restore (up or down, IIRR), though I prefer to do that afterwards with a PM. (I use the EaseUS one, since it works for me.) I mentioned that in my first reply. I remember deciding where to restore, enlarging the partition, and probably other partitioning tasks. However, Reflect does not have a partition manager built into it to allow using it to do all partitioning tasks. If you change the drives often (add, delete, change partitioning, step on the MBR/UEFI bootstrap code with a standard one, and other more advanced tasks), you really need to use a partition manager. Most require you to install. Minitool lets you run it from a bootable device as does GParted. |
#7
|
|||
|
|||
Converting From 1 TB to 2 TB via Macrium Reflect Re-Image: Partitions?
"(PeteCresswell)" wrote
| When I just restore the image to the 2 TB file, I get a system that works, | but the additional space is unavailable for expansion of the "Data" partition | because "HP_RECOVERY" sits in the middle - between existing "Data" and the | new unused space. | If it were me I'd clean out all the muck. Assuming Paul's diagram is correct (I can't see your picture without alowing Google to run script).... Do a restore and clean that up. Install your software. Get rid of System Reserved by putting the boot files on C. Make a disk image of that, so you have a fresh copy. Then get rid of the HP partition. So you just have C and data partitions. It's more work now but easier and more efficient for the future. I don't know why you think the HP partition is critical. I always delete those. It's only useful if you don't have backed up disk images of C. |
#8
|
|||
|
|||
Converting From 1 TB to 2 TB via Macrium Reflect Re-Image:Partitions?
Mayayana wrote:
"(PeteCresswell)" wrote | When I just restore the image to the 2 TB file, I get a system that works, | but the additional space is unavailable for expansion of the "Data" partition | because "HP_RECOVERY" sits in the middle - between existing "Data" and the | new unused space. | If it were me I'd clean out all the muck. Assuming Paul's diagram is correct (I can't see your picture without alowing Google to run script).... Do a restore and clean that up. Install your software. Get rid of System Reserved by putting the boot files on C. Make a disk image of that, so you have a fresh copy. Then get rid of the HP partition. So you just have C and data partitions. It's more work now but easier and more efficient for the future. I don't know why you think the HP partition is critical. I always delete those. It's only useful if you don't have backed up disk images of C. It's the only way to get back to "ex factory" state. OK, so not many people want that (including myself), but some do; to give to a friend, pass on to a charity, fill their system with loads of junk and then want a way back. Ed |
#9
|
|||
|
|||
Converting From 1 TB to 2 TB via Macrium Reflect Re-Image: Partitions?
Per Mayayana:
I don't know why you think the HP partition is critical. I always delete those. It's only useful if you don't have backed up disk images of C. That was my knee-jerk reaction: just delete it. But when I do that, the system boots up throwing a dialog that reads something like "Desktop.ini not found" and there's basically an empty desktop - so I jumped to the assumption that the HP partition contained some files used day-to-day. Vanguard, Paul, John, and you have given me hope. I had thrown in the towel and just re-imaged to an old 1TB backup drive - but now I think I will re-visit the scene with the 2TB drive. First thing I will try is looking for Macrium's Resize-Partition option. If that doesn't happen, I'll move on to Paul's approach and, if that does not work out, will start looking for a partition manager that will do the job. Seems pretty obvious that something else is going on that I am unaware of vis-a-vis my incorrect assumption that the HP_RECOVERY partition was playing an essential role. The situation acts like there is a file (boot block?) somewhere that points to Partition 0, Partition 1, Partition 2, and so-forth - and, when partitions are moved around without changing that file, Bad Things happen. -- Pete Cresswell |
#10
|
|||
|
|||
Converting From 1 TB to 2 TB via Macrium Reflect Re-Image: Partitions?
On Tue, 19 Jun 2018 10:54:04 -0400, "(PeteCresswell)"
wrote: Per Mayayana: I don't know why you think the HP partition is critical. I always delete those. It's only useful if you don't have backed up disk images of C. That was my knee-jerk reaction: just delete it. But when I do that, the system boots up throwing a dialog that reads something like "Desktop.ini not found" and there's basically an empty desktop - so I jumped to the assumption that the HP partition contained some files used day-to-day. Vanguard, Paul, John, and you have given me hope. I had thrown in the towel and just re-imaged to an old 1TB backup drive - but now I think I will re-visit the scene with the 2TB drive. First thing I will try is looking for Macrium's Resize-Partition option. If that doesn't happen, I'll move on to Paul's approach and, if that does not work out, will start looking for a partition manager that will do the job. I would recommend using VanguardLH's approach first. Grab a partition manager and be amazed at how easy it is to do what you're trying to do. My choice is the Minitool Partition Wizard, which he linked, but the others should work as well. No need to do another Macrium restore, and (sorry Paul!) no need to do multiple restores. A partition manager will have you sorted within a few minutes. -- Char Jackson |
#11
|
|||
|
|||
Converting From 1 TB to 2 TB via Macrium Reflect Re-Image: Partitions?
