If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Rate Thread | Display Modes |
#1
|
|||
|
|||
Why doesn't Windows 10 automatically set my ip address to 192.168.1.10 when I boot?
Why doesn't Windows 10 automatically set my gateway to 192.168.1.1 after I
reboot. https://ibb.co/VTxMMdX Every time I reboot, I get the little yellow in the corner on my "network internet access" task bar icon, which reminds me I have to manually add the gateway of 192.168.1.1 and then everything works until the next reboot. route add 0.0.0.0 mask 0.0.0.0 192.168.1.1 This is "Ethernet Properties" "Internet Protocol Version 4 (TCP/IPv4)" in Control Panel\Network and Internet\Network Connections\Ethernet Network https://ibb.co/VTxMMdX |
Ads |
#2
|
|||
|
|||
Why doesn't Windows 10 automatically set my ip address to192.168.1.10 when I boot?
On 3/6/19 10:38 PM, Freelance Writer wrote:
Why doesn't Windows 10 automatically set my gateway to 192.168.1.1 after I reboot.Â*Â*Â* https://ibb.co/VTxMMdX Every time I reboot, I get the little yellow in the corner on my "network internet access" task bar icon, which reminds me I have to manually add the gateway of 192.168.1.1 and then everything works until the next reboot. route add 0.0.0.0 mask 0.0.0.0 192.168.1.1 This is "Ethernet Properties" "Internet Protocol Version 4 (TCP/IPv4)"Â* in Control Panel\Network and Internet\Network Connections\Ethernet Network https://ibb.co/VTxMMdX Got a spare router? Replace it. Or add one to your current router. You don't have to get fancy, just see if the new router solves the issue, and if so call your ISP. |
#3
|
|||
|
|||
Why doesn't Windows 10 automatically set my ip address to 192.168.1.10when I boot?
Freelance Writer wrote:
Why doesn't Windows 10 automatically set my gateway to 192.168.1.1 after I reboot. https://ibb.co/VTxMMdX Every time I reboot, I get the little yellow in the corner on my "network internet access" task bar icon, which reminds me I have to manually add the gateway of 192.168.1.1 and then everything works until the next reboot. route add 0.0.0.0 mask 0.0.0.0 192.168.1.1 This is "Ethernet Properties" "Internet Protocol Version 4 (TCP/IPv4)" in Control Panel\Network and Internet\Network Connections\Ethernet Network https://ibb.co/VTxMMdX So as expected, you're going "static" according to your two pictures. Then, you neglected, in the Gateway Metric +-----+ | Add | +-----+ to click the Add and add 192.168.1.1 ? You're very close to having a working setup. There's a little background on the Metric value, here. If it will accept the Auto tick box, maybe that will be good enough for a simple desktop situation. https://support.microsoft.com/en-ca/...or-ipv4-routes ******* I googled this a bit, and kept getting Static hits, but it wasn't until Al posted, I realized you really were going Static, and this wasn't a DHCP problem. When you go Static, usually there are some rules about where in the pool, it's best to put such things. (Depends on whether the Router has explicit support for Static - if not, then a Static value should be outside the DHCP range.) Perhaps Char has some suggestions. Since I don't use Static, I don't have the experience. I'm a free-range DHCP user :-) Paul |
#4
|
|||
|
|||
Why doesn't Windows 10 automatically set my ip address to 192.168.1.10 when I boot?
On Wed, 6 Mar 2019 21:38:25 -0600, Freelance Writer
wrote: Why doesn't Windows 10 automatically set my gateway to 192.168.1.1 after I reboot. https://ibb.co/VTxMMdX route add 0.0.0.0 mask 0.0.0.0 192.168.1.1 Since you're trying to add the gateway via a "route add" command and you want it to survive reboots, you need to add the -p argument to make your command persistent, as in: route -p add 0.0.0.0 mask 0.0.0.0 192.168.1.1 But see below for better way. You simply have an incomplete configuration. Every time I reboot, I get the little yellow in the corner on my "network internet access" task bar icon, which reminds me I have to manually add the gateway of 192.168.1.1 and then everything works until the next reboot. This is "Ethernet Properties" "Internet Protocol Version 4 (TCP/IPv4)" in Control Panel\Network and Internet\Network Connections\Ethernet Network https://ibb.co/VTxMMdX On the IPv4 Properties dialog, you forgot to add the default gateway. It's blank in your screen capture. If you add 192.168.1.1 as the default gateway there and OK your way out, you won't have to bother with the "route add" command anymore. |
#5
|
|||
|
|||
Why doesn't Windows 10 automatically set my ip address to 192.168.1.10 when I boot?
