If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
What WinXP command proves USB drivers are installed and working?
What WinXP command proves USB drivers are installed and working?
I have never rooted an Android phone but I plan on doing so. Therefore, I went through the motions and wrote up the instructions below. About 95% of what I wrote below comes from the first URL. But I modified it to clarify where I was confused. One place that I need to further clarify is that I need to tell people HOW to prove that they have the necessary "usb drivers" on Windows XP. Hence my question above: Q: What WinXP command proves USB drivers are installed and working? ----------------------------------------------------------------- NOTE: Below is the work in progress rooting tutorial. http://androidcentral.us/2014/04/roo...ung-galaxy-s3/ How to Root T-Mobile Samsung Galaxy S3 (SGH-T999) on Android 4.3 Jelly Bean Firmware Requirements: a. Windows computer with USB drivers installed b. Fully charged T-Mobile Samsung Galaxy S3 SGH-T999 with USB data cable c. CF-Root zip package http://download.chainfire.eu/234/CF-...mo-sght999.zip d. Odin3 v3.09 Flashing Utility (note the version available is 3.10) http://androidcentral.us/2013/11/download-odin/ e. Optional: QuickHash for Windows XP https://sourceforge.net/projects/quickhash/ Phone: 1. Settings More About device (repeatedly tap) Build Number until it says "you are now 4 steps away from being a developer". 2. Tap developer mode 4 more times until it says "you are now a developer". 3. Enable USB debugging on your phone by the following options: Settings More Developer Options Debugging USB debugging (check the box) It will say: Debugging mode launches when USB is connected. Allow USB debugging? USB debugging is intended for development purposes only. It can be used to copy data between your comptuer and your device, install applications on your device without notification, and read log data. Press "OK". NOTE: To turn off developer mode in the futu Settings More Developer options (slide the green slider from ON to OFF) You may need to click "Revoke USB Debugging Authorizations". You may need to go to apps all settings Clear Data. Some say you may need to also do a factory reset. 4. To verify root access later, open the Google Play Store app on your phone and install "Root Checker" by "joey krim". https://play.google.com/store/apps/d...krim.rootcheck Use "Root Checker" to confirm root access. 5. Install Titanium Backup root freewa https://play.google.com/store/apps/d...TitaniumBackup Windows PC: 1. Extract CF-Auto-Root-d2tmo-d2tmo-sght999.zip to its own folder Name: CF-Auto-Root-d2tmo-d2tmo-sght999.zip Size: 17.3 MB (18,147,068 bytes) MD5 Hash: 6BC132736171F96A59ECF5934B7C30BE SHA-1 Hash: 72B4547023003064736BF428305AF102031E15D1 SHA256 Hash: FC0393F86C7A6FD88C3104B09117D6D3C744AEE65F0C339777 2B40E42A1250BF SHA512 Hash: DDF472763717672A1D34C726D0A16D1CEAAEB2F8F34253ECA9 8EC558DE5EFA1CEFCB5E58DF9EC247CCBF6E430DD57A232015 AF57F4917C28571C2441479DC7FD 2. Extract Odin v3.09 files to its own folder NOTE: The only version available is Odin v3.10 which doesn't have a "PDA" button (it has a PIT button instead). Name: Odin v3.10 by Ohguideme.rar Size: 801 KB (820,656 bytes) MD5 Hash: A51C897BF6B317D545110181D4464C3B SHA-1 Hash: 1F1B73FACB01E286C1C73F4675EC97B6E14280E2 SHA256 Hash: 6CE9DB71BE56B4B59CB3171BB8FF16765BD7B66102FE0F3D1A EF2D8C4423D5B7 SHA512 Hash: 633414971EE3D6E672C7407B0AB4A67F95511D341B3336F464 A1A9B4D88634E5D93FF962D7042CAC1847B5949B833A147055 A780499C5002A0512F48044EC13E 3. From the Odin extracted folder run Odin3-v3.o9. 4. Reboot your T-Mobile Galaxy S3 into Download Mode: a. Turn Off Galaxy S3. b. Simultaneously press & hold the three buttons "VolumeDown+Home+Power" until you see a warning on your screen. When you press the buttons, within a couple of seconds, you'll feel a buzz & the green, white, & yellow message comes up: Warning!! A custom OS can cause critical problems in phone and installed applications. If you want to download a custom OS, press the volume up key. Otherwise press the volume down key to cancel. Volume up: Continue Volume down: Cancel (restart phone) c. After the warning, press once the Volume Up button to continue. 5. While in download mode connect your GS3 to PC via the USB data cable. Make sure that Odin3 detects your device. 6. In the Odin GUI, make sure that only "Auto Reboot" & "F. Reset Times" options are checked. (Leave the rest of the options off, which are the default settings). 7. In the Odin GUI, click the PDA button and from the extracted folder select the CF-Rooted kernel file and hit the START to flash the kernel. 8. Wait for Odin3 to complete. 9. When completed, Odin will notify you via the PASS!! message in Odin and at this stage your phone will automatically reboot. 10. Once normally booted, check that SuperSU has been installed. a. Now you have full root access to your phone. b. You can also install apps which require root access. c. You can get rid of the stock apps (using the Titanium Backup app). d. If you?re planning to install a Custom ROM or Mods then you want to install ROM Manager, which will then help you to flash Custom Recovery, TWRP or ClockworkMod, depending on your choice. |
Ads |
#2
|
|||
|
|||
What WinXP command proves USB drivers are installed and working?
