If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Networking two computers
I have tried dozens of times to get my two computers to
network, but I have had no luck. I have run the Windows XP netork wizard (if you want to call it that), but EVERYTIME I run it, it fails to set up the wizard. I keep getting the following message when I try to View the workgroup computers-- Mshome is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permission. The list of servers for this workgroup is not currently available. Any clues as to what I can do to get this network to work? Obviously Windows XP does not work well for networking! |
Ads |
#2
|
|||
|
|||
Networking two computers
XP works very well for networks..
What is your network setup? direct connect? (you need a cross-over cable) hub? router? NICs? "Bob" wrote in message ... I have tried dozens of times to get my two computers to network, but I have had no luck. I have run the Windows XP netork wizard (if you want to call it that), but EVERYTIME I run it, it fails to set up the wizard. I keep getting the following message when I try to View the workgroup computers-- Mshome is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permission. The list of servers for this workgroup is not currently available. Any clues as to what I can do to get this network to work? Obviously Windows XP does not work well for networking! |
#3
|
|||
|
|||
Networking two computers
Joe,
what do you mean by your question? I'm not sure what you mean, but I'll try to answer it. I am using a router and I have a desktop and laptop. The network wizard in XP is doing absolutely nothing to help me. I keep getting error messages when I try to run the wizard, the computers can't find each other, it cannot find MSHOME. I have tried to run the wizard at least a couple dozen times over the past year and a half, and it NEVER works. You think I'm frustrated? I passed frustrated about 6 months ago. Thanks, Bob -----Original Message----- How are you connecting the PC's Bob? with what type of hardware? and please calm down I know you are frustrated but hang in there you will get it. Joe -----Original Message----- Eric, thanks for your reply, but I tried your suggestions and of course they didn't work. As far as I'm concerned, Microsoft can take their network wizard and shove it up Bill Gates' ass. Bob -----Original Message----- Greetings Bob, Make sure the XP's firewall is disabled. It will block file and printer sharing by default. If you installed a third party firewall such as ZoneAlarm, Sygate, or Norton make sure it is properly configured for the network. Ensure NetBIOS over TCP/IP is enabled. Details here. Enable NetBIOS Over TCP/IP (NetBT) http://www.practicallynetworked.com/sharing/troubleshoo t/ netbt.htm __________________ Eric "Bob" wrote in message . .. I have tried dozens of times to get my two computers to network, but I have had no luck. I have run the Windows XP netork wizard (if you want to call it that), but EVERYTIME I run it, it fails to set up the wizard. I keep getting the following message when I try to View the workgroup computers-- Mshome is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permission. The list of servers for this workgroup is not currently available. Any clues as to what I can do to get this network to work? Obviously Windows XP does not work well for networking! . . . |
#4
|
|||
|
|||
Networking two computers
Sorry David, but dozens of attempts at setting up a
network through XP has told me that it does not work good for setting up a network. Bob -----Original Message----- XP works very well for networks.. What is your network setup? direct connect? (you need a cross-over cable) hub? router? NICs? "Bob" wrote in message ... I have tried dozens of times to get my two computers to network, but I have had no luck. I have run the Windows XP netork wizard (if you want to call it that), but EVERYTIME I run it, it fails to set up the wizard. I keep getting the following message when I try to View the workgroup computers-- Mshome is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permission. The list of servers for this workgroup is not currently available. Any clues as to what I can do to get this network to work? Obviously Windows XP does not work well for networking! . |
#5
|
|||
|
|||
Networking two computers
Glad to see your back. So you have never been able to
