If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Microsoft Keyboard Causes Bootup to hang
Hi
I've got a brand new PC (pre-built):- P4 3.2ghz HT 512mb ddr 400mhz RAM Asus P4P800SE Mo/Bo (Latest BIOS) 200GB S-ATA Maxtor Drive Windows XP Home I've connected a new Wireless Keyboard and mouse from Microsoft (optical wireless desktop Elite) - LATEST drivers The Wireless hub has 2 cables running from it. 1 is for the PS/2 connection to the PC, the other is USB for the mouse. When I connect the Keyboard to the PS/2 socket the system will not boot. It powers up, and the H/D light flickers away, but it will not send video signal to the Monitor, and pressing the power button again does not switch it off (I have to hold it for the 4 secs to power down.) If I hit the reset button, the whole thing fires up fine, If I connect a different Keyboard to the PS/2 it fires up fine. I've tried changing the wireless channel and this has no effect. If I disconnect the wireless K/B, power up with a different K/B, power down, reconnect the Wireless K/B, it fires up OK on the FIRST attempt ONLY. A very bizarre problem! I'm hoping someone else out there has had this problem, and solved it! Any advice on this greatly appreciated! Nik. -- ================================================== ===== Remove S P A M K I L L From my Email address to reply to me Directly ================================================== ===== |
Ads |
#2
|
|||
|
|||
Microsoft Keyboard Causes Bootup to hang
Just a suggestion. Have you tried to update BIOS for a new version
"Walmsley's" wrote in message ... Hi I've got a brand new PC (pre-built):- P4 3.2ghz HT 512mb ddr 400mhz RAM Asus P4P800SE Mo/Bo (Latest BIOS) 200GB S-ATA Maxtor Drive Windows XP Home I've connected a new Wireless Keyboard and mouse from Microsoft (optical wireless desktop Elite) - LATEST drivers The Wireless hub has 2 cables running from it. 1 is for the PS/2 connection to the PC, the other is USB for the mouse. When I connect the Keyboard to the PS/2 socket the system will not boot. It powers up, and the H/D light flickers away, but it will not send video signal to the Monitor, and pressing the power button again does not switch it off (I have to hold it for the 4 secs to power down.) If I hit the reset button, the whole thing fires up fine, If I connect a different Keyboard to the PS/2 it fires up fine. I've tried changing the wireless channel and this has no effect. If I disconnect the wireless K/B, power up with a different K/B, power down, reconnect the Wireless K/B, it fires up OK on the FIRST attempt ONLY. A very bizarre problem! I'm hoping someone else out there has had this problem, and solved it! Any advice on this greatly appreciated! Nik. -- ================================================== ===== Remove S P A M K I L L From my Email address to reply to me Directly ================================================== ===== |
#3
|
|||
|
|||
Microsoft Keyboard Causes Bootup to hang
"Walmsley's" wrote in message ... Hi I've got a brand new PC (pre-built):- P4 3.2ghz HT 512mb ddr 400mhz RAM Asus P4P800SE Mo/Bo (Latest BIOS) 200GB S-ATA Maxtor Drive Windows XP Home I've connected a new Wireless Keyboard and mouse from Microsoft (optical wireless desktop Elite) - LATEST drivers The Wireless hub has 2 cables running from it. 1 is for the PS/2 connection to the PC, the other is USB for the mouse. When I connect the Keyboard to the PS/2 socket the system will not boot. It powers up, and the H/D light flickers away, but it will not send video signal to the Monitor, and pressing the power button again does not switch it off (I have to hold it for the 4 secs to power down.) A keyboard and mouse must be detected for the system to boot. I use the Wireless MultiMedia model. Your kbd/mouse is not being properly detected. Since it does run correctly using the reset, consider leaving the power on at shutdown, and just using reset to start your system. (works fine for me running W'98) Since your board has two ps/2 ports, try using the green adapter plug that came with your unit. Some systems don't detect well using the USB. Try running both keyboard and mouse on the ps/2 ports. Go to system properties and see that the set is named properly...... if so install new driver from your OS disc. Replace the cheap batteries that came with the unit with new