If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Print Job
Hello,
I am using XP Home, and an HP DeskJet 880C. Sometimes I have to stop a print job by turning off the printer, because stopping it from within the printer from control panel is to slow. However, when I do so I also then cancel printing from the control panel. Unfortunately, it seems to take 30 minutes for the job to actually cancel and the icon to disappear from my system tray. I cannot turn the printer on again before this, because if I do, it will just try to finish the job. So, is there anyway to get it to cancel quicker? Alternatively, is there anyway to get the printer shut down in windows quicker? Any help would be greatly appreciated. -- Regards, Bob Brannon |
Ads |
#2
|
|||
|
|||
Print Job
Go to the Command Prompt and type
net stop spooler (and hit enter) This should stop the Print Spooler immediately. Of course, it won't have much effect if you aren't using the Print Spooler and have changed the default to Print Directly to Printer. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello, I am using XP Home, and an HP DeskJet 880C. Sometimes I have to stop a print job by turning off the printer, because stopping it from within the printer from control panel is to slow. However, when I do so I also then cancel printing from the control panel. Unfortunately, it seems to take 30 minutes for the job to actually cancel and the icon to disappear from my system tray. I cannot turn the printer on again before this, because if I do, it will just try to finish the job. So, is there anyway to get it to cancel quicker? Alternatively, is there anyway to get the printer shut down in windows quicker? Any help would be greatly appreciated. -- Regards, Bob Brannon |
#3
|
|||
|
|||
Print Job
That did the trick! Thank you very much for your help. I initially put
this message out on 3/6/2004 but no one picked up on it, so thanks again! -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Go to the Command Prompt and type net stop spooler (and hit enter) This should stop the Print Spooler immediately. Of course, it won't have much effect if you aren't using the Print Spooler and have changed the default to Print Directly to Printer. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello, I am using XP Home, and an HP DeskJet 880C. Sometimes I have to stop a print job by turning off the printer, because stopping it from within the printer from control panel is to slow. However, when I do so I also then cancel printing from the control panel. Unfortunately, it seems to take 30 minutes for the job to actually cancel and the icon to disappear from my system tray. I cannot turn the printer on again before this, because if I do, it will just try to finish the job. So, is there anyway to get it to cancel quicker? Alternatively, is there anyway to get the printer shut down in windows quicker? Any help would be greatly appreciated. -- Regards, Bob Brannon |
#4
|
|||
|
|||
Print Job
Sorry I must have missed it back then... glad it's now fine! (Maybe I was
snowed under by Lexmarks!) Cari www.coribright.com "Bob Brannon" wrote in message ... That did the trick! Thank you very much for your help. I initially put this message out on 3/6/2004 but no one picked up on it, so thanks again! -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Go to the Command Prompt and type net stop spooler (and hit enter) This should stop the Print Spooler immediately. Of course, it won't have much effect if you aren't using the Print Spooler and have changed the default to Print Directly to Printer. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello, I am using XP Home, and an HP DeskJet 880C. Sometimes I have to stop a print job by turning off the printer, because stopping it from within the printer from control panel is to slow. However, when I do so I also then cancel printing from the control panel. Unfortunately, it seems to take 30 minutes for the job to actually cancel and the icon to disappear from my system tray. I cannot turn the printer on again before this, because if I do, it will just try to finish the job. So, is there anyway to get it to cancel quicker? Alternatively, is there anyway to get the printer shut down in windows quicker? Any help would be greatly appreciated. -- Regards, Bob Brannon |
#5
|
|||
|
|||
Print Job
Hello Cari,
I hope you are still there. If I use your fix it works but found that I can't print again without starting up the service again from XP services. And, if I start the spooler to soon it prints the job anyway. Is there a way around this? -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Sorry I must have missed it back then... glad it's now fine! (Maybe I was snowed under by Lexmarks!) Cari www.coribright.com "Bob Brannon" wrote in message ... That did the trick! Thank you very much for your help. I initially put this message out on 3/6/2004 but no one picked up on it, so thanks again! -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Go to the Command Prompt and type net stop spooler (and hit enter) This should stop the Print Spooler immediately. Of course, it won't have much effect if you aren't using the Print Spooler and have changed the default to Print Directly to Printer. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello, I am using XP Home, and an HP DeskJet 880C. Sometimes I have to stop a print job by turning off the printer, because stopping it from within the printer from control panel is to slow. However, when I do so I also then cancel printing from the control panel. Unfortunately, it seems to take 30 minutes for the job to actually cancel and the icon to disappear from my system tray. I cannot turn the printer on again before this, because if I do, it will just try to finish the job. So, is there anyway to get it to cancel quicker? Alternatively, is there anyway to get the printer shut down in windows quicker? Any help would be greatly appreciated. -- Regards, Bob Brannon |
#6
|
|||
|
|||
Print Job
I'm still here.... I think I live in here!
