If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#16
|
|||
|
|||
Is there some software to save drivers to disk?
On Sat, 01 Mar 2014 13:54:47 -0500, Paul wrote:
Ken Blake, MVP wrote: Out of curiosity, I just looked at Amazon.com. You can buy a 40GB IDE drive for $11.11 and an 80GB one for $19. Why struggle with a 6GB drive? Did you see the words "refurb" or "pull" next to those advertisements ? No. Those drives could have been used for 10,000 hours already, and sound like a bag of ball bearings :-) They may have been parted-out, of some lease returns. They are new. Or at least Amazon says so, and I have always found Amazon to be honest. A "real" drive, should cost $50 or more. $11 would not cover the cost of the electronics on the controller board, when an appropriate markup was added. So those drives were acquired for nothing, by their current seller. Refurb or pull is my guess. My guess is that they are new, but old stock that isn't selling. Regardless of much it cost to make them, few people want such small drives, so prices are lowered dramatically to get rid of them. |
Ads |
#17
|
|||
|
|||
Is there some software to save drivers to disk?
On Sat, 01 Mar 2014 12:05:59 -0700, "Ken Blake, MVP"
wrote: On Sat, 01 Mar 2014 13:54:47 -0500, Paul wrote: Ken Blake, MVP wrote: Out of curiosity, I just looked at Amazon.com. You can buy a 40GB IDE drive for $11.11 and an 80GB one for $19. Why struggle with a 6GB drive? Did you see the words "refurb" or "pull" next to those advertisements ? No. Those drives could have been used for 10,000 hours already, and sound like a bag of ball bearings :-) They may have been parted-out, of some lease returns. They are new. Or at least Amazon says so, and I have always found Amazon to be honest. A "real" drive, should cost $50 or more. $11 would not cover the cost of the electronics on the controller board, when an appropriate markup was added. So those drives were acquired for nothing, by their current seller. Refurb or pull is my guess. My guess is that they are new, but old stock that isn't selling. Regardless of much it cost to make them, few people want such small drives, so prices are lowered dramatically to get rid of them. And by the way, Amazon also offers both of those drives used--$4.49 for the 80GB, and $3.48 for the 40GB. |
#18
|
|||
|
|||
Is there some software to save drivers to disk?
J. P. Gilliver (John) wrote:
Paul has suggested some possible ways of finding bigger ones that might work. Certainly go for as much as will - 512M _might_ be OK for SP2. (I've also heard of people using USB RAM, though I've also heard it said that the way Windows uses RAM means that some kinds of USB RAM when used in this way have a life measured in hours.) Actually, you could put a pagefile on a gigabyte RAMDisk, if the computer would not hold more memory. But this is hardly practical. With a high-bandwidth storage device for pagefile, WinXP is pretty smooth. I've had 5GB worth of programs running on a WinXP 32 bit Sp3 machine, by having a pagefile mounted on a 4GB/sec storage device. The programs are swapped in, when you shift the focus to the next program. And compared to paging from a hard drive, the result was pretty impressive. Only a slight delay or sluggishness was evident. Not the 30 second delay you might see from a hard drive, grinding away. And more virtual memory was in play, than Windows 32 bit can normally address (because paging makes the difference). This is the Gigabyte one that fits in a PC slot. You can't get these any more, and I bet people reselling these, probably charge a pretty penny for them. Then, there's the detail of how the pagefile gets on the disk, so it's ready at startup. The PCI bus limits the bandwidth, but the seek time is "zero". Beats the pants off a hard drive, for random access. Even if it could only sustain 110MB/sec. http://www.newegg.com/Product/Produc...82E16815168001 The other one you can get, connects to a SATA port. You can probably find some benchmarks somewhere for these. http://www.acard.com.tw/english/newstabpop.jsp?idno=93 Those are all silly ideas, because the price of the solution is probably more than the entire PC is worth. The solutions are noteworthy, in that the storage media (Dynamic RAM, DDR2 on the second one), doesn't wear out. You can get business versions of those, with PCI Express connectors, but those probably start at around $10,000 a piece. And a separate box sits outside the computer. ******* In my view, 512MB is barely adequate. I built and ran a PC like that for a short time, but I could only keep about 3 programs open at a time. If you only kept the one program open, then your options for what you run, might be a little more ambitious. But if you run three large programs, don't expect 512MB to go very far. Maybe some older version of Opera would use less RAM ? The latest Opera made a platform switch, so maybe some older version would be better. Paul |
#19
|
|||
|
|||
Is there some software to save drivers to disk?