On Wed, 6 Mar 2019 23:11:22 -0500, Big Al wrote:
On 3/6/19 10:38 PM, Freelance Writer wrote: Why doesn't Windows 10 automatically set my gateway to 192.168.1.1 after I reboot.*** https://ibb.co/VTxMMdX Every time I reboot, I get the little yellow in the corner on my "network internet access" task bar icon, which reminds me I have to manually add the gateway of 192.168.1.1 and then everything works until the next reboot. route add 0.0.0.0 mask 0.0.0.0 192.168.1.1 This is "Ethernet Properties" "Internet Protocol Version 4 (TCP/IPv4)"* in Control Panel\Network and Internet\Network Connections\Ethernet Network https://ibb.co/VTxMMdX Got a spare router? Replace it. Or add one to your current router. You don't have to get fancy, just see if the new router solves the issue, and if so call your ISP. He just forgot to configure his default gateway in a way that survives reboots. It's blank (not configured) in his screen cap. |
#6
|
|||
|
|||
Why doesn't Windows 10 automatically set my ip address to 192.168.1.10 when I boot?
"Char Jackson" wrote in message
... On the IPv4 Properties dialog, you forgot to add the default gateway. It's blank in your screen capture. If you add 192.168.1.1 as the default gateway there and OK your way out, you won't have to bother with the "route add" command anymore. As a matter of interest, why have you chosen to get a static IP address by configuring it at the PC, rather than configuring a reserved/bound address at the router? Most modern routers have the ability to "bind" an IP address to a PC's MAC address so DHCP always allocates the same IP address rather than one at random whenever the PC and router are rebooted. The advantage with doing the address allocation at the server is that if you ever connect the PC to another network (more of a problem with a laptop or phone than with an "immovable" desktop) you will still get a valid IP address, with no risk of accidentally colliding with one that the other router's DHCP allocates to someone else, or if your own subnet 192.168.1.x happens to be different to the subnet used by the other router: some use 192.168.0.x or 192.168.2.x etc. If the PC is never going to be connected to another network, there's no need to change what presumably works well once you set the gateway address. My network is a mix of the two, as I discovered when my ISP sent me a new router. I'd forgotten that I'd set up reserved addresses for my PCs and Raspberry Pi, but configured my printer and security cameras with static addresses at those devices. Not sure why I wasn't consistent ;-) One thing to be wary of with a static IP address configured at the computer. You probably know this, but I'll mention it just in case... Make sure that any static addresses are in the same subnet (eg 192.168.1.x) but *outside* the range of addresses (the "scope") that DHCP hands out. You don't want the router to hand out the same address that you've statically allocated to the PC. My router (BT Hub One) uses 192.168.1.x with a netmask of 255.255.255.0, so all the addresses .1 - .254 are in the subnet, but the scope is 192.168.1.65-255, leaving the first 64 addresses free for static addresses. |
#7
|
|||
|
|||
Why doesn't Windows 10 automatically set my ip address to 192.168.1.10 when I boot?
"Freelance Writer" wrote in message ...
Why doesn't Windows 10 automatically set my gateway to 192.168.1.1 after I reboot. https://ibb.co/VTxMMdX Every time I reboot, I get the little yellow in the corner on my "network internet access" task bar icon, which reminds me I have to manually add the gateway of 192.168.1.1 and then everything works until the next reboot. route add 0.0.0.0 mask 0.0.0.0 192.168.1.1 This is "Ethernet Properties" "Internet Protocol Version 4 (TCP/IPv4)" in Control Panel\Network and Internet\Network Connections\Ethernet Network https://ibb.co/VTxMMdX Paul has correctly answered why you are repeatedly asked for the default gateway. Enter it (the center screen) in the Default gateway box. In addition, and I'm assuming you are using your ISP's DNS servers addresses in your router settings. Apparently they work okay but I would add an Alternative DNS server address like 8.8.4.4 (Google's DNS server) in case there's a problem with your ISP right below the Default gateway setting. It's good to have an alternative DNS server even though you probably have your two ISP server addresses in the router. -- Bob S. |
Thread Tools | |
Display Modes | Rate This Thread |
|
|