connect to the internet? Ok is there a main PC or does your internet connection come from the wall per se" into the router? I suggest that you have your internet connection from your ISP (from the wall) go directly into your PC and then add another NIC card going out to your router or just install a wireless nic and one inside your laptop. Another configuration is this. If all you have are two PC's 1 desktop and 1 laptop It should work with the router Like this: Into the router from your cable modem/ISP/Wall make sure you are using the correct port on the router (there is only one for incoming) and then the following cables or wireles out of the router (outgoing) Think about trying to connect without using the wizard an see what you get. Just another test here Bob: plug the internet connection from the wall into the router and then plug a cable out of the router into the laptop or PC just one of them and see if you can get to the net. I do not know exactly how you want to network so I am assuming you want all your PC's to access the net via the router. Joe -----Original Message----- Joe, what do you mean by your question? I'm not sure what you mean, but I'll try to answer it. I am using a router and I have a desktop and laptop. The network wizard in XP is doing absolutely nothing to help me. I keep getting error messages when I try to run the wizard, the computers can't find each other, it cannot find MSHOME. I have tried to run the wizard at least a couple dozen times over the past year and a half, and it NEVER works. You think I'm frustrated? I passed frustrated about 6 months ago. Thanks, Bob -----Original Message----- How are you connecting the PC's Bob? with what type of hardware? and please calm down I know you are frustrated but hang in there you will get it. Joe -----Original Message----- Eric, thanks for your reply, but I tried your suggestions and of course they didn't work. As far as I'm concerned, Microsoft can take their network wizard and shove it up Bill Gates' ass. Bob -----Original Message----- Greetings Bob, Make sure the XP's firewall is disabled. It will block file and printer sharing by default. If you installed a third party firewall such as ZoneAlarm, Sygate, or Norton make sure it is properly configured for the network. Ensure NetBIOS over TCP/IP is enabled. Details here. Enable NetBIOS Over TCP/IP (NetBT) http://www.practicallynetworked.com/sharing/troubleshoo t/ netbt.htm __________________ Eric "Bob" wrote in message .. . I have tried dozens of times to get my two computers to network, but I have had no luck. I have run the Windows XP netork wizard (if you want to call it that), but EVERYTIME I run it, it fails to set up the wizard. I keep getting the following message when I try to View the workgroup computers-- Mshome is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permission. The list of servers for this workgroup is not currently available. Any clues as to what I can do to get this network to work? Obviously Windows XP does not work well for networking! . . . . |
#6
|
|||
|
|||
Networking two computers
Greetings Bob,
Make sure the XP's firewall is disabled. It will block file and printer sharing by default. If you installed a third party firewall such as ZoneAlarm, Sygate, or Norton make sure it is properly configured for the network. Ensure NetBIOS over TCP/IP is enabled. Details here. Enable NetBIOS Over TCP/IP (NetBT) http://www.practicallynetworked.com/...hoot/netbt.htm __________________ Eric "Bob" wrote in message ... I have tried dozens of times to get my two computers to network, but I have had no luck. I have run the Windows XP netork wizard (if you want to call it that), but EVERYTIME I run it, it fails to set up the wizard. I keep getting the following message when I try to View the workgroup computers-- Mshome is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permission. The list of servers for this workgroup is not currently available. Any clues as to what I can do to get this network to work? Obviously Windows XP does not work well for networking! |
#7
|
|||
|
|||
Networking two computers
Joe,
Maybe I should give you more information about my situation. I have been connected to the internet for years. Each computer can connect on their own. I have a cable modem. The router is connected to the modem and then each computer is connected to the router. I have a desktop and a laptop. Each computer connects separately, but I cannot share files between the two computers. I have tried the "wizard" as Microsoft calls it, and I have tried it using every single configuration they offer. No matter what I try, it doesn't work. The computers can't find each other, and then I keep getting error messages telling me to run the wizard again. Hopefully I have provided enough information to give you more insight. Please refer to my original post to see the error message I keep getting. Thanks, Bob -----Original Message----- Glad to see your back. So you have never been able to connect to the internet? Ok is there a main PC or does your internet connection come from the wall per se" into the router? I suggest that you have your internet connection from your ISP (from the wall) go directly into your PC and then add another NIC card going out to your router or just install a wireless nic and one inside your laptop. Another configuration is this. If all you have are two PC's 1 desktop and 1 laptop It should work with the router Like this: Into the router from your cable modem/ISP/Wall make sure you are using the correct port on the router (there is only one for incoming) and then the following cables or wireles out of the router (outgoing) Think about trying to connect without using the wizard an see what you get. Just another test here Bob: plug the internet connection from the wall into the router and then plug a cable out of