Ken Blake, MVP wrote:
On Sat, 01 Mar 2014 12:05:59 -0700, "Ken Blake, MVP" wrote: On Sat, 01 Mar 2014 13:54:47 -0500, Paul wrote: Ken Blake, MVP wrote: Out of curiosity, I just looked at Amazon.com. You can buy a 40GB IDE drive for $11.11 and an 80GB one for $19. Why struggle with a 6GB drive? Did you see the words "refurb" or "pull" next to those advertisements ? No. Those drives could have been used for 10,000 hours already, and sound like a bag of ball bearings :-) They may have been parted-out, of some lease returns. They are new. Or at least Amazon says so, and I have always found Amazon to be honest. A "real" drive, should cost $50 or more. $11 would not cover the cost of the electronics on the controller board, when an appropriate markup was added. So those drives were acquired for nothing, by their current seller. Refurb or pull is my guess. My guess is that they are new, but old stock that isn't selling. Regardless of much it cost to make them, few people want such small drives, so prices are lowered dramatically to get rid of them. And by the way, Amazon also offers both of those drives used--$4.49 for the 80GB, and $3.48 for the 40GB. Did Amazon have customer reviews for the items ? I'm curious what the customers think of them. Paul |
#20
|
|||
|
|||
Is there some software to save drivers to disk?
In message , Paul
writes: J. P. Gilliver (John) wrote: Paul has suggested some possible ways of finding bigger ones that might work. Certainly go for as much as will - 512M _might_ be OK for SP2. (I've also heard of people using USB RAM, though I've also heard it said that the way Windows uses RAM means that some kinds of USB RAM when used in this way have a life measured in hours.) Actually, you could put a pagefile on a gigabyte RAMDisk, if the computer would not hold more memory. But this [] Those are all silly ideas, because the price of the solution is probably more than the entire PC is worth. The solutions are noteworthy, in that the storage media (Dynamic RAM, DDR2 on the second one), doesn't wear out. You can get [] You've got it! I'm really doing this as an intellectual/curiosity exercise only, not really a practical approach - I intend to spend no more money on it beyond the little I spent on some more RAM for it! In my view, 512MB is barely adequate. I built and ran a PC like that for a short time, but I could only keep about 3 programs open at a time. If you only kept the one program open, then your options for what you run, might be a little more ambitious. But if you run three large programs, don't expect 512MB to go very far. (It actually has 640 now.) One of the things that does puzzle me is how the previous owner managed to use it to do serious accountancy work: granted, she only did it for a friend's small company, but using heavyweight stuff like Sage accounting, and she had the CDs from HMRC (UK equivalent of IRS) loaded. And that was with only 256M. I guess she must have been very disciplined about doing only one thing at a time. (She also had AOL's broadband software - the old one that took over _everything_. But then her broadband line operated at about 128k - yes really, she's rural and unlucky [her neighbour over the road got 1.5M] - so I think she only really used it for email, no web.) Maybe some older version of Opera would use less RAM ? The latest Opera made a platform switch, so maybe some older version would be better. I thought Opera was payware? I admit I haven't looked at it for many years. Paul -- J. P. Gilliver. UMRA: 1960/1985 MB++G()AL-IS-Ch++(p)Ar@T+H+Sh0!:`)DNAf "Does Barbie come with Ken?" "Barbie comes with G.I. Joe. She fakes it with Ken." - anonymous |
#21
|
|||
|
|||
Is there some software to save drivers to disk?
In message , "Ken Blake,
MVP" writes: [] Out of curiosity, I just looked at Amazon.com. You can buy a 40GB IDE drive for $11.11 and an 80GB one for $19. Why struggle with a 6GB drive? See my longer reply to Paul - really just intellectual curiosity, to see if it _can_ be made into a usable machine. Out of curiosity, what's the smallest footprint anyone knows of that's still recognisably XP? I know the 98lite people (now called something like PClite) claimed to have a version of 98 in IIRR 90M, or even 50M for embedded applications, though I don't know how recognisably 98 those are. -- J. P. Gilliver. UMRA: 1960/1985 MB++G()AL-IS-Ch++(p)Ar@T+H+Sh0!:`)DNAf The truth is, almost everyone in the world is lovely. But the world is ruined for us by the sociopaths and those who aren't lovely. - Richard Osman to Alison Graham, in Radio Times 2013-6-8 to 14 |
#22
|
|||
|
|||
Is there some software to save drivers to disk?
