If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#16
|
|||
|
|||
Automatic private address in network connections
On Tue, 20 Apr 2004 10:42:02 -0700, Moses wrote:
-----Original Message----- On Tue, 20 Apr 2004 07:39:30 -0700, Moses wrote: I have two computers that can not access internet, or the network. In network connections, I can click on LAN or High Speed Internet, and in the Details section it states that it is enabled and this: IP Address: 169.254.x.y Subnet Mask: 255.255.0.0 Automatic Private Address What is this Automatic Private Address, and how do I get rid of it? My other computer says 'Assigned by DHCP' and it works fine. How do I change this one back to DCHP, so it will also work. The 169. address indicates that your computer is set to obtain an IP Address by dhcp but a dhcp server is not available or can not be connected to. Check all connections and NIC. . Everything is securely connected, and I've tried different NICs, Also this is just a peer to peer network w/ no server. Did you try ipconfig /renew? If so what was the result? |
Ads |
#17
|
|||
|
|||
Automatic private address in network connections
-----Original Message----- Moses wrote: I have two computers that can not access internet, or the network. In network connections, I can click on LAN or High Speed Internet, and in the Details section it states that it is enabled and this: IP Address: 169.254.x.y Subnet Mask: 255.255.0.0 Automatic Private Address What is this Automatic Private Address, and how do I get rid of it? My other computer says 'Assigned by DHCP' and it works fine. How do I change this one back to DCHP, so it will also work. Describe your LAN cabling a bit, and how you connect to the web: do you have a simple (non-routing) hub or a router? Do both PCs connect to downlink ports on the hub/router/switch? Does the uplink port on the hub/router/switch go to a cable/DSL modem? Are the cables all standard Cat5 cables, or are some crossover cables? -- Cheers, Bob Our Modem plugs into the WAN port of our router, and our hub is connected through the uplink plug to the LAN port on the router. Our computers are plugged stright into the hub. We have no server, but just a peer to peer network with six computers. We use the CAT5e cables, and no crossover cables are used in the whole setup. |
#18
|
|||
|
|||
Automatic private address in network connections
Moses wrote:
I have two computers that can not access internet, or the network. In network connections, I can click on LAN or High Speed Internet, and in the Details section it states that it is enabled and this: IP Address: 169.254.x.y Subnet Mask: 255.255.0.0 Automatic Private Address What is this Automatic Private Address, and how do I get rid of it? My other computer says 'Assigned by DHCP' and it works fine. How do I change this one back to DCHP, so it will also work. Describe your LAN cabling a bit, and how you connect to the web: do you have a simple (non-routing) hub or a router? Do both PCs connect to downlink ports on the hub/router/switch? Does the uplink port on the hub/router/switch go to a cable/DSL modem? Are the cables all standard Cat5 cables, or are some crossover cables? -- Cheers, Bob |
#19
|
|||
|
|||
Automatic private address in network connections
Moses wrote:
I have two computers that can not access internet, or the network. In network connections, I can click on LAN or High Speed Internet, and in the Details section it states that it is enabled and this: IP Address: 169.254.x.y Subnet Mask: 255.255.0.0 Automatic Private Address What is this Automatic Private Address, and how do I get rid of it? My other computer says 'Assigned by DHCP' and it works fine. How do I change this one back to DCHP, so it will also work. Describe your LAN cabling a bit, and how you connect to the web: do you have a simple (non-routing) hub or a router? Do both PCs connect to downlink ports on the hub/router/switch? Does the uplink port on the hub/router/switch go to a cable/DSL modem? Are the cables all standard Cat5 cables, or are some crossover cables? -- Cheers, Bob |
#20
|
|||
|
|||
Automatic private address in network connections
Moses wrote:
I have two computers that can not access internet, or the network. In network connections, I can click on LAN or High Speed Internet, and in the Details section it states that it is enabled and this: IP Address: 169.254.x.y Subnet Mask: 255.255.0.0 Automatic Private Address What is this Automatic Private Address, and how do I get rid of it? My other computer says 'Assigned by DHCP' and it works fine. How do I change this one back to DCHP, so it will also work. Describe your LAN cabling a bit, and how you connect to the web: do you have a simple (non-routing) hub or a router? Do both PCs connect to downlink ports on the hub/router/switch? Does the uplink port on the hub/router/switch go to a cable/DSL modem? Are the cables all standard Cat5 cables, or are some crossover cables? -- Cheers, Bob |
#21
|
|||
|
|||
Automatic private address in network connections
Moses wrote:
I have two computers that can not access internet, or the network. In network connections, I can click on LAN or High Speed Internet, and in the Details section it states that it is enabled and this: IP Address: 169.254.x.y Subnet Mask: 255.255.0.0 Automatic Private Address What is this Automatic Private Address, and how do I get rid of it? My other computer says 'Assigned by DHCP' and it works fine. How do I change this one back to DCHP, so it will also work. Describe your LAN cabling a bit, and how you connect to the web: do you have a simple (non-routing) hub or a router? Do both PCs connect to downlink ports on the hub/router/switch? Does the uplink port on the hub/router/switch go to a cable/DSL modem? Are the cables all standard Cat5 cables, or are some crossover cables? -- Cheers, Bob |
