A Windows XP help forum. PCbanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » PCbanter forum » Microsoft Windows XP » The Basics
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Computer won't boot



 
 
Thread Tools Display Modes
  #16  
Old February 28th 10, 11:18 PM posted to microsoft.public.windowsxp.basics
Antares 531[_2_]
external usenet poster
 
Posts: 385
Default Computer won't boot

On Sun, 28 Feb 2010 17:22:46 -0400, John John - MVP
wrote:


Antares 531 wrote:
On Sun, 28 Feb 2010 12:15:36 -0500, "glee"
wrote:

"Antares 531" wrote in message
...
On Sun, 28 Feb 2010 11:04:53 -0500, "glee"
wrote:

"Antares 531" wrote in message
...
I have an older computer with a Gigabyte GA-P35-DS3L motherboard that
I home-built a few years back. I recently built a new computer and
have been keeping the old one alive until I get the new one all
checked out and settled in.

Yesterday the old computer wouldn't boot. It makes a BEEP about one
second long during the boot process but won't go any farther. The
drive lights flash and the monitor goes through its first sign of
lighting up, after I turn the computer on, but this is as far as it
goes. The monitor goes black and the activity lights on the front of
the computer flash a few times, then everything stops.

I've tried using the original Windows XP Pro installation disk, and
also a second boot disk that I slipstreamed with SP3 on it. Neither
boot disk will initiate a start-up process. The CD drive light
flashes
a few times then quits and nothing more happens after the BEEP.

Any ideas as to what I might try next?
That model mobo apparently has an Award BIOS. One LONG beep from an
Award BIOS often indicates a memory error. I would start by
re-seating
the RAM. If there is more than on stick of RAM try using just one,
then
the other (in the first RAM slot).
If no improvement, try reseating the PCI cards and other items
connected
to the motherboard (power connectors, etc).

It could be other things, but that's where to start.

Thanks, Glee, I followed your suggestion but didn't get any favorable
results.

I powered down, pulled the power cord then removed the RAM stick out
of the DDRII 2 slot then booted and still got the beep.

I then powered down pulled the power cord and removed the RAM stick
from the DDRII 1 slot and replaced it with the one I had removed from
the other slot. Still beeped at me.

I powered down again, pulled the power cord, then put the second RAM
stick into the DDRII 2 slot. This had the two RAM sticks switched
around from their original positions. Still got the beep.

Something I noticed...the CPU cooling fan seems to be erratic. That is
it will start running as soon as I click the switch to boot up, but it
stops then jiggles intermittently when the beep sound occurs. After
the beep sound, this fan starts running normally without further
interruption. Could this mean that the CPU has failed?
It's hard to say, Gordon....it could be the power supply, or the mobo or
the CPU too.

Have you removed all the peripherals and cards except video, re-seated
absolutely everything, and tried again?

Try with the optical drives disconnected and only the hard drive
connected (and floppy drive if you have one).
Try with only the floppy drives connected if one is installed.
Try with NO drives connected.

A single long beep *usually* does not indicate a display problem.
This is a long beep, not the short beep one often hears during a normal
start-up, yes?

It's a slow process of re-seating, and disconnecting/reconnecting
everything to see if you get different behaviour...namely, if you can
get anything on the screen.

Does this have integrated video, or a separate video card?

If I had to make a total guess, I'd bet on a power supply problem. Do
you have a simple power supply tester, or a spare PSU you can try?

ATX PSU Tester
http://www.buy.com/prod/startech-com...202973591.html
and
http://www.amazon.com/StarTech-PSUTE.../dp/B000HVFBX8

I've gone through the process of removing and re-installing all the
add-in cards and interconnection cables. This didn't produce any
noticeable changes other than the CPU fan now runs in short bursts of
about 2 or 3 seconds whereas it was just jiggling like it was starting
to run but never actually rotated the fan.

To answer another question...I do have an nVidia e-GeForce 7600 GS
graphics card installed. This is a 512 MB PCI-E video card. I'm not
using the motherboard's graphics output.

I've not yet tested the power supply (PC Power & Cooling Silencer 470
ATX 12V, Ver 2.2), but it seems to be working okay in that all the
drive activity lights blink on and I can hear the drives spin up and
the read/write arms move.

I'm wondering if maybe the BIOS memory chip or battery has gone bad. I
built this computer in October, 2007. It shouldn't be near the point
of battery failure, I wouldn't think. Also, even if the BIOS battery
is dead, wouldn't the boot CD still work? Should I buy a fresh battery
and do a change-out?


Find the beep codes for your BIOS and your questions will be answered.
Glee says that the board has an Award BIOS so possible starting points:

http://search.yahoo.com/search;_ylt=...p&fr=yfp-t-501
http://search.yahoo.com/search;_ylt=...p&fr=yfp-t-501
http://search.yahoo.com/search;_ylt=...p&fr=yfp-t-501

John

Thanks, John. I checked these out but didn't find any information on
one long beep from a Gigabyte GA-P35-DS3L motherboard with an Award
BIOS.

I have always gotten a short beep (half second, approximately) on
booting and the above sites indicate that this is a "System Normal"
signal. But this beep is very brief.

The beep I'm now getting is a single beep that lasts about two seconds
then nothing more. It definitely isn't a series of long - short beeps.

This computer has been in service for more than two years, and has
always been very reliable and stable. I've done nothing in the way of
hardware modifications or new software, recently.

When booting, the drive indicator lights all flash and act like the
system is going through the normal boot process. I can hear the hard
drives running and the CD drive will accept a boot CD and act like it
is trying to read it for a while but never makes any progress with
this.

Even after the computer quits trying to complete the boot process, I
can still open the CD tray and put a CD in then close it, but it won't
show any signs of trying to read the CD after the boot process has
quit.

I plan to go tomorrow and buy a new BIOS CMOS battery, then replace
the old one. It is more than two years old, and may be exhausted.

Thanks for your support. I'll keep you posted on any new developments.