Try stopping the print spooler and then deleting the print job. You will have to start the Print Spooler manually after stopping it..... that's the way it usually works. A manual stop followed by a manual start. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello Cari, I hope you are still there. If I use your fix it works but found that I can't print again without starting up the service again from XP services. And, if I start the spooler to soon it prints the job anyway. Is there a way around this? -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Sorry I must have missed it back then... glad it's now fine! (Maybe I was snowed under by Lexmarks!) Cari www.coribright.com "Bob Brannon" wrote in message ... That did the trick! Thank you very much for your help. I initially put this message out on 3/6/2004 but no one picked up on it, so thanks again! -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Go to the Command Prompt and type net stop spooler (and hit enter) This should stop the Print Spooler immediately. Of course, it won't have much effect if you aren't using the Print Spooler and have changed the default to Print Directly to Printer. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello, I am using XP Home, and an HP DeskJet 880C. Sometimes I have to stop a print job by turning off the printer, because stopping it from within the printer from control panel is to slow. However, when I do so I also then cancel printing from the control panel. Unfortunately, it seems to take 30 minutes for the job to actually cancel and the icon to disappear from my system tray. I cannot turn the printer on again before this, because if I do, it will just try to finish the job. So, is there anyway to get it to cancel quicker? Alternatively, is there anyway to get the printer shut down in windows quicker? Any help would be greatly appreciated. -- Regards, Bob Brannon |
#7
|
|||
|
|||
Print Job
Hello Cari,
I hope you are still there. If I use your fix it works but found that I can't print again without starting up the service again from XP services. And, if I start the spooler to soon it prints the job anyway. Is there a way around this? -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Sorry I must have missed it back then... glad it's now fine! (Maybe I was snowed under by Lexmarks!) Cari www.coribright.com "Bob Brannon" wrote in message ... That did the trick! Thank you very much for your help. I initially put this message out on 3/6/2004 but no one picked up on it, so thanks again! -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Go to the Command Prompt and type net stop spooler (and hit enter) This should stop the Print Spooler immediately. Of course, it won't have much effect if you aren't using the Print Spooler and have changed the default to Print Directly to Printer. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello, I am using XP Home, and an HP DeskJet 880C. Sometimes I have to stop a print job by turning off the printer, because stopping it from within the printer from control panel is to slow. However, when I do so I also then cancel printing from the control panel. Unfortunately, it seems to take 30 minutes for the job to actually cancel and the icon to disappear from my system tray. I cannot turn the printer on again before this, because if I do, it will just try to finish the job. So, is there anyway to get it to cancel quicker? Alternatively, is there anyway to get the printer shut down in windows quicker? Any help would be greatly appreciated. -- Regards, Bob Brannon |
#8
|
|||
|
|||
Print Job
I'm still here.... I think I live in here!
Try stopping the print spooler and then deleting the print job. You will have to start the Print Spooler manually after stopping it..... that's the way it usually works. A manual stop followed by a manual start. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello Cari, I hope you are still there. If I use your fix it works but found that I can't print again without starting up the service again from XP services. And, if I start the spooler to soon it prints the job anyway. Is there a way around this? -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Sorry I must have missed it back then... glad it's now fine! (Maybe I was snowed under by Lexmarks!) Cari www.coribright.com "Bob Brannon" wrote in message ... That did the trick! Thank you very much for your help. I initially put this message out on 3/6/2004 but no one picked up on it, so thanks again! -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Go to the Command Prompt and type net stop spooler (and hit enter) This should stop the Print Spooler immediately. Of course, it won't have much effect if you aren't using the Print Spooler and have changed the default to Print Directly to Printer. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello, I am using XP Home, and an HP DeskJet 880C. Sometimes I have to stop a print job by turning off the printer, because stopping it from within the printer from control panel is to slow. However, when I do so I also then cancel printing from the control panel. Unfortunately, it seems to take 30 minutes for the job to actually cancel and the icon to disappear from my system tray. I cannot turn the printer on again before this, because if I do, it will just try to finish the job. So, is there anyway to get it to cancel quicker? Alternatively, is there anyway to get the printer shut down in windows quicker? Any help would be greatly appreciated. -- Regards, Bob Brannon |
#9
|
|||
|
|||
Print Job
Hello Cari,
I hope you are still there. If I use your fix it works but found that I can't print again without starting up the service again from XP services. And, if I start the spooler to soon it prints the job anyway. Is there a way around this? -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Sorry I must have missed it back then... glad it's now fine! (Maybe I was snowed under by Lexmarks!) Cari www.coribright.com "Bob Brannon" wrote in message ... That did the trick! Thank you very much for your help. I initially put this message out on 3/6/2004 but no one picked up on it, so thanks again! -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Go to the Command Prompt and type net stop spooler (and hit enter) This should stop the Print Spooler immediately. Of course, it won't have much effect if you aren't using the Print Spooler and have changed the default to Print Directly to Printer. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello, I am using XP Home, and an HP DeskJet 880C. Sometimes I have to stop a print job by turning off the printer, because stopping it from within the printer from control panel is to slow. However, when I do so I also then cancel printing from the control panel. Unfortunately, it seems to take 30 minutes for the job to actually cancel and the icon to disappear from my system tray. I cannot turn the printer on again before this, because if I do, it will just try to finish the job. So, is there anyway to get it to cancel quicker? Alternatively, is there anyway to get the printer shut down in windows quicker? Any help would be greatly appreciated. -- Regards, Bob Brannon |
#10
|
|||
|
|||
Print Job
I'm still here.... I think I live in here!