#22
|
|||
|
|||
Automatic private address in network connections
I have a similar problem with one computer on a wireless
network. A Netgear router handles the DHCP chores, but one of the computers can't see it. The network connection status box on that computer says that it has an excellent connection, but it's not getting any guidance from the router. WEP is enabled on the router and computer, and even if I enter a false key in the computer, it still says that there is a good connection. Connecting to the router with a cable works perfectly. All of the other computers in the network connect well wirelessly. -----Original Message----- Moses wrote: I have two computers that can not access internet, or the network. In network connections, I can click on LAN or High Speed Internet, and in the Details section it states that it is enabled and this: IP Address: 169.254.x.y Subnet Mask: 255.255.0.0 Automatic Private Address What is this Automatic Private Address, and how do I get rid of it? My other computer says 'Assigned by DHCP' and it works fine. How do I change this one back to DCHP, so it will also work. Describe your LAN cabling a bit, and how you connect to the web: do you have a simple (non-routing) hub or a router? Do both PCs connect to downlink ports on the hub/router/switch? Does the uplink port on the hub/router/switch go to a cable/DSL modem? Are the cables all standard Cat5 cables, or are some crossover cables? -- Cheers, Bob . |
#23
|
|||
|
|||
Automatic private address in network connections
-----Original Message----- On Tue, 20 Apr 2004 12:52:59 -0700, wrote: snip Did you try ipconfig /renew? If so what was the result? . An error occoured while renewing interface Local Area Connection : An operation was attempted on somethingthat is not a socket Your winsock may be corrupted. Try reinstalling networking on that computer or see: http://support.microsoft.com/default.aspx?scid=kb;en- us;817571 http://www.jsiinc.com/SUBN/tip6600/rh6613.htm http://www.jsiinc.com/SUBK/tip5200/rh5241.htm . Thanks BobC That solved my problem Many, many Thanks! |
#24
|
|||
|
|||
Automatic private address in network connections
I have a similar problem with one computer on a wireless
network. A Netgear router handles the DHCP chores, but one of the computers can't see it. The network connection status box on that computer says that it has an excellent connection, but it's not getting any guidance from the router. WEP is enabled on the router and computer, and even if I enter a false key in the computer, it still says that there is a good connection. Connecting to the router with a cable works perfectly. All of the other computers in the network connect well wirelessly. -----Original Message----- Moses wrote: I have two computers that can not access internet, or the network. In network connections, I can click on LAN or High Speed Internet, and in the Details section it states that it is enabled and this: IP Address: 169.254.x.y Subnet Mask: 255.255.0.0 Automatic Private Address What is this Automatic Private Address, and how do I get rid of it? My other computer says 'Assigned by DHCP' and it works fine. How do I change this one back to DCHP, so it will also work. Describe your LAN cabling a bit, and how you connect to the web: do you have a simple (non-routing) hub or a router? Do both PCs connect to downlink ports on the hub/router/switch? Does the uplink port on the hub/router/switch go to a cable/DSL modem? Are the cables all standard Cat5 cables, or are some crossover cables? -- Cheers, Bob . |
#25
|
|||
|
|||
Automatic private address in network connections
I have a similar problem with one computer on a wireless
network. A Netgear router handles the DHCP chores, but one of the computers can't see it. The network connection status box on that computer says that it has an excellent connection, but it's not getting any guidance from the router. WEP is enabled on the router and computer, and even if I enter a false key in the computer, it still says that there is a good connection. Connecting to the router with a cable works perfectly. All of the other computers in the network connect well wirelessly. -----Original Message----- Moses wrote: I have two computers that can not access internet, or the network. In network connections, I can click on LAN or High Speed Internet, and in the Details section it states that it is enabled and this: IP Address: 169.254.x.y Subnet Mask: 255.255.0.0 Automatic Private Address What is this Automatic Private Address, and how do I get rid of it? My other computer says 'Assigned by DHCP' and it works fine. How do I change this one back to DCHP, so it will also work. Describe your LAN cabling a bit, and how you connect to the web: do you have a simple (non-routing) hub or a router? Do both PCs connect to downlink ports on the hub/router/switch? Does the uplink port on the hub/router/switch go to a cable/DSL modem? Are the cables all standard Cat5 cables, or are some crossover cables? -- Cheers, Bob . |
#26
|
|||
|
|||
Automatic private address in network connections
I have a similar problem with one computer on a wireless
