If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Unable to change netowrk settings with out disabling the connection first
I have a small network set-up at home. Decied to rebuild
my main pc as it was getting slow. I put my ghost backup image down onto the machine. I then configured back some missing software as well as the conneciton to my Server 2003 active directory domain. I was at first able to change the network settings for the card (SMC 1211). I am now however unable to change the settings with out first disabling the conecction. The user account does have admin rights so should be able to change thse setting no problems. Iam unable to find out what is wrong I can however see and netowrk drives on my domain but not able to get access to the internet. I use zone alarm pro 4.5 and have not changed anything on this. since the pc was rebuilt and since the pc has the same ip inof as the old build it should work fine but currently does not. Any help would be greatly recived. Adrian (IT engineer) |
Ads |
#2
|
|||
|
|||
Unable to change netowrk settings with out disabling the connection first
What happens when you try and change the settings?
-- Ken Wickes [MSFT] This posting is provided "AS IS" with no warranties, and confers no rights. "Adrian" wrote in message ... I have a small network set-up at home. Decied to rebuild my main pc as it was getting slow. I put my ghost backup image down onto the machine. I then configured back some missing software as well as the conneciton to my Server 2003 active directory domain. I was at first able to change the network settings for the card (SMC 1211). I am now however unable to change the settings with out first disabling the conecction. The user account does have admin rights so should be able to change thse setting no problems. Iam unable to find out what is wrong I can however see and netowrk drives on my domain but not able to get access to the internet. I use zone alarm pro 4.5 and have not changed anything on this. since the pc was rebuilt and since the pc has the same ip inof as the old build it should work fine but currently does not. Any help would be greatly recived. Adrian (IT engineer) |
#3
|
|||
|
|||
Unable to change netowrk settings with out disabling the connection first
What happens when you try and change the settings?
-- Ken Wickes [MSFT] This posting is provided "AS IS" with no warranties, and confers no rights. "Adrian" wrote in message ... I have a small network set-up at home. Decied to rebuild my main pc as it was getting slow. I put my ghost backup image down onto the machine. I then configured back some missing software as well as the conneciton to my Server 2003 active directory domain. I was at first able to change the network settings for the card (SMC 1211). I am now however unable to change the settings with out first disabling the conecction. The user account does have admin rights so should be able to change thse setting no problems. Iam unable to find out what is wrong I can however see and netowrk drives on my domain but not able to get access to the internet. I use zone alarm pro 4.5 and have not changed anything on this. since the pc was rebuilt and since the pc has the same ip inof as the old build it should work fine but currently does not. Any help would be greatly recived. Adrian (IT engineer) |
#4
|
|||
|
|||
Unable to change netowrk settings with out disabling the connection first
Nothing it sill does not work. Evey web page I go to
still errors. Since this is using the same setup as the old one and with the same ip. I do not seem to beale to understand what is causing the problme. Zone Alarm should not need to be changed as far as it is concerned it just the same as the pc. -----Original Message----- What happens when you try and change the settings? -- Ken Wickes [MSFT] This posting is provided "AS IS" with no warranties, and confers no rights. "Adrian" wrote in message ... I have a small network set-up at home. Decied to rebuild my main pc as it was getting slow. I put my ghost backup image down onto the machine. I then configured back some missing software as well as the conneciton to my Server 2003 active directory domain. I was at first able to change the network settings for the card (SMC 1211). I am now however unable to change the settings with out first disabling the conecction. The user account does have admin rights so should be able to change thse setting no problems. Iam unable to find out what is wrong I can however see and netowrk drives on my domain but not able to get access to the internet. I use zone alarm pro 4.5 and have not changed anything on this. since the pc was rebuilt and since the pc has the same ip inof as the old build it should work fine but currently does not. Any help would be greatly recived. Adrian (IT engineer) . |
#5
|
|||
|
|||
Unable to change netowrk settings with out disabling the connection first
Nothing it sill does not work. Evey web page I go to
still errors. Since this is using the same setup as the old one and with the same ip. I do not seem to beale to understand what is causing the problme. Zone Alarm should not need to be changed as far as it is concerned it just the same as the pc. -----Original Message----- What happens when you try and change the settings? -- Ken Wickes [MSFT] This posting is provided "AS IS" with no warranties, and confers no rights. "Adrian" wrote in message ... I have a small network set-up at home. Decied to rebuild my main pc as it was getting slow. I put my ghost backup image down onto the machine. I then configured back some missing software as well as the conneciton to my Server 2003 active directory domain. I was at first able to change the network settings for the card (SMC 1211). I am now however unable to change the settings with out first disabling the conecction. The user account does have admin rights so should be able to change thse setting no problems. Iam unable to find out what is wrong I can however see and netowrk drives on my domain but not able to get access to the internet. I use zone alarm pro 4.5 and have not changed anything on this. since the pc was rebuilt and since the pc has the same ip inof as the old build it should work fine but currently does not. Any help would be greatly recived. Adrian (IT engineer) . |
#6
|
|||
|
|||