Gordon
Ads
  #17  
Old February 28th 10, 11:18 PM posted to microsoft.public.windowsxp.basics
Antares 531[_2_]
external usenet poster
 
Posts: 385
Default Computer won't boot

On Sun, 28 Feb 2010 17:22:46 -0400, John John - MVP
wrote:


Antares 531 wrote:
On Sun, 28 Feb 2010 12:15:36 -0500, "glee"
wrote:

"Antares 531" wrote in message
...
On Sun, 28 Feb 2010 11:04:53 -0500, "glee"
wrote:

"Antares 531" wrote in message
...
I have an older computer with a Gigabyte GA-P35-DS3L motherboard that
I home-built a few years back. I recently built a new computer and
have been keeping the old one alive until I get the new one all
checked out and settled in.

Yesterday the old computer wouldn't boot. It makes a BEEP about one
second long during the boot process but won't go any farther. The
drive lights flash and the monitor goes through its first sign of
lighting up, after I turn the computer on, but this is as far as it
goes. The monitor goes black and the activity lights on the front of
the computer flash a few times, then everything stops.

I've tried using the original Windows XP Pro installation disk, and
also a second boot disk that I slipstreamed with SP3 on it. Neither
boot disk will initiate a start-up process. The CD drive light
flashes
a few times then quits and nothing more happens after the BEEP.

Any ideas as to what I might try next?
That model mobo apparently has an Award BIOS. One LONG beep from an
Award BIOS often indicates a memory error. I would start by
re-seating
the RAM. If there is more than on stick of RAM try using just one,
then
the other (in the first RAM slot).
If no improvement, try reseating the PCI cards and other items
connected
to the motherboard (power connectors, etc).

It could be other things, but that's where to start.

Thanks, Glee, I followed your suggestion but didn't get any favorable
results.

I powered down, pulled the power cord then removed the RAM stick out
of the DDRII 2 slot then booted and still got the beep.

I then powered down pulled the power cord and removed the RAM stick
from the DDRII 1 slot and replaced it with the one I had removed from
the other slot. Still beeped at me.

I powered down again, pulled the power cord, then put the second RAM
stick into the DDRII 2 slot. This had the two RAM sticks switched
around from their original positions. Still got the beep.

Something I noticed...the CPU cooling fan seems to be erratic. That is
it will start running as soon as I click the switch to boot up, but it
stops then jiggles intermittently when the beep sound occurs. After
the beep sound, this fan starts running normally without further
interruption. Could this mean that the CPU has failed?
It's hard to say, Gordon....it could be the power supply, or the mobo or
the CPU too.

Have you removed all the peripherals and cards except video, re-seated
absolutely everything, and tried again?

Try with the optical drives disconnected and only the hard drive
connected (and floppy drive if you have one).
Try with only the floppy drives connected if one is installed.
Try with NO drives connected.

A single long beep *usually* does not indicate a display problem.
This is a long beep, not the short beep one often hears during a normal
start-up, yes?

It's a slow process of re-seating, and disconnecting/reconnecting
everything to see if you get different behaviour...namely, if you can
get anything on the screen.

Does this have integrated video, or a separate video card?

If I had to make a total guess, I'd bet on a power supply problem. Do
you have a simple power supply tester, or a spare PSU you can try?

ATX PSU Tester
http://www.buy.com/prod/startech-com...202973591.html
and
http://www.amazon.com/StarTech-PSUTE.../dp/B000HVFBX8

I've gone through the process of removing and re-installing all the
add-in cards and interconnection cables. This didn't produce any
noticeable changes other than the CPU fan now runs in short bursts of
about 2 or 3 seconds whereas it was just jiggling like it was starting
to run but never actually rotated the fan.

To answer another question...I do have an nVidia e-GeForce 7600 GS
graphics card installed. This is a 512 MB PCI-E video card. I'm not
using the motherboard's graphics output.

I've not yet tested the power supply (PC Power & Cooling Silencer 470
ATX 12V, Ver 2.2), but it seems to be working okay in that all the
drive activity lights blink on and I can hear the drives spin up and
the read/write arms move.

I'm wondering if maybe the BIOS memory chip or battery has gone bad. I
built this computer in October, 2007. It shouldn't be near the point
of battery failure, I wouldn't think. Also, even if the BIOS battery
is dead, wouldn't the boot CD still work? Should I buy a fresh battery
and do a change-out?


Find the beep codes for your BIOS and your questions will be answered.
Glee says that the board has an Award BIOS so possible starting points:

http://search.yahoo.com/search;_ylt=...p&fr=yfp-t-501
http://search.yahoo.com/search;_ylt=...p&fr=yfp-t-501
http://search.yahoo.com/search;_ylt=...p&fr=yfp-t-501

John

Thanks, John. I checked these out but didn't find any information on
one long beep from a Gigabyte GA-P35-DS3L motherboard with an Award
BIOS.

I have always gotten a short beep (half second, approximately) on
booting and the above sites indicate that this is a "System Normal"
signal. But this beep is very brief.

The beep I'm now getting is a single beep that lasts about two seconds
then nothing more. It definitely isn't a series of long - short beeps.

This computer has been in service for more than two years, and has
always been very reliable and stable. I've done nothing in the way of
hardware modifications or new software, recently.

When booting, the drive indicator lights all flash and act like the
system is going through the normal boot process. I can hear the hard
drives running and the CD drive will accept a boot CD and act like it
is trying to read it for a while but never makes any progress with
this.

Even after the computer quits trying to complete the boot process, I
can still open the CD tray and put a CD in then close it, but it won't
show any signs of trying to read the CD after the boot process has
quit.

I plan to go tomorrow and buy a new BIOS CMOS battery, then replace
the old one. It is more than two years old, and may be exhausted.

Thanks for your support. I'll keep you posted on any new developments.

