If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
printing issues with Epson stylus C88+
i have a printer (see above) and WinXP... it will not print my documents. it
brand new... this yr 2/2007 bought it. it was printing, then it stopped. it may or may not print a full page... but most of the time it starts it.. prints 3 lines and then shots out all the paper... afterwards.. it just shots out blank pages; or cramp on it printed like (kdadkk kd========kdfakdakd )... I have email all my school/class work; even personal stuff to work and print it there..... or put on jump drive and drive copy center. HELP.... someone said that it could be a conflict with the winxp update driver thing and the epson driver.... but I can not / have not be able to fix it. HELP -- rosa m soto |
Ads |
#2
|
|||
|
|||
printing issues with Epson stylus C88+
rosie wrote:
i have a printer (see above) and WinXP... it will not print my documents. it brand new... this yr 2/2007 bought it. it was printing, then it stopped. it may or may not print a full page... but most of the time it starts it.. prints 3 lines and then shots out all the paper... afterwards.. it just shots out blank pages; or cramp on it printed like (kdadkk kd========kdfakdakd )... I have email all my school/class work; even personal stuff to work and print it there..... or put on jump drive and drive copy center. HELP.... someone said that it could be a conflict with the winxp update driver thing and the epson driver.... but I can not / have not be able to fix it. HELP -- rosa m soto The garbage output and feeding blank pages is often a symprom of a corrupt driver. Uninstall the printer using the uninstaller supplied by Epson. This should be in START, ALL PROGRAMS and look under Epson. Run the uninstaller. Now open Control Panel and open Printers and Faxes. Select File/Server Properties/Drivers select the driver that refers to the Epson Stylus C88 and click on Remove. Disconnect the cable that is attached to the printer. Reboot the PC and reinstall the printer using the disk that came with it or you can see if there is a later driver on the Epson website. Do not connect the cable to the printer until asked to do so. Good Luck. Tony MS MVP Printing/Imaging |
#3
|
|||
|
|||
printing issues with Epson stylus C88+
i had to wait til i was at work, so i could print these instructions... will
attempt it tonight and get back to you tomorrow thank you for the advice. will try tonight happy new years -- rosa m soto "Tony" wrote: rosie wrote: i have a printer (see above) and WinXP... it will not print my documents. it brand new... this yr 2/2007 bought it. it was printing, then it stopped. it may or may not print a full page... but most of the time it starts it.. prints 3 lines and then shots out all the paper... afterwards.. it just shots out blank pages; or cramp on it printed like (kdadkk kd========kdfakdakd )... I have email all my school/class work; even personal stuff to work and print it there..... or put on jump drive and drive copy center. HELP.... someone said that it could be a conflict with the winxp update driver thing and the epson driver.... but I can not / have not be able to fix it. HELP -- rosa m soto The garbage output and feeding blank pages is often a symprom of a corrupt driver. Uninstall the printer using the uninstaller supplied by Epson. This should be in START, ALL PROGRAMS and look under Epson. Run the uninstaller. Now open Control Panel and open Printers and Faxes. Select File/Server Properties/Drivers select the driver that refers to the Epson Stylus C88 and click on Remove. Disconnect the cable that is attached to the printer. Reboot the PC and reinstall the printer using the disk that came with it or you can see if there is a later driver on the Epson website. Do not connect the cable to the printer until asked to do so. Good Luck. Tony MS MVP Printing/Imaging |
#4
|
|||
|
|||
printing issues with Epson stylus C88+
I am having trouble with my printer, I have a Dell all-in-one Printer A940,
Ijust recently replaced the ink after being without it for several months, I know that I installed it correctly, and that everything is connected properly, but for some reason, it won't print, just blank pages come out. I have tried everything in the help and support section, at one point it said to click 'investigate' to see if my printer was connected to the right port, and the message I got was that it may be a corrupt driver and that I should uninstall the port and then reinstall it. I'm not sure how to do this. Could someone help please- Thanks, Vicki -- vickiee2 "rosie" wrote: i had to wait til i was at work, so i could print these instructions... will attempt it tonight and get back to you tomorrow thank you for the advice. will try tonight happy new years -- rosa m soto "Tony" wrote: rosie wrote: i have a printer (see above) and WinXP... it will not print my documents. it brand new... this yr 2/2007 bought it. it was printing, then it stopped. it may or may not print a full page... but most of the time it starts it.. prints 3 lines and then shots out all the paper... afterwards.. it just shots out blank pages; or cramp on it printed like (kdadkk kd========kdfakdakd )... I have email all my school/class work; even personal stuff to work and print it there..... or put on jump drive and drive copy center. HELP.... someone said that it could be a conflict with the winxp update driver thing and the epson driver.... but I can not / have not be able to fix it. HELP -- rosa m soto The garbage output and feeding blank pages is often a symprom of a corrupt driver. Uninstall the printer using the uninstaller supplied by Epson. This should be in START, ALL PROGRAMS and look under Epson. Run the uninstaller. Now open Control Panel and open Printers and Faxes. Select File/Server Properties/Drivers select the driver that refers to the Epson Stylus C88 and click on Remove. Disconnect the cable that is attached to the printer. Reboot the PC and reinstall the printer using the disk that came with it or you can see if there is a later driver on the Epson website. Do not connect the cable to the printer until asked to do so. Good Luck. Tony MS MVP Printing/Imaging |
Thread Tools | |
Display Modes | |
|
|