recogniWindows XP will notze my CDRom drive

To Jerry-- The mother board is fairly new, it is of a cheap make though
its a AsRock P4S55FX Every thing else seems to be reading fine, I dont
think its the battery

To namniar-- Im not sure what You mean by jumper settings, sense I dont
know what they are this very well could be the problem please supply me
with a little more information.

To ALL-- Below is the message I get while booting up with the Cdrom
drive hooked up

Auto-Detecting Pri Master - IDE Hard Disk
Auto-Detecting Pri Slave - Not detected.....
Auto-Detecting Secondary MAster - Not detected.....
Auto-Detecting Secondary Slave - ATAPI CDROM

Pri Master A93 0500 Maxtor 6104052 Ultra DMA mode - 6, S.M.A.R.T
capable but disabled

Secondary Slave 0527 - TOSHIBA CD-ROM XM-6002B

!!!!!! IDE DRIVES INSTALLATION ERROR !!!!!!!
For best reliability & performance, please change the stand alone slave
drive to master SYSTEM HALT.........

once again thank you all very much for your feedback


--
TriForce
------------------------------------------------------------------------
TriForce's Profile: http://extremetechsupport.com/forum/...tml?userid=676
View this thread: http://extremetechsupport.com/forum/...phtml?t=136543

Okay, from your description in this and your last post, your first issue is
with jumper settings.

As I understand it you have 1 harddrive on the primary IDE channel and 1
cd-rom on the secondary IDE channel. Is that correct? I bet it also takes
about a minute to get through the initial POST screen whereas it should be
about 1-2 seconds.

Assuming the above:

Set the jumper on the harddrive to Single Master. It is likely set to Dual
Master right now.

Set the jumper on the cd-rom to Master or if available Single Master.

For more info on harddrive visit support at
http://www.maxtor.com/

For Cd-rom click on "manual" on the right side and scroll down to jumper
settings
http://www.toshiba-europe.com/storag...&model=XM6002B

r.

Please continue the original post next time instead of creating a new post
on the same problem so others can follow the thread.


"TriForce" wrote in message
...

To Jerry-- The mother board is fairly new, it is of a cheap make though
its a AsRock P4S55FX Every thing else seems to be reading fine, I dont
think its the battery

To namniar-- Im not sure what You mean by jumper settings, sense I dont
know what they are this very well could be the problem please supply me
with a little more information.

To ALL-- Below is the message I get while booting up with the Cdrom
drive hooked up

Auto-Detecting Pri Master - IDE Hard Disk
Auto-Detecting Pri Slave - Not detected.....
Auto-Detecting Secondary MAster - Not detected.....
Auto-Detecting Secondary Slave - ATAPI CDROM

Pri Master A93 0500 Maxtor 6104052 Ultra DMA mode - 6, S.M.A.R.T
capable but disabled

Secondary Slave 0527 - TOSHIBA CD-ROM XM-6002B

!!!!!! IDE DRIVES INSTALLATION ERROR !!!!!!!
For best reliability & performance, please change the stand alone slave
drive to master SYSTEM HALT.........

once again thank you all very much for your feedback


--
TriForce
------------------------------------------------------------------------
TriForce's Profile:
http://extremetechsupport.com/forum/...tml?userid=676
View this thread:
http://extremetechsupport.com/forum/...phtml?t=136543

You mentioned code 41 in your previous post....

http://support.microsoft.com/default...b;en-us;314060

r.

"TriForce" wrote in message
...

To Jerry-- The mother board is fairly new, it is of a cheap make though
its a AsRock P4S55FX Every thing else seems to be reading fine, I dont
think its the battery

To namniar-- Im not sure what You mean by jumper settings, sense I dont
know what they are this very well could be the problem please supply me
with a little more information.

To ALL-- Below is the message I get while booting up with the Cdrom
drive hooked up

Auto-Detecting Pri Master - IDE Hard Disk
Auto-Detecting Pri Slave - Not detected.....
Auto-Detecting Secondary MAster - Not detected.....
Auto-Detecting Secondary Slave - ATAPI CDROM

Pri Master A93 0500 Maxtor 6104052 Ultra DMA mode - 6, S.M.A.R.T
capable but disabled

Secondary Slave 0527 - TOSHIBA CD-ROM XM-6002B

!!!!!! IDE DRIVES INSTALLATION ERROR !!!!!!!
For best reliability & performance, please change the stand alone slave
drive to master SYSTEM HALT.........

once again thank you all very much for your feedback


--
TriForce
------------------------------------------------------------------------
TriForce's Profile:
http://extremetechsupport.com/forum/...tml?userid=676
View this thread:
http://extremetechsupport.com/forum/...phtml?t=136543