A Windows XP help forum. PCbanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » PCbanter forum » Microsoft Windows 8 » Windows 8 Help Forum
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Win 8 not offering to fix external USB drive file system



 
 
Thread Tools Rating: Thread Rating: 2 votes, 5.00 average. Display Modes
  #1  
Old January 25th 14, 08:24 AM posted to alt.comp.os.windows-8
Brighty
external usenet poster
 
Posts: 4
Default Win 8 not offering to fix external USB drive file system

I have a USB 2.0 WD My Passport Essential SE drive which I use with my Win 7
laptop. I always ignored a prompt on every USB plug in to repair the file system
as it worked fine. But my new Win 8 PC refuses to see it in File Explorer, it
appears and disappears constantly, playing the four tone chime over and over. So
I repaired its file system on the Win 7 machine and now it starts without
complaint there, but still no luck in Win 8. The Win 8 PC offered to repair it
once, and I accepted but it stopped a third of the way through, and Win 8 now no
longer offers to repair.

I have the latest 64 bit WD driver on the Win 8 PC, using different USB slots
make no difference. I've tried a new USB cable which is good with other
peripherals. I have a lot of data on the drive, so a reformat is not on the
table. I have another external USB 2.0 drive which loads in Win 8 with no
difficulty.

Is Win 8 so fussy? Any help will be appreciated, I can raise it with WD, but I'm
not sure that it's a drive problem.


Properties as shown in Win 8:
Device
USBSTOR\Disk&Ven_WD&Prod_My_Passport_071A&Rev_2019 \57584A314137304832383737&0
was configured.

Driver Name: disk.inf
Class GUID: {4D36E967-E325-11CE-BFC1-08002BE10318}
Driver Date: 06/21/2006
Driver Version: 6.2.9200.16384
Driver Provider: Microsoft
Driver Section: disk_install.NT
Driver Rank: 0xFF0006
Matching Device ID: GenDisk
Outranked Drivers: disk.inf:GenDisk:00FF2002
Device Updated: false



Thanks
John







--
--------------------------------- --- -- -
Posted with NewsLeecher v6.5 Beta 2
Web @ http://www.newsleecher.com/?usenet
------------------- ----- ---- -- -

Ads
  #2  
Old January 25th 14, 09:33 AM posted to alt.comp.os.windows-8
Paul
external usenet poster
 
Posts: 18,275
Default Win 8 not offering to fix external USB drive file system

Brighty wrote:
I have a USB 2.0 WD My Passport Essential SE drive which I use with my Win 7
laptop. I always ignored a prompt on every USB plug in to repair the file system
as it worked fine. But my new Win 8 PC refuses to see it in File Explorer, it
appears and disappears constantly, playing the four tone chime over and over. So
I repaired its file system on the Win 7 machine and now it starts without
complaint there, but still no luck in Win 8. The Win 8 PC offered to repair it
once, and I accepted but it stopped a third of the way through, and Win 8 now no
longer offers to repair.

I have the latest 64 bit WD driver on the Win 8 PC, using different USB slots
make no difference. I've tried a new USB cable which is good with other
peripherals. I have a lot of data on the drive, so a reformat is not on the
table. I have another external USB 2.0 drive which loads in Win 8 with no
difficulty.

Is Win 8 so fussy? Any help will be appreciated, I can raise it with WD, but I'm
not sure that it's a drive problem.

Properties as shown in Win 8:
Device
USBSTOR\Disk&Ven_WD&Prod_My_Passport_071A&Rev_2019 \57584A314137304832383737&0
was configured.

Driver Name: disk.inf
Class GUID: {4D36E967-E325-11CE-BFC1-08002BE10318}
Driver Date: 06/21/2006
Driver Version: 6.2.9200.16384
Driver Provider: Microsoft
Driver Section: disk_install.NT
Driver Rank: 0xFF0006
Matching Device ID: GenDisk
Outranked Drivers: disk.inf:GenDisk:00FF2002
Device Updated: false

Thanks
John


A few observations:

1) This could be a 2.5 inch drive, drawing all hard
drive power from the USB bus.
2) Excessive drive power consumption, will cause the
bus voltage to drop, the drive to spin down and spin up
again, you get "chimes" when the drive is detected again.
If that happens in the middle of CHKDSK, you're in trouble.
3) You need to ensure it isn't a power problem.

USB2 limits bus power to 500mA. Depending on the computer
type (laptop or desktop), the electrical circuit isn't nearly
as stingy as the specification suggests. Some of them, you
can draw 1000mA, before the self-resetting fuse opens up.

If you were to read the specs for the internal drive mechanism
itself, some of those draw 1000mA during spinup, then much
less current when in steady state. And that means, spec-wise,
we're in limbo. A few of the drives are at 500mA max, and
those are less likely to be an issue.

To see if this is a drive problem, you could remove it
from the casing. Some of these pre-packaged drives from
WD and Seagate, the packaging is designed to thwart easy
removal. If I need to "remove an enclosure" from the equation,
pulling the drive and connecting it to my desktop
SATA cabling, allows testing the drive directly.