Gordon
  #18  
Old February 28th 10, 11:57 PM posted to microsoft.public.windowsxp.basics
Unknown
external usenet poster
 
Posts: 6,007
Default Computer won't boot

Try the process of elimination if you don't know the beep codes. I.E. Remove
a memory module and try to boot.
Then remove another item and try to boot.
"Antares 531" wrote in message
...
On Sun, 28 Feb 2010 17:22:46 -0400, John John - MVP
wrote:


Antares 531 wrote:
On Sun, 28 Feb 2010 12:15:36 -0500, "glee"
wrote:

"Antares 531" wrote in message
...
On Sun, 28 Feb 2010 11:04:53 -0500, "glee"
wrote:

"Antares 531" wrote in message
...
I have an older computer with a Gigabyte GA-P35-DS3L motherboard
that
I home-built a few years back. I recently built a new computer and
have been keeping the old one alive until I get the new one all
checked out and settled in.

Yesterday the old computer wouldn't boot. It makes a BEEP about one
second long during the boot process but won't go any farther. The
drive lights flash and the monitor goes through its first sign of
lighting up, after I turn the computer on, but this is as far as it
goes. The monitor goes black and the activity lights on the front of
the computer flash a few times, then everything stops.

I've tried using the original Windows XP Pro installation disk, and
also a second boot disk that I slipstreamed with SP3 on it. Neither
boot disk will initiate a start-up process. The CD drive light
flashes
a few times then quits and nothing more happens after the BEEP.

Any ideas as to what I might try next?
That model mobo apparently has an Award BIOS. One LONG beep from an
Award BIOS often indicates a memory error. I would start by
re-seating
the RAM. If there is more than on stick of RAM try using just one,
then
the other (in the first RAM slot).
If no improvement, try reseating the PCI cards and other items
connected
to the motherboard (power connectors, etc).

It could be other things, but that's where to start.

Thanks, Glee, I followed your suggestion but didn't get any favorable
results.

I powered down, pulled the power cord then removed the RAM stick out
of the DDRII 2 slot then booted and still got the beep.

I then powered down pulled the power cord and removed the RAM stick
from the DDRII 1 slot and replaced it with the one I had removed from
the other slot. Still beeped at me.

I powered down again, pulled the power cord, then put the second RAM
stick into the DDRII 2 slot. This had the two RAM sticks switched
around from their original positions. Still got the beep.

Something I noticed...the CPU cooling fan seems to be erratic. That is
it will start running as soon as I click the switch to boot up, but it
stops then jiggles intermittently when the beep sound occurs. After
the beep sound, this fan starts running normally without further
interruption. Could this mean that the CPU has failed?
It's hard to say, Gordon....it could be the power supply, or the mobo
or
the CPU too.

Have you removed all the peripherals and cards except video, re-seated
absolutely everything, and tried again?

Try with the optical drives disconnected and only the hard drive
connected (and floppy drive if you have one).
Try with only the floppy drives connected if one is installed.
Try with NO drives connected.

A single long beep *usually* does not indicate a display problem.
This is a long beep, not the short beep one often hears during a normal
start-up, yes?

It's a slow process of re-seating, and disconnecting/reconnecting
everything to see if you get different behaviour...namely, if you can
get anything on the screen.

Does this have integrated video, or a separate video card?

If I had to make a total guess, I'd bet on a power supply problem. Do
you have a simple power supply tester, or a spare PSU you can try?

ATX PSU Tester
http://www.buy.com/prod/startech-com...202973591.html
and
http://www.amazon.com/StarTech-PSUTE.../dp/B000HVFBX8

I've gone through the process of removing and re-installing all the
add-in cards and interconnection cables. This didn't produce any
noticeable changes other than the CPU fan now runs in short bursts of
about 2 or 3 seconds whereas it was just jiggling like it was starting
to run but never actually rotated the fan.

To answer another question...I do have an nVidia e-GeForce 7600 GS
graphics card installed. This is a 512 MB PCI-E video card. I'm not
using the motherboard's graphics output.

I've not yet tested the power supply (PC Power & Cooling Silencer 470
ATX 12V, Ver 2.2), but it seems to be working okay in that all the
drive activity lights blink on and I can hear the drives spin up and
the read/write arms move.

I'm wondering if maybe the BIOS memory chip or battery has gone bad. I
built this computer in October, 2007. It shouldn't be near the point
of battery failure, I wouldn't think. Also, even if the BIOS battery
is dead, wouldn't the boot CD still work? Should I buy a fresh battery
and do a change-out?


Find the beep codes for your BIOS and your questions will be answered.
Glee says that the board has an Award BIOS so possible starting points:

http://search.yahoo.com/search;_ylt=...p&fr=yfp-t-501
http://search.yahoo.com/search;_ylt=...p&fr=yfp-t-501
http://search.yahoo.com/search;_ylt=...p&fr=yfp-t-501

John

Thanks, John. I checked these out but didn't find any information on
one long beep from a Gigabyte GA-P35-DS3L motherboard with an Award
BIOS.

I have always gotten a short beep (half second, approximately) on
booting and the above sites indicate that this is a "System Normal"
signal. But this beep is very brief.

The beep I'm now getting is a single beep that lasts about two seconds
then nothing more. It definitely isn't a series of long - short beeps.

This computer has been in service for more than two years, and has
always been very reliable and stable. I've done nothing in the way of
hardware modifications or new software, recently.

When booting, the drive indicator lights all flash and act like the
system is going through the normal boot process. I can hear the hard
drives running and the CD drive will accept a boot CD and act like it
is trying to read it for a while but never makes any progress with
this.

Even after the computer quits trying to complete the boot process, I
can still open the CD tray and put a CD in then close it, but it won't
show any signs of trying to read the CD after the boot process has
quit.

I plan to go tomorrow and buy a new BIOS CMOS battery, then replace
the old one. It is more than two years old, and may be exhausted.

Thanks for your support. I'll keep you posted on any new developments.

