If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Procedure to replace my USB hub
I have a USB hub attached with a number of hardware devices plugged into it.
I believe that it is faulty and causing system reboots so I want to replace it with another hub that I know is not faulty. Should I do a Safe Hardware removal of all the devices that are plugged into the hub before replacing it with another hub or can I just power off, switch the usb hubs, plug in the devices and power up? |
Ads |
#2
|
|||
|
|||
Procedure to replace my USB hub
robertvemail-ssnb wrote:
I have a USB hub attached with a number of hardware devices plugged into it. I believe that it is faulty and causing system reboots so I want to replace it with another hub that I know is not faulty. Should I do a Safe Hardware removal of all the devices that are plugged into the hub before replacing it with another hub or can I just power off, switch the usb hubs, plug in the devices and power up? Properly shutdown the system. Unhook everything that has to do with the USB HUB. Replace the USB hub (I recommend a powered one.) Plug everything back in that has to do with the USB HUB. Power on the system. The USB Hub is not intelligent. -- Shenan Stanley MS-MVP -- How To Ask Questions The Smart Way http://www.catb.org/~esr/faqs/smart-questions.html |
#3
|
|||
|
|||
Procedure to replace my USB hub
robertvemail-ssnb wrote:
I have a USB hub attached with a number of hardware devices plugged into it. I believe that it is faulty and causing system reboots so I want to replace it with another hub that I know is not faulty. Should I do a Safe Hardware removal of all the devices that are plugged into the hub before replacing it with another hub or can I just power off, switch the usb hubs, plug in the devices and power up? Properly shutdown the system. Unhook everything that has to do with the USB HUB. Replace the USB hub (I recommend a powered one.) Plug everything back in that has to do with the USB HUB. Power on the system. The USB Hub is not intelligent. -- Shenan Stanley MS-MVP -- How To Ask Questions The Smart Way http://www.catb.org/~esr/faqs/smart-questions.html |
#4
|
|||
|
|||
Procedure to replace my USB hub
Since the USB hub is not intelligent and I am talking about 10 USB devices
woud I not get 10 instances of the Found New Hardware wizard at the same time. I am going from a 13-port hub to two stackable Belkin 7-port hubs driven off two USB ports at the rear of the computer. Like the current hub the new hubs will each be powered from the mains. |
#5
|
|||
|
|||
Procedure to replace my USB hub
Since the USB hub is not intelligent and I am talking about 10 USB devices
woud I not get 10 instances of the Found New Hardware wizard at the same time. I am going from a 13-port hub to two stackable Belkin 7-port hubs driven off two USB ports at the rear of the computer. Like the current hub the new hubs will each be powered from the mains. |
#6
|
|||
|
|||
Procedure to replace my USB hub
wrote in message ... Since the USB hub is not intelligent and I am talking about 10 USB devices woud I not get 10 instances of the Found New Hardware wizard at the same time. I am going from a 13-port hub to two stackable Belkin 7-port hubs driven off two USB ports at the rear of the computer. Like the current hub the new hubs will each be powered from the mains. If the PC is powered off at the time you swap the hubs, you're not going to get the new hardware wizard since those devices are already installed. Like Shenan stated, the hubs and their ports are not intelligent, they are just passive ports passing through the info from the attached devices. By "powered from the mains," does that mean external power from a wall plug? SC Tom |
#7
|
|||
|
|||
Procedure to replace my USB hub
wrote in message ... Since the USB hub is not intelligent and I am talking about 10 USB devices woud I not get 10 instances of the Found New Hardware wizard at the same time. I am going from a 13-port hub to two stackable Belkin 7-port hubs driven off two USB ports at the rear of the computer. Like the current hub the new hubs will each be powered from the mains. If the PC is powered off at the time you swap the hubs, you're not going to get the new hardware wizard since those devices are already installed. Like Shenan stated, the hubs and their ports are not intelligent, they are just passive ports passing through the info from the attached devices. By "powered from the mains," does that mean external power from a wall plug? SC Tom |
#8
|
|||
|
|||
Procedure to replace my USB hub
robertvemail-ssnb wrote:
I have a USB hub attached with a number of hardware devices plugged into it. I believe that it is faulty and causing system reboots so I want to replace it with another hub that I know is not faulty. Should I do a Safe Hardware removal of all the devices that are plugged into the hub before replacing it with another hub or can I just power off, switch the usb hubs, plug in the devices and power up? Shenan Stanley wrote: Properly shutdown the system. Unhook everything that has to do with the USB HUB. Replace the USB hub (I recommend a powered one.) Plug everything back in that has to do with the USB HUB. Power on the system. The USB Hub is not intelligent. robertvemail-ssnb wrote: Since the USB hub is not intelligent and I am talking about 10 USB devices woud I not get 10 instances of the Found New Hardware wizard at the same time. I am going from a 13-port hub to two stackable Belkin 7-port hubs driven off two USB ports at the rear of the computer. Like the current hub the new hubs will each be powered from the mains. Again - get powered USB hubs - especially with that ridiculous amount of USB devices. *grin* The way you want to do it is the way I have presented. Devices will have to be re-located, yep - but they aren't called universal serial buses for nothing. ;-) With that many devices (seriously?) you might be better off with this method (just for sanity): - Properly shutdown the system. - Unhook everything that has to do with the USB HUB. - Replace the USB hub (I recommend a powered one, especially in your case.) - Plug everything back that you *need* to have, like keyboard, mouse. Leave everything else unplugged. - Power on the system. - After it comes up and you are able to use the original two or so items you plugged in, begin plugging in the other stuff one at a time - giving each one time to be found and loaded and verifying you can access each one before going on to the next one. Now the real question everyone has to be thinking - why 10? Keyboard, mouse, a media card reader, fingerprint reader, printer, scanner, another printer, drawing pad and a couple of USB hard disk drives? -- Shenan Stanley MS-MVP -- How To Ask Questions The Smart Way http://www.catb.org/~esr/faqs/smart-questions.html |
#9
|
|||
|
|||
Procedure to replace my USB hub
robertvemail-ssnb wrote:
I have a USB hub attached with a number of hardware devices plugged into it. I believe that it is faulty and causing system reboots so I want to replace it with another hub that I know is not faulty. Should I do a Safe Hardware removal of all the devices that are plugged into the hub before replacing it with another hub or can I just power off, switch the usb hubs, plug in the devices and power up? Shenan Stanley wrote: Properly shutdown the system. Unhook everything that has to do with the USB HUB. Replace the USB hub (I recommend a powered one.) Plug everything back in that has to do with the USB HUB. Power on the system. The USB Hub is not intelligent. robertvemail-ssnb wrote: Since the USB hub is not intelligent and I am talking about 10 USB devices woud I not get 10 instances of the Found New Hardware wizard at the same time. I am going from a 13-port hub to two stackable Belkin 7-port hubs driven off two USB ports at the rear of the computer. Like the current hub the new hubs will each be powered from the mains. Again - get powered USB hubs - especially with that ridiculous amount of USB devices. *grin* The way you want to do it is the way I have presented. Devices will have to be re-located, yep - but they aren't called universal serial buses for nothing. ;-) With that many devices (seriously?) you might be better off with this method (just for sanity): - Properly shutdown the system. - Unhook everything that has to do with the USB HUB. - Replace the USB hub (I recommend a powered one, especially in your case.) - Plug everything back that you *need* to have, like keyboard, mouse. Leave everything else unplugged. - Power on the system. - After it comes up and you are able to use the original two or so items you plugged in, begin plugging in the other stuff one at a time - giving each one time to be found and loaded and verifying you can access each one before going on to the next one. Now the real question everyone has to be thinking - why 10? Keyboard, mouse, a media card reader, fingerprint reader, printer, scanner, another printer, drawing pad and a couple of USB hard disk drives? -- Shenan Stanley MS-MVP -- How To Ask Questions The Smart Way http://www.catb.org/~esr/faqs/smart-questions.html |
#10
|
|||
|
|||
Procedure to replace my USB hub
On Sep 21, 6:56*pm, "Shenan Stanley" wrote:
robertvemail-ssnb wrote: I have a USB hub attached with a number of hardware devices plugged into it. I believe that it is faulty and causing system reboots so I want to replace it with another hub that I know is not faulty. Should I do a Safe Hardware removal of all the devices that are plugged into the hub before replacing it with another hub or can I just power off, switch the usb hubs, plug in the devices and power up? Properly shutdown the system. Unhook everything that has to do with the USB HUB. Replace the USB hub (I recommend a powered one.) Plug everything back in that has to do with the USB HUB. Power on the system. The USB Hub is not intelligent. -- Shenan Stanley * * *MS-MVP -- How To Ask Questions The Smart Wayhttp://www.catb.org/~esr/faqs/smart-questions.html Even though this process will work, it will leave several of the attached devices as "ghost" devices. Once the hub is replaced, you should go back and remove these "ghosted" devices for cleanup: Click on Start Click on Run Enter : CMD In the Command Prompt "window" enter the following: set devmgr_show_nonpresent_devices=1 cd %SystemRoot%\System32 start devmgmt.msc Once on Device Manager, "check off" "Show hidden devices..." and the work on uninstall the "ghosted" devices. |
#11
|
|||
|
|||
Procedure to replace my USB hub
On Sep 21, 6:56*pm, "Shenan Stanley" wrote:
robertvemail-ssnb wrote: I have a USB hub attached with a number of hardware devices plugged into it. I believe that it is faulty and causing system reboots so I want to replace it with another hub that I know is not faulty. Should I do a Safe Hardware removal of all the devices that are plugged into the hub before replacing it with another hub or can I just power off, switch the usb hubs, plug in the devices and power up? Properly shutdown the system. Unhook everything that has to do with the USB HUB. Replace the USB hub (I recommend a powered one.) Plug everything back in that has to do with the USB HUB. Power on the system. The USB Hub is not intelligent. -- Shenan Stanley * * *MS-MVP -- How To Ask Questions The Smart Wayhttp://www.catb.org/~esr/faqs/smart-questions.html Even though this process will work, it will leave several of the attached devices as "ghost" devices. Once the hub is replaced, you should go back and remove these "ghosted" devices for cleanup: Click on Start Click on Run Enter : CMD In the Command Prompt "window" enter the following: set devmgr_show_nonpresent_devices=1 cd %SystemRoot%\System32 start devmgmt.msc Once on Device Manager, "check off" "Show hidden devices..." and the work on uninstall the "ghosted" devices. |
#12
|
|||
|
|||
Procedure to replace my USB hub
"smlunatick" wrote in message ... On Sep 21, 6:56 pm, "Shenan Stanley" wrote: robertvemail-ssnb wrote: I have a USB hub attached with a number of hardware devices plugged into it. I believe that it is faulty and causing system reboots so I want to replace it with another hub that I know is not faulty. Should I do a Safe Hardware removal of all the devices that are plugged into the hub before replacing it with another hub or can I just power off, switch the usb hubs, plug in the devices and power up? Properly shutdown the system. Unhook everything that has to do with the USB HUB. Replace the USB hub (I recommend a powered one.) Plug everything back in that has to do with the USB HUB. Power on the system. The USB Hub is not intelligent. -- Shenan Stanley MS-MVP -- How To Ask Questions The Smart Wayhttp://www.catb.org/~esr/faqs/smart-questions.html Even though this process will work, it will leave several of the attached devices as "ghost" devices. Once the hub is replaced, you should go back and remove these "ghosted" devices for cleanup: Click on Start Click on Run Enter : CMD In the Command Prompt "window" enter the following: set devmgr_show_nonpresent_devices=1 cd %SystemRoot%\System32 start devmgmt.msc Once on Device Manager, "check off" "Show hidden devices..." and the work on uninstall the "ghosted" devices. =========== Before doing this, make sure any device you are using is plugged in and powered on. If you remove a ghost of an installed device when it is powered off, the New Hardware wizard will start when you power it back on. SC Tom |
#13
|
|||
|
|||
Procedure to replace my USB hub
"smlunatick" wrote in message ... On Sep 21, 6:56 pm, "Shenan Stanley" wrote: robertvemail-ssnb wrote: I have a USB hub attached with a number of hardware devices plugged into it. I believe that it is faulty and causing system reboots so I want to replace it with another hub that I know is not faulty. Should I do a Safe Hardware removal of all the devices that are plugged into the hub before replacing it with another hub or can I just power off, switch the usb hubs, plug in the devices and power up? Properly shutdown the system. Unhook everything that has to do with the USB HUB. Replace the USB hub (I recommend a powered one.) Plug everything back in that has to do with the USB HUB. Power on the system. The USB Hub is not intelligent. -- Shenan Stanley MS-MVP -- How To Ask Questions The Smart Wayhttp://www.catb.org/~esr/faqs/smart-questions.html Even though this process will work, it will leave several of the attached devices as "ghost" devices. Once the hub is replaced, you should go back and remove these "ghosted" devices for cleanup: Click on Start Click on Run Enter : CMD In the Command Prompt "window" enter the following: set devmgr_show_nonpresent_devices=1 cd %SystemRoot%\System32 start devmgmt.msc Once on Device Manager, "check off" "Show hidden devices..." and the work on uninstall the "ghosted" devices. =========== Before doing this, make sure any device you are using is plugged in and powered on. If you remove a ghost of an installed device when it is powered off, the New Hardware wizard will start when you power it back on. SC Tom |
#14
|
|||
|
|||
Procedure to replace my USB hub
On 21 Wrz, 18:35, wrote:
I have a USB hub attached with a number of hardware devices plugged into it. I believe that it is faulty and causing system reboots so I want to replace it with another hub that I know is not faulty. Should I do a Safe Hardware removal of all the devices that are plugged into the hub before replacing it with another hub or can I just power off, switch the usb hubs, plug in the devices and power up? |
#15
|
|||
|
|||
Procedure to replace my USB hub
On 21 Wrz, 18:35, wrote:
I have a USB hub attached with a number of hardware devices plugged into it. I believe that it is faulty and causing system reboots so I want to replace it with another hub that I know is not faulty. Should I do a Safe Hardware removal of all the devices that are plugged into the hub before replacing it with another hub or can I just power off, switch the usb hubs, plug in the devices and power up? |
Thread Tools | |
Display Modes | |
|
|