*******

Another observation for you, is portable storage encourages
aggressive spin-down policies. That means the product has
internal settings, telling it to spin down after five seconds
of dis-use. This is hard on the drive, if done with aggression.
It is frequently used as a "cooling" solution, so the drive
can be sealed right up, and still remain cool.

The drive mechanism itself could be failing. And then it would
be hard to tell apart the various kinds of possible faults.

Now, if the computer had USB3 ports (powder blue plastic), you
were using Windows 8 USB3 drivers, I might believe it to be a
driver problem of some sort. If on the other hand, everything
in that path is USB2, a much older driver might be involved
(proven code and architecture), and Microsoft would be
"off the hook". I've heard a few complaints, when comparing
the third-party USB3 drivers, to the Microsoft driver for USB3,
so that's a possibility. But the root of the
problem just as easily, could be a non-reliable power problem,
or a drive mechanism about to fail. Perhaps if all the
OS observations were done on exactly the same computer
hardware, we could eliminate the bus power as an issue.
But if comparing two different computers, anything is
possible.

It's too bad these products, don't have an indicator light
to warn us of power problems. It's sure not a technology problem.
Just a lack of imagination.

Paul
  #3  
Old January 25th 14, 03:54 PM posted to alt.comp.os.windows-8
Brighty
external usenet poster
 
Posts: 4
Default Win 8 not offering to fix external USB drive file system

In reply to "Paul" who wrote the following:

Brighty wrote:
I have a USB 2.0 WD My Passport Essential SE drive which I use with my Win 7
laptop. I always ignored a prompt on every USB plug in to repair the file
system
as it worked fine. But my new Win 8 PC refuses to see it in File Explorer,
it
appears and disappears constantly, playing the four tone chime over and
over. So
I repaired its file system on the Win 7 machine and now it starts without
complaint there, but still no luck in Win 8. The Win 8 PC offered to repair
it
once, and I accepted but it stopped a third of the way through, and Win 8
now no
longer offers to repair.

I have the latest 64 bit WD driver on the Win 8 PC, using different USB
slots
make no difference. I've tried a new USB cable which is good with other
peripherals. I have a lot of data on the drive, so a reformat is not on the
table. I have another external USB 2.0 drive which loads in Win 8 with no
difficulty.

Is Win 8 so fussy? Any help will be appreciated, I can raise it with WD, but
I'm
not sure that it's a drive problem.

Properties as shown in Win 8:
Device
USBSTOR\Disk&Ven_WD&Prod_My_Passport_071A&Rev_2019 \57584A314137304832383737&
0
was configured.

Driver Name: disk.inf
Class GUID: {4D36E967-E325-11CE-BFC1-08002BE10318}
Driver Date: 06/21/2006
Driver Version: 6.2.9200.16384
Driver Provider: Microsoft
Driver Section: disk_install.NT
Driver Rank: 0xFF0006
Matching Device ID: GenDisk
Outranked Drivers: disk.inf:GenDisk:00FF2002
Device Updated: false

Thanks
John


A few observations:

1) This could be a 2.5 inch drive, drawing all hard
drive power from the USB bus.
2) Excessive drive power consumption, will cause the
bus voltage to drop, the drive to spin down and spin up
again, you get "chimes" when the drive is detected again.
If that happens in the middle of CHKDSK, you're in trouble.
3) You need to ensure it isn't a power problem.

USB2 limits bus power to 500mA. Depending on the computer
type (laptop or desktop), the electrical circuit isn't nearly
as stingy as the specification suggests. Some of them, you
can draw 1000mA, before the self-resetting fuse opens up.

If you were to read the specs for the internal drive mechanism
itself, some of those draw 1000mA during spinup, then much
less current when in steady state. And that means, spec-wise,
we're in limbo. A few of the drives are at 500mA max, and
those are less likely to be an issue.

To see if this is a drive problem, you could remove it
from the casing. Some of these pre-packaged drives from
WD and Seagate, the packaging is designed to thwart easy
removal. If I need to "remove an enclosure" from the equation,
pulling the drive and connecting it to my desktop
SATA cabling, allows testing the drive directly.

*******

Another observation for you, is portable storage encourages
aggressive spin-down policies. That means the product has
internal settings, telling it to spin down after five seconds
of dis-use. This is hard on the drive, if done with aggression.
It is frequently used as a "cooling" solution, so the drive
can be sealed right up, and still remain cool.

The drive mechanism itself could be failing. And then it would
be hard to tell apart the various kinds of possible faults.