the router into the laptop or PC just one of them and see if you can get to the net. I do not know exactly how you want to network so I am assuming you want all your PC's to access the net via the router. Joe -----Original Message----- Joe, what do you mean by your question? I'm not sure what you mean, but I'll try to answer it. I am using a router and I have a desktop and laptop. The network wizard in XP is doing absolutely nothing to help me. I keep getting error messages when I try to run the wizard, the computers can't find each other, it cannot find MSHOME. I have tried to run the wizard at least a couple dozen times over the past year and a half, and it NEVER works. You think I'm frustrated? I passed frustrated about 6 months ago. Thanks, Bob -----Original Message----- How are you connecting the PC's Bob? with what type of hardware? and please calm down I know you are frustrated but hang in there you will get it. Joe -----Original Message----- Eric, thanks for your reply, but I tried your suggestions and of course they didn't work. As far as I'm concerned, Microsoft can take their network wizard and shove it up Bill Gates' ass. Bob -----Original Message----- Greetings Bob, Make sure the XP's firewall is disabled. It will block file and printer sharing by default. If you installed a third party firewall such as ZoneAlarm, Sygate, or Norton make sure it is properly configured for the network. Ensure NetBIOS over TCP/IP is enabled. Details here. Enable NetBIOS Over TCP/IP (NetBT) http://www.practicallynetworked.com/sharing/troublesh oo t/ netbt.htm __________________ Eric "Bob" wrote in message . .. I have tried dozens of times to get my two computers to network, but I have had no luck. I have run the Windows XP netork wizard (if you want to call it that), but EVERYTIME I run it, it fails to set up the wizard. I keep getting the following message when I try to View the workgroup computers-- Mshome is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permission. The list of servers for this workgroup is not currently available. Any clues as to what I can do to get this network to work? Obviously Windows XP does not work well for networking! . . . . . |
#8
|
|||
|
|||
Networking two computers
What are the IPs of each of the computers?
Are you able to manually enter a shortcut to the other computer in the form: \\Desktop\Shared or \\Laptop\Shared Where Shared is the name of a folder on that computer that is set to be shared on the network. If you want to get the two computers to be networked safely, you need to have them both with the same first 3 sections of the IP address, i.e. 192.168.1.xx and the router should have a connection to the cable modem. I have set up several networks with XP on networks with anywhere from 2 to 15 computers using either a single router or a switch or 3 routers daisy chained together. Once I got the routers set up to properly, I just ran the network setup wizard for each computer and I was up and running. Try starting from scratch. Unplug everything. EVERYTHING. Connect the power to the router and then press and hold the reset button for 30 seconds (there should be one on the back or the bottom). Find the instructions that came with the router (or find them of the router manufacturer's website) and follow them step by step. While you're setting everything up, only have ONE computer connected, once the router is configured properly, connect the other computer. Make sure that you have the router set to act as a DHCP server. Check the IP addresses of each computer. Check this both from "ipconfig /all" in the command prompt and in the router's DHCP configuration menu. The computers should have the exact same subnet mask and the first 3 parts of the IP addresses the same, i.e 192.168.1.xx. If this doesn't fit, then you're never going to get the Windows Network Setup Wizard to work. Once you've got the IPs and subnet masks described above, NOW run the setup wizard. Make sure that you input the exact same settings into each computer. Share a folder and see if you can make a shortcut to that folder in the form \\computer\folder If this still doesn't work (and you've actually followed everything that I've said here), let us know. Hope this helps, Nick nkjg/at\interchange/dot\ubc/dot\ca "The definition of insanity: doing the same thing over and over expecting different results." -----Original Message----- Joe, Maybe I should give you more information about my situation. I have been connected to the internet for years. Each computer can connect on their own. I have a cable modem. The router is connected to the modem and then each computer is connected to the router. I have a desktop and a laptop. Each computer connects separately, but I cannot share files between the two computers. I have tried the "wizard" as Microsoft calls it, and I have tried it using every single configuration they offer. No matter what I try, it doesn't work. The computers can't find each other, and then I keep getting error messages telling me to run the wizard again. Hopefully I have provided enough information to give you more insight. Please