If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
problem when trying to install software
I am trying to install new printer software and keep getting the following
message when I open the install CD. c:\WINDOWS\SYSTEM32\AUTOEXEC.NT The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. Hopefully some one can help with an easy fix. Thanks in advance. Rob |
Ads |
#2
|
|||
|
|||
problem when trying to install software
This might help copy autoexec.nt from c:\windows\repair to
c:\windows\system32 Good Luck -- William "arcticsnowman" wrote in message ... I am trying to install new printer software and keep getting the following message when I open the install CD. c:\WINDOWS\SYSTEM32\AUTOEXEC.NT The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. Hopefully some one can help with an easy fix. Thanks in advance. Rob |
#3
|
|||
|
|||
problem when trying to install software
Could you please be a bit more specific about the steps you want me to take?I
am wondering about the copy and repair to part. "WTC" wrote: This might help copy autoexec.nt from c:\windows\repair to c:\windows\system32 Good Luck -- William "arcticsnowman" wrote in message ... I am trying to install new printer software and keep getting the following message when I open the install CD. c:\WINDOWS\SYSTEM32\AUTOEXEC.NT The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. Hopefully some one can help with an easy fix. Thanks in advance. Rob |
#4
|
|||
|
|||
problem when trying to install software
Nevermind, I got ya figured out. Thanks very much--it worked. Thanks again!
"arcticsnowman" wrote: Could you please be a bit more specific about the steps you want me to take?I am wondering about the copy and repair to part. "WTC" wrote: This might help copy autoexec.nt from c:\windows\repair to c:\windows\system32 Good Luck -- William "arcticsnowman" wrote in message ... I am trying to install new printer software and keep getting the following message when I open the install CD. c:\WINDOWS\SYSTEM32\AUTOEXEC.NT The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. Hopefully some one can help with an easy fix. Thanks in advance. Rob |
#5
|
|||
|
|||
problem when trying to install software
Locate the folder c:\windows\repair
Find the autoexec.nt file right click on the autoexec.nt file and select "Copy to Folder..." then navigate to c:\windows\system32 then select ok -- William "arcticsnowman" wrote in message ... Could you please be a bit more specific about the steps you want me to take?I am wondering about the copy and repair to part. "WTC" wrote: This might help copy autoexec.nt from c:\windows\repair to c:\windows\system32 Good Luck -- William "arcticsnowman" wrote in message ... I am trying to install new printer software and keep getting the following message when I open the install CD. c:\WINDOWS\SYSTEM32\AUTOEXEC.NT The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. Hopefully some one can help with an easy fix. Thanks in advance. Rob |
#6
|
|||
|
|||
problem when trying to install software
Your welcome
-- William "arcticsnowman" wrote in message ... Nevermind, I got ya figured out. Thanks very much--it worked. Thanks again! "arcticsnowman" wrote: Could you please be a bit more specific about the steps you want me to take?I am wondering about the copy and repair to part. "WTC" wrote: This might help copy autoexec.nt from c:\windows\repair to c:\windows\system32 Good Luck -- William "arcticsnowman" wrote in message ... I am trying to install new printer software and keep getting the following message when I open the install CD. c:\WINDOWS\SYSTEM32\AUTOEXEC.NT The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. Hopefully some one can help with an easy fix. Thanks in advance. Rob |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Cannot install software from Administrator Profile | Adam Smith | Windows XP Help and Support | 1 | October 20th 04 03:01 AM |
PC Keeps Restarting! | Pink Sparkle Girl | Performance and Maintainance of XP | 3 | October 13th 04 02:47 AM |
PCI card install problem | Damien | Hardware and Windows XP | 3 | October 10th 04 02:30 AM |
software screen problem | amit | The Basics | 0 | September 23rd 04 08:55 AM |
Can't Install Softwa Some setup.exe files won't run on Win XP | java | Windows XP Help and Support | 0 | August 23rd 04 07:03 AM |