Now, if the computer had USB3 ports (powder blue plastic), you
were using Windows 8 USB3 drivers, I might believe it to be a
driver problem of some sort. If on the other hand, everything
in that path is USB2, a much older driver might be involved
(proven code and architecture), and Microsoft would be
"off the hook". I've heard a few complaints, when comparing
the third-party USB3 drivers, to the Microsoft driver for USB3,
so that's a possibility. But the root of the
problem just as easily, could be a non-reliable power problem,
or a drive mechanism about to fail. Perhaps if all the
OS observations were done on exactly the same computer
hardware, we could eliminate the bus power as an issue.
But if comparing two different computers, anything is
possible.

It's too bad these products, don't have an indicator light
to warn us of power problems. It's sure not a technology problem.
Just a lack of imagination.

Paul


Hello Pauk,

Thanks for the thoughtful reply. The Win 8 machine is a Sony Fit i7 with two USB
3.0 ports, I've tried both, and one is a charging port so I'll rule out a power
supply issue. The drive works faultlessly streaming video to a Merlin jukebox
style unit which also doesn't power it.

Heavy file transfers have dropped once or twice in the past to the drive from my
Win 7 laptop (netbook, actually), but I had put that down to lack of processing
power in the netbook. I'm sure you're right that there could be signs of disk
failure, so I must take the data off and run WD software to check it.

I'll continue to look at drivers too, but the problem is that as the drive never
gets mounted, I can't use its Preferences settings to update on the Win 8 PC.

Thanks again,
John



--
--------------------------------- --- -- -
Posted with NewsLeecher v6.5 Beta 2
Web @ http://www.newsleecher.com/?usenet
------------------- ----- ---- -- -

  #4  
Old January 25th 14, 04:04 PM posted to alt.comp.os.windows-8
Zaky Waky
external usenet poster
 
Posts: 24
Default Win 8 not offering to fix external USB drive file system

Brighty wrote in news:VEJEu.115356$ol1.45508
@fx03.iad:

Is Win 8 so fussy?


Not fussy, just broken.

Welcome to the wonderful world of Win8.
  #5  
Old January 25th 14, 10:48 PM posted to alt.comp.os.windows-8
Nil[_5_]
external usenet poster
 
Posts: 1,731
Default Win 8 not offering to fix external USB drive file system

On 25 Jan 2014, Zaky Waky wrote in
alt.comp.os.windows-8:

Brighty wrote in news:VEJEu.115356$ol1.45508
@fx03.iad:

Is Win 8 so fussy?


Not fussy, just broken.


How so?

Welcome to the wonderful world of Win8.

  #6  
Old January 25th 14, 10:59 PM posted to alt.comp.os.windows-8
Paul
external usenet poster
 
Posts: 18,275
Default Win 8 not offering to fix external USB drive file system

Brighty wrote:
In reply to "Paul" who wrote the following:

Brighty wrote:
I have a USB 2.0 WD My Passport Essential SE drive which I use with my Win 7
laptop. I always ignored a prompt on every USB plug in to repair the file
system
as it worked fine. But my new Win 8 PC refuses to see it in File Explorer,
it
appears and disappears constantly, playing the four tone chime over and
over. So
I repaired its file system on the Win 7 machine and now it starts without
complaint there, but still no luck in Win 8. The Win 8 PC offered to repair
it
once, and I accepted but it stopped a third of the way through, and Win 8
now no
longer offers to repair.

I have the latest 64 bit WD driver on the Win 8 PC, using different USB
slots
make no difference. I've tried a new USB cable which is good with other
peripherals. I have a lot of data on the drive, so a reformat is not on the
table. I have another external USB 2.0 drive which loads in Win 8 with no
difficulty.

Is Win 8 so fussy? Any help will be appreciated, I can raise it with WD, but
I'm
not sure that it's a drive problem.

Properties as shown in Win 8:
Device
USBSTOR\Disk&Ven_WD&Prod_My_Passport_071A&Rev_2019 \57584A314137304832383737&
0
was configured.

Driver Name: disk.inf
Class GUID: {4D36E967-E325-11CE-BFC1-08002BE10318}
Driver Date: 06/21/2006
Driver Version: 6.2.9200.16384
Driver Provider: Microsoft
Driver Section: disk_install.NT
Driver Rank: 0xFF0006
Matching Device ID: GenDisk
Outranked Drivers: disk.inf:GenDisk:00FF2002
Device Updated: false

Thanks
John

A few observations:

1) This could be a 2.5 inch drive, drawing all hard
drive power from the USB bus.
2) Excessive drive power consumption, will cause the
bus voltage to drop, the drive to spin down and spin up
again, you get "chimes" when the drive is detected again.
If that happens in the middle of CHKDSK, you're in trouble.
3) You need to ensure it isn't a power problem.

USB2 limits bus power to 500mA. Depending on the computer
type (laptop or desktop), the electrical circuit isn't nearly
as stingy as the specification suggests. Some of them, you
can draw 1000mA, before the self-resetting fuse opens up.

If you were to read the specs for the internal drive mechanism
itself, some of those draw 1000mA during spinup, then much
less current when in steady state. And that means, spec-wise,
we're in limbo. A few of the drives are at 500mA max, and
those are less likely to be an issue.

