A Windows XP help forum. PCbanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » PCbanter forum » Microsoft Windows 7 » Windows 7 Forum
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Delayed Re-Boot?



 
 
Thread Tools Rate Thread Display Modes
  #1  
Old May 29th 13, 10:05 PM posted to alt.windows7.general
(PeteCresswell)
external usenet poster
 
Posts: 1,933
Default Delayed Re-Boot?

I have an IP cam hanging on a Windows 7 box about 80 miles from home.

Every so often, the cam goes brain-dead and the only way to get it back
is to cut power to the cam and then restore power - causing the cam to
do a cold start.

I thought I had it licked when I put in one of those power strips that
senses how much the PC is drawing and cuts power to everything else
plugged in to it when it senses that the PC is no longer drawing power
above a certain level.

The plan was to just TeamViewer into the PC and issue a manual re-boot
if/when the cam went South.

But that does not work. I am guessing that a re-boot does not reduce
the power consumption long enough to trip the power strip.

What I would like to do is somehow have the PC shut itself down and then
re-start at least 30 seconds later. The timing does not have to be
that exact... just so it actually powers off and stays that way for at
least a few seconds.... At 0200 in the morning, nobody's going to care
as long as the sys is back up by sunrise.

Can anybody point to a way to accomplish this without spending a lot of
money on something like a remote-controlled power strip?
--
Pete Cresswell
Ads
  #2  
Old May 29th 13, 11:42 PM posted to alt.windows7.general
Paul in Houston TX
external usenet poster
 
Posts: 744
Default Delayed Re-Boot?

(PeteCresswell) wrote:
I have an IP cam hanging on a Windows 7 box about 80 miles from home.

Every so often, the cam goes brain-dead and the only way to get it back
is to cut power to the cam and then restore power - causing the cam to
do a cold start.

I thought I had it licked when I put in one of those power strips that
senses how much the PC is drawing and cuts power to everything else
plugged in to it when it senses that the PC is no longer drawing power
above a certain level.

The plan was to just TeamViewer into the PC and issue a manual re-boot
if/when the cam went South.

But that does not work. I am guessing that a re-boot does not reduce
the power consumption long enough to trip the power strip.

What I would like to do is somehow have the PC shut itself down and then
re-start at least 30 seconds later. The timing does not have to be
that exact... just so it actually powers off and stays that way for at
least a few seconds.... At 0200 in the morning, nobody's going to care
as long as the sys is back up by sunrise.

Can anybody point to a way to accomplish this without spending a lot of
money on something like a remote-controlled power strip?


Timer? I have one of those old motor driven ones that
can turn something off then back on 15 minutes later.
Electronic versions have their own clock in case the
power goes off for a while.
  #3  
Old May 30th 13, 12:49 AM posted to alt.windows7.general
Paul
external usenet poster
 
Posts: 18,275
Default Delayed Re-Boot?

(PeteCresswell) wrote:
I have an IP cam hanging on a Windows 7 box about 80 miles from home.

Every so often, the cam goes brain-dead and the only way to get it back
is to cut power to the cam and then restore power - causing the cam to
do a cold start.

I thought I had it licked when I put in one of those power strips that
senses how much the PC is drawing and cuts power to everything else
plugged in to it when it senses that the PC is no longer drawing power
above a certain level.

The plan was to just TeamViewer into the PC and issue a manual re-boot
if/when the cam went South.

But that does not work. I am guessing that a re-boot does not reduce
the power consumption long enough to trip the power strip.

What I would like to do is somehow have the PC shut itself down and then
re-start at least 30 seconds later. The timing does not have to be
that exact... just so it actually powers off and stays that way for at
least a few seconds.... At 0200 in the morning, nobody's going to care
as long as the sys is back up by sunrise.

Can anybody point to a way to accomplish this without spending a lot of
money on something like a remote-controlled power strip?


How is the IP cam powered ?
Is it POE ?
A 12V adapter of some sort ?

What is the make and model number of the IP cam ?

Paul
  #4  
Old May 30th 13, 01:18 AM posted to alt.windows7.general
Bob I
external usenet poster
 
Posts: 9,943
Default Delayed Re-Boot?

31 bucks too expensive?

http://www.amazon.com/Power-Single-O...=pd_sim_misc_1


On 5/29/2013 4:05 PM, (PeteCresswell) wrote:
I have an IP cam hanging on a Windows 7 box about 80 miles from home.

Every so often, the cam goes brain-dead and the only way to get it back
is to cut power to the cam and then restore power - causing the cam to
do a cold start.

I thought I had it licked when I put in one of those power strips that
senses how much the PC is drawing and cuts power to everything else
plugged in to it when it senses that the PC is no longer drawing power
above a certain level.

The plan was to just TeamViewer into the PC and issue a manual re-boot
if/when the cam went South.

But that does not work. I am guessing that a re-boot does not reduce
the power consumption long enough to trip the power strip.