alkaline batteries. Go to control panel and try the "add new hardware" utility to see if you can get it to load a new keyboard driver. It's a MS unit, so I would try to load drivers from your OS disc. Failing that, try to make a new boot disc and see if you can get it to boot properly. If you can get it to boot from a boot disc, I would remove the kbd/mouse from system/device manager, and boot from the boot disc in the hope that it will detect it as new hardware and load the correct driver set. If I hit the reset button, the whole thing fires up fine, If I connect a different Keyboard to the PS/2 it fires up fine. I've tried changing the wireless channel and this has no effect. If I disconnect the wireless K/B, power up with a different K/B, power down, reconnect the Wireless K/B, it fires up OK on the FIRST attempt ONLY. |
#4
|
|||
|
|||
Microsoft Keyboard Causes Bootup to hang
As per the specs I posted "Latest BIOS"
Thanks anyway. Nik. "Kevin Haklar" wrote in message ... Just a suggestion. Have you tried to update BIOS for a new version "Walmsley's" wrote in message ... Hi I've got a brand new PC (pre-built):- P4 3.2ghz HT 512mb ddr 400mhz RAM Asus P4P800SE Mo/Bo (Latest BIOS) 200GB S-ATA Maxtor Drive Windows XP Home I've connected a new Wireless Keyboard and mouse from Microsoft (optical wireless desktop Elite) - LATEST drivers The Wireless hub has 2 cables running from it. 1 is for the PS/2 connection to the PC, the other is USB for the mouse. When I connect the Keyboard to the PS/2 socket the system will not boot. It powers up, and the H/D light flickers away, but it will not send video signal to the Monitor, and pressing the power button again does not switch it off (I have to hold it for the 4 secs to power down.) If I hit the reset button, the whole thing fires up fine, If I connect a different Keyboard to the PS/2 it fires up fine. I've tried changing the wireless channel and this has no effect. If I disconnect the wireless K/B, power up with a different K/B, power down, reconnect the Wireless K/B, it fires up OK on the FIRST attempt ONLY. A very bizarre problem! I'm hoping someone else out there has had this problem, and solved it! Any advice on this greatly appreciated! Nik. -- ================================================== ===== Remove S P A M K I L L From my Email address to reply to me Directly ================================================== ===== |
#5
|
|||
|
|||
Microsoft Keyboard Causes Bootup to hang
"Walmsley's" wrote in message
... Hi I've got a brand new PC (pre-built):- P4 3.2ghz HT 512mb ddr 400mhz RAM Asus P4P800SE Mo/Bo (Latest BIOS) 200GB S-ATA Maxtor Drive Windows XP Home I've connected a new Wireless Keyboard and mouse from Microsoft (optical wireless desktop Elite) - LATEST drivers The Wireless hub has 2 cables running from it. 1 is for the PS/2 connection to the PC, the other is USB for the mouse. When I connect the Keyboard to the PS/2 socket the system will not boot. It powers up, and the H/D light flickers away, but it will not send video signal to the Monitor, and pressing the power button again does not switch it off (I have to hold it for the 4 secs to power down.) If I hit the reset button, the whole thing fires up fine, If I connect a different Keyboard to the PS/2 it fires up fine. I've tried changing the wireless channel and this has no effect. If I disconnect the wireless K/B, power up with a different K/B, power down, reconnect the Wireless K/B, it fires up OK on the FIRST attempt ONLY. A very bizarre problem! I'm hoping someone else out there has had this problem, and solved it! Any advice on this greatly appreciated! Have a look in the BIOS and see if "Legacy USB mouse/keyboad support" (or similar) is enabled. Try it with both settings. It could also be that your USB devices are taking too much power from the USB bus - try disconnecting all USB devices other than mouse/keyboard. If that's no help, I suggest you go through the steps that "Pepperoni" suggests. HTH -- Rob |
#6
|
|||
|
|||
Microsoft Keyboard Causes Bootup to hang
A mouse is not required for the bios to complete, and access the OS