Unable to change netowrk settings with out disabling the connection first
Nothing it sill does not work. Evey web page I go to
still errors. Since this is using the same setup as the old one and with the same ip. I do not seem to beale to understand what is causing the problme. Zone Alarm should not need to be changed as far as it is concerned it just the same as the pc. -----Original Message----- What happens when you try and change the settings? -- Ken Wickes [MSFT] This posting is provided "AS IS" with no warranties, and confers no rights. "Adrian" wrote in message ... I have a small network set-up at home. Decied to rebuild my main pc as it was getting slow. I put my ghost backup image down onto the machine. I then configured back some missing software as well as the conneciton to my Server 2003 active directory domain. I was at first able to change the network settings for the card (SMC 1211). I am now however unable to change the settings with out first disabling the conecction. The user account does have admin rights so should be able to change thse setting no problems. Iam unable to find out what is wrong I can however see and netowrk drives on my domain but not able to get access to the internet. I use zone alarm pro 4.5 and have not changed anything on this. since the pc was rebuilt and since the pc has the same ip inof as the old build it should work fine but currently does not. Any help would be greatly recived. Adrian (IT engineer) . |
#7
|
|||
|
|||
Unable to change netowrk settings with out disabling the connection first
Nothing it sill does not work. Evey web page I go to
still errors. Since this is using the same setup as the old one and with the same ip. I do not seem to beale to understand what is causing the problme. Zone Alarm should not need to be changed as far as it is concerned it just the same as the pc. -----Original Message----- What happens when you try and change the settings? -- Ken Wickes [MSFT] This posting is provided "AS IS" with no warranties, and confers no rights. "Adrian" wrote in message ... I have a small network set-up at home. Decied to rebuild my main pc as it was getting slow. I put my ghost backup image down onto the machine. I then configured back some missing software as well as the conneciton to my Server 2003 active directory domain. I was at first able to change the network settings for the card (SMC 1211). I am now however unable to change the settings with out first disabling the conecction. The user account does have admin rights so should be able to change thse setting no problems. Iam unable to find out what is wrong I can however see and netowrk drives on my domain but not able to get access to the internet. I use zone alarm pro 4.5 and have not changed anything on this. since the pc was rebuilt and since the pc has the same ip inof as the old build it should work fine but currently does not. Any help would be greatly recived. Adrian (IT engineer) . |
#8
|
|||
|
|||
Unable to change netowrk settings with out disabling the connection first
More details would be good. Also temporarily uninstalling ZoneAlarm would
be a good step. -- Ken Wickes [MSFT] This posting is provided "AS IS" with no warranties, and confers no rights. "adrian" wrote in message ... Nothing it sill does not work. Evey web page I go to still errors. Since this is using the same setup as the old one and with the same ip. I do not seem to beale to understand what is causing the problme. Zone Alarm should not need to be changed as far as it is concerned it just the same as the pc. -----Original Message----- What happens when you try and change the settings? -- Ken Wickes [MSFT] This posting is provided "AS IS" with no warranties, and confers no rights. "Adrian" wrote in message ... I have a small network set-up at home. Decied to rebuild my main pc as it was getting slow. I put my ghost backup image down onto the machine. I then configured back some missing software as well as the conneciton to my Server 2003 active directory domain. I was at first able to change the network settings for the card (SMC 1211). I am now however unable to change the settings with out first disabling the conecction. The user account does have admin rights so should be able to change thse setting no problems. Iam unable to find out what is wrong I can however see and netowrk drives on my domain but not able to get access to the internet. I use zone alarm pro 4.5 and have not changed anything on this. since the pc was rebuilt and since the pc has the same ip inof as the old build it should work fine but currently does not. Any help would be greatly recived. Adrian (IT engineer) . |
#9
|
|||
|
|||
Unable to change netowrk settings with out disabling the connection first
More details would be good. Also temporarily uninstalling ZoneAlarm would
be a good step. -- Ken Wickes [MSFT] This posting is provided "AS IS" with no warranties, and confers no rights. "adrian" wrote in message ... Nothing it sill does not work. Evey web page I go to still errors. Since this is using the same setup as the old one and with the same ip. I do not seem to beale to understand what is causing the problme. Zone Alarm should not need to be changed as far as it is concerned it just the same as the pc. -----Original Message----- What happens when you try and change the settings? -- Ken Wickes [MSFT] This posting is provided "AS IS" with no warranties, and confers no rights. "Adrian" wrote in message ... I have a small network set-up at home. Decied to rebuild my main pc as it was getting slow. I put my ghost backup image down onto the machine. I then configured back some missing software as well as the conneciton to my Server 2003 active directory domain. I was at first able to change the network settings for the card (SMC 1211). I am now however unable to change the settings with out first disabling the conecction. The user account does have admin rights so should be able to change thse setting no problems. Iam unable to find out what is wrong I can however see and netowrk drives on my domain but not able to get access to the internet. I use zone alarm pro 4.5 and have not changed anything on this. since the pc was rebuilt and since the pc has the same ip inof as the old build it should work fine but currently does not. Any help would be greatly recived. Adrian (IT engineer) . |
Thread Tools | |
Display Modes | |
|
|