refer to my original post to see the error message I keep getting. Thanks, Bob -----Original Message----- Glad to see your back. So you have never been able to connect to the internet? Ok is there a main PC or does your internet connection come from the wall per se" into the router? I suggest that you have your internet connection from your ISP (from the wall) go directly into your PC and then add another NIC card going out to your router or just install a wireless nic and one inside your laptop. Another configuration is this. If all you have are two PC's 1 desktop and 1 laptop It should work with the router Like this: Into the router from your cable modem/ISP/Wall make sure you are using the correct port on the router (there is only one for incoming) and then the following cables or wireles out of the router (outgoing) Think about trying to connect without using the wizard an see what you get. Just another test here Bob: plug the internet connection from the wall into the router and then plug a cable out of the router into the laptop or PC just one of them and see if you can get to the net. I do not know exactly how you want to network so I am assuming you want all your PC's to access the net via the router. Joe -----Original Message----- Joe, what do you mean by your question? I'm not sure what you mean, but I'll try to answer it. I am using a router and I have a desktop and laptop. The network wizard in XP is doing absolutely nothing to help me. I keep getting error messages when I try to run the wizard, the computers can't find each other, it cannot find MSHOME. I have tried to run the wizard at least a couple dozen times over the past year and a half, and it NEVER works. You think I'm frustrated? I passed frustrated about 6 months ago. Thanks, Bob -----Original Message----- How are you connecting the PC's Bob? with what type of hardware? and please calm down I know you are frustrated but hang in there you will get it. Joe -----Original Message----- Eric, thanks for your reply, but I tried your suggestions and of course they didn't work. As far as I'm concerned, Microsoft can take their network wizard and shove it up Bill Gates' ass. Bob -----Original Message----- Greetings Bob, Make sure the XP's firewall is disabled. It will block file and printer sharing by default. If you installed a third party firewall such as ZoneAlarm, Sygate, or Norton make sure it is properly configured for the network. Ensure NetBIOS over TCP/IP is enabled. Details here. Enable NetBIOS Over TCP/IP (NetBT) http://www.practicallynetworked.com/sharing/troubles h oo t/ netbt.htm __________________ Eric "Bob" wrote in message ... I have tried dozens of times to get my two computers to network, but I have had no luck. I have run the Windows XP netork wizard (if you want to call it that), but EVERYTIME I run it, it fails to set up the wizard. I keep getting the following message when I try to View the workgroup computers-- Mshome is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permission. The list of servers for this workgroup is not currently available. Any clues as to what I can do to get this network to work? Obviously Windows XP does not work well for networking! . . . . . . |
#9
|
|||
|
|||
Networking two computers
What are the IPs of each of the computers?
Are you able to manually enter a shortcut to the other computer in the form: \\Desktop\Shared or \\Laptop\Shared Where Shared is the name of a folder on that computer that is set to be shared on the network. If you want to get the two computers to be networked safely, you need to have them both with the same first 3 sections of the IP address, i.e. 192.168.1.xx and the router should have a connection to the cable modem. I have set up several networks with XP on networks with anywhere from 2 to 15 computers using either a single router or a switch or 3 routers daisy chained together. Once I got the routers set up to properly, I just ran the network setup wizard for each computer and I was up and running. Try starting from scratch. Unplug everything. EVERYTHING. Connect the power to the router and then press and hold the reset button for 30 seconds (there should be one on the back or the bottom). Find the instructions that came with the router (or find them of the router manufacturer's website) and follow them step by step. While you're setting everything up, only have ONE computer connected, once the router is configured properly, connect the other computer. Make sure that you have the router set to act as a DHCP server. Check the IP addresses of each computer. Check this both from "ipconfig /all" in the command prompt and in the router's DHCP configuration menu. The computers should have the exact same subnet mask and the first 3 parts of the IP addresses the same, i.e 192.168.1.xx. If this doesn't fit, then you're never going to get the Windows Network Setup Wizard to work. Once you've got the IPs and subnet masks described above, NOW run the setup wizard. Make sure that you input the exact same settings into each computer. Share a folder and see if you can make a shortcut to that folder in the form \\computer\folder If this still doesn't work (and you've actually followed everything that I've said here), let us know. Hope this helps, Nick nkjg/at\interchange/dot\ubc/dot\ca "The definition of insanity: doing the same thing over and over expecting different results." -----Original Message----- Joe, Maybe I should give you more information about my situation. I have been connected to the internet for years. Each computer can connect on their own. I have a cable modem. The router is connected to the modem and then each computer is connected to the router. I have a desktop and a laptop. Each computer connects separately, but I cannot share files between the two computers. I have tried the "wizard" as Microsoft calls it, and I have tried it using every single configuration they offer. No matter what I try, it doesn't work. The computers can't find each other, and then I keep getting error messages telling me to run the wizard again. Hopefully I have provided enough information to give you more insight. Please refer to my original post to see the error message I keep getting. Thanks, Bob -----Original Message----- Glad to see your back. So you have never been able to connect to the internet? Ok is there a main PC or does your internet connection come from the wall per se" into the router? I suggest that you have your internet connection from your ISP (from the wall) go directly into your PC and then add another NIC card going out to your router or just install a wireless nic and one inside your laptop. Another configuration is this. If all you have are two PC's 1 desktop and 1 laptop It should work with the router Like this: Into the router from your cable modem/ISP/Wall make sure you are using the correct port on the router (there is only one for incoming) and then the following cables or wireles out of the router (outgoing) Think about trying to connect without using the wizard an see what you get. Just another test here Bob: plug the internet connection from the wall into the router and then plug a cable out of the router into the laptop or PC just one of them and see if you can get to the net. I do not know exactly how you want to network so I am assuming you want all your PC's to access the net via the router. Joe -----Original Message----- Joe, what do you mean by your question? I'm not sure what you mean, but I'll try to answer it. I am using a router and I have a desktop and laptop. The network wizard in XP is doing absolutely nothing to help me. I keep getting error messages when I try to run the wizard, the computers can't find each other, it cannot find MSHOME. I have tried to run the wizard at least a couple dozen times over the past year and a half, and it NEVER works. You think I'm frustrated? I passed frustrated about 6 months ago. Thanks, Bob -----Original Message----- How are you connecting the PC's Bob? with what type of hardware? and please calm down I know you are frustrated but hang in there you will get it. Joe -----Original Message----- Eric, thanks for your reply, but I tried your suggestions and of course they didn't work. As far as I'm concerned, Microsoft can take their network wizard and shove it up Bill Gates' ass. Bob -----Original Message----- Greetings Bob, Make sure the XP's firewall is disabled. It will block file and printer sharing by default. If you installed a third party firewall such as ZoneAlarm, Sygate, or Norton make sure it is properly configured for the network. Ensure NetBIOS over TCP/IP is enabled. Details here. Enable NetBIOS Over TCP/IP (NetBT) http://www.practicallynetworked.com/sharing/troubles h oo t/ netbt.htm __________________ Eric "Bob" wrote in message ... I have tried dozens of times to get my two computers to network, but I have had no luck. I have run the Windows XP netork wizard (if you want to call it that), but EVERYTIME I run it, it fails to set up the wizard. I keep getting the following message when I try to View the workgroup computers-- Mshome is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permission. The list of servers for this workgroup is not currently available. Any clues as to what I can do to get this network to work? Obviously Windows XP does not work well for networking! . . . . . . |
#10
|
|||
|
|||
Networking two computers
Bob,
So I want you to tell me this please. Does your router have a hardware firewall built in it? Second if not do you know how to share files? Lets take the laptop and go from there. make your way to network connections and then right click on that connection go to properties and then to the advanced tab. See if your fire wall is up? Do this please for me and tell me on both PC's Then tell me the IP address of each PC NIC's that is being assigned by the router. Your Problem sounds as if it is the router not XP. You cannot be the only one on the planet that cannot network XP I am doing greater things than this as are a lot of others. Hang in there. We will get it Joe -----Original Message----- Joe, Maybe I should give you more information about my situation. I have been connected to the internet for years. Each computer can connect