If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
UPDATE: WinXP Home Edition HDD to Another PC
Hi,
I have installed WinXP Home Edition on several of my computers without any issues. However, I have not been able to install it on a Global brand desktop. I have tried different schemes, install on a "blank" HDD (hard disk drive), replace/overwrite Win98, etc. Note: I changed the boot sequence to CD rom first when using a "blank" HDD. The problem occurs after files are transferred to the HDD, then a reboot occurs. An endless cycle of rebooting or a shutdown happens. Note: My desktop computers have HDD drawers (I installed). What would happen if I install WinXP on another PC (I will not "activate" yet), remove the drawer/HDD and install it in the Global PC? In other words, would WinXP complain or refuse to bootup? Thank You in advance, John There is yet another way to do this. Ingredients: Working hard drive with two partitions. Floppy drive with MSDOS on it (sys A: in Windows 98) Technician computer, to prepare the hard drive. Procedu 1) Create two FAT32 partitions. C: should be the first partition on the disk, in terms of MBR primary partition entries. If you were to swap the order, the installed OS appears on D: . Ask me how I discovered this :-( +--------------------------+--------------------------------------------+ | FAT32 C: | copy of CD i386 folder, on FAT32 partition | +--------------------------+--------------------------------------------+ 2) Create a MSDOS floppy on the Win98 technician computer. I think that's "sys A:" or so. it's OK if you don't have Win98 computer any more, as long as you have an MSDOS boot floppy that gives the old A: prompt. If desperate, you can get a boot floppy of bootdisk.com or similar. 3) Set boot order to floppy, then hard drive, on the target computer. Bring the hard drive over from the technician computer, with the 5000+ file i386 folder stored on the second partition. You copy the i386 folder, off the installer CD, to fill the second partition. I made my second partition about 1GB in size. 4) Boot the MSDOS floppy. CD to D:\i386. You will notice two setup programs. One is suited to this installation, the other is not. Try them, until the installation window appears. 5) I think on the reboot, you remove the MSDOS floppy, as by that time, the necessary contents of i386 have been copied over to C:, the boot flag has been set on the first partition, the MBR boot code loaded and so on. The installation will then continue, referencing D: as the source of any additional files. The purpose of that procedure, is to avoid the usage of a CD at all. The disadvantage of the approach, is C: ends up as FAT32. While you can use the "convert" command to convert FAT32 to NTFS, the conversion block size is too small for efficient operation. There's probably a few more steps you could throw in, to fix that. But this post is crazy enough as it is :-) I installed the WinXP on my current computer, using the above method. (I did it "just for fun".) On my MSDOS floppy, I included smartdrv as a caching software. The time taken to research smartdrv, test it, I could have finished the install. Without smartdrv, the partition to partition file copying, happens at a rate of one file per second. Just walk away and check back every once in a while, to see how it's going. It'll probably take a couple hours, if you don't have smartdrv loaded. There are other floppy sets you can use for this job, but when I tried one of them, it just didn't work. So I tried the MSDOS bootstrap procedure instead. And I eventually got it to work. HTH, Paul Hi Paul, UPDATE: I used a 10G HDD and partitioned it with about 1G for D:. Using a HDD docking (USB) station in another PC, I copied "i386" folder from the WinXP's OS CD rom to that partition (D in the 10G IDE HDD connected to the docking station. Afterwards, I removed the HDD and placed it in the drawer and put it in the Global PC. After using a floppy boot disk in A:, I entered "i386" directory/folder and launched "WINNT" (I tried some others first). This started the installation process. Everything started fine and it took a long time to transfer system files between the two partitions due to the lateral head movements. I removed the bootable floppy (prompted to do so). It looked like this method was going to work, but here we go again, the rebooting started again and again, then shut down. In every failure there is a lesson learned, and I learned this problem has nothing to do with the CD rom drive. I also learned a method to install WinXP on a laptop's HDD if the laptop has a defective DVD/CD drive. Thanks again for your technique, John |
Ads |
#2
|
|||
|
|||
Just 9 Gb partitioned for WinXP Home Edition sp3 "You Need more "
wrote in message ...
Hi, Hi Paul, UPDATE: I used a 10G HDD and partitioned it with about 1G for D:. Just 9 Gb partitioned for XP sp3 OS Need a good 60 Gb or more Using a HDD docking (USB) station in another PC, I copied "i386" folder from the WinXP's OS CD rom to that partition (D in the 10G IDE HDD connected to the docking station. Afterwards, I removed the HDD and placed it in the drawer and put it in the Global PC. After using a floppy boot disk in A:, I entered "i386" directory/folder and launched "WINNT" (I tried some others first). This started the installation process. Everything started fine and it took a long time to transfer system files between the two partitions due to the lateral head movements. I removed the bootable floppy (prompted to do so). It looked like this method was going to work, but here we go again, the rebooting started again and again, then shut down. In every failure there is a lesson learned, and I learned this problem has nothing to do with the CD rom drive. I also learned a method to install WinXP on a laptop's HDD if the laptop has a defective DVD/CD drive. You have to unplug the laptop's Defective DVD/CD drive first In BOS setup F2 for HP Thanks again for your technique, John Paul Knows how unplug the laptop's drive Work with him he a good Tech.... |
#3
|
|||
|
|||
UPDATE: WinXP Home Edition HDD to Another PC
|
Thread Tools | |
Display Modes | |
|
|