If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Rate Thread | Display Modes |
#1
|
|||
|
|||
1st partition drive nameing of multiple hdds
Haven't found anything that says win10 improved the drive/partition
designation. i.e. the alpha/drive number of the 1st partition of the hdd is sequential to the previous hdd. e.g. hdd0 has the partition as C:, the 1st partiton on hdd1 is D: then the hdd2 would have E:. Just wonder/hope that I can have a C: & D: on hdd0, then E: & F: on hdd1, etc which would make more sense but m$..... Since I haven't found any more info, guess the partition nameing scheme is the same as the DOS days for internal hard drives?? |
Ads |
#2
|
|||
|
|||
1st partition drive nameing of multiple hdds
On 11/15/2016 04:12 PM, Wolf K wrote:
On 2016-11-15 15:53, lew wrote: Haven't found anything that says win10 improved the drive/partition designation. i.e. the alpha/drive number of the 1st partition of the hdd is sequential to the previous hdd. e.g. hdd0 has the partition as C:, the 1st partiton on hdd1 is D: then the hdd2 would have E:. Just wonder/hope that I can have a C: & D: on hdd0, then E: & F: on hdd1, etc which would make more sense but m$..... Since I haven't found any more info, guess the partition nameing scheme is the same as the DOS days for internal hard drives?? That scheme doesn't allow for multiple partitions on a single HDD. Which is why Windows does it the way it does it. Which is (as you probably know) as follows: Windows assigns "drive" letters in order of creation. That includes optical drives, external drives, and USB-flash drives: the first time Windows detects these, it assigns a drive letter. Problem: thedrive letter for a flash drive is assigned to the port it's connected to. It uses "the next available" letter. So if you Delete partition G, the next partition created will be G. That's why I name all partitions and flash drives, and ignore drive letters. Have a good day, I assign my flash drives starting down about J: I need them to be fixed so scripts work. And I move them from socket to socket and they always stay the same lettering. Even from PC to PC, at least once you reletter them on that PC. Guess I'm just lucky with my hardware :-) |
#3
|
|||
|
|||
1st partition drive nameing of multiple hdds
On Tue, 15 Nov 2016 20:53:03 -0000 (UTC), lew
wrote: Haven't found anything that says win10 improved the drive/partition designation. i.e. the alpha/drive number of the 1st partition of the hdd is sequential to the previous hdd. e.g. hdd0 has the partition as C:, the 1st partiton on hdd1 is D: then the hdd2 would have E:. Just wonder/hope that I can have a C: & D: on hdd0, then E: & F: on hdd1, etc which would make more sense but m$..... Since I haven't found any more info, guess the partition nameing scheme is the same as the DOS days for internal hard drives?? You can go to Disk Management and change the drive letters to whatever you like, except that the drive that you're booted from must stay as it is. So if drive 0 has C and E, while drive 1 has D and F, you can temporarily change D to a higher letter so that D is available to be assigned, then assign D where E is. Finish up by assigning E, which is now available, to the first volume on drive 1. It's really simple once you look around in Disk Management, but holler if you have any questions. If D-E-F are simple data drives, the letter changes should be completely harmless. Famous last words, though, so if you're worried, make a bootable backup first. |
#4
|
|||
|
|||
1st partition drive nameing of multiple hdds
In article
lew wrote: Since I haven't found any more info, guess the partition nameing scheme is the same as the DOS days for internal hard drives?? And your point is what, Einstein? |
#5
|
|||
|
|||
1st partition drive nameing of multiple hdds
In alt.comp.os.windows-10, on Tue, 15 Nov 2016 16:12:10 -0500, Wolf K
wrote: On 2016-11-15 15:53, lew wrote: Haven't found anything that says win10 improved the drive/partition designation. i.e. the alpha/drive number of the 1st partition of the hdd is sequential to the previous hdd. e.g. hdd0 has the partition as C:, the 1st partiton on hdd1 is D: then the hdd2 would have E:. Just wonder/hope that I can have a C: & D: on hdd0, then E: & F: on hdd1, etc which would make more sense but m$..... Since I haven't found any more info, guess the partition nameing scheme is the same as the DOS days for internal hard drives?? That scheme doesn't allow for multiple partitions on a single HDD. Why is that? Which is why Windows does it the way it does it. Which is (as you probably know) as follows: Windows assigns "drive" letters in order of creation. That includes optical drives, external drives, and USB-flash drives: the first time Windows detects these, it assigns a drive letter. Problem: thedrive letter for a flash drive is assigned to the port it's connected to. It uses "the next available" letter. So if you Delete partition G, the next partition created will be G. But since XP, I think it was, you can assign just about any letter you want. (Probably not Greek letters.) Even before then there was a program LetterAssign, or LetAssign or something that let you assign whatever you wanted. It went in autoexec.bat. That's why I name all partitions and flash drives, That's a good idea. and ignore drive letters. Have a good day, |
Thread Tools | |
Display Modes | Rate This Thread |
|
|