Stijn De Jong wrote:
What WinXP command proves USB drivers are installed and working? https://s2.postimg.org/ddmcjzeex/usbflash.gif That does not guarantee that all partitions will mount. Only the first partition of a USB flash will mount in Windows. While Linux will easily allow four partitions to be created. And the Linux ones will all mount in Linux. Paul |
#3
|
|||
|
|||
What WinXP command proves USB drivers are installed and working?
On Tue, 07 Mar 2017 00:00:29 -0500, Paul wrote:
Stijn De Jong wrote: What WinXP command proves USB drivers are installed and working? https://s2.postimg.org/ddmcjzeex/usbflash.gif That does not guarantee that all partitions will mount. Only the first partition of a USB flash will mount in Windows. While Linux will easily allow four partitions to be created. And the Linux ones will all mount in Linux. Thanks for that pointer to the "this device is working properly". http://i.cubeupload.com/F8AiNN.jpg As you are aware, we all have had to troubleshoot devices where that message was displayed, so, I'd normally not put any credence whatsoever into it, unless you're pretty much convinced that this is the best test. Here's what mine says on WinXP SP3: Device Manager Universal Serial Bus Controllers Right click on "USB Mass Storage Device" Properties Device General Device status This device is working properly. http://i.cubeupload.com/F8AiNN.jpg If that's the best we have, then that's what I'll put in the instructions! |
#4
|
|||
|
|||
What WinXP command proves USB drivers are installed and working?
Stijn De Jong wrote:
On Tue, 07 Mar 2017 00:00:29 -0500, Paul wrote: Stijn De Jong wrote: What WinXP command proves USB drivers are installed and working? https://s2.postimg.org/ddmcjzeex/usbflash.gif That does not guarantee that all partitions will mount. Only the first partition of a USB flash will mount in Windows. While Linux will easily allow four partitions to be created. And the Linux ones will all mount in Linux. Thanks for that pointer to the "this device is working properly". http://i.cubeupload.com/F8AiNN.jpg As you are aware, we all have had to troubleshoot devices where that message was displayed, so, I'd normally not put any credence whatsoever into it, unless you're pretty much convinced that this is the best test. Here's what mine says on WinXP SP3: Device Manager Universal Serial Bus Controllers Right click on "USB Mass Storage Device" Properties Device General Device status This device is working properly. http://i.cubeupload.com/F8AiNN.jpg If that's the best we have, then that's what I'll put in the instructions! You can check Disk Management then, and see if a block device is present. A USB flash stick will not show up in File Explorer, until somehow the system discovers it has a file system. Disk Management is one way to examine it. The tools in WinXP aren't all that convenient. It can be difficult to "erase" a USB flash, if you were to copy a hybrid ISO onto the thing with "dd". Don't expect Disk Management to do everything you could ever want. Disk Management GUI and "diskpart" command line, work best with conventional storage devices. USB flash isn't treated quite as well. USB rotating disk drives (enclosures) work a bit better than USB flash. This is related to the status of the RMB bit. Some larger USB flash sticks, actually have the opposite value of RMB, than previous lower-capacity ones. http://www.uwe-sieber.de/usbstick_e.html You are right to ask questions about USB flash, as it's likely to have more issues than other storage choices. And not all desktops can boot from them either. The USB support module has only been in the BIOS for the last 10-12 years or so. My oldest two PCs cannot boot from a USB flash. Paul |
#5
|
|||
|
|||
What WinXP command proves USB drivers are installed and working?