partition. "Pepperoni" wrote in message ... "Walmsley's" wrote in message ... Hi I've got a brand new PC (pre-built):- P4 3.2ghz HT 512mb ddr 400mhz RAM Asus P4P800SE Mo/Bo (Latest BIOS) 200GB S-ATA Maxtor Drive Windows XP Home I've connected a new Wireless Keyboard and mouse from Microsoft (optical wireless desktop Elite) - LATEST drivers The Wireless hub has 2 cables running from it. 1 is for the PS/2 connection to the PC, the other is USB for the mouse. When I connect the Keyboard to the PS/2 socket the system will not boot. It powers up, and the H/D light flickers away, but it will not send video signal to the Monitor, and pressing the power button again does not switch it off (I have to hold it for the 4 secs to power down.) A keyboard and mouse must be detected for the system to boot. I use the Wireless MultiMedia model. Your kbd/mouse is not being properly detected. Since it does run correctly using the reset, consider leaving the power on at shutdown, and just using reset to start your system. (works fine for me running W'98) Since your board has two ps/2 ports, try using the green adapter plug that came with your unit. Some systems don't detect well using the USB. Try running both keyboard and mouse on the ps/2 ports. Go to system properties and see that the set is named properly...... if so install new driver from your OS disc. Replace the cheap batteries that came with the unit with new alkaline batteries. Go to control panel and try the "add new hardware" utility to see if you can get it to load a new keyboard driver. It's a MS unit, so I would try to load drivers from your OS disc. Failing that, try to make a new boot disc and see if you can get it to boot properly. If you can get it to boot from a boot disc, I would remove the kbd/mouse from system/device manager, and boot from the boot disc in the hope that it will detect it as new hardware and load the correct driver set. If I hit the reset button, the whole thing fires up fine, If I connect a different Keyboard to the PS/2 it fires up fine. I've tried changing the wireless channel and this has no effect. If I disconnect the wireless K/B, power up with a different K/B, power down, reconnect the Wireless K/B, it fires up OK on the FIRST attempt ONLY. |
#7
|
|||
|
|||
Microsoft Keyboard Causes Bootup to hang
Go into the Bios and disable Fast Booting. It should be fine then
"Pepperoni" wrote in message ... "Walmsley's" wrote in message ... Hi I've got a brand new PC (pre-built):- P4 3.2ghz HT 512mb ddr 400mhz RAM Asus P4P800SE Mo/Bo (Latest BIOS) 200GB S-ATA Maxtor Drive Windows XP Home I've connected a new Wireless Keyboard and mouse from Microsoft (optical wireless desktop Elite) - LATEST drivers The Wireless hub has 2 cables running from it. 1 is for the PS/2 connection to the PC, the other is USB for the mouse. When I connect the Keyboard to the PS/2 socket the system will not boot. It powers up, and the H/D light flickers away, but it will not send video signal to the Monitor, and pressing the power button again does not switch it off (I have to hold it for the 4 secs to power down.) A keyboard and mouse must be detected for the system to boot. I use the Wireless MultiMedia model. Your kbd/mouse is not being properly detected. Since it does run correctly using the reset, consider leaving the power on at shutdown, and just using reset to start your system. (works fine for me running W'98) Since your board has two ps/2 ports, try using the green adapter plug that came with your unit. Some systems don't detect well using the USB. Try running both keyboard and mouse on the ps/2 ports. Go to system properties and see that the set is named properly...... if so install new driver from your OS disc. Replace the cheap batteries that came with the unit with new alkaline batteries. Go to control panel and try the "add new hardware" utility to see if you can get it to load a new keyboard driver. It's a MS unit, so I would try to load drivers from your OS disc. Failing that, try to make a new boot disc and see if you can get it to boot properly. If you can get it to boot from a boot disc, I would remove the kbd/mouse from system/device manager, and boot from the boot disc in the hope that it will detect it as new hardware and load the correct driver set. If I hit the reset button, the whole thing fires up fine, If I connect a different Keyboard to the PS/2 it fires up fine. I've tried changing the wireless channel and this has no effect. If I disconnect the wireless K/B, power up with a different K/B, power down, reconnect the Wireless K/B, it fires up OK on the FIRST attempt ONLY. |