On Sun, 2 Mar 2014 10:53:50 +0000, "J. P. Gilliver (John)"
wrote: In message , "Ken Blake, MVP" writes: [] Out of curiosity, I just looked at Amazon.com. You can buy a 40GB IDE drive for $11.11 and an 80GB one for $19. Why struggle with a 6GB drive? See my longer reply to Paul - really just intellectual curiosity, to see if it _can_ be made into a usable machine. OK. I wouldn't bother with something like that, but we're all different. |
#23
|
|||
|
|||
Is there some software to save drivers to disk?
On Sat, 01 Mar 2014 15:14:29 -0500, Paul wrote:
Ken Blake, MVP wrote: On Sat, 01 Mar 2014 12:05:59 -0700, "Ken Blake, MVP" wrote: On Sat, 01 Mar 2014 13:54:47 -0500, Paul wrote: Ken Blake, MVP wrote: Out of curiosity, I just looked at Amazon.com. You can buy a 40GB IDE drive for $11.11 and an 80GB one for $19. Why struggle with a 6GB drive? Did you see the words "refurb" or "pull" next to those advertisements ? No. Those drives could have been used for 10,000 hours already, and sound like a bag of ball bearings :-) They may have been parted-out, of some lease returns. They are new. Or at least Amazon says so, and I have always found Amazon to be honest. A "real" drive, should cost $50 or more. $11 would not cover the cost of the electronics on the controller board, when an appropriate markup was added. So those drives were acquired for nothing, by their current seller. Refurb or pull is my guess. My guess is that they are new, but old stock that isn't selling. Regardless of much it cost to make them, few people want such small drives, so prices are lowered dramatically to get rid of them. And by the way, Amazon also offers both of those drives used--$4.49 for the 80GB, and $3.48 for the 40GB. Did Amazon have customer reviews for the items ? I'm curious what the customers think of them. I went back to the site to check, because I was also curious. But you could have done it yourself. The $11.11 40 GB 2 gave it 5 stars 2 gave it 4 stars 0 gave it 3 0 gave it 2 0 gave it 1 The $19 80GB 30 gave it 5 stars 15 gave it 4 5 gave it 3 7 gave it 2 18 gave it 0 There were also written reviews. Three liked it, 5 said it was obviously used, despite the way it was advertised. |
#24
|
|||
|
|||
Is there some software to save drivers to disk?
J. P. Gilliver (John) wrote:
In message , Paul writes: J. P. Gilliver (John) wrote: Paul has suggested some possible ways of finding bigger ones that might work. Certainly go for as much as will - 512M _might_ be OK for SP2. (I've also heard of people using USB RAM, though I've also heard it said that the way Windows uses RAM means that some kinds of USB RAM when used in this way have a life measured in hours.) Actually, you could put a pagefile on a gigabyte RAMDisk, if the computer would not hold more memory. But this [] Those are all silly ideas, because the price of the solution is probably more than the entire PC is worth. The solutions are noteworthy, in that the storage media (Dynamic RAM, DDR2 on the second one), doesn't wear out. You can get [] You've got it! I'm really doing this as an intellectual/curiosity exercise only, not really a practical approach - I intend to spend no more money on it beyond the little I spent on some more RAM for it! In my view, 512MB is barely adequate. I built and ran a PC like that for a short time, but I could only keep about 3 programs open at a time. If you only kept the one program open, then your options for what you run, might be a little more ambitious. But if you run three large programs, don't expect 512MB to go very far. (It actually has 640 now.) One of the things that does puzzle me is how the previous owner managed to use it to do serious accountancy work: granted, she only did it for a friend's small company, but using heavyweight stuff like Sage accounting, and she had the CDs from HMRC (UK equivalent of IRS) loaded. And that was with only 256M. I guess she must have been very disciplined about doing only one thing at a time. (She also had AOL's broadband software - the old one that took over _everything_. But then her broadband line operated at about 128k - yes really, she's rural and unlucky [her neighbour over the road got 1.5M] - so I think she only really used it for email, no web.) Maybe some older version of Opera would use less RAM ? The latest Opera made a platform switch, so maybe some older version would be better. I thought Opera was payware? I admit I haven't looked at it for many years. Paul 128K could be ISDN. That data rate you mention, just happens to be a "magic value", and matches ISDN BRI. 128K would be a weird choice for ADSL. The one in red color here is a 1.5Mbit/sec service (suitably hobbled by it's operational cap). The reach curve just doesn't go far enough, to make a crappy rate like that worthwhile - it doesn't add much to the distance. Maybe the telco made an arbitrary decision, that people on one side of the road were "within reach", and people on the other side of the road were not. In some cases, it's an artificial distinction, about which service area is handled by which telco CO building. http://www.internode.on.net/resident...d/performance/ ******* The last time I downloaded Opera, it was free. Paul |
#25
|
|||
|
|||
Is there some software to save drivers to disk?