Try stopping the print spooler and then deleting the print job. You will have to start the Print Spooler manually after stopping it..... that's the way it usually works. A manual stop followed by a manual start. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello Cari, I hope you are still there. If I use your fix it works but found that I can't print again without starting up the service again from XP services. And, if I start the spooler to soon it prints the job anyway. Is there a way around this? -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Sorry I must have missed it back then... glad it's now fine! (Maybe I was snowed under by Lexmarks!) Cari www.coribright.com "Bob Brannon" wrote in message ... That did the trick! Thank you very much for your help. I initially put this message out on 3/6/2004 but no one picked up on it, so thanks again! -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Go to the Command Prompt and type net stop spooler (and hit enter) This should stop the Print Spooler immediately. Of course, it won't have much effect if you aren't using the Print Spooler and have changed the default to Print Directly to Printer. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello, I am using XP Home, and an HP DeskJet 880C. Sometimes I have to stop a print job by turning off the printer, because stopping it from within the printer from control panel is to slow. However, when I do so I also then cancel printing from the control panel. Unfortunately, it seems to take 30 minutes for the job to actually cancel and the icon to disappear from my system tray. I cannot turn the printer on again before this, because if I do, it will just try to finish the job. So, is there anyway to get it to cancel quicker? Alternatively, is there anyway to get the printer shut down in windows quicker? Any help would be greatly appreciated. -- Regards, Bob Brannon |
#11
|
|||
|
|||
Print Job
Hello Cari,
I hope you are still there. If I use your fix it works but found that I can't print again without starting up the service again from XP services. And, if I start the spooler to soon it prints the job anyway. Is there a way around this? -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Sorry I must have missed it back then... glad it's now fine! (Maybe I was snowed under by Lexmarks!) Cari www.coribright.com "Bob Brannon" wrote in message ... That did the trick! Thank you very much for your help. I initially put this message out on 3/6/2004 but no one picked up on it, so thanks again! -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Go to the Command Prompt and type net stop spooler (and hit enter) This should stop the Print Spooler immediately. Of course, it won't have much effect if you aren't using the Print Spooler and have changed the default to Print Directly to Printer. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello, I am using XP Home, and an HP DeskJet 880C. Sometimes I have to stop a print job by turning off the printer, because stopping it from within the printer from control panel is to slow. However, when I do so I also then cancel printing from the control panel. Unfortunately, it seems to take 30 minutes for the job to actually cancel and the icon to disappear from my system tray. I cannot turn the printer on again before this, because if I do, it will just try to finish the job. So, is there anyway to get it to cancel quicker? Alternatively, is there anyway to get the printer shut down in windows quicker? Any help would be greatly appreciated. -- Regards, Bob Brannon |
#12
|
|||
|
|||
Print Job
I'm still here.... I think I live in here!