network. A Netgear router handles the DHCP chores, but one of the computers can't see it. The network connection status box on that computer says that it has an excellent connection, but it's not getting any guidance from the router. WEP is enabled on the router and computer, and even if I enter a false key in the computer, it still says that there is a good connection. Connecting to the router with a cable works perfectly. All of the other computers in the network connect well wirelessly. -----Original Message----- Moses wrote: I have two computers that can not access internet, or the network. In network connections, I can click on LAN or High Speed Internet, and in the Details section it states that it is enabled and this: IP Address: 169.254.x.y Subnet Mask: 255.255.0.0 Automatic Private Address What is this Automatic Private Address, and how do I get rid of it? My other computer says 'Assigned by DHCP' and it works fine. How do I change this one back to DCHP, so it will also work. Describe your LAN cabling a bit, and how you connect to the web: do you have a simple (non-routing) hub or a router? Do both PCs connect to downlink ports on the hub/router/switch? Does the uplink port on the hub/router/switch go to a cable/DSL modem? Are the cables all standard Cat5 cables, or are some crossover cables? -- Cheers, Bob . |
#27
|
|||
|
|||
Automatic private address in network connections
Xref: kermit microsoft.public.windowsxp.network_web:199676
-----Original Message----- On Tue, 20 Apr 2004 10:42:02 -0700, Moses wrote: -----Original Message----- On Tue, 20 Apr 2004 07:39:30 -0700, Moses wrote: I have two computers that can not access internet, or the network. In network connections, I can click on LAN or High Speed Internet, and in the Details section it states that it is enabled and this: IP Address: 169.254.x.y Subnet Mask: 255.255.0.0 Automatic Private Address What is this Automatic Private Address, and how do I get rid of it? My other computer says 'Assigned by DHCP' and it works fine. How do I change this one back to DCHP, so it will also work. The 169. address indicates that your computer is set to obtain an IP Address by dhcp but a dhcp server is not available or can not be connected to. Check all connections and NIC. . Everything is securely connected, and I've tried different NICs, Also this is just a peer to peer network w/ no server. Did you try ipconfig /renew? If so what was the result? . An error occoured while renewing interface Local Area Connection : An operation was attempted on somethingthat is not a socket |
#28
|
|||
|
|||
Automatic private address in network connections
Xref: kermit microsoft.public.windowsxp.network_web:199676
-----Original Message----- On Tue, 20 Apr 2004 10:42:02 -0700, Moses wrote: -----Original Message----- On Tue, 20 Apr 2004 07:39:30 -0700, Moses wrote: I have two computers that can not access internet, or the network. In network connections, I can click on LAN or High Speed Internet, and in the Details section it states that it is enabled and this: IP Address: 169.254.x.y Subnet Mask: 255.255.0.0 Automatic Private Address What is this Automatic Private Address, and how do I get rid of it? My other computer says 'Assigned by DHCP' and it works fine. How do I change this one back to DCHP, so it will also work. The 169. address indicates that your computer is set to obtain an IP Address by dhcp but a dhcp server is not available or can not be connected to. Check all connections and NIC. . Everything is securely connected, and I've tried different NICs, Also this is just a peer to peer network w/ no server. Did you try ipconfig /renew? If so what was the result? . An error occoured while renewing interface Local Area Connection : An operation was attempted on somethingthat is not a socket |
#29
|
|||
|
|||
Automatic private address in network connections
Xref: kermit microsoft.public.windowsxp.network_web:199676
-----Original Message----- On Tue, 20 Apr 2004 10:42:02 -0700, Moses wrote: -----Original Message----- On Tue, 20 Apr 2004 07:39:30 -0700, Moses wrote: I have two computers that can not access internet, or the network. In network connections, I can click on LAN or High Speed Internet, and in the Details section it states that it is enabled and this: IP Address: 169.254.x.y Subnet Mask: 255.255.0.0 Automatic Private Address What is this Automatic Private Address, and how do I get rid of it? My other computer says 'Assigned by DHCP' and it works fine. How do I change this one back to DCHP, so it will also work. The 169. address indicates that your computer is set to obtain an IP Address by dhcp but a dhcp server is not available or can not be connected to. Check all connections and NIC. . Everything is securely connected, and I've tried different NICs, Also this is just a peer to peer network w/ no server. Did you try ipconfig /renew? If so what was the result? . An error occoured while renewing interface Local Area Connection : An operation was attempted on somethingthat is not a socket |
#30
|
|||
|
|||
Automatic private address in network connections
On Tue, 20 Apr 2004 12:52:59 -0700,
wrote: snip Did you try ipconfig /renew? If so what was the result? . An error occoured while renewing interface Local Area Connection : An operation was attempted on somethingthat is not a socket Your winsock may be corrupted. Try reinstalling networking on that computer or see: http://support.microsoft.com/default...b;en-us;817571 http://www.jsiinc.com/SUBN/tip6600/rh6613.htm http://www.jsiinc.com/SUBK/tip5200/rh5241.htm |
Thread Tools | |
Display Modes | |
|
|