In message , Paul
writes: [] thing at a time. (She also had AOL's broadband software - the old one that took over _everything_. But then her broadband line operated at about 128k - yes really, she's rural and unlucky [her neighbour over the road got 1.5M] - so I think she only really used it for email, no [] 128K could be ISDN. That data rate you mention, just happens to be a "magic value", and matches ISDN BRI. No, it _was_ nominally ADSL - just a poor line. Or rather limited: I can't remember the details now, but I remember trying faster speeds (I don't remember why, but it wasn't adaptive), and it worked erratically; at the 128K, it was rock solid (just painfully slow!). [] The last time I downloaded Opera, it was free. [] Ah, useful to know, thanks. Back to that ancient system: I now have it running rather smoothly! But the HD _is_ rather small. If I _did_ want to give it a bigger one: I quickly googled this afternoon, and everyone seemed to talk about "cloning". _Does_ "cloning" (e. g., EaseUS ToDo) do more than just copy all the files over? I do realise it's necessary if you start from the PC on which the source OS is _running_, but if done from a different PC, is there more than just a copy going on? -- J. P. Gilliver. UMRA: 1960/1985 MB++G()AL-IS-Ch++(p)Ar@T+H+Sh0!:`)DNAf - often six furlongs ahead of the field, but on the wrong racecourse. - Colin Dexter on (his creation the character) Morse; Radio Times 12-18 May 2012. |
#26
|
|||
|
|||
Is there some software to save drivers to disk?
J. P. Gilliver (John) wrote:
In message , Paul writes: [] thing at a time. (She also had AOL's broadband software - the old one that took over _everything_. But then her broadband line operated at about 128k - yes really, she's rural and unlucky [her neighbour over the road got 1.5M] - so I think she only really used it for email, no [] 128K could be ISDN. That data rate you mention, just happens to be a "magic value", and matches ISDN BRI. No, it _was_ nominally ADSL - just a poor line. Or rather limited: I can't remember the details now, but I remember trying faster speeds (I don't remember why, but it wasn't adaptive), and it worked erratically; at the 128K, it was rock solid (just painfully slow!). [] The last time I downloaded Opera, it was free. [] Ah, useful to know, thanks. Back to that ancient system: I now have it running rather smoothly! But the HD _is_ rather small. If I _did_ want to give it a bigger one: I quickly googled this afternoon, and everyone seemed to talk about "cloning". _Does_ "cloning" (e. g., EaseUS ToDo) do more than just copy all the files over? I do realise it's necessary if you start from the PC on which the source OS is _running_, but if done from a different PC, is there more than just a copy going on? With things like so-called "Smart Copy", only the sectors containing data the file system needs, would be copied. The copy operation would copy the MBR (Sector 0), it would analyse each partition and figure out what sectors need to be copied. This saves time, when the source disk is not full. In addition to that method, there is also a "dumb" sector copy method, which just copies ever sector. The advantage of such a method, is your cloning utility won't get confused, if the partitions are XFS or FreeBSD or HFS+ or something. You can handle any kind of partition, with a dumb method. The "dd" utility ported to Windows, can do that for you. You use a dual boot system (so the OS to be copied is not running), to do such a copy. The "dd" program doesn't call VSS to make the open files quiescent. So the user has to arrange the OS partition, to not be in use for that kind of copy to work. Macrium Reflect Free can clone the drive with the OS on it, using the program as installed on that OS. In addition, the Macrium Reflect Rescue CD can also do cloning, and then you know the OS is not running, and all files would be copied intact. There are a ton of utilities like Easeus that could do the job for you. Even Seagate and Western Digital, provide a version of Acronis TIH for their customers. And if you can wade through the manual, there's likely a cloning equivalent in there. When you're finished cloning an OS drive, shut down and disconnect the clone, until you're ready to use it. The clone should be booted by itself the first time (should not be able to "see" the source disk). After the clone drive has booted at least once, it is then safe to re-connect the source drive and do whatever you like. I forgot to do this once, and the OS drive letter gets screwed up, as if the pagefile on the source disk is being used and the original disk is still C: . Leading to confusion as the clone disk attempts to boot. I couldn't really debug what was going on, and that's just a guess. I re-cloned, and tried again, and by remembering to disconnect the source disk, it managed a proper boot cycle. Paul |
#27
|
|||
|
|||
Is there some software to save drivers to disk?