#8
|
|||
|
|||
Microsoft Keyboard Causes Bootup to hang
I've tried every combination of USB devices. Bottom line is, if the Keyboard
is attached, the system hangs. I've done it with JUST the keyboard attached, it's PS2. Weird fault!! Nik. "Rob Hemmings" wrote in message ... "Walmsley's" wrote in message ... Hi I've got a brand new PC (pre-built):- P4 3.2ghz HT 512mb ddr 400mhz RAM Asus P4P800SE Mo/Bo (Latest BIOS) 200GB S-ATA Maxtor Drive Windows XP Home I've connected a new Wireless Keyboard and mouse from Microsoft (optical wireless desktop Elite) - LATEST drivers The Wireless hub has 2 cables running from it. 1 is for the PS/2 connection to the PC, the other is USB for the mouse. When I connect the Keyboard to the PS/2 socket the system will not boot. It powers up, and the H/D light flickers away, but it will not send video signal to the Monitor, and pressing the power button again does not switch it off (I have to hold it for the 4 secs to power down.) If I hit the reset button, the whole thing fires up fine, If I connect a different Keyboard to the PS/2 it fires up fine. I've tried changing the wireless channel and this has no effect. If I disconnect the wireless K/B, power up with a different K/B, power down, reconnect the Wireless K/B, it fires up OK on the FIRST attempt ONLY. A very bizarre problem! I'm hoping someone else out there has had this problem, and solved it! Any advice on this greatly appreciated! Have a look in the BIOS and see if "Legacy USB mouse/keyboad support" (or similar) is enabled. Try it with both settings. It could also be that your USB devices are taking too much power from the USB bus - try disconnecting all USB devices other than mouse/keyboard. If that's no help, I suggest you go through the steps that "Pepperoni" suggests. HTH -- Rob |
#9
|
|||
|
|||
Microsoft Keyboard Causes Bootup to hang
A mouse is not required for the bios to complete, and access the OS
partition. "Pepperoni" wrote in message ... "Walmsley's" wrote in message ... Hi I've got a brand new PC (pre-built):- P4 3.2ghz HT 512mb ddr 400mhz RAM Asus P4P800SE Mo/Bo (Latest BIOS) 200GB S-ATA Maxtor Drive Windows XP Home I've connected a new Wireless Keyboard and mouse from Microsoft (optical wireless desktop Elite) - LATEST drivers The Wireless hub has 2 cables running from it. 1 is for the PS/2 connection to the PC, the other is USB for the mouse. When I connect the Keyboard to the PS/2 socket the system will not boot. It powers up, and the H/D light flickers away, but it will not send video signal to the Monitor, and pressing the power button again does not switch it off (I have to hold it for the 4 secs to power down.) A keyboard and mouse must be detected for the system to boot. I use the Wireless MultiMedia model. Your kbd/mouse is not being properly detected. Since it does run correctly using the reset, consider leaving the power on at shutdown, and just using reset to start your system. (works fine for me running W'98) Since your board has two ps/2 ports, try using the green adapter plug that came with your unit. Some systems don't detect well using the USB. Try running both keyboard and mouse on the ps/2 ports. Go to system properties and see that the set is named properly...... if so install new driver from your OS disc. Replace the cheap batteries that came with the unit with new alkaline batteries. Go to control panel and try the "add new hardware" utility to see if you can get it to load a new keyboard driver. It's a MS unit, so I would try to load drivers from your OS disc. Failing that, try to make a new boot disc and see if you can get it to boot properly. If you can get it to boot from a boot disc, I would remove the kbd/mouse from system/device manager, and boot from the boot disc in the hope that it will detect it as new hardware and load the correct driver set. If I hit the reset button, the whole thing fires up fine, If I connect a different Keyboard to the PS/2 it fires up fine. I've tried changing the wireless channel and this has no effect. If I disconnect the wireless K/B, power up with a different K/B, power down, reconnect the Wireless K/B, it fires up OK on the FIRST attempt ONLY. |
#10
|
|||
|
|||
Microsoft Keyboard Causes Bootup to hang
A mouse is not required for the bios to complete, and access the OS