What I would like to do is somehow have the PC shut itself down and then
re-start at least 30 seconds later. The timing does not have to be
that exact... just so it actually powers off and stays that way for at
least a few seconds.... At 0200 in the morning, nobody's going to care
as long as the sys is back up by sunrise.

Can anybody point to a way to accomplish this without spending a lot of
money on something like a remote-controlled power strip?

  #5  
Old May 30th 13, 01:22 AM posted to alt.windows7.general
Gene E. Bloch[_2_]
external usenet poster
 
Posts: 7,485
Default Delayed Re-Boot?

On Wed, 29 May 2013 17:05:21 -0400, (PeteCresswell) wrote:

I have an IP cam hanging on a Windows 7 box about 80 miles from home.

Every so often, the cam goes brain-dead and the only way to get it back
is to cut power to the cam and then restore power - causing the cam to
do a cold start.

I thought I had it licked when I put in one of those power strips that
senses how much the PC is drawing and cuts power to everything else
plugged in to it when it senses that the PC is no longer drawing power
above a certain level.

The plan was to just TeamViewer into the PC and issue a manual re-boot
if/when the cam went South.

But that does not work. I am guessing that a re-boot does not reduce
the power consumption long enough to trip the power strip.

What I would like to do is somehow have the PC shut itself down and then
re-start at least 30 seconds later. The timing does not have to be
that exact... just so it actually powers off and stays that way for at
least a few seconds.... At 0200 in the morning, nobody's going to care
as long as the sys is back up by sunrise.

Can anybody point to a way to accomplish this without spending a lot of
money on something like a remote-controlled power strip?


I don't know how to do this:

Power the camera through a device that the computer can shut down.

My idea is like a relay that is controlled by a signal over USB. For
safety, it could control the 5V (or is it 12V) side of the camera's
power, rather than the 120V side.

I say this because it seems clear that you are already controlling the
computer from afar...

--
Gene E. Bloch (Stumbling Bloch)
  #6  
Old May 30th 13, 01:27 AM posted to alt.windows7.general
Gene E. Bloch[_2_]
external usenet poster
 
Posts: 7,485
Default Delayed Re-Boot?

On Wed, 29 May 2013 19:18:43 -0500, Bob I wrote:

31 bucks too expensive?

http://www.amazon.com/Power-Single-O...=pd_sim_misc_1


You sure did a great job of making my post redundant :-)

Talk about timing...

I good a good laugh out of your reply - and you make me wish I had a
need for one of those! Maybe I'll just order one and hope I come up with
a plan...

On 5/29/2013 4:05 PM, (PeteCresswell) wrote:
I have an IP cam hanging on a Windows 7 box about 80 miles from home.

Every so often, the cam goes brain-dead and the only way to get it back
is to cut power to the cam and then restore power - causing the cam to
do a cold start.

I thought I had it licked when I put in one of those power strips that
senses how much the PC is drawing and cuts power to everything else
plugged in to it when it senses that the PC is no longer drawing power
above a certain level.

The plan was to just TeamViewer into the PC and issue a manual re-boot
if/when the cam went South.

But that does not work. I am guessing that a re-boot does not reduce
the power consumption long enough to trip the power strip.

What I would like to do is somehow have the PC shut itself down and then
re-start at least 30 seconds later. The timing does not have to be
that exact... just so it actually powers off and stays that way for at
least a few seconds.... At 0200 in the morning, nobody's going to care
as long as the sys is back up by sunrise.

Can anybody point to a way to accomplish this without spending a lot of
money on something like a remote-controlled power strip?


--
Gene E. Bloch (Stumbling Bloch)
  #7  
Old May 30th 13, 08:17 PM posted to alt.windows7.general
Yousuf Khan[_2_]
external usenet poster
 
Posts: 2,447
Default Delayed Re-Boot?

On 29/05/2013 5:05 PM, (PeteCresswell) wrote:
I have an IP cam hanging on a Windows 7 box about 80 miles from home.

Every so often, the cam goes brain-dead and the only way to get it back
is to cut power to the cam and then restore power - causing the cam to
do a cold start.


I'm thinking your choice would be to put the PC into a hibernate state,
and then reawaken it with Wake-On-LAN command? The hibernate is nearly
identical to a power-off.

Yousuf Khan

  #8  
Old May 30th 13, 08:25 PM posted to alt.windows7.general
Bert[_3_]
external usenet poster
 
Posts: 217
Default Delayed Re-Boot?

In Yousuf Khan
wrote:

On 29/05/2013 5:05 PM, (PeteCresswell) wrote:
I have an IP cam hanging on a Windows 7 box about 80 miles from home.

Every so often, the cam goes brain-dead and the only way to get it back
is to cut power to the cam and then restore power - causing the cam to
do a cold start.


I'm thinking your choice would be to put the PC into a hibernate state,
and then reawaken it with Wake-On-LAN command? The hibernate is nearly
identical to a power-off.


Then he might just as well do a full shutdown of the PC.