On Tue, 07 Mar 2017 01:09:33 -0500, Paul wrote:
You are right to ask questions about USB flash, as it's likely to have more issues than other storage choices. Thanks Paul for the disk management suggestion to prove that the phone was recognized. http://i.cubeupload.com/Mo5BlN.jpg In my case, the phone was NOT recognized in either the USB method or the DISK method, so, pretty much my conclusion is that my USB port on my phone is kaput. http://i.cubeupload.com/iPWGCb.jpg I haven't used it for a year (I charge the batteries in a separate charger), so, I was just hoping I'd get it to work, but I'm going to root the phone without using a cable. This one-click "Kingoroot" method looks promising for example. https://www.kingoapp.com/ |
#6
|
|||
|
|||
What WinXP command proves USB drivers are installed and working?
Stijn De Jong wrote:
On Tue, 07 Mar 2017 01:09:33 -0500, Paul wrote: You are right to ask questions about USB flash, as it's likely to have more issues than other storage choices. Thanks Paul for the disk management suggestion to prove that the phone was recognized. http://i.cubeupload.com/Mo5BlN.jpg In my case, the phone was NOT recognized in either the USB method or the DISK method, so, pretty much my conclusion is that my USB port on my phone is kaput. http://i.cubeupload.com/iPWGCb.jpg I haven't used it for a year (I charge the batteries in a separate charger), so, I was just hoping I'd get it to work, but I'm going to root the phone without using a cable. This one-click "Kingoroot" method looks promising for example. https://www.kingoapp.com/ Your phone is not a USB Flash key. For general device recognition, use UVCView or USBTreeView. The latter is much easier to find. http://www.uwe-sieber.de/usbtreeview_e.html When USB devices connect, "endpoints" have to be set up so that the config space of the device can be read. If an endpoint forms, and "information" such as USB class comes from the device, that's proof the physical layer (i.e. the port), is working. Just seeing the right-hand pane on USBTreeView populate with the phone info, is proof it is "connected". Phones use MTP, which is not a conventional file system. The phone appears as a "device", rather than as a conventional file system. Operations are done at file level rather than block level. You cannot "format" the phone from the Windows side. But you can read a whole file, write a whole file. The granularity, and where the device appears in GUI interfaces, is different. On WinXP, the MTP driver is delivered via Windows Media Player, as it was intended as a path for loading potentially DRM-protected content into the device. (And in turn, downloading and using the WMP package involves a "Genuine Check".) On later OSes, the MTP driver is an in-box driver. Microsoft decided delivering the MTP driver as "just a driver", wasn't enough. If all devices had been designed with USB Mass Storage, the story would have been a lot simpler and more useful for end-users. (The time required to "get things done" would be less, because it would "just work".) MTP is meant to be a form of hand-cuffs. Paul |
#7
|
|||
|
|||
What WinXP command proves USB drivers are installed and working?
On Tue, 07 Mar 2017 16:31:53 -0500, Paul wrote:
If all devices had been designed with USB Mass Storage, the story would have been a lot simpler and more useful for end-users. (The time required to "get things done" would be less, because it would "just work".) MTP is meant to be a form of hand-cuffs. Thanks Paul. In the end, I just gave up with the USB because my phone is worse than most due to the fact the USB port is kaput (which is apparently common with Samsung S3 phones). I'm not sure what I did since I installed a foreign APK, but it seems to have worked to download an APK to kingoroot using Firefox on the phone. It didn't use Windows, in the end, so this is off topic, but to close the loop, here's what I did (although I'm not sure what 'type' of root a "kingoroot' is in the end). http://i.cubeupload.com/HY1E6B.jpg I downloaded the ZIP installer (which Android calls an "APK" but it's just a zip file): http://i.cubeupload.com/uleVfF.jpg Then I tapped on the zip file (which is equivalent to a Windows doubleclick): http://i.cubeupload.com/Z4uCU6.jpg That installed the "kingoroot" app: http://i.cubeupload.com/GxVyyC.jpg Here is the kingo root app organized in my system folder on my one desktop: http://i.cubeupload.com/XRjvkP.jpg I tapped on that Kingoroot app and this came up: http://i.cubeupload.com/CJlJEg.jpg I pressed the button to root the phone, which took about 90 seconds: http://i.cubeupload.com/9Sd1TC.jpg I started getting scared, but I soon saw a message "root succeeded": http://i.cubeupload.com/nlIV1u.jpg To confirm I had root access, I started a separate root-checker app: http://i.cubeupload.com/9qx4JW.jpg That root checker app confirmed I now had root access: http://i.cubeupload.com/DG7PjD.jpg Then I ran the Titanium Backup free app (which requires root access): http://i.cubeupload.com/OQHqGv.jpg And voila! I can now backup my phone to an sd card, to an internal partition, to a computer, to the cloud, whatever! http://i.cubeupload.com/aVDyfp.jpg Thanks for your help, and I hope this helps others, even though it turned out to be a non-Windows solution that I ended up using (because my phone USB port was bad). |
Thread Tools | |
Display Modes | |
|
|