partition. "Pepperoni" wrote in message ... "Walmsley's" wrote in message ... Hi I've got a brand new PC (pre-built):- P4 3.2ghz HT 512mb ddr 400mhz RAM Asus P4P800SE Mo/Bo (Latest BIOS) 200GB S-ATA Maxtor Drive Windows XP Home I've connected a new Wireless Keyboard and mouse from Microsoft (optical wireless desktop Elite) - LATEST drivers The Wireless hub has 2 cables running from it. 1 is for the PS/2 connection to the PC, the other is USB for the mouse. When I connect the Keyboard to the PS/2 socket the system will not boot. It powers up, and the H/D light flickers away, but it will not send video signal to the Monitor, and pressing the power button again does not switch it off (I have to hold it for the 4 secs to power down.) A keyboard and mouse must be detected for the system to boot. I use the Wireless MultiMedia model. Your kbd/mouse is not being properly detected. Since it does run correctly using the reset, consider leaving the power on at shutdown, and just using reset to start your system. (works fine for me running W'98) Since your board has two ps/2 ports, try using the green adapter plug that came with your unit. Some systems don't detect well using the USB. Try running both keyboard and mouse on the ps/2 ports. Go to system properties and see that the set is named properly...... if so install new driver from your OS disc. Replace the cheap batteries that came with the unit with new alkaline batteries. Go to control panel and try the "add new hardware" utility to see if you can get it to load a new keyboard driver. It's a MS unit, so I would try to load drivers from your OS disc. Failing that, try to make a new boot disc and see if you can get it to boot properly. If you can get it to boot from a boot disc, I would remove the kbd/mouse from system/device manager, and boot from the boot disc in the hope that it will detect it as new hardware and load the correct driver set. If I hit the reset button, the whole thing fires up fine, If I connect a different Keyboard to the PS/2 it fires up fine. I've tried changing the wireless channel and this has no effect. If I disconnect the wireless K/B, power up with a different K/B, power down, reconnect the Wireless K/B, it fires up OK on the FIRST attempt ONLY. |
#11
|
|||
|
|||
Microsoft Keyboard Causes Bootup to hang
A mouse is not required for the bios to complete, and access the OS
partition. "Pepperoni" wrote in message ... "Walmsley's" wrote in message ... Hi I've got a brand new PC (pre-built):- P4 3.2ghz HT 512mb ddr 400mhz RAM Asus P4P800SE Mo/Bo (Latest BIOS) 200GB S-ATA Maxtor Drive Windows XP Home I've connected a new Wireless Keyboard and mouse from Microsoft (optical wireless desktop Elite) - LATEST drivers The Wireless hub has 2 cables running from it. 1 is for the PS/2 connection to the PC, the other is USB for the mouse. When I connect the Keyboard to the PS/2 socket the system will not boot. It powers up, and the H/D light flickers away, but it will not send video signal to the Monitor, and pressing the power button again does not switch it off (I have to hold it for the 4 secs to power down.) A keyboard and mouse must be detected for the system to boot. I use the Wireless MultiMedia model. Your kbd/mouse is not being properly detected. Since it does run correctly using the reset, consider leaving the power on at shutdown, and just using reset to start your system. (works fine for me running W'98) Since your board has two ps/2 ports, try using the green adapter plug that came with your unit. Some systems don't detect well using the USB. Try running both keyboard and mouse on the ps/2 ports. Go to system properties and see that the set is named properly...... if so install new driver from your OS disc. Replace the cheap batteries that came with the unit with new alkaline batteries. Go to control panel and try the "add new hardware" utility to see if you can get it to load a new keyboard driver. It's a MS unit, so I would try to load drivers from your OS disc. Failing that, try to make a new boot disc and see if you can get it to boot properly. If you can get it to boot from a boot disc, I would remove the kbd/mouse from system/device manager, and boot from the boot disc in the hope that it will detect it as new hardware and load the correct driver set. If I hit the reset button, the whole thing fires up fine, If I connect a different Keyboard to the PS/2 it fires up fine. I've tried changing the wireless channel and this has no effect. If I disconnect the wireless K/B, power up with a different K/B, power down, reconnect the Wireless K/B, it fires up OK on the FIRST attempt ONLY. |
