If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Rate Thread | Display Modes |
#1
|
|||
|
|||
"Active" hard disk query
I just noticed under Disk Management that one of my external drives is marked "Active" as well as "Primary" like the other attached drives. I understand what "Active" means but in this case that has to be wrong as I'm sure there's no OS to boot on that drive. In fact sure it's never had one on it. I've found a page telling me how to remove the "Active" flag using DiskPart but am wondering if I should as system works and boots fine as is. I'm assuming no data would be lost doing that. As a sidenote - wondering if this might be why Backup-Restore won't create an image on this same drive but will on the others? |
Ads |
#2
|
|||
|
|||
"Active" hard disk query
pjp wrote:
I just noticed under Disk Management that one of my external drives is marked "Active" as well as "Primary" like the other attached drives. I understand what "Active" means but in this case that has to be wrong as I'm sure there's no OS to boot on that drive. In fact sure it's never had one on it. I've found a page telling me how to remove the "Active" flag using DiskPart but am wondering if I should as system works and boots fine as is. I'm assuming no data would be lost doing that. As a sidenote - wondering if this might be why Backup-Restore won't create an image on this same drive but will on the others? The way I understand the syntax for System Image, it captures the system partition, plus others of your choosing. I think I ran into this, when testing backup to DVD. I *had* to include the C: partition, which means it cost me four DVDs minimum to do some testing, and took forever. It wouldn't do just my little test data partition, which would have fit on one DVD. So my assumption is, it needs at least one system partition. A Windows 7 install, can be one or two partitions. Two partition installs are used for compatibility with BitLocker full disk encryption. BitLocker encrypts C:, so your tiny boot partition (known as SystemReserved) can remain unencrypted and start the boot process far enough, to decrypt and boot C:. So that takes two partitions to achieve. If you never use BitLocker, there's really no reason to have two partitions. And you can actually shrink a two partition install, down to one again. There's a recipe for that. System Images can also be done from the command line. These are examples from my notes files. The boot partition doesn't have a drive letter (on purpose), so requires screwing around. To pick up the boot partition (has a Boot folder), you use a GUID to pick the volume. As a convenient shorthand (so you don't have to do it that way), the "-allCritlcal" selects C: and boot partition if one is present. ******* This command, backs up a C: and a Boot (SystemReserved), and stores the resulting .vhd files on F:\ Wbadmin start backup -backupTarget:F: -include:\\?\Volume{C38A95FE-9261-11E1-92E9-806E6F6E6963}\,C: -quiet This example has some redundancy in the command. The allCritical already gets C, so no need to list C separately. The output goes on partition E:\ wbAdmin start backup -backupTarget:E: -include:C:,D:,F: -allCritical -quiet This stores C: and Boot on N: . I dropped the "quiet" for this one. wbAdmin start backup -backupTarget:N: -allCritical You can also restore using wbadmin, and Microsoft has a web page with many different samples of commands you can use. ******* So your theory might have some merit. Maybe an errant boot flag (Active), is enough to screw up a "basic" backup. Just be sure you understand how that boot flag got there, before removing it. The boot flag (0x80 Hex), could be put back with Diskpart from Recovery Console, or using a Linux LiveCD. So you have lots of options - if you were prepared in advance to repair broken Windows boxen... You might even do it with PTEDIT32, just for spice of life reasons. PTEDIT32 allows typing over MBR data fields, convenient at times. I've swapped partition table entries and put them back in disk spacial order with this. This is where I got it, years ago. ftp://ftp.symantec.com/public/englis...s/PTEDIT32.zip The above post makes no mention of GPT disks. Many details there will differ, and PTEDIT32 would gag on a GPT disk. Your 2TB disk could still be an MBR disk. Your 3TB disk could be GPT, depending on what you used to gain access. I have a 3TB disk here, and use Acronis Capacity Manager driver, to turn it into a 2TB physical disk and a 1TB virtual disk. Since that drive is for backups only, I've never had to face the question of what happens when mixing ACM with wbadmin... Have fun, Paul |
#3
|
|||
|
|||
"Active" hard disk query
On Sun, 15 Feb 2015 18:24:03 -0400, pjp wrote:
I just noticed under Disk Management that one of my external drives is marked "Active" as well as "Primary" like the other attached drives. I understand what "Active" means but in this case that has to be wrong as I'm sure there's no OS to boot on that drive. In fact sure it's never had one on it. I've found a page telling me how to remove the "Active" flag using DiskPart but am wondering if I should as system works and boots fine as is. I'm assuming no data would be lost doing that. As a sidenote - wondering if this might be why Backup-Restore won't create an image on this same drive but will on the others? I googled Windows "active partition" and about half way down the first page found http://www.sevenforums.com/tutorials...rk-active.html which includes the statement "If you have multiple hard disks installed on your computer, it's possible for each hard disk to have a partition set as active. However, the active partition on the first hard disk that your computer's BIOS detects is the one that will start the computer." I could be wrong but I don't think there's any connection with Backup. After all, it backs up your C: drive, doesn't it? -- Stan Brown, Oak Road Systems, Tompkins County, New York, USA http://OakRoadSystems.com Shikata ga nai... |
#4
|
|||
|
|||
"Active" hard disk query
On Sun, 15 Feb 2015 18:24:03 -0400, pjp
wrote: I just noticed under Disk Management that one of my external drives is marked "Active" as well as "Primary" like the other attached drives. I understand what "Active" means but in this case that has to be wrong as I'm sure there's no OS to boot on that drive. In fact sure it's never had one on it. I've found a page telling me how to remove the "Active" flag using DiskPart but am wondering if I should as system works and boots fine as is. I'm assuming no data would be lost doing that. I had a bunch of data disks marked Active a year or so ago and I used Diskpart to remove the Active flag from all but the system drive. There were no ill effects. In fact, there was no noticeable behavior difference at all. As a sidenote - wondering if this might be why Backup-Restore won't create an image on this same drive but will on the others? Can't say. I don't use that tool. -- Char Jackson |
#5
|
|||
|
|||
"Active" hard disk query
On 02/15/2015 04:24 PM, pjp wrote:
I just noticed under Disk Management that one of my external drives is marked "Active" as well as "Primary" like the other attached drives. I understand what "Active" means but in this case that has to be wrong as I'm sure there's no OS to boot on that drive. In fact sure it's never had one on it. I've found a page telling me how to remove the "Active" flag using DiskPart but am wondering if I should as system works and boots fine as is. I'm assuming no data would be lost doing that. As a sidenote - wondering if this might be why Backup-Restore won't create an image on this same drive but will on the others? A drive that you do not boot from certainly does not have to be marked active...but I can't think of any reason it would hurt anything to just leave it as is. |
#6
|
|||
|
|||
"Active" hard disk query
|
Thread Tools | |
Display Modes | Rate This Thread |
|
|