Gordon



  #19  
Old February 28th 10, 11:57 PM posted to microsoft.public.windowsxp.basics
Unknown
external usenet poster
 
Posts: 6,007
Default Computer won't boot

Try the process of elimination if you don't know the beep codes. I.E. Remove
a memory module and try to boot.
Then remove another item and try to boot.
"Antares 531" wrote in message
...
On Sun, 28 Feb 2010 17:22:46 -0400, John John - MVP
wrote:


Antares 531 wrote:
On Sun, 28 Feb 2010 12:15:36 -0500, "glee"
wrote:

"Antares 531" wrote in message
...
On Sun, 28 Feb 2010 11:04:53 -0500, "glee"
wrote:

"Antares 531" wrote in message
...
I have an older computer with a Gigabyte GA-P35-DS3L motherboard
that
I home-built a few years back. I recently built a new computer and
have been keeping the old one alive until I get the new one all
checked out and settled in.

Yesterday the old computer wouldn't boot. It makes a BEEP about one
second long during the boot process but won't go any farther. The
drive lights flash and the monitor goes through its first sign of
lighting up, after I turn the computer on, but this is as far as it
goes. The monitor goes black and the activity lights on the front of
the computer flash a few times, then everything stops.

I've tried using the original Windows XP Pro installation disk, and
also a second boot disk that I slipstreamed with SP3 on it. Neither
boot disk will initiate a start-up process. The CD drive light
flashes
a few times then quits and nothing more happens after the BEEP.

Any ideas as to what I might try next?
That model mobo apparently has an Award BIOS. One LONG beep from an
Award BIOS often indicates a memory error. I would start by
re-seating
the RAM. If there is more than on stick of RAM try using just one,
then
the other (in the first RAM slot).
If no improvement, try reseating the PCI cards and other items
connected
to the motherboard (power connectors, etc).

It could be other things, but that's where to start.

Thanks, Glee, I followed your suggestion but didn't get any favorable
results.

I powered down, pulled the power cord then removed the RAM stick out
of the DDRII 2 slot then booted and still got the beep.

I then powered down pulled the power cord and removed the RAM stick
from the DDRII 1 slot and replaced it with the one I had removed from
the other slot. Still beeped at me.

I powered down again, pulled the power cord, then put the second RAM
stick into the DDRII 2 slot. This had the two RAM sticks switched
around from their original positions. Still got the beep.

Something I noticed...the CPU cooling fan seems to be erratic. That is
it will start running as soon as I click the switch to boot up, but it
stops then jiggles intermittently when the beep sound occurs. After
the beep sound, this fan starts running normally without further
interruption. Could this mean that the CPU has failed?
It's hard to say, Gordon....it could be the power supply, or the mobo
or
the CPU too.

Have you removed all the peripherals and cards except video, re-seated
absolutely everything, and tried again?

Try with the optical drives disconnected and only the hard drive
connected (and floppy drive if you have one).
Try with only the floppy drives connected if one is installed.
Try with NO drives connected.

A single long beep *usually* does not indicate a display problem.
This is a long beep, not the short beep one often hears during a normal
start-up, yes?

It's a slow process of re-seating, and disconnecting/reconnecting
everything to see if you get different behaviour...namely, if you can
get anything on the screen.

Does this have integrated video, or a separate video card?

If I had to make a total guess, I'd bet on a power supply problem. Do
you have a simple power supply tester, or a spare PSU you can try?

ATX PSU Tester
http://www.buy.com/prod/startech-com...202973591.html
and
http://www.amazon.com/StarTech-PSUTE.../dp/B000HVFBX8

I've gone through the process of removing and re-installing all the
add-in cards and interconnection cables. This didn't produce any
noticeable changes other than the CPU fan now runs in short bursts of
about 2 or 3 seconds whereas it was just jiggling like it was starting
to run but never actually rotated the fan.

To answer another question...I do have an nVidia e-GeForce 7600 GS
graphics card installed. This is a 512 MB PCI-E video card. I'm not
using the motherboard's graphics output.

I've not yet tested the power supply (PC Power & Cooling Silencer 470
ATX 12V, Ver 2.2), but it seems to be working okay in that all the
drive activity lights blink on and I can hear the drives spin up and
the read/write arms move.

I'm wondering if maybe the BIOS memory chip or battery has gone bad. I
built this computer in October, 2007. It shouldn't be near the point
of battery failure, I wouldn't think. Also, even if the BIOS battery
is dead, wouldn't the boot CD still work? Should I buy a fresh battery
and do a change-out?


Find the beep codes for your BIOS and your questions will be answered.
Glee says that the board has an Award BIOS so possible starting points:

http://search.yahoo.com/search;_ylt=...p&fr=yfp-t-501
http://search.yahoo.com/search;_ylt=...p&fr=yfp-t-501
http://search.yahoo.com/search;_ylt=...p&fr=yfp-t-501

John

Thanks, John. I checked these out but didn't find any information on
one long beep from a Gigabyte GA-P35-DS3L motherboard with an Award
BIOS.

I have always gotten a short beep (half second, approximately) on
booting and the above sites indicate that this is a "System Normal"
signal. But this beep is very brief.

The beep I'm now getting is a single beep that lasts about two seconds
then nothing more. It definitely isn't a series of long - short beeps.

This computer has been in service for more than two years, and has
always been very reliable and stable. I've done nothing in the way of
hardware modifications or new software, recently.

When booting, the drive indicator lights all flash and act like the
system is going through the normal boot process. I can hear the hard
drives running and the CD drive will accept a boot CD and act like it
is trying to read it for a while but never makes any progress with
this.

Even after the computer quits trying to complete the boot process, I
can still open the CD tray and put a CD in then close it, but it won't
show any signs of trying to read the CD after the boot process has
quit.

I plan to go tomorrow and buy a new BIOS CMOS battery, then replace
the old one. It is more than two years old, and may be exhausted.

Thanks for your support. I'll keep you posted on any new developments.