#12
|
|||
|
|||
Microsoft Keyboard Causes Bootup to hang
Go into the Bios and disable Fast Booting. It should be fine then
"Pepperoni" wrote in message ... "Walmsley's" wrote in message ... Hi I've got a brand new PC (pre-built):- P4 3.2ghz HT 512mb ddr 400mhz RAM Asus P4P800SE Mo/Bo (Latest BIOS) 200GB S-ATA Maxtor Drive Windows XP Home I've connected a new Wireless Keyboard and mouse from Microsoft (optical wireless desktop Elite) - LATEST drivers The Wireless hub has 2 cables running from it. 1 is for the PS/2 connection to the PC, the other is USB for the mouse. When I connect the Keyboard to the PS/2 socket the system will not boot. It powers up, and the H/D light flickers away, but it will not send video signal to the Monitor, and pressing the power button again does not switch it off (I have to hold it for the 4 secs to power down.) A keyboard and mouse must be detected for the system to boot. I use the Wireless MultiMedia model. Your kbd/mouse is not being properly detected. Since it does run correctly using the reset, consider leaving the power on at shutdown, and just using reset to start your system. (works fine for me running W'98) Since your board has two ps/2 ports, try using the green adapter plug that came with your unit. Some systems don't detect well using the USB. Try running both keyboard and mouse on the ps/2 ports. Go to system properties and see that the set is named properly...... if so install new driver from your OS disc. Replace the cheap batteries that came with the unit with new alkaline batteries. Go to control panel and try the "add new hardware" utility to see if you can get it to load a new keyboard driver. It's a MS unit, so I would try to load drivers from your OS disc. Failing that, try to make a new boot disc and see if you can get it to boot properly. If you can get it to boot from a boot disc, I would remove the kbd/mouse from system/device manager, and boot from the boot disc in the hope that it will detect it as new hardware and load the correct driver set. If I hit the reset button, the whole thing fires up fine, If I connect a different Keyboard to the PS/2 it fires up fine. I've tried changing the wireless channel and this has no effect. If I disconnect the wireless K/B, power up with a different K/B, power down, reconnect the Wireless K/B, it fires up OK on the FIRST attempt ONLY. |
#13
|
|||
|
|||
Microsoft Keyboard Causes Bootup to hang
I've tried every combination of USB devices. Bottom line is, if the Keyboard
is attached, the system hangs. I've done it with JUST the keyboard attached, it's PS2. Weird fault!! Nik. "Rob Hemmings" wrote in message ... "Walmsley's" wrote in message ... Hi I've got a brand new PC (pre-built):- P4 3.2ghz HT 512mb ddr 400mhz RAM Asus P4P800SE Mo/Bo (Latest BIOS) 200GB S-ATA Maxtor Drive Windows XP Home I've connected a new Wireless Keyboard and mouse from Microsoft (optical wireless desktop Elite) - LATEST drivers The Wireless hub has 2 cables running from it. 1 is for the PS/2 connection to the PC, the other is USB for the mouse. When I connect the Keyboard to the PS/2 socket the system will not boot. It powers up, and the H/D light flickers away, but it will not send video signal to the Monitor, and pressing the power button again does not switch it off (I have to hold it for the 4 secs to power down.) If I hit the reset button, the whole thing fires up fine, If I connect a different Keyboard to the PS/2 it fires up fine. I've tried changing the wireless channel and this has no effect. If I disconnect the wireless K/B, power up with a different K/B, power down, reconnect the Wireless K/B, it fires up OK on the FIRST attempt ONLY. A very bizarre problem! I'm hoping someone else out there has had this problem, and solved it! Any advice on this greatly appreciated! Have a look in the BIOS and see if "Legacy USB mouse/keyboad support" (or similar) is enabled. Try it with both settings. It could also be that your USB devices are taking too much power from the USB bus - try disconnecting all USB devices other than mouse/keyboard. If that's no help, I suggest you go through the steps that "Pepperoni" suggests. HTH -- Rob |