To see if this is a drive problem, you could remove it
from the casing. Some of these pre-packaged drives from
WD and Seagate, the packaging is designed to thwart easy
removal. If I need to "remove an enclosure" from the equation,
pulling the drive and connecting it to my desktop
SATA cabling, allows testing the drive directly.

*******

Another observation for you, is portable storage encourages
aggressive spin-down policies. That means the product has
internal settings, telling it to spin down after five seconds
of dis-use. This is hard on the drive, if done with aggression.
It is frequently used as a "cooling" solution, so the drive
can be sealed right up, and still remain cool.

The drive mechanism itself could be failing. And then it would
be hard to tell apart the various kinds of possible faults.

Now, if the computer had USB3 ports (powder blue plastic), you
were using Windows 8 USB3 drivers, I might believe it to be a
driver problem of some sort. If on the other hand, everything
in that path is USB2, a much older driver might be involved
(proven code and architecture), and Microsoft would be
"off the hook". I've heard a few complaints, when comparing
the third-party USB3 drivers, to the Microsoft driver for USB3,
so that's a possibility. But the root of the
problem just as easily, could be a non-reliable power problem,
or a drive mechanism about to fail. Perhaps if all the
OS observations were done on exactly the same computer
hardware, we could eliminate the bus power as an issue.
But if comparing two different computers, anything is
possible.

It's too bad these products, don't have an indicator light
to warn us of power problems. It's sure not a technology problem.
Just a lack of imagination.

Paul


Hello Pauk,

Thanks for the thoughtful reply. The Win 8 machine is a Sony Fit i7 with two USB
3.0 ports, I've tried both, and one is a charging port so I'll rule out a power
supply issue. The drive works faultlessly streaming video to a Merlin jukebox
style unit which also doesn't power it.

Heavy file transfers have dropped once or twice in the past to the drive from my
Win 7 laptop (netbook, actually), but I had put that down to lack of processing
power in the netbook. I'm sure you're right that there could be signs of disk
failure, so I must take the data off and run WD software to check it.

I'll continue to look at drivers too, but the problem is that as the drive never
gets mounted, I can't use its Preferences settings to update on the Win 8 PC.

Thanks again,
John


So your powering is the opposite of what I expected. Your Win8 has USB3
with good power (but problems). Your Win7 has USB2 and potential bad
power, but it works. So power probably isn't the problem. The machine
with what looks like good power, has the problems.

You mention a WD 64 bit driver. Why is that necessary ? And
what is in that driver ? Do you have a link to that driver ?

For USB Mass Storage, the software provided by the OS should be
sufficient. I'm curious what problem the WD software is proposing
to solve.

Sometimes, freaky drive behavior is caused by power management
interactions. Check Device Manager and make sure there are no
"Allow the computer to turn off this device to save power" boxes
that are ticked. Then try again. It's amazing how many points
in the computer, have power saving options, and those options
have the potential to make computer operation uneven. For a
laptop, some level of power saving is essential, such as down-clocking
the CPU and GPU when they're not being used. But other stuff is
just trivial. The difference between 4 hour battery life and
4.3 hour battery life, isn't worth some of the stingy settings
they use.

There have been enclosures, where the enclosure tells the drive
to spin down (to save power, reduce heat), and then the OS lacks
something to tell the drive to spin up again. Again, all part of power
management. And the user might be convinced it was an OS driver,
when it was just two bad designs bumping heads. With the enclosures,
you might not have any control over the spin-down behavior. Apparently,
it's in the drive firmware. And it's unclear whether you can issue the
appropriate IDE command, to make it stop.

Paul
  #7  
Old January 26th 14, 12:31 AM posted to alt.comp.os.windows-8
Gene E. Bloch[_5_]
external usenet poster
 
Posts: 1,720
Default Win 8 not offering to fix external USB drive file system

On 1/25/2014, Brighty posted:
Thanks for the thoughtful reply. The Win 8 machine is a Sony Fit i7
with two USB
3.0 ports, I've tried both, and one is a charging port so I'll rule
out a power
supply issue. The drive works faultlessly streaming video to a Merlin
jukebox
style unit which also doesn't power it.


I haven't checked this, but I have a suspicion that the extra power on
a USB3 port is only available to USB3 drives connected with a USB3
cable...

You might try to track down a Y-cable for USB2, with a pigtail to
connect to a second USB2 output port for extra power to an external
drive.

--
Gene E. Bloch (Stumbling Bloch)
  #8  
Old January 26th 14, 01:37 AM posted to alt.comp.os.windows-8
Paul
external usenet poster
 
Posts: 18,275
Default Win 8 not offering to fix external USB drive file system

Gene E. Bloch wrote:
On 1/25/2014, Brighty posted:
Thanks for the thoughtful reply. The Win 8 machine is a Sony Fit i7
with two USB
3.0 ports, I've tried both, and one is a charging port so I'll rule
out a power
supply issue. The drive works faultlessly streaming video to a Merlin
jukebox
style unit which also doesn't power it.