Gordon



  #20  
Old March 1st 10, 01:04 AM posted to microsoft.public.windowsxp.basics
Antares 531[_2_]
external usenet poster
 
Posts: 385
Default Computer won't boot

On Sun, 28 Feb 2010 16:57:56 -0600, "Unknown"
wrote:

Try the process of elimination if you don't know the beep codes. I.E. Remove
a memory module and try to boot.
Then remove another item and try to boot.

I tried that earlier today but didn't get any positive results. I
removed the #2 memory stick and tried booting...same long beep.

Next I removed both memory sticks and tried to boot but still got the
beep.

Then I removed the #1 memory stick and replaced it with what had
previously been the #2 memory stick and again it beeped at me.

Then I replaced both memory sticks in reverse position from their
original positions. This also got the beep sound.

I disconnected all the hard drives, CD and floppy then booted but
still got the beep.

I just noticed that the keyboard and mouse are not showing any life.
Earlier, the keyboard lights flashed when I booted but now they don't.

The hard drives, CD and floppy drive all seem to be working to the
point that I can hear the hard drives humming and if I put a CD in the
drive the activity light will blink and it seems to be trying to read
the CD. Same for the floppy drive.

I'm thinking that since I got the new computer up and running I've
left this old computer turned off for extended times and this may have
depleted what was left of the BIOS CMOS battery. If this battery went
completely dead the BIOS may not be working at all. I'll buy a new
battery tomorrow and see if that makes any difference. Start with the
little things and work my way up, I guess.

Gordon
  #21  
Old March 1st 10, 01:04 AM posted to microsoft.public.windowsxp.basics
Antares 531[_2_]
external usenet poster
 
Posts: 385
Default Computer won't boot

On Sun, 28 Feb 2010 16:57:56 -0600, "Unknown"
wrote:

Try the process of elimination if you don't know the beep codes. I.E. Remove
a memory module and try to boot.
Then remove another item and try to boot.

I tried that earlier today but didn't get any positive results. I
removed the #2 memory stick and tried booting...same long beep.

Next I removed both memory sticks and tried to boot but still got the
beep.

Then I removed the #1 memory stick and replaced it with what had
previously been the #2 memory stick and again it beeped at me.

Then I replaced both memory sticks in reverse position from their
original positions. This also got the beep sound.

I disconnected all the hard drives, CD and floppy then booted but
still got the beep.

I just noticed that the keyboard and mouse are not showing any life.
Earlier, the keyboard lights flashed when I booted but now they don't.

The hard drives, CD and floppy drive all seem to be working to the
point that I can hear the hard drives humming and if I put a CD in the
drive the activity light will blink and it seems to be trying to read
the CD. Same for the floppy drive.

I'm thinking that since I got the new computer up and running I've
left this old computer turned off for extended times and this may have
depleted what was left of the BIOS CMOS battery. If this battery went
completely dead the BIOS may not be working at all. I'll buy a new
battery tomorrow and see if that makes any difference. Start with the
little things and work my way up, I guess.

Gordon
  #22  
Old March 1st 10, 01:28 AM posted to microsoft.public.windowsxp.basics
Hot-text
external usenet poster
 
Posts: 239
Default Computer won't boot

BEEP about one second long during the boot process
Pull all the RAM stick out Restart Computer with out RAM stick if the long
BEEP go away it a Bad RAM stick!




"Antares 531" wrote in message
...
On Sun, 28 Feb 2010 12:15:36 -0500, "glee"
wrote:


"Antares 531" wrote in message
. ..
On Sun, 28 Feb 2010 11:04:53 -0500, "glee"
wrote:

"Antares 531" wrote in message
m...
I have an older computer with a Gigabyte GA-P35-DS3L motherboard that
I home-built a few years back. I recently built a new computer and
have been keeping the old one alive until I get the new one all
checked out and settled in.

Yesterday the old computer wouldn't boot. It makes a BEEP about one
second long during the boot process but won't go any farther. The
drive lights flash and the monitor goes through its first sign of
lighting up, after I turn the computer on, but this is as far as it
goes. The monitor goes black and the activity lights on the front of
the computer flash a few times, then everything stops.

I've tried using the original Windows XP Pro installation disk, and
also a second boot disk that I slipstreamed with SP3 on it. Neither
boot disk will initiate a start-up process. The CD drive light
flashes
a few times then quits and nothing more happens after the BEEP.

Any ideas as to what I might try next?

That model mobo apparently has an Award BIOS. One LONG beep from an
Award BIOS often indicates a memory error. I would start by
re-seating
the RAM. If there is more than on stick of RAM try using just one,
then
the other (in the first RAM slot).
If no improvement, try reseating the PCI cards and other items
connected
to the motherboard (power connectors, etc).

It could be other things, but that's where to start.

Thanks, Glee, I followed your suggestion but didn't get any favorable
results.

I powered down, pulled the power cord then removed the RAM stick out
of the DDRII 2 slot then booted and still got the beep.

I then powered down pulled the power cord and removed the RAM stick
from the DDRII 1 slot and replaced it with the one I had removed from
the other slot. Still beeped at me.

I powered down again, pulled the power cord, then put the second RAM
stick into the DDRII 2 slot. This had the two RAM sticks switched
around from their original positions. Still got the beep.

Something I noticed...the CPU cooling fan seems to be erratic. That is
it will start running as soon as I click the switch to boot up, but it
stops then jiggles intermittently when the beep sound occurs. After
the beep sound, this fan starts running normally without further
interruption. Could this mean that the CPU has failed?


It's hard to say, Gordon....it could be the power supply, or the mobo or
the CPU too.

Have you removed all the peripherals and cards except video, re-seated
absolutely everything, and tried again?

Try with the optical drives disconnected and only the hard drive
connected (and floppy drive if you have one).
Try with only the floppy drives connected if one is installed.
Try with NO drives connected.

A single long beep *usually* does not indicate a display problem.
This is a long beep, not the short beep one often hears during a normal
start-up, yes?

It's a slow process of re-seating, and disconnecting/reconnecting
everything to see if you get different behaviour...namely, if you can
get anything on the screen.