on their own. I have a cable modem. The router is connected to the modem and then each computer is connected to the router. I have a desktop and a laptop. Each computer connects separately, but I cannot share files between the two computers. I have tried the "wizard" as Microsoft calls it, and I have tried it using every single configuration they offer. No matter what I try, it doesn't work. The computers can't find each other, and then I keep getting error messages telling me to run the wizard again. Hopefully I have provided enough information to give you more insight. Please refer to my original post to see the error message I keep getting. Thanks, Bob -----Original Message----- Glad to see your back. So you have never been able to connect to the internet? Ok is there a main PC or does your internet connection come from the wall per se" into the router? I suggest that you have your internet connection from your ISP (from the wall) go directly into your PC and then add another NIC card going out to your router or just install a wireless nic and one inside your laptop. Another configuration is this. If all you have are two PC's 1 desktop and 1 laptop It should work with the router Like this: Into the router from your cable modem/ISP/Wall make sure you are using the correct port on the router (there is only one for incoming) and then the following cables or wireles out of the router (outgoing) Think about trying to connect without using the wizard an see what you get. Just another test here Bob: plug the internet connection from the wall into the router and then plug a cable out of the router into the laptop or PC just one of them and see if you can get to the net. I do not know exactly how you want to network so I am assuming you want all your PC's to access the net via the router. Joe -----Original Message----- Joe, what do you mean by your question? I'm not sure what you mean, but I'll try to answer it. I am using a router and I have a desktop and laptop. The network wizard in XP is doing absolutely nothing to help me. I keep getting error messages when I try to run the wizard, the computers can't find each other, it cannot find MSHOME. I have tried to run the wizard at least a couple dozen times over the past year and a half, and it NEVER works. You think I'm frustrated? I passed frustrated about 6 months ago. Thanks, Bob -----Original Message----- How are you connecting the PC's Bob? with what type of hardware? and please calm down I know you are frustrated but hang in there you will get it. Joe -----Original Message----- Eric, thanks for your reply, but I tried your suggestions and of course they didn't work. As far as I'm concerned, Microsoft can take their network wizard and shove it up Bill Gates' ass. Bob -----Original Message----- Greetings Bob, Make sure the XP's firewall is disabled. It will block file and printer sharing by default. If you installed a third party firewall such as ZoneAlarm, Sygate, or Norton make sure it is properly configured for the network. Ensure NetBIOS over TCP/IP is enabled. Details here. Enable NetBIOS Over TCP/IP (NetBT) http://www.practicallynetworked.com/sharing/troublesh oo t/ netbt.htm __________________ Eric "Bob" wrote in message ... I have tried dozens of times to get my two computers to network, but I have had no luck. I have run the Windows XP netork wizard (if you want to call it that), but EVERYTIME I run it, it fails to set up the wizard. I keep getting the following message when I try to View the workgroup computers-- Mshome is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permission. The list of servers for this workgroup is not currently available. Any clues as to what I can do to get this network to work? Obviously Windows XP does not work well for networking! . . . . . . |
#11
|
|||
|
|||
Networking two computers
Joe,
my router does have a firewall built in. I have disabled the firewall in XP on both computers. Yes, I know how to set up the file sharing. The IP address on the laptop is 192.168.2.3 The IP address on the desktop is 192.168.2.4 As far as me being the only person on the planet to have a problem networking in XP, I have to disagree with that. As I am looking through the other posts in this newsgroup, I am seeing quite a few people that are having networking problems. Thanks again, Bob -----Original Message----- Bob, So I want you to tell me this please. Does your router have a hardware firewall built in it? Second if not do you know how to share files? Lets take the laptop and go from there. make your way to network connections and then right click on that connection go to properties and then to the advanced tab. See if your fire wall is up? Do this please for me and tell me on both PC's Then tell me the IP address of each PC NIC's that is being assigned by the router. Your Problem sounds as if it is the router not XP. You cannot be the only one on the planet that cannot network XP I am doing greater things than this as are a lot of others. Hang in there. We will get it Joe -----Original Message----- Joe, Maybe I should give you more information about my situation. I