#14
|
|||
|
|||
Microsoft Keyboard Causes Bootup to hang
Go into the Bios and disable Fast Booting. It should be fine then
"Pepperoni" wrote in message ... "Walmsley's" wrote in message ... Hi I've got a brand new PC (pre-built):- P4 3.2ghz HT 512mb ddr 400mhz RAM Asus P4P800SE Mo/Bo (Latest BIOS) 200GB S-ATA Maxtor Drive Windows XP Home I've connected a new Wireless Keyboard and mouse from Microsoft (optical wireless desktop Elite) - LATEST drivers The Wireless hub has 2 cables running from it. 1 is for the PS/2 connection to the PC, the other is USB for the mouse. When I connect the Keyboard to the PS/2 socket the system will not boot. It powers up, and the H/D light flickers away, but it will not send video signal to the Monitor, and pressing the power button again does not switch it off (I have to hold it for the 4 secs to power down.) A keyboard and mouse must be detected for the system to boot. I use the Wireless MultiMedia model. Your kbd/mouse is not being properly detected. Since it does run correctly using the reset, consider leaving the power on at shutdown, and just using reset to start your system. (works fine for me running W'98) Since your board has two ps/2 ports, try using the green adapter plug that came with your unit. Some systems don't detect well using the USB. Try running both keyboard and mouse on the ps/2 ports. Go to system properties and see that the set is named properly...... if so install new driver from your OS disc. Replace the cheap batteries that came with the unit with new alkaline batteries. Go to control panel and try the "add new hardware" utility to see if you can get it to load a new keyboard driver. It's a MS unit, so I would try to load drivers from your OS disc. Failing that, try to make a new boot disc and see if you can get it to boot properly. If you can get it to boot from a boot disc, I would remove the kbd/mouse from system/device manager, and boot from the boot disc in the hope that it will detect it as new hardware and load the correct driver set. If I hit the reset button, the whole thing fires up fine, If I connect a different Keyboard to the PS/2 it fires up fine. I've tried changing the wireless channel and this has no effect. If I disconnect the wireless K/B, power up with a different K/B, power down, reconnect the Wireless K/B, it fires up OK on the FIRST attempt ONLY. |
#15
|
|||
|
|||
Microsoft Keyboard Causes Bootup to hang
I've tried every combination of USB devices. Bottom line is, if the Keyboard
is attached, the system hangs. I've done it with JUST the keyboard attached, it's PS2. Weird fault!! Nik. "Rob Hemmings" wrote in message ... "Walmsley's" wrote in message ... Hi I've got a brand new PC (pre-built):- P4 3.2ghz HT 512mb ddr 400mhz RAM Asus P4P800SE Mo/Bo (Latest BIOS) 200GB S-ATA Maxtor Drive Windows XP Home I've connected a new Wireless Keyboard and mouse from Microsoft (optical wireless desktop Elite) - LATEST drivers The Wireless hub has 2 cables running from it. 1 is for the PS/2 connection to the PC, the other is USB for the mouse. When I connect the Keyboard to the PS/2 socket the system will not boot. It powers up, and the H/D light flickers away, but it will not send video signal to the Monitor, and pressing the power button again does not switch it off (I have to hold it for the 4 secs to power down.) If I hit the reset button, the whole thing fires up fine, If I connect a different Keyboard to the PS/2 it fires up fine. I've tried changing the wireless channel and this has no effect. If I disconnect the wireless K/B, power up with a different K/B, power down, reconnect the Wireless K/B, it fires up OK on the FIRST attempt ONLY. A very bizarre problem! I'm hoping someone else out there has had this problem, and solved it! Any advice on this greatly appreciated! Have a look in the BIOS and see if "Legacy USB mouse/keyboad support" (or similar) is enabled. Try it with both settings. It could also be that your USB devices are taking too much power from the USB bus - try disconnecting all USB devices other than mouse/keyboard. If that's no help, I suggest you go through the steps that "Pepperoni" suggests. HTH -- Rob |
Thread Tools | |
Display Modes | |
|
|