Does this have integrated video, or a separate video card?

If I had to make a total guess, I'd bet on a power supply problem. Do
you have a simple power supply tester, or a spare PSU you can try?

ATX PSU Tester
http://www.buy.com/prod/startech-com...202973591.html
and
http://www.amazon.com/StarTech-PSUTE.../dp/B000HVFBX8

I've gone through the process of removing and re-installing all the
add-in cards and interconnection cables. This didn't produce any
noticeable changes other than the CPU fan now runs in short bursts of
about 2 or 3 seconds whereas it was just jiggling like it was starting
to run but never actually rotated the fan.

To answer another question...I do have an nVidia e-GeForce 7600 GS
graphics card installed. This is a 512 MB PCI-E video card. I'm not
using the motherboard's graphics output.

I've not yet tested the power supply (PC Power & Cooling Silencer 470
ATX 12V, Ver 2.2), but it seems to be working okay in that all the
drive activity lights blink on and I can hear the drives spin up and
the read/write arms move.

I'm wondering if maybe the BIOS memory chip or battery has gone bad. I
built this computer in October, 2007. It shouldn't be near the point
of battery failure, I wouldn't think. Also, even if the BIOS battery
is dead, wouldn't the boot CD still work? Should I buy a fresh battery
and do a change-out?

Gordon


  #23  
Old March 1st 10, 01:28 AM posted to microsoft.public.windowsxp.basics
Hot-text
external usenet poster
 
Posts: 239
Default Computer won't boot

BEEP about one second long during the boot process
Pull all the RAM stick out Restart Computer with out RAM stick if the long
BEEP go away it a Bad RAM stick!




"Antares 531" wrote in message
...
On Sun, 28 Feb 2010 12:15:36 -0500, "glee"
wrote:


"Antares 531" wrote in message
. ..
On Sun, 28 Feb 2010 11:04:53 -0500, "glee"
wrote:

"Antares 531" wrote in message
m...
I have an older computer with a Gigabyte GA-P35-DS3L motherboard that
I home-built a few years back. I recently built a new computer and
have been keeping the old one alive until I get the new one all
checked out and settled in.

Yesterday the old computer wouldn't boot. It makes a BEEP about one
second long during the boot process but won't go any farther. The
drive lights flash and the monitor goes through its first sign of
lighting up, after I turn the computer on, but this is as far as it
goes. The monitor goes black and the activity lights on the front of
the computer flash a few times, then everything stops.

I've tried using the original Windows XP Pro installation disk, and
also a second boot disk that I slipstreamed with SP3 on it. Neither
boot disk will initiate a start-up process. The CD drive light
flashes
a few times then quits and nothing more happens after the BEEP.

Any ideas as to what I might try next?

That model mobo apparently has an Award BIOS. One LONG beep from an
Award BIOS often indicates a memory error. I would start by
re-seating
the RAM. If there is more than on stick of RAM try using just one,
then
the other (in the first RAM slot).
If no improvement, try reseating the PCI cards and other items
connected
to the motherboard (power connectors, etc).

It could be other things, but that's where to start.

Thanks, Glee, I followed your suggestion but didn't get any favorable
results.

I powered down, pulled the power cord then removed the RAM stick out
of the DDRII 2 slot then booted and still got the beep.

I then powered down pulled the power cord and removed the RAM stick
from the DDRII 1 slot and replaced it with the one I had removed from
the other slot. Still beeped at me.

I powered down again, pulled the power cord, then put the second RAM
stick into the DDRII 2 slot. This had the two RAM sticks switched
around from their original positions. Still got the beep.

Something I noticed...the CPU cooling fan seems to be erratic. That is
it will start running as soon as I click the switch to boot up, but it
stops then jiggles intermittently when the beep sound occurs. After
the beep sound, this fan starts running normally without further
interruption. Could this mean that the CPU has failed?


It's hard to say, Gordon....it could be the power supply, or the mobo or
the CPU too.

Have you removed all the peripherals and cards except video, re-seated
absolutely everything, and tried again?

Try with the optical drives disconnected and only the hard drive
connected (and floppy drive if you have one).
Try with only the floppy drives connected if one is installed.
Try with NO drives connected.

A single long beep *usually* does not indicate a display problem.
This is a long beep, not the short beep one often hears during a normal
start-up, yes?

It's a slow process of re-seating, and disconnecting/reconnecting
everything to see if you get different behaviour...namely, if you can
get anything on the screen.

Does this have integrated video, or a separate video card?

If I had to make a total guess, I'd bet on a power supply problem. Do
you have a simple power supply tester, or a spare PSU you can try?

ATX PSU Tester
http://www.buy.com/prod/startech-com...202973591.html
and
http://www.amazon.com/StarTech-PSUTE.../dp/B000HVFBX8

I've gone through the process of removing and re-installing all the
add-in cards and interconnection cables. This didn't produce any
noticeable changes other than the CPU fan now runs in short bursts of
about 2 or 3 seconds whereas it was just jiggling like it was starting
to run but never actually rotated the fan.

To answer another question...I do have an nVidia e-GeForce 7600 GS
graphics card installed. This is a 512 MB PCI-E video card. I'm not
using the motherboard's graphics output.

I've not yet tested the power supply (PC Power & Cooling Silencer 470
ATX 12V, Ver 2.2), but it seems to be working okay in that all the
drive activity lights blink on and I can hear the drives spin up and
the read/write arms move.

I'm wondering if maybe the BIOS memory chip or battery has gone bad. I
built this computer in October, 2007. It shouldn't be near the point
of battery failure, I wouldn't think. Also, even if the BIOS battery
is dead, wouldn't the boot CD still work? Should I buy a fresh battery
and do a change-out?