I haven't checked this, but I have a suspicion that the extra power on a
USB3 port is only available to USB3 drives connected with a USB3 cable...

You might try to track down a Y-cable for USB2, with a pigtail to
connect to a second USB2 output port for extra power to an external drive.


There is a pinout here for your consideration. Only one VBUS
pin is evident. The five new USB3 signals, are a TX diff
pair, an RX diff pair, and a ground between them for crosstalk.

http://pinoutsguide.com/Slots/usb_3_...r_pinout.shtml

I can't honestly say why the USB3 current limit is higher
than the USB2 one.

Paul
  #9  
Old January 26th 14, 02:28 AM posted to alt.comp.os.windows-8
Gene E. Bloch[_5_]
external usenet poster
 
Posts: 1,720
Default Win 8 not offering to fix external USB drive file system

On 1/25/2014, Paul posted:
Gene E. Bloch wrote:
On 1/25/2014, Brighty posted:
Thanks for the thoughtful reply. The Win 8 machine is a Sony Fit
i7 with two USB
3.0 ports, I've tried both, and one is a charging port so I'll
rule out a power
supply issue. The drive works faultlessly streaming video to a
Merlin jukebox
style unit which also doesn't power it.


I haven't checked this, but I have a suspicion that the extra power
on a USB3 port is only available to USB3 drives connected with a
USB3 cable...

You might try to track down a Y-cable for USB2, with a pigtail to
connect to a second USB2 output port for extra power to an external
drive.


There is a pinout here for your consideration. Only one VBUS
pin is evident. The five new USB3 signals, are a TX diff
pair, an RX diff pair, and a ground between them for crosstalk.


http://pinoutsguide.com/Slots/usb_3_...r_pinout.shtml


I can't honestly say why the USB3 current limit is higher
than the USB2 one.


Paul


Thanks. I shouldn't have been so lazy :-)

As for the larger current limit, that would just be built into the port
circuitry.

The only question, and I think it's silly even though it's my own
question, is whether the USB3 port would sense the absence of the extra
USB3 pins and thereby reduce the current limit for a USB2 device.

I didn't find an answer to that in my brief search, but in the process
I did mange to notice that USB3 is full duplex to USB2's half duplex.
That's cool.

--
Gene E. Bloch (Stumbling Bloch)
  #10  
Old January 26th 14, 06:04 PM posted to alt.comp.os.windows-8
Brighty
external usenet poster
 
Posts: 4
Default Win 8 not offering to fix external USB drive file system

In reply to "Paul" who wrote the following:

Brighty wrote:
In reply to "Paul" who wrote the following:

Brighty wrote:
I have a USB 2.0 WD My Passport Essential SE drive which I use with my
Win 7
laptop. I always ignored a prompt on every USB plug in to repair the
file
system
as it worked fine. But my new Win 8 PC refuses to see it in File
Explorer,
it
appears and disappears constantly, playing the four tone chime over and
over. So
I repaired its file system on the Win 7 machine and now it starts
without
complaint there, but still no luck in Win 8. The Win 8 PC offered to
repair
it
once, and I accepted but it stopped a third of the way through, and Win
8
now no
longer offers to repair.

I have the latest 64 bit WD driver on the Win 8 PC, using different USB
slots
make no difference. I've tried a new USB cable which is good with other
peripherals. I have a lot of data on the drive, so a reformat is not on
the
table. I have another external USB 2.0 drive which loads in Win 8 with
no
difficulty.

Is Win 8 so fussy? Any help will be appreciated, I can raise it with WD,
but
I'm
not sure that it's a drive problem.

Properties as shown in Win 8:
Device
USBSTOR\Disk&Ven_WD&Prod_My_Passport_071A&Rev_2019 \57584A314137304832383
737&
0
was configured.

Driver Name: disk.inf
Class GUID: {4D36E967-E325-11CE-BFC1-08002BE10318}
Driver Date: 06/21/2006
Driver Version: 6.2.9200.16384
Driver Provider: Microsoft
Driver Section: disk_install.NT
Driver Rank: 0xFF0006
Matching Device ID: GenDisk
Outranked Drivers: disk.inf:GenDisk:00FF2002
Device Updated: false

Thanks
John
A few observations:

1) This could be a 2.5 inch drive, drawing all hard
drive power from the USB bus.
2) Excessive drive power consumption, will cause the
bus voltage to drop, the drive to spin down and spin up
again, you get "chimes" when the drive is detected again.
If that happens in the middle of CHKDSK, you're in trouble.
3) You need to ensure it isn't a power problem.

USB2 limits bus power to 500mA. Depending on the computer
type (laptop or desktop), the electrical circuit isn't nearly
as stingy as the specification suggests. Some of them, you
can draw 1000mA, before the self-resetting fuse opens up.