He'd trade the small additional time it takes to boot compared to recovery
from hibernation with the advantage of cleaning out the cobwebs that
accumulate in a machine that's been running too long without being
rebooted. Maybe Windows 7 doesn't suffer from this the way XP did, but I
wouldn't bet on it.

On the other hand, from the description I'd bet that this requires "Wake On
WAN" rather than "Wake on LAN," since the PC sounds like it's probably on
another network segment from the poster's other PCs. The process for Wake
on WAN is slightly different from Wake On LAN.

--
St. Paul, MN
  #9  
Old May 31st 13, 01:05 AM posted to alt.windows7.general
(PeteCresswell)
external usenet poster
 
Posts: 1,933
Default Delayed Re-Boot?

Per Paul in Houston TX:
Timer? I have one of those old motor driven ones that
can turn something off then back on 15 minutes later.
Electronic versions have their own clock in case the
power goes off for a while.


That was going to be my fallback position: timer that cycles power once
every 24 hours. But this thing is in somebody's home office and all
the timers I've used make some noise... so I was avoiding it. ALso,
the brass ring is to be able to do it on command - although that's
probably far from necessary.
--
Pete Cresswell
  #10  
Old May 31st 13, 01:06 AM posted to alt.windows7.general
(PeteCresswell)
external usenet poster
 
Posts: 1,933
Default Delayed Re-Boot?

Per Paul:
How is the IP cam powered ?
Is it POE ?
A 12V adapter of some sort ?

What is the make and model number of the IP cam ?


ACTi KCM-5311. POE. Great cam so far. No night vision to speak of,
but we only use it during the day. 32x zoom gets used continually.

ExtremeSurfCam.DynDNS.org:8080
--
Pete Cresswell
  #11  
Old May 31st 13, 01:08 AM posted to alt.windows7.general
(PeteCresswell)
external usenet poster
 
Posts: 1,933
Default Delayed Re-Boot?

Per Bob I:
31 bucks too expensive?

http://www.amazon.com/Power-Single-O...=pd_sim_misc_1



I think we may have a winner!!

Thanks.
--
Pete Cresswell
  #12  
Old May 31st 13, 01:40 AM posted to alt.windows7.general
Bob I
external usenet poster
 
Posts: 9,943
Default Delayed Re-Boot?



On 5/30/2013 7:08 PM, (PeteCresswell) wrote:
Per Bob I:
31 bucks too expensive?

http://www.amazon.com/Power-Single-O...=pd_sim_misc_1



I think we may have a winner!!

Thanks.


Welcome!
  #13  
Old May 31st 13, 01:46 AM posted to alt.windows7.general
Bob I
external usenet poster
 
Posts: 9,943
Default Delayed Re-Boot?



On 5/29/2013 7:27 PM, Gene E. Bloch wrote:
On Wed, 29 May 2013 19:18:43 -0500, Bob I wrote:

31 bucks too expensive?

http://www.amazon.com/Power-Single-O...=pd_sim_misc_1


You sure did a great job of making my post redundant :-)

Talk about timing...

I good a good laugh out of your reply - and you make me wish I had a
need for one of those! Maybe I'll just order one and hope I come up with
a plan...


These are more fun but overkill for Pete, but maybe what you could use.

http://www.x10.com/products/x10_ck11a.htm


  #14  
Old May 31st 13, 01:59 AM posted to alt.windows7.general
Paul in Houston TX
external usenet poster
 
Posts: 744
Default Delayed Re-Boot?

(PeteCresswell) wrote:
Per Paul in Houston TX:
Timer? I have one of those old motor driven ones that
can turn something off then back on 15 minutes later.
Electronic versions have their own clock in case the
power goes off for a while.


That was going to be my fallback position: timer that cycles power once
every 24 hours. But this thing is in somebody's home office and all
the timers I've used make some noise... so I was avoiding it. ALso,
the brass ring is to be able to do it on command - although that's
probably far from necessary.


The digital electronic ones should be silent unless they
have a relay. I don't have one so can't verify.
We use cheap plug in timers in some of the computer equipment that
locks up during lightning storms to reboot them every 24 hours.
  #15  
Old May 31st 13, 02:47 AM posted to alt.windows7.general
Paul
external usenet poster
 
Posts: 18,275
Default Delayed Re-Boot?

(PeteCresswell) wrote:
Per Paul:
How is the IP cam powered ?
Is it POE ?
A 12V adapter of some sort ?

What is the make and model number of the IP cam ?


ACTi KCM-5311. POE. Great cam so far. No night vision to speak of,
but we only use it during the day. 32x zoom gets used continually.

ExtremeSurfCam.DynDNS.org:8080


Is there such a thing as "managed POE" ?

If so, you might be able to turn POE on and off on an
individual port of the switch.

But that would cost a fortune.

The USB to AC outlet switch is likely cheaper.

Paul
 




Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off






All times are GMT +1. The time now is 02:23 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 PCbanter.
The comments are property of their posters.