If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
convert USB2.0 to USB1.1
I have a USB analyzer which can only capture Data for upto 12Mbit/
s. When I connect a device which has a USB2.0 protocol on it, the USB Analyzer is not able to catch this information. How can I force one of my computer ports to work as USB 1.1? Is there a way? Thanks in advance. |
Ads |
#2
|
|||
|
|||
convert USB2.0 to USB1.1
Tutu wrote:
I have a USB analyzer which can only capture Data for upto 12Mbit/ s. When I connect a device which has a USB2.0 protocol on it, the USB Analyzer is not able to catch this information. How can I force one of my computer ports to work as USB 1.1? Is there a way? Thanks in advance. You could try the following. Go to Device Manager. Find the USB section. One of the USB entries has the word "Enhanced" in it. Select that entry. Do "properties" on it. At the bottom of the Properties for the Enhanced entry, there is a "Device Usage" box. It has values like Use this device (enable) Do not use this device (disable) Change the setting to "disable". Then try your analyzer. That is what I'd try. It is also possible, that USB2 could be disabled in the BIOS, but not all BIOS have the same control features listed on the screen. You should notice a visible different in UVCView after you do that also. A bunch of entries should disappear near the bottom. I would close UVCView, before you start the process of changing the Device Manager. Once the change is made in Device Manager, run UVCView again, and the USB2 section should be gone. (On my ICH5 Southbridge, the USB2 entries are near the bottom of the UVCView window.) http://www.microsoft.com/whdc/device...VCViewdwn.mspx My best guess, Paul |
#3
|
|||
|
|||
convert USB2.0 to USB1.1
You could try connecting it through an external USB 1.1 hub to the PC.
"Tutu" wrote in message ... I have a USB analyzer which can only capture Data for upto 12Mbit/ s. When I connect a device which has a USB2.0 protocol on it, the USB Analyzer is not able to catch this information. How can I force one of my computer ports to work as USB 1.1? Is there a way? Thanks in advance. |
#4
|
|||
|
|||
convert USB2.0 to USB1.1
It is posible to change usb protocole from BIOS
For this porpse firt Make backup of your bios then extract bios.bin file in your working folder identify the usb bus file that contan usb codes just like Processor codes( When u update Processor Code it run fast & smoth) change the usb protocole/Code file with high speed USB 2.0 Codes file ( extractin from other pc that contan high speed usb ) repack bios.bin file then flash into the pc restart pc you are notes ur usb bus detet as high speed b/c all type of bus rate depend on BIOS that contain first startup drivers/codes. You also develp our own code for USB or other Hardware. I test on many typeof motherboard my first exparement on (intel 810 lmrt) 2nd (810 DST) then (810 Mini), (815) , etc On Sunday, December 23, 2007 3:19 PM Paul wrote: Tutu wrote: You could try the following. Go to Device Manager. Find the USB section. One of the USB entries has the word "Enhanced" in it. Select that entry. Do "properties" on it. At the bottom of the Properties for the Enhanced entry, there is a "Device Usage" box. It has values like Use this device (enable) Do not use this device (disable) Change the setting to "disable". Then try your analyzer. That is what I'd try. It is also possible, that USB2 could be disabled in the BIOS, but not all BIOS have the same control features listed on the screen. You should notice a visible different in UVCView after you do that also. A bunch of entries should disappear near the bottom. I would close UVCView, before you start the process of changing the Device Manager. Once the change is made in Device Manager, run UVCView again, and the USB2 section should be gone. (On my ICH5 Southbridge, the USB2 entries are near the bottom of the UVCView window.) http://www.microsoft.com/whdc/device...VCViewdwn.mspx My best guess, Paul On Monday, December 24, 2007 12:15 AM Tutu wrote: I have a USB analyzer which can only capture Data for upto 12Mbit/ s. When I connect a device which has a USB2.0 protocol on it, the USB Analyzer is not able to catch this information. How can I force one of my computer ports to work as USB 1.1? Is there a way? Thanks in advance. On Monday, December 24, 2007 5:41 PM RalfG wrote: You could try connecting it through an external USB 1.1 hub to the PC. |
#5
|
|||
|
|||
convert USB2.0 to USB1.1
On 3/31/2011 8:45 PM, O-Yes G wrote:
December 23, 2007 Replying to a post from 2007? What an idiot. |
#6
|
|||
|
|||
convert USB2.0 to USB1.1
In ,
Jack Toff typed: On 3/31/2011 8:45 PM, O-Yes G wrote: December 23, 2007 Replying to a post from 2007? What an idiot. Why? It's a valid query that was not answered and now is. When you look at Google ALL of the posts, including the belated correct response, will be there for those doing the research. Nearly every e-mail in the free world is stored at Google and other such repositories for perpetuity. HTH, Twayne` |
Thread Tools | |
Display Modes | |
|
|