If you were to read the specs for the internal drive mechanism
itself, some of those draw 1000mA during spinup, then much
less current when in steady state. And that means, spec-wise,
we're in limbo. A few of the drives are at 500mA max, and
those are less likely to be an issue.

To see if this is a drive problem, you could remove it
from the casing. Some of these pre-packaged drives from
WD and Seagate, the packaging is designed to thwart easy
removal. If I need to "remove an enclosure" from the equation,
pulling the drive and connecting it to my desktop
SATA cabling, allows testing the drive directly.

*******

Another observation for you, is portable storage encourages
aggressive spin-down policies. That means the product has
internal settings, telling it to spin down after five seconds
of dis-use. This is hard on the drive, if done with aggression.
It is frequently used as a "cooling" solution, so the drive
can be sealed right up, and still remain cool.

The drive mechanism itself could be failing. And then it would
be hard to tell apart the various kinds of possible faults.

Now, if the computer had USB3 ports (powder blue plastic), you
were using Windows 8 USB3 drivers, I might believe it to be a
driver problem of some sort. If on the other hand, everything
in that path is USB2, a much older driver might be involved
(proven code and architecture), and Microsoft would be
"off the hook". I've heard a few complaints, when comparing
the third-party USB3 drivers, to the Microsoft driver for USB3,
so that's a possibility. But the root of the
problem just as easily, could be a non-reliable power problem,
or a drive mechanism about to fail. Perhaps if all the
OS observations were done on exactly the same computer
hardware, we could eliminate the bus power as an issue.
But if comparing two different computers, anything is
possible.

It's too bad these products, don't have an indicator light
to warn us of power problems. It's sure not a technology problem.
Just a lack of imagination.

Paul


Hello Pauk,

Thanks for the thoughtful reply. The Win 8 machine is a Sony Fit i7 with two
USB
3.0 ports, I've tried both, and one is a charging port so I'll rule out a
power
supply issue. The drive works faultlessly streaming video to a Merlin
jukebox
style unit which also doesn't power it.

Heavy file transfers have dropped once or twice in the past to the drive
from my
Win 7 laptop (netbook, actually), but I had put that down to lack of
processing
power in the netbook. I'm sure you're right that there could be signs of
disk
failure, so I must take the data off and run WD software to check it.

I'll continue to look at drivers too, but the problem is that as the drive
never
gets mounted, I can't use its Preferences settings to update on the Win 8
PC.

Thanks again,
John


So your powering is the opposite of what I expected. Your Win8 has USB3
with good power (but problems). Your Win7 has USB2 and potential bad
power, but it works. So power probably isn't the problem. The machine
with what looks like good power, has the problems.

You mention a WD 64 bit driver. Why is that necessary ? And
what is in that driver ? Do you have a link to that driver ?

For USB Mass Storage, the software provided by the OS should be
sufficient. I'm curious what problem the WD software is proposing
to solve.

Sometimes, freaky drive behavior is caused by power management
interactions. Check Device Manager and make sure there are no
"Allow the computer to turn off this device to save power" boxes
that are ticked. Then try again. It's amazing how many points
in the computer, have power saving options, and those options
have the potential to make computer operation uneven. For a
laptop, some level of power saving is essential, such as down-clocking
the CPU and GPU when they're not being used. But other stuff is
just trivial. The difference between 4 hour battery life and
4.3 hour battery life, isn't worth some of the stingy settings
they use.

There have been enclosures, where the enclosure tells the drive
to spin down (to save power, reduce heat), and then the OS lacks
something to tell the drive to spin up again. Again, all part of power
management. And the user might be convinced it was an OS driver,
when it was just two bad designs bumping heads. With the enclosures,
you might not have any control over the spin-down behavior. Apparently,
it's in the drive firmware. And it's unclear whether you can issue the
appropriate IDE command, to make it stop.

Paul


Hi,

I installed the driver WD_SES_Driver_Setup_x64 from
http://wdc.custhelp.com/app/answers/detail/a_id/5419 because I suspected some
native Win 8 naughtiness as the drive worked well elsewhere. I can't check power
saving options for the drive because it never gets so far as to load in Device
Manager.

As these days my curiosity power seems inverse to my free time, I guess I'll end
up ditching the drive and buying a new USB 3.0 replacement.

Thanks again.

John


--
--------------------------------- --- -- -
Posted with NewsLeecher v6.5 Beta 2
Web @ http://www.newsleecher.com/?usenet
------------------- ----- ---- -- -

  #11  
Old January 26th 14, 06:08 PM posted to alt.comp.os.windows-8
Brighty
external usenet poster
 
Posts: 4
Default Win 8 not offering to fix external USB drive file system

In reply to "Gene E. Bloch" who wrote the following:

On 1/25/2014, Brighty posted:
Thanks for the thoughtful reply. The Win 8 machine is a Sony Fit i7
with two USB
3.0 ports, I've tried both, and one is a charging port so I'll rule
out a power
supply issue. The drive works faultlessly streaming video to a Merlin
jukebox
style unit which also doesn't power it.


