If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
broadband two pc how
im moving over from dialup to broadband, i have two pc one downstairs and one upstairs, neither have ethernet cards
what is the best way of setting up the connection from the broadband modem downstairs, will have to run cables up stairs for the pc. exactly what do i need to get it up and running for both desktops im running xp pro |
Ads |
#2
|
|||
|
|||
broadband two pc how
fender62 wrote:
im moving over from dialup to broadband, i have two pc one downstairs and one upstairs, neither have ethernet cards what is the best way of setting up the connection from the broadband modem downstairs, will have to run cables up stairs for the pc. exactly what do i need to get it up and running for both desktops im running xp pro The best way of accomplishing this is to network your computers using a router. Depending on the construction of your home and the distance(s) between the computers and the place where your broadband modem and router will be located, you can do this wirelessly. On the other hand, if running an Ethernet cable from the router to the computers is easy for you to do, that will result in a more secure, more reliable, and somewhat faster local network. Ethernet adapters for desktop computers are quite inexpensive. Although it is possible to get a USB to Ethernet adapter, if you have a free PCI slot in your desktops, you should get a pci card adapter. Even if you plan to use a wireless network, you will want at least on Ethernet adapter that you will use to configure your router. There really is no need to buy anything other than a "10/100" adapter (if you think you can run cables through your house, you could consider buying "Gigabit" 10/100/1000 adapters, although with Win XP, the increase in throughput will not be as much as you might think). Just as an example, see http://www.compusa.com/products/products.asp?N=200140 http://www.newegg.com/Product/Produc...et+pci+adapter If you go wireless, in addition to the router, you will need a wireless adapter for each computer. Here also, you can get either pci card or usb adapters. With wireless adapters, however, the usb versions have the advantage that you can use a short USB extension cord (sometimes supplied with the adapter) to position the adapter and its antenna in a more optimum place than down behind the computer case. Some pci card wireless adapters have detachable antennas that can similarly be relocated. The current wireless standard is 802.11G, although some of the newer 802.11N (not yet ratified as a standard) devices apparently are behaving nicely. Get a name brand: Linksys, D-Link, Netgear, Buffalo or similar. Personally, I've had good experience with Linksys. This is a pretty good router, and it includes a built-in rf-amplifier: http://www.newegg.com/Product/Produc...82E16833162134 And this 802.11n router has been recommended in this newgroup: http://www.dlink.com/products/?pid=530 I suggest that you stick to the same brand and "family" for wireless adapters that you select for the router. In other words, if you choose to get the D-Link Xtreme N Gigabit Router (DIR-655), then get the D-Link Xtreme N Gigabit adapters shown on the product spec page. If you get the Buffalo WHP-HP-G54, Buffalo does not offer a corresponding "MIMO" adapter for desktops; you'd probably do best with one of Buffalo's "Wireless G 125" family of adapters. For general info on setting up networks, see http://www.ezlan.net/ http://www.microsoft.com/windowsxp/u...g/default.mspx -- Lem MS MVP -- Networking To the moon and back with 64 Kbits of RAM and 512 Kbits of ROM. http://en.wikipedia.org/wiki/Apollo_Guidance_Computer |
Thread Tools | |
Display Modes | |
|
|