Gordon


  #24  
Old March 1st 10, 01:58 AM posted to microsoft.public.windowsxp.basics
Brian A.
external usenet poster
 
Posts: 2,079
Default Computer won't boot

"Antares 531" wrote in message

On Sun, 28 Feb 2010 16:57:56 -0600, "Unknown"
wrote:

Try the process of elimination if you don't know the beep codes. I.E.
Remove a memory module and try to boot.
Then remove another item and try to boot.

I tried that earlier today but didn't get any positive results. I
removed the #2 memory stick and tried booting...same long beep.

Next I removed both memory sticks and tried to boot but still got the
beep.

Then I removed the #1 memory stick and replaced it with what had
previously been the #2 memory stick and again it beeped at me.

Then I replaced both memory sticks in reverse position from their
original positions. This also got the beep sound.

I disconnected all the hard drives, CD and floppy then booted but
still got the beep.

I just noticed that the keyboard and mouse are not showing any life.
Earlier, the keyboard lights flashed when I booted but now they don't.

The hard drives, CD and floppy drive all seem to be working to the
point that I can hear the hard drives humming and if I put a CD in the
drive the activity light will blink and it seems to be trying to read
the CD. Same for the floppy drive.

I'm thinking that since I got the new computer up and running I've
left this old computer turned off for extended times and this may have
depleted what was left of the BIOS CMOS battery. If this battery went
completely dead the BIOS may not be working at all. I'll buy a new
battery tomorrow and see if that makes any difference. Start with the
little things and work my way up, I guess.

Gordon


If the CMOS battery is failing you should get an error during boot prompting you
to enter setup or continue, doubtful it's the CMOS battery although stranger
things do happen.

A simple way to check if the PS is the cause without purchasing another, simply
place your two PCs side by side, disconnect all of the power connectors from the
new machine and connect the ones needed in the old. If the issue isn't resolved
you can rule out the PS as the cause.

--

Brian A. Sesko
Conflicts start where information lacks.
http://basconotw.mvps.org/

Suggested posting do's/don'ts: http://members.shaw.ca/dts-l/goodpost.htm
How to ask a question: http://support.microsoft.com/kb/555375



  #25  
Old March 1st 10, 03:51 AM posted to microsoft.public.windowsxp.basics
glee
external usenet poster
 
Posts: 1,794
Default Computer won't boot

"Antares 531" wrote in message
...

I've gone through the process of removing and re-installing all the
add-in cards and interconnection cables. This didn't produce any
noticeable changes other than the CPU fan now runs in short bursts of
about 2 or 3 seconds whereas it was just jiggling like it was starting
to run but never actually rotated the fan.

To answer another question...I do have an nVidia e-GeForce 7600 GS
graphics card installed. This is a 512 MB PCI-E video card. I'm not
using the motherboard's graphics output.

I've not yet tested the power supply (PC Power & Cooling Silencer 470
ATX 12V, Ver 2.2), but it seems to be working okay in that all the
drive activity lights blink on and I can hear the drives spin up and
the read/write arms move.

I'm wondering if maybe the BIOS memory chip or battery has gone bad. I
built this computer in October, 2007. It shouldn't be near the point
of battery failure, I wouldn't think. Also, even if the BIOS battery
is dead, wouldn't the boot CD still work? Should I buy a fresh battery
and do a change-out?

Gordon


What happens if you connect your monitor to the onboard video outlet
instead of the video card?

If the CMOS battery was dead, you would still get video, directing you
to BIOS setup to reset everything.

The fact that your drives spin doesn't necessarily mean your PSU is OK.
--
Glen Ventura, MS MVP Oct. 2002 - Sept. 2009
A+
http://dts-l.net/

  #26  
Old March 1st 10, 03:51 AM posted to microsoft.public.windowsxp.basics
glee
external usenet poster
 
Posts: 1,794
Default Computer won't boot

"Antares 531" wrote in message
...

I've gone through the process of removing and re-installing all the
add-in cards and interconnection cables. This didn't produce any
noticeable changes other than the CPU fan now runs in short bursts of
about 2 or 3 seconds whereas it was just jiggling like it was starting
to run but never actually rotated the fan.

To answer another question...I do have an nVidia e-GeForce 7600 GS
graphics card installed. This is a 512 MB PCI-E video card. I'm not
using the motherboard's graphics output.

I've not yet tested the power supply (PC Power & Cooling Silencer 470
ATX 12V, Ver 2.2), but it seems to be working okay in that all the
drive activity lights blink on and I can hear the drives spin up and
the read/write arms move.

I'm wondering if maybe the BIOS memory chip or battery has gone bad. I
built this computer in October, 2007. It shouldn't be near the point
of battery failure, I wouldn't think. Also, even if the BIOS battery
is dead, wouldn't the boot CD still work? Should I buy a fresh battery
and do a change-out?

Gordon


What happens if you connect your monitor to the onboard video outlet
instead of the video card?

If the CMOS battery was dead, you would still get video, directing you
to BIOS setup to reset everything.

The fact that your drives spin doesn't necessarily mean your PSU is OK.
--
Glen Ventura, MS MVP Oct. 2002 - Sept. 2009
A+
http://dts-l.net/

  #27  
Old March 1st 10, 11:10 AM posted to microsoft.public.windowsxp.basics
Brian A.
external usenet poster
 
Posts: 2,079
Default Computer won't boot

"Antares 531" wrote in message

On Sun, 28 Feb 2010 16:57:56 -0600, "Unknown"
wrote:

Try the process of elimination if you don't know the beep codes. I.E.
Remove a memory module and try to boot.
Then remove another item and try to boot.

I tried that earlier today but didn't get any positive results. I
removed the #2 memory stick and tried booting...same long beep.

Next I removed both memory sticks and tried to boot but still got the
beep.

Then I removed the #1 memory stick and replaced it with what had
previously been the #2 memory stick and again it beeped at me.

Then I replaced both memory sticks in reverse position from their
original positions. This also got the beep sound.

I disconnected all the hard drives, CD and floppy then booted but
still got the beep.

I just noticed that the keyboard and mouse are not showing any life.
Earlier, the keyboard lights flashed when I booted but now they don't.