I haven't checked this, but I have a suspicion that the extra power on
a USB3 port is only available to USB3 drives connected with a USB3
cable...

You might try to track down a Y-cable for USB2, with a pigtail to
connect to a second USB2 output port for extra power to an external
drive.

--
Gene E. Bloch (Stumbling Bloch)


Thanks for the thought. It would be a shame if the port doesn't charge other
devices (phones, etc) but the Sony power brick sports a USB charging port, so I
guess it would be churlish to complain.


--
--------------------------------- --- -- -
Posted with NewsLeecher v6.5 Beta 2
Web @ http://www.newsleecher.com/?usenet
------------------- ----- ---- -- -

  #12  
Old January 26th 14, 08:25 PM posted to alt.comp.os.windows-8
Paul
external usenet poster
 
Posts: 18,275
Default Win 8 not offering to fix external USB drive file system

Brighty wrote:
In reply to "Paul" who wrote the following:

Brighty wrote:
In reply to "Paul" who wrote the following:

Brighty wrote:
I have a USB 2.0 WD My Passport Essential SE drive which I use with my
Win 7
laptop. I always ignored a prompt on every USB plug in to repair the
file
system
as it worked fine. But my new Win 8 PC refuses to see it in File
Explorer,
it
appears and disappears constantly, playing the four tone chime over and
over. So
I repaired its file system on the Win 7 machine and now it starts
without
complaint there, but still no luck in Win 8. The Win 8 PC offered to
repair
it
once, and I accepted but it stopped a third of the way through, and Win
8
now no
longer offers to repair.

I have the latest 64 bit WD driver on the Win 8 PC, using different USB
slots
make no difference. I've tried a new USB cable which is good with other
peripherals. I have a lot of data on the drive, so a reformat is not on
the
table. I have another external USB 2.0 drive which loads in Win 8 with
no
difficulty.

Is Win 8 so fussy? Any help will be appreciated, I can raise it with WD,
but
I'm
not sure that it's a drive problem.

Properties as shown in Win 8:
Device
USBSTOR\Disk&Ven_WD&Prod_My_Passport_071A&Rev_2019 \57584A314137304832383
737&
0
was configured.

Driver Name: disk.inf
Class GUID: {4D36E967-E325-11CE-BFC1-08002BE10318}
Driver Date: 06/21/2006
Driver Version: 6.2.9200.16384
Driver Provider: Microsoft
Driver Section: disk_install.NT
Driver Rank: 0xFF0006
Matching Device ID: GenDisk
Outranked Drivers: disk.inf:GenDisk:00FF2002
Device Updated: false

Thanks
John
A few observations:

1) This could be a 2.5 inch drive, drawing all hard
drive power from the USB bus.
2) Excessive drive power consumption, will cause the
bus voltage to drop, the drive to spin down and spin up
again, you get "chimes" when the drive is detected again.
If that happens in the middle of CHKDSK, you're in trouble.
3) You need to ensure it isn't a power problem.

USB2 limits bus power to 500mA. Depending on the computer
type (laptop or desktop), the electrical circuit isn't nearly
as stingy as the specification suggests. Some of them, you
can draw 1000mA, before the self-resetting fuse opens up.

If you were to read the specs for the internal drive mechanism
itself, some of those draw 1000mA during spinup, then much
less current when in steady state. And that means, spec-wise,
we're in limbo. A few of the drives are at 500mA max, and
those are less likely to be an issue.

To see if this is a drive problem, you could remove it
from the casing. Some of these pre-packaged drives from
WD and Seagate, the packaging is designed to thwart easy
removal. If I need to "remove an enclosure" from the equation,
pulling the drive and connecting it to my desktop
SATA cabling, allows testing the drive directly.

*******

Another observation for you, is portable storage encourages
aggressive spin-down policies. That means the product has
internal settings, telling it to spin down after five seconds
of dis-use. This is hard on the drive, if done with aggression.
It is frequently used as a "cooling" solution, so the drive
can be sealed right up, and still remain cool.

The drive mechanism itself could be failing. And then it would
be hard to tell apart the various kinds of possible faults.

Now, if the computer had USB3 ports (powder blue plastic), you
were using Windows 8 USB3 drivers, I might believe it to be a
driver problem of some sort. If on the other hand, everything
in that path is USB2, a much older driver might be involved
(proven code and architecture), and Microsoft would be
"off the hook". I've heard a few complaints, when comparing
the third-party USB3 drivers, to the Microsoft driver for USB3,
so that's a possibility. But the root of the
problem just as easily, could be a non-reliable power problem,
or a drive mechanism about to fail. Perhaps if all the
OS observations were done on exactly the same computer
hardware, we could eliminate the bus power as an issue.
But if comparing two different computers, anything is
possible.

It's too bad these products, don't have an indicator light
to warn us of power problems. It's sure not a technology problem.
Just a lack of imagination.

