If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
How do I setup workgroup access with SP2?
How do I setup a new machine that came with Windows XP Professional
SP2 installed so that it has access to the existing workgroup? I made it be in the proper workgroup, made the administrator password the same as on the Windows XP Professional SP1 systems, and am using the same username and password on all of the machines. I disabled the firewall. The SP2 machine can't even reach the directories that it is sharing. For example, D: is shared as DXP1D, but both \\Dxp1 and \\DXP1 get no access permitted errors. |
Ads |
#2
|
|||
|
|||
How do I setup workgroup access with SP2?
Hi,
Not very clear about how you are trying to access a shared folder on your machine. 1) u do not need to have the same username password for all machines (to access shared folder in a workgrp, a guest account is good enough). 2) Other than giving the workgrp name to the new machine, you need to make sure that the IP address and Subnet mask assigned to the machine is correct. If the IP address is not in the right range or the Subnet Mask is incorrect - the machine will not be able to access any other computer in its workgroup. 3) to access a shared folder on your machine \\machinename\shared Shared - is the name you assigned to the shared folder for access on the network. Dxp1 is the name of your SP2 machine? 4) Make sure that File and Printer Sharing for Microsoft Networks is installed. Visit: http://compnetworking.about.com/cs/w...ient4msnet.htm I would assume, if its a fresh install. It could be an issue with the IP or Services not installed. ~A "Mark Fineman" wrote: How do I setup a new machine that came with Windows XP Professional SP2 installed so that it has access to the existing workgroup? I made it be in the proper workgroup, made the administrator password the same as on the Windows XP Professional SP1 systems, and am using the same username and password on all of the machines. I disabled the firewall. The SP2 machine can't even reach the directories that it is sharing. For example, D: is shared as DXP1D, but both \\Dxp1 and \\DXP1 get no access permitted errors. |
#3
|
|||
|
|||
How do I setup workgroup access with SP2?
"Mark Fineman" wrote in message
... How do I setup a new machine that came with Windows XP Professional SP2 installed so that it has access to the existing workgroup? I made it be in the proper workgroup, made the administrator password the same as on the Windows XP Professional SP1 systems, and am using the same username and password on all of the machines. I disabled the firewall. The SP2 machine can't even reach the directories that it is sharing. For example, D: is shared as DXP1D, but both \\Dxp1 and \\DXP1 get no access permitted errors. Did you run the Network Wizard on the new machine? -- Interim Systems and Management Accounting Gordon Burgess-Parker Director www.gbpcomputing.co.uk |
#4
|
|||
|
|||
How do I setup workgroup access with SP2?
I found the problem.
The new system came with Norton Security. I thought that I had turned it off as much as possible, but I missed at least one place where I had to put the LAN IP addresses (192.168.1.x) in a list of good guys. On Tue, 22 Mar 2005 22:55:02 -0800, "Aristarkhos" wrote in part: Hi, Not very clear about how you are trying to access a shared folder on your machine. 1) u do not need to have the same username password for all machines (to access shared folder in a workgrp, a guest account is good enough). Not for all access if your environment includes Windows 98 SE with multiple usernames, Windows 98 SE without usernames, and Windows XP Professional SP1 The other 3 comments were correct, but I had already checked them. Here is my original question: "Mark Fineman" wrote: How do I setup a new machine that came with Windows XP Professional SP2 installed so that it has access to the existing workgroup? I made it be in the proper workgroup, made the administrator password the same as on the Windows XP Professional SP1 systems, and am using the same username and password on all of the machines. I disabled the firewall. The SP2 machine can't even reach the directories that it is sharing. For example, D: is shared as DXP1D, but both \\Dxp1 and \\DXP1 get no access permitted errors. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Win XP cannot access its own files on Workgroup | Newsgroupie | Networking and the Internet with Windows XP | 4 | January 21st 05 05:33 PM |
File Access Problems in SP2 | Oldan | Windows Service Pack 2 | 3 | October 14th 04 10:26 PM |
Providing Internet Access to Computer in Workgroup | JR | Networking and the Internet with Windows XP | 0 | July 27th 04 12:12 AM |
Providing Internet Access to Computer in Workgroup | JR | Networking and the Internet with Windows XP | 0 | July 26th 04 10:14 PM |
Providing Internet Access to Computer in Workgroup | JR | Networking and the Internet with Windows XP | 0 | July 26th 04 10:14 PM |