In message , Paul
writes: J. P. Gilliver (John) wrote: [] Back to that ancient system: I now have it running rather smoothly! But the HD _is_ rather small. If I _did_ want to give it a bigger one: I quickly googled this afternoon, and everyone seemed to talk about "cloning". _Does_ "cloning" (e. g., EaseUS ToDo) do more than just copy all the files over? I do realise it's necessary if you start from the PC on which the source OS is _running_, but if done from a different PC, is there more than just a copy going on? With things like so-called "Smart Copy", only the sectors containing data the file system needs, would be copied. The copy operation would copy the MBR (Sector 0), it would analyse each partition and figure out what sectors need to be copied. This saves time, when the source disk is not full. Wouldn't just copying the files do that anyway? [rest of _very_ detailed reply snipped] What I'm asking is: does "cloning" do more than just copy files - or, rather, assuming a source and destination drive both formatted (let's say as a single NTFS partition), would just copying all the files/folders from one HD to another (using a separate computer) result in a bootable system, or are there arcane magics involving active sectors, MBRs, and so on involved? -- J. P. Gilliver. UMRA: 1960/1985 MB++G()AL-IS-Ch++(p)Ar@T+H+Sh0!:`)DNAf "What did I do to deserve this?" "How long a list would you like?"- Vila & Avon |
#28
|
|||
|
|||
Is there some software to save drivers to disk?
J. P. Gilliver (John) wrote:
In message , Paul writes: J. P. Gilliver (John) wrote: [] Back to that ancient system: I now have it running rather smoothly! But the HD _is_ rather small. If I _did_ want to give it a bigger one: I quickly googled this afternoon, and everyone seemed to talk about "cloning". _Does_ "cloning" (e. g., EaseUS ToDo) do more than just copy all the files over? I do realise it's necessary if you start from the PC on which the source OS is _running_, but if done from a different PC, is there more than just a copy going on? With things like so-called "Smart Copy", only the sectors containing data the file system needs, would be copied. The copy operation would copy the MBR (Sector 0), it would analyse each partition and figure out what sectors need to be copied. This saves time, when the source disk is not full. Wouldn't just copying the files do that anyway? [rest of _very_ detailed reply snipped] What I'm asking is: does "cloning" do more than just copy files - or, rather, assuming a source and destination drive both formatted (let's say as a single NTFS partition), would just copying all the files/folders from one HD to another (using a separate computer) result in a bootable system, or are there arcane magics involving active sectors, MBRs, and so on involved? I refuse to be drawn into an attempt to define "copy" and "clone" :-) Clone, as implemented with the suggested tools, copies every sector which has anything to do with the partition. The file system header, the metadata files ($MFT etc), the actual files and directories, any sector which the file system knows has something to do with that file system, is copied. That's a lot more than just the files themselves (as you'd get with Robocopy). Now, whether that's important or not, is debatable. I can tell you, if I prepare a new partition, and intend to copy an OS over to it, I will need to do "fixboot" later. That loads some sectors in the file system header area. If I use cloning software, that stuff would be copied for free. If I Robocopy over a set of OS files, I will need to run "fixboot" separately. Cloning just takes care of a bunch of details like that for you. That's actually how I defragment my WinXP partition. Rather than wait more than eight hours for the defragmenter to do the job, I just copy all the files off with Robocopy, format the partition, copy the files back with Robocopy, boot the installer CD and do "fixboot" from there. Then, my nice clean OS is ready to be booted up. The reason I can do that, is the machine is dual boot, and I do the stated operations from a second Windows OS. (All except the "fixboot", which I do with the installer CD. I've never been able to find a version I could run from any running Windows. Just the recovery console.) Paul |
#29
|
|||
|
|||
Is there some software to save drivers to disk?