The hard drives, CD and floppy drive all seem to be working to the
point that I can hear the hard drives humming and if I put a CD in the
drive the activity light will blink and it seems to be trying to read
the CD. Same for the floppy drive.

I'm thinking that since I got the new computer up and running I've
left this old computer turned off for extended times and this may have
depleted what was left of the BIOS CMOS battery. If this battery went
completely dead the BIOS may not be working at all. I'll buy a new
battery tomorrow and see if that makes any difference. Start with the
little things and work my way up, I guess.

Gordon


If the CMOS battery is failing you should get an error during boot prompting you
to enter setup or continue, doubtful it's the CMOS battery although stranger
things do happen.

A simple way to check if the PS is the cause without purchasing another, simply
place your two PCs side by side, disconnect all of the power connectors from the
new machine and connect the ones needed in the old. If the issue isn't resolved
you can rule out the PS as the cause.

--

Brian A. Sesko
Conflicts start where information lacks.
http://basconotw.mvps.org/

Suggested posting do's/don'ts: http://members.shaw.ca/dts-l/goodpost.htm
How to ask a question: http://support.microsoft.com/kb/555375



  #28  
Old March 1st 10, 02:27 PM posted to microsoft.public.windowsxp.basics
Antares 531[_2_]
external usenet poster
 
Posts: 385
Default Computer won't boot

On Sun, 28 Feb 2010 18:58:47 -0600, "Brian A."
gonefish'n@afarawaylake wrote:

"Antares 531" wrote in message


(snip)

I'm thinking that since I got the new computer up and running I've
left this old computer turned off for extended times and this may have
depleted what was left of the BIOS CMOS battery. If this battery went
completely dead the BIOS may not be working at all. I'll buy a new
battery tomorrow and see if that makes any difference. Start with the
little things and work my way up, I guess.

Gordon


If the CMOS battery is failing you should get an error during boot prompting you
to enter setup or continue, doubtful it's the CMOS battery although stranger
things do happen.

A simple way to check if the PS is the cause without purchasing another, simply
place your two PCs side by side, disconnect all of the power connectors from the
new machine and connect the ones needed in the old. If the issue isn't resolved
you can rule out the PS as the cause.

I see what you mean, Brian, but I'm a bit reticent to mess with the
new computer and risk causing some serious problems with it.

How long should the CMOS battery last. This one was installed in the
motherboard when I bought it in November 2007. It may have been
installed quite a while before I bought the motherboard, if this item
laid on the shelf somewhere.

I'm thinking it would be prudent to start with the small things like
the CMOS battery and if that doesn't produce any improvement, move on
to something else.

Gordon
  #29  
Old March 1st 10, 02:27 PM posted to microsoft.public.windowsxp.basics
Antares 531[_2_]
external usenet poster
 
Posts: 385
Default Computer won't boot

On Sun, 28 Feb 2010 18:58:47 -0600, "Brian A."
gonefish'n@afarawaylake wrote:

"Antares 531" wrote in message


(snip)

I'm thinking that since I got the new computer up and running I've
left this old computer turned off for extended times and this may have
depleted what was left of the BIOS CMOS battery. If this battery went
completely dead the BIOS may not be working at all. I'll buy a new
battery tomorrow and see if that makes any difference. Start with the
little things and work my way up, I guess.

Gordon


If the CMOS battery is failing you should get an error during boot prompting you
to enter setup or continue, doubtful it's the CMOS battery although stranger
things do happen.

A simple way to check if the PS is the cause without purchasing another, simply
place your two PCs side by side, disconnect all of the power connectors from the
new machine and connect the ones needed in the old. If the issue isn't resolved
you can rule out the PS as the cause.

I see what you mean, Brian, but I'm a bit reticent to mess with the
new computer and risk causing some serious problems with it.

How long should the CMOS battery last. This one was installed in the
motherboard when I bought it in November 2007. It may have been
installed quite a while before I bought the motherboard, if this item
laid on the shelf somewhere.

I'm thinking it would be prudent to start with the small things like
the CMOS battery and if that doesn't produce any improvement, move on
to something else.

Gordon
  #30  
Old March 1st 10, 02:30 PM posted to microsoft.public.windowsxp.basics
Antares 531[_2_]
external usenet poster
 
Posts: 385
Default Computer won't boot

On Sun, 28 Feb 2010 21:51:54 -0500, "glee"
wrote:

"Antares 531" wrote in message
.. .

I've gone through the process of removing and re-installing all the
add-in cards and interconnection cables. This didn't produce any
noticeable changes other than the CPU fan now runs in short bursts of
about 2 or 3 seconds whereas it was just jiggling like it was starting
to run but never actually rotated the fan.

To answer another question...I do have an nVidia e-GeForce 7600 GS
graphics card installed. This is a 512 MB PCI-E video card. I'm not
using the motherboard's graphics output.

I've not yet tested the power supply (PC Power & Cooling Silencer 470
ATX 12V, Ver 2.2), but it seems to be working okay in that all the
drive activity lights blink on and I can hear the drives spin up and
the read/write arms move.

I'm wondering if maybe the BIOS memory chip or battery has gone bad. I
built this computer in October, 2007. It shouldn't be near the point
of battery failure, I wouldn't think. Also, even if the BIOS battery
is dead, wouldn't the boot CD still work? Should I buy a fresh battery
and do a change-out?

Gordon


What happens if you connect your monitor to the onboard video outlet
instead of the video card?

If the CMOS battery was dead, you would still get video, directing you
to BIOS setup to reset everything.

The fact that your drives spin doesn't necessarily mean your PSU is OK.

I haven't tried the on-board video outlet but it does sound like
something worth checking out. If I can get my head on straight later
this morning I'll do this. I'm down with a severe cold and not feeling
up to much in the way of stress.

Gordon
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off






All times are GMT +1. The time now is 09:32 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 PCbanter.
The comments are property of their posters.