Try stopping the print spooler and then deleting the print job. You will have to start the Print Spooler manually after stopping it..... that's the way it usually works. A manual stop followed by a manual start. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello Cari, I hope you are still there. If I use your fix it works but found that I can't print again without starting up the service again from XP services. And, if I start the spooler to soon it prints the job anyway. Is there a way around this? -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Sorry I must have missed it back then... glad it's now fine! (Maybe I was snowed under by Lexmarks!) Cari www.coribright.com "Bob Brannon" wrote in message ... That did the trick! Thank you very much for your help. I initially put this message out on 3/6/2004 but no one picked up on it, so thanks again! -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Go to the Command Prompt and type net stop spooler (and hit enter) This should stop the Print Spooler immediately. Of course, it won't have much effect if you aren't using the Print Spooler and have changed the default to Print Directly to Printer. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello, I am using XP Home, and an HP DeskJet 880C. Sometimes I have to stop a print job by turning off the printer, because stopping it from within the printer from control panel is to slow. However, when I do so I also then cancel printing from the control panel. Unfortunately, it seems to take 30 minutes for the job to actually cancel and the icon to disappear from my system tray. I cannot turn the printer on again before this, because if I do, it will just try to finish the job. So, is there anyway to get it to cancel quicker? Alternatively, is there anyway to get the printer shut down in windows quicker? Any help would be greatly appreciated. -- Regards, Bob Brannon |
#13
|
|||
|
|||
Print Job
Hello Cari,
I hope you are still there. If I use your fix it works but found that I can't print again without starting up the service again from XP services. And, if I start the spooler to soon it prints the job anyway. Is there a way around this? -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Sorry I must have missed it back then... glad it's now fine! (Maybe I was snowed under by Lexmarks!) Cari www.coribright.com "Bob Brannon" wrote in message ... That did the trick! Thank you very much for your help. I initially put this message out on 3/6/2004 but no one picked up on it, so thanks again! -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Go to the Command Prompt and type net stop spooler (and hit enter) This should stop the Print Spooler immediately. Of course, it won't have much effect if you aren't using the Print Spooler and have changed the default to Print Directly to Printer. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello, I am using XP Home, and an HP DeskJet 880C. Sometimes I have to stop a print job by turning off the printer, because stopping it from within the printer from control panel is to slow. However, when I do so I also then cancel printing from the control panel. Unfortunately, it seems to take 30 minutes for the job to actually cancel and the icon to disappear from my system tray. I cannot turn the printer on again before this, because if I do, it will just try to finish the job. So, is there anyway to get it to cancel quicker? Alternatively, is there anyway to get the printer shut down in windows quicker? Any help would be greatly appreciated. -- Regards, Bob Brannon |
#14
|
|||
|
|||
Print Job
I'm still here.... I think I live in here!
Try stopping the print spooler and then deleting the print job. You will have to start the Print Spooler manually after stopping it..... that's the way it usually works. A manual stop followed by a manual start. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello Cari, I hope you are still there. If I use your fix it works but found that I can't print again without starting up the service again from XP services. And, if I start the spooler to soon it prints the job anyway. Is there a way around this? -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Sorry I must have missed it back then... glad it's now fine! (Maybe I was snowed under by Lexmarks!) Cari www.coribright.com "Bob Brannon" wrote in message ... That did the trick! Thank you very much for your help. I initially put this message out on 3/6/2004 but no one picked up on it, so thanks again! -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Go to the Command Prompt and type net stop spooler (and hit enter) This should stop the Print Spooler immediately. Of course, it won't have much effect if you aren't using the Print Spooler and have changed the default to Print Directly to Printer. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello, I am using XP Home, and an HP DeskJet 880C. Sometimes I have to stop a print job by turning off the printer, because stopping it from within the printer from control panel is to slow. However, when I do so I also then cancel printing from the control panel. Unfortunately, it seems to take 30 minutes for the job to actually cancel and the icon to disappear from my system tray. I cannot turn the printer on again before this, because if I do, it will just try to finish the job. So, is there anyway to get it to cancel quicker? Alternatively, is there anyway to get the printer shut down in windows quicker? Any help would be greatly appreciated. -- Regards, Bob Brannon |
#15
|
|||
|
|||
Print Job
Hello Cari,
I hope you are still there. If I use your fix it works but found that I can't print again without starting up the service again from XP services. And, if I start the spooler to soon it prints the job anyway. Is there a way around this? -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Sorry I must have missed it back then... glad it's now fine! (Maybe I was snowed under by Lexmarks!) Cari www.coribright.com "Bob Brannon" wrote in message ... That did the trick! Thank you very much for your help. I initially put this message out on 3/6/2004 but no one picked up on it, so thanks again! -- Regards, Bob Brannon "Cari (MS-MVP)" wrote in message ... Go to the Command Prompt and type net stop spooler (and hit enter) This should stop the Print Spooler immediately. Of course, it won't have much effect if you aren't using the Print Spooler and have changed the default to Print Directly to Printer. Cari www.coribright.com "Bob Brannon" wrote in message ... Hello, I am using XP Home, and an HP DeskJet 880C. Sometimes I have to stop a print job by turning off the printer, because stopping it from within the printer from control panel is to slow. However, when I do so I also then cancel printing from the control panel. Unfortunately, it seems to take 30 minutes for the job to actually cancel and the icon to disappear from my system tray. I cannot turn the printer on again before this, because if I do, it will just try to finish the job. So, is there anyway to get it to cancel quicker? Alternatively, is there anyway to get the printer shut down in windows quicker? Any help would be greatly appreciated. -- Regards, Bob Brannon |
Thread Tools | |
Display Modes | |
|
|