If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
redundant computer on workgroup
I have two computers on a home workgroup. The Name of the first computer was
WINDOWSXP. The "Setup a Home or Small Office Network" wizzard was used to define a workgroup named CASTAWAYS. I then changed the name of the computer to DENNIS01 via the Computer Name tab of the System Properties window leaving the Workgroup name unchanged. I then used the "Setup a Home or Small Office Network" wizzard to add the second computer to the CASTAWAYS workgroup. The name of the second computer was DENNIS02. Each computer has a wireless card and they communicate through a Netgear router operating in Infrastructure mode and thus as an Access point. I used the "This computer connects to the internet through a residential gateway or through another computer on my network" option in the wizzard. As a result of this, My Network Places in DENNIS01 shows: DENNIS01 and DENNIS02 and I am able to access the resources of DENNIS02 through DENNIS01. My Network Places in DENNIS02 shows Castaways but when I try and expand this I get a message saying "Castaways is not accessible. You might not have permission to use this resource ............ The network path was not found" How do I give DENNIS02 permission to access access DENNIS01 |
Ads |
#2
|
|||
|
|||
redundant computer on workgroup
Since the original posting I have found that DENNIS02 can successfully Ping
DENNIS01 by IP address but not by ComputerName "Dennis Jelavic" wrote in message ... I have two computers on a home workgroup. The Name of the first computer was WINDOWSXP. The "Setup a Home or Small Office Network" wizzard was used to define a workgroup named CASTAWAYS. I then changed the name of the computer to DENNIS01 via the Computer Name tab of the System Properties window leaving the Workgroup name unchanged. I then used the "Setup a Home or Small Office Network" wizzard to add the second computer to the CASTAWAYS workgroup. The name of the second computer was DENNIS02. Each computer has a wireless card and they communicate through a Netgear router operating in Infrastructure mode and thus as an Access point. I used the "This computer connects to the internet through a residential gateway or through another computer on my network" option in the wizzard. As a result of this, My Network Places in DENNIS01 shows: DENNIS01 and DENNIS02 and I am able to access the resources of DENNIS02 through DENNIS01. My Network Places in DENNIS02 shows Castaways but when I try and expand this I get a message saying "Castaways is not accessible. You might not have permission to use this resource ............ The network path was not found" How do I give DENNIS02 permission to access access DENNIS01 |
#3
|
|||
|
|||
redundant computer on workgroup
"Dennis Jelavic" wrote in
: I have two computers on a home workgroup. The Name of the first computer was WINDOWSXP. The "Setup a Home or Small Office Network" wizzard was used to define a workgroup named CASTAWAYS. I then changed the name of the computer to DENNIS01 via the Computer Name tab of the System Properties window leaving the Workgroup name unchanged. I then used the "Setup a Home or Small Office Network" wizzard to add the second computer to the CASTAWAYS workgroup. The name of the second computer was DENNIS02. Each computer has a wireless card and they communicate through a Netgear router operating in Infrastructure mode and thus as an Access point. I used the "This computer connects to the internet through a residential gateway or through another computer on my network" option in the wizzard. As a result of this, My Network Places in DENNIS01 shows: DENNIS01 and DENNIS02 and I am able to access the resources of DENNIS02 through DENNIS01. My Network Places in DENNIS02 shows Castaways but when I try and expand this I get a message saying "Castaways is not accessible. You might not have permission to use this resource ............ The network path was not found" How do I give DENNIS02 permission to access access DENNIS01 It would appear you have a permissions problem. How to solve this depends on whether you have Simple File Sharing enabled or disabled. (It is always enabled with XP Home). Start by assuring that NetBIOS-over-TCPIP is enabled on all machines. Instructions are he "You cannot access shared files and folders or browse computers in the workgroup with Windows XP" http://support.microsoft.com/kb/318030/ Assuming Simple File Sharing, all access is through the "Guest" account. The Guest account must be active. Instructions for checking that are he "How to troubleshoot home networking in Windows XP" http://support.microsoft.com/kb/308007/ Skip 2/3 the way down to the "Troubleshoot file sharing and printer sharing" section. Also possible is the following: "Error message when you try to access a Windows XP-based network computer: "You might not have permission to use this network resource"" http://support.microsoft.com/kb/913628 HTH, John |
#4
|
|||
|
|||
redundant computer on workgroup
"Dennis Jelavic" wrote in
: I have two computers on a home workgroup. The Name of the first computer was WINDOWSXP. The "Setup a Home or Small Office Network" wizzard was used to define a workgroup named CASTAWAYS. I then changed the name of the computer to DENNIS01 via the Computer Name tab of the System Properties window leaving the Workgroup name unchanged. I then used the "Setup a Home or Small Office Network" wizzard to add the second computer to the CASTAWAYS workgroup. The name of the second computer was DENNIS02. Each computer has a wireless card and they communicate through a Netgear router operating in Infrastructure mode and thus as an Access point. I used the "This computer connects to the internet through a residential gateway or through another computer on my network" option in the wizzard. As a result of this, My Network Places in DENNIS01 shows: DENNIS01 and DENNIS02 and I am able to access the resources of DENNIS02 through DENNIS01. My Network Places in DENNIS02 shows Castaways but when I try and expand this I get a message saying "Castaways is not accessible. You might not have permission to use this resource ............ The network path was not found" How do I give DENNIS02 permission to access access DENNIS01 It would appear you have a permissions problem. How to solve this depends on whether you have Simple File Sharing enabled or disabled. (It is always enabled with XP Home). Start by assuring that NetBIOS-over-TCPIP is enabled on all machines. Instructions are he "You cannot access shared files and folders or browse computers in the workgroup with Windows XP" http://support.microsoft.com/kb/318030/ Assuming Simple File Sharing, all access is through the "Guest" account. The Guest account must be active. Instructions for checking that are he "How to troubleshoot home networking in Windows XP" http://support.microsoft.com/kb/308007/ Skip 2/3 the way down to the "Troubleshoot file sharing and printer sharing" section. Also possible is the following: "Error message when you try to access a Windows XP-based network computer: "You might not have permission to use this network resource"" http://support.microsoft.com/kb/913628 HTH, John |
Thread Tools | |
Display Modes | |
|
|