Paul wrote:
J. P. Gilliver (John) wrote: In message , Paul writes: J. P. Gilliver (John) wrote: [] Back to that ancient system: I now have it running rather smoothly! But the HD _is_ rather small. If I _did_ want to give it a bigger one: I quickly googled this afternoon, and everyone seemed to talk about "cloning". _Does_ "cloning" (e. g., EaseUS ToDo) do more than just copy all the files over? I do realise it's necessary if you start from the PC on which the source OS is _running_, but if done from a different PC, is there more than just a copy going on? With things like so-called "Smart Copy", only the sectors containing data the file system needs, would be copied. The copy operation would copy the MBR (Sector 0), it would analyse each partition and figure out what sectors need to be copied. This saves time, when the source disk is not full. Wouldn't just copying the files do that anyway? [rest of _very_ detailed reply snipped] What I'm asking is: does "cloning" do more than just copy files - or, rather, assuming a source and destination drive both formatted (let's say as a single NTFS partition), would just copying all the files/folders from one HD to another (using a separate computer) result in a bootable system, or are there arcane magics involving active sectors, MBRs, and so on involved? I refuse to be drawn into an attempt to define "copy" and "clone" :-) Clone, as implemented with the suggested tools, copies every sector which has anything to do with the partition. The file system header, the metadata files ($MFT etc), the actual files and directories, any sector which the file system knows has something to do with that file system, is copied. That's a lot more than just the files themselves (as you'd get with Robocopy). Now, whether that's important or not, is debatable. I can tell you, if I prepare a new partition, and intend to copy an OS over to it, I will need to do "fixboot" later. That loads some sectors in the file system header area. If I use cloning software, that stuff would be copied for free. If I Robocopy over a set of OS files, I will need to run "fixboot" separately. Cloning just takes care of a bunch of details like that for you. That's actually how I defragment my WinXP partition. Rather than wait more than eight hours for the defragmenter to do the job, I just copy all the files off with Robocopy, format the partition, copy the files back with Robocopy, boot the installer CD and do "fixboot" from there. Then, my nice clean OS is ready to be booted up. The reason I can do that, is the machine is dual boot, and I do the stated operations from a second Windows OS. (All except the "fixboot", which I do with the installer CD. I've never been able to find a version I could run from any running Windows. Just the recovery console.) Paul I think I have a simpler suggestion for you Paul, if you happen to have Acronis True Image or any partition copying program: Just make an image of C: and restore that. (I think that would be simpler and perhaps quicker, unless I've missed something, which is indeed possible). I do this C: system image/restore fair amount of time after testing out some new software, and want to restore my system to the exact pre-test condition. |
#30
|
|||
|
|||
Is there some software to save drivers to disk?
J. P. Gilliver (John) wrote:
In message , Paul writes: J. P. Gilliver (John) wrote: [] Back to that ancient system: I now have it running rather smoothly! But the HD _is_ rather small. If I _did_ want to give it a bigger one: I quickly googled this afternoon, and everyone seemed to talk about "cloning". _Does_ "cloning" (e. g., EaseUS ToDo) do more than just copy all the files over? I do realise it's necessary if you start from the PC on which the source OS is _running_, but if done from a different PC, is there more than just a copy going on? With things like so-called "Smart Copy", only the sectors containing data the file system needs, would be copied. The copy operation would copy the MBR (Sector 0), it would analyse each partition and figure out what sectors need to be copied. This saves time, when the source disk is not full. Wouldn't just copying the files do that anyway? [rest of _very_ detailed reply snipped] What I'm asking is: does "cloning" do more than just copy files - or, rather, assuming a source and destination drive both formatted (let's say as a single NTFS partition), would just copying all the files/folders from one HD to another (using a separate computer) result in a bootable system, or are there arcane magics involving active sectors, MBRs, and so on involved? And setting the partition flag to be Active, amongst maybe some other things. And maybe that's part (or all?) of what "fixboot" does (see Paul's response). |
Thread Tools | |
Display Modes | |
|
|