If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Rate Thread | Display Modes |
#1
|
|||
|
|||
HDD LED
This is strange. From case 2 wires in a 4 hole socket [2 centre holes
empty]. MB only 2 prongs on the plug. Is there a simple way round this? housetrained |
Ads |
#2
|
|||
|
|||
HDD LED
Sorry wrong group
"housetrained" wrote in message ... This is strange. From case 2 wires in a 4 hole socket [2 centre holes empty]. MB only 2 prongs on the plug. Is there a simple way round this? housetrained |
#3
|
|||
|
|||
HDD LED
On Wed, 9 Jan 2013 11:41:18 -0000, housetrained wrote:
This is strange. From case 2 wires in a 4 hole socket [2 centre holes empty]. MB only 2 prongs on the plug. Is there a simple way round this? housetrained That sounds like the speaker connection, I think. -- Regards - Rodney Pont The from address exists but is mostly dumped, please send any emails to the address below e-mail rpont (at) gmail (dot) com |
#4
|
|||
|
|||
HDD LED
On Wed, 9 Jan 2013 11:41:18 -0000, housetrained wrote:
This is strange. From case 2 wires in a 4 hole socket [2 centre holes empty]. MB only 2 prongs on the plug. Is there a simple way round this? housetrained Two ways I have used: 1. Make a short 2-wire cable with a 4-prong male plug at one end and a two-prong female plug at the other. Wire it the obvious way. 2. Manage to get one insert out of its hole and put it in the hole next to the other insert. OTOH, as Rodney Pont said, it does sound like the speaker plug. -- Gene E. Bloch (Stumbling Bloch) |
#5
|
|||
|
|||
HDD LED
"Gene E. Bloch" wrote in message ... On Wed, 9 Jan 2013 11:41:18 -0000, housetrained wrote: This is strange. From case 2 wires in a 4 hole socket [2 centre holes empty]. MB only 2 prongs on the plug. Is there a simple way round this? housetrained Two ways I have used: 1. Make a short 2-wire cable with a 4-prong male plug at one end and a two-prong female plug at the other. Wire it the obvious way. 2. Manage to get one insert out of its hole and put it in the hole next to the other insert. OTOH, as Rodney Pont said, it does sound like the speaker plug. It was the HDD LED but i cut it in half and used the singles Thanks all. housetrained -- * I promise I will format my posts properly in the future. * Windows Live Mail just can't quote! Luckily, I have found this: * http://www.dusko-lolic.from.hr/wlmquote/ |
#6
|
|||
|
|||
HDD LED
On Wed, 9 Jan 2013 22:41:58 -0000, housetrained wrote:
"Gene E. Bloch" wrote in message ... On Wed, 9 Jan 2013 11:41:18 -0000, housetrained wrote: This is strange. From case 2 wires in a 4 hole socket [2 centre holes empty]. MB only 2 prongs on the plug. Is there a simple way round this? housetrained Two ways I have used: 1. Make a short 2-wire cable with a 4-prong male plug at one end and a two-prong female plug at the other. Wire it the obvious way. 2. Manage to get one insert out of its hole and put it in the hole next to the other insert. OTOH, as Rodney Pont said, it does sound like the speaker plug. It was the HDD LED but i cut it in half and used the singles Thanks all. housetrained That was method #3 :-) Good thinking... -- Gene E. Bloch (Stumbling Bloch) |
Thread Tools | |
Display Modes | Rate This Thread |
|
|