Paul
Hello Pauk,

Thanks for the thoughtful reply. The Win 8 machine is a Sony Fit i7 with two
USB
3.0 ports, I've tried both, and one is a charging port so I'll rule out a
power
supply issue. The drive works faultlessly streaming video to a Merlin
jukebox
style unit which also doesn't power it.

Heavy file transfers have dropped once or twice in the past to the drive
from my
Win 7 laptop (netbook, actually), but I had put that down to lack of
processing
power in the netbook. I'm sure you're right that there could be signs of
disk
failure, so I must take the data off and run WD software to check it.

I'll continue to look at drivers too, but the problem is that as the drive
never
gets mounted, I can't use its Preferences settings to update on the Win 8
PC.

Thanks again,
John

So your powering is the opposite of what I expected. Your Win8 has USB3
with good power (but problems). Your Win7 has USB2 and potential bad
power, but it works. So power probably isn't the problem. The machine
with what looks like good power, has the problems.

You mention a WD 64 bit driver. Why is that necessary ? And
what is in that driver ? Do you have a link to that driver ?

For USB Mass Storage, the software provided by the OS should be
sufficient. I'm curious what problem the WD software is proposing
to solve.

Sometimes, freaky drive behavior is caused by power management
interactions. Check Device Manager and make sure there are no
"Allow the computer to turn off this device to save power" boxes
that are ticked. Then try again. It's amazing how many points
in the computer, have power saving options, and those options
have the potential to make computer operation uneven. For a
laptop, some level of power saving is essential, such as down-clocking
the CPU and GPU when they're not being used. But other stuff is
just trivial. The difference between 4 hour battery life and
4.3 hour battery life, isn't worth some of the stingy settings
they use.

There have been enclosures, where the enclosure tells the drive
to spin down (to save power, reduce heat), and then the OS lacks
something to tell the drive to spin up again. Again, all part of power
management. And the user might be convinced it was an OS driver,
when it was just two bad designs bumping heads. With the enclosures,
you might not have any control over the spin-down behavior. Apparently,
it's in the drive firmware. And it's unclear whether you can issue the
appropriate IDE command, to make it stop.

Paul


Hi,

I installed the driver WD_SES_Driver_Setup_x64 from
http://wdc.custhelp.com/app/answers/detail/a_id/5419 because I suspected some
native Win 8 naughtiness as the drive worked well elsewhere. I can't check power
saving options for the drive because it never gets so far as to load in Device
Manager.

As these days my curiosity power seems inverse to my free time, I guess I'll end
up ditching the drive and buying a new USB 3.0 replacement.

Thanks again.

John



"WD SES driver download and instructions for recovering the WD SmartWare installer"

OK, so I downloaded the (small) driver file, and looked inside the .msi with 7ZIP.

Hmmm. I wonder why that driver would ever be needed ?

; wdcsam.inf - WDC SCSI Architecture Model (SAM) WDM driver
; Copyright (C) 2006-2009 Western Digital Technologies

WDC_Provider = "Western Digital Technologies"
WDC_Mfg = "Western Digital Technologies"
WDC_SAM_SourceDiskDesc = "WD External Storage Driver Disk"

WDC_SAM_ClassName = "WD Drive Management devices"
WDC_SAM_ServiceName = "WD SCSI Pass Thru driver"
WDC_SAM_ServiceDesc = "Manages WD external storage products."

WDC_SES_DevDesc = "WD SES Device"

[WDC_SAM_CopyFiles]
wdcsam.sys

[WDC_SAM_CopyFiles_x64]
wdcsam64.sys

Does that access the drive, in other than a USB Mass Storage
regular way ? Or is that a filter driver that sits on top
of a regular USB connection ? It almost looks like the former
to me.

*******

If I go back to the lead-in article...

http://wdc.custhelp.com/app/answers/detail/a_id/3739

"The SES driver is not required for your drive to be recognized by your computer.

If you wish to use the drive as a simple hard drive and do not require
access to the advanced features of the drive, you can hide the Virtual CD"

So that sounds a bit like a U3 product, for hosting portable
software. And that means, the drive isn't *exactly* like
everybody else's USB hard drive. So if I'm playing with
my USB hard drive here, it doesn't have a virtual CD inside
it. Your drive will present additional configuration information,
and the USB config space will be more complicated than
a regular controller would present.

Stuff like that (U3 or virtual CD), really ****es me off,
due to the difficulty of removing it later. I'm very careful
to buy hardware that is as "vanilla" as possible. I hate
surprises!

I would go to Programs and Features, and see if that
driver can be removed. Once that's done, the drive
may behave more like a regular USB drive. I don't know if
you'd see the virtual CD appear or not. Or what you might
see in (File) Explorer.

It probably has nothing to do with your problems, and the
problems are still at the USB bus level. But it's a complication
you don't need right now.

Paul
 




Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off






All times are GMT +1. The time now is 05:29 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 PCbanter.
The comments are property of their posters.