"(PeteCresswell)" wrote
| That was my knee-jerk reaction: just delete it. | | But when I do that, the system boots up throwing a dialog that reads | something like "Desktop.ini not found" and there's basically an empty desktop | - so I jumped to the assumption that the HP partition contained some files | used day-to-day. | I've never seen that. But I've also never done it without first fixing the boot. Put the boot files on C so you can rid of the system partition. Then alo make sure the boot config is OK. (BCDEdit from terabyte unlimited can do that. It's part of BootIt. Probably Macrium also has a tool. So then you just have a normal, bootable C rive and you can dump everything else. |
#12
|
|||
|
|||
Converting From 1 TB to 2 TB via Macrium Reflect Re-Image: Partitions?
On Mon, 18 Jun 2018 21:04:10 -0400, Paul wrote:
I had an answer all written up, but had to start over again. Thought of an easier way. You will need to use the Macrium Restore function *3* times. LOL No, a partition manager sorts it right out. A second restore is completely unnecessary, let alone a third. If this was your "easier way", I wonder what the first approach could have been. ;-) I commend your thoroughness, but sometimes the solution is right in plain sight. -- Char Jackson |
#13
|
|||
|
|||
Converting From 1 TB to 2 TB via Macrium Reflect Re-Image: Partitions?
"Ed Cryer" wrote
| | It's the only way to get back to "ex factory" state. I understand that. But that can also be done by making a disk image. I would then clean it up and install software, before imaging, but if people like an HP logo on their desktop then that's fine, too. A disk image is also safer and simpler. If you leave the restore partition and the separate system boot partition then if the hard disk dies you've lost everything. And if you want to put in a new hard disk you're stuck with Pete's problem: A convoluted system of unnecessary, interdependent partitions that have to all be copied as-is. With disk images there's no risk if the disk dies and there can be as much backup of the images as desired. |
#14
|
|||
|
|||
Converting From 1 TB to 2 TB via Macrium Reflect Re-Image: Partitions?
Ed Cryer wrote:
Mayayana wrote: "(PeteCresswell)" wrote | When I just restore the image to the 2 TB file, I get a system that works, | but the additional space is unavailable for expansion of the "Data" partition | because "HP_RECOVERY" sits in the middle - between existing "Data" and the | new unused space. | If it were me I'd clean out all the muck. Assuming Paul's diagram is correct (I can't see your picture without alowing Google to run script).... Do a restore and clean that up. Install your software. Get rid of System Reserved by putting the boot files on C. Make a disk image of that, so you have a fresh copy. Then get rid of the HP partition. So you just have C and data partitions. It's more work now but easier and more efficient for the future. I don't know why you think the HP partition is critical. I always delete those. It's only useful if you don't have backed up disk images of C. It's the only way to get back to "ex factory" state. OK, so not many people want that (including myself), but some do; to give to a friend, pass on to a charity, fill their system with loads of junk and then want a way back. For this purpose I've made a (Macrium Reflect FREE) full image backup of all partitions, *except* C: (etc.). Such a backup is rather small - in my case 17.4GB (just a bit bigger than just the 'RECOVERY' [1] partition (17.26GB)) - so keeping it 'forever' in case it's needed, is mostly a non-issue. [1] Also an HP system (HP Pavilion 15-p142nd laptop) with Windows 8.1, but the partition is named 'RECOVERY', instead of 'HP_RECOVERY'. Probably a (HP) 8.1 versus 7 difference. |
#15
|
|||
|
|||
Converting From 1 TB to 2 TB via Macrium Reflect Re-Image:Partitions?
Mayayana wrote:
"Ed Cryer" wrote | | It's the only way to get back to "ex factory" state. I understand that. But that can also be done by making a disk image. I would then clean it up and install software, before imaging, but if people like an HP logo on their desktop then that's fine, too. A disk image is also safer and simpler. If you leave the restore partition and the separate system boot partition then if the hard disk dies you've lost everything. And if you want to put in a new hard disk you're stuck with Pete's problem: A convoluted system of unnecessary, interdependent partitions that have to all be copied as-is. With disk images there's no risk if the disk dies and there can be as much backup of the images as desired. I've just commissioned a new box of Win10 tricks. And I followed my usual course. Find fault with this for me - and give me nightmares. 1. Run it up, set up account, drive it for a while to see how it feels and handles. Look for any errors and warnings under Event manager; especially in the Windows System Log. 2. Remove all the crapware. I do this manually, one by one. 3. Take two backups: a) Win Sys Image, b) Macrium C image. 4. Load browser, email prog, plus tons of regulars like Foxit, Irfanview, Sequoiaview, MS Office ..... 5. Repeat 3 above, which will be repeated from now on very regularly. Notice that I retain the OEM Recovery partition. They never exceed about 17GB. I'm not quite sure (frontal-lobe-consciously, that is) just why. But I suspect my subconscious does; it's another safety layer to fall back on, and it gets added to every Macrium image I take thereafter. BTW, in case you're going to say that that's adding time to the Macrium backups, let me tell you that the latest one took 23 mins for over 100GB. Ed |
Thread Tools | |
Display Modes | Rate This Thread |
|
|