have been connected to the internet for years. Each computer can connect on their own. I have a cable modem. The router is connected to the modem and then each computer is connected to the router. I have a desktop and a laptop. Each computer connects separately, but I cannot share files between the two computers. I have tried the "wizard" as Microsoft calls it, and I have tried it using every single configuration they offer. No matter what I try, it doesn't work. The computers can't find each other, and then I keep getting error messages telling me to run the wizard again. Hopefully I have provided enough information to give you more insight. Please refer to my original post to see the error message I keep getting. Thanks, Bob -----Original Message----- Glad to see your back. So you have never been able to connect to the internet? Ok is there a main PC or does your internet connection come from the wall per se" into the router? I suggest that you have your internet connection from your ISP (from the wall) go directly into your PC and then add another NIC card going out to your router or just install a wireless nic and one inside your laptop. Another configuration is this. If all you have are two PC's 1 desktop and 1 laptop It should work with the router Like this: Into the router from your cable modem/ISP/Wall make sure you are using the correct port on the router (there is only one for incoming) and then the following cables or wireles out of the router (outgoing) Think about trying to connect without using the wizard an see what you get. Just another test here Bob: plug the internet connection from the wall into the router and then plug a cable out of the router into the laptop or PC just one of them and see if you can get to the net. I do not know exactly how you want to network so I am assuming you want all your PC's to access the net via the router. Joe -----Original Message----- Joe, what do you mean by your question? I'm not sure what you mean, but I'll try to answer it. I am using a router and I have a desktop and laptop. The network wizard in XP is doing absolutely nothing to help me. I keep getting error messages when I try to run the wizard, the computers can't find each other, it cannot find MSHOME. I have tried to run the wizard at least a couple dozen times over the past year and a half, and it NEVER works. You think I'm frustrated? I passed frustrated about 6 months ago. Thanks, Bob -----Original Message----- How are you connecting the PC's Bob? with what type of hardware? and please calm down I know you are frustrated but hang in there you will get it. Joe -----Original Message----- Eric, thanks for your reply, but I tried your suggestions and of course they didn't work. As far as I'm concerned, Microsoft can take their network wizard and shove it up Bill Gates' ass. Bob -----Original Message----- Greetings Bob, Make sure the XP's firewall is disabled. It will block file and printer sharing by default. If you installed a third party firewall such as ZoneAlarm, Sygate, or Norton make sure it is properly configured for the network. Ensure NetBIOS over TCP/IP is enabled. Details here. Enable NetBIOS Over TCP/IP (NetBT) http://www.practicallynetworked.com/sharing/trouble sh oo t/ netbt.htm __________________ Eric "Bob" wrote in message l... I have tried dozens of times to get my two computers to network, but I have had no luck. I have run the Windows XP netork wizard (if you want to call it that), but EVERYTIME I run it, it fails to set up the wizard. I keep getting the following message when I try to View the workgroup computers-- Mshome is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permission. The list of servers for this workgroup is not currently available. Any clues as to what I can do to get this network to work? Obviously Windows XP does not work well for networking! . . . . . . . |
#12
|
|||
|
|||
Networking two computers
Joe,
my router does have a firewall built in. I have disabled the firewall in XP on both computers. Yes, I know how to set up the file sharing. The IP address on the laptop is 192.168.2.3 The IP address on the desktop is 192.168.2.4 As far as me being the only person on the planet to have a problem networking in XP, I have to disagree with that. As I am looking through the other posts in this newsgroup, I am seeing quite a few people that are having networking problems. Thanks again, Bob -----Original Message----- Bob, So I want you to tell me this please. Does your router have a hardware firewall built in it? Second if not do you know how to share files? Lets take the laptop and go from there. make your way to network connections and then right click on that connection go to properties and then to the advanced tab. See if your fire wall is up? Do this please for me and tell me on both PC's Then tell me the IP address of each PC NIC's that is being assigned by the router. Your Problem sounds as if it is the router not XP. You cannot be the only one on the planet that cannot network XP I am doing greater things than this as are a lot of others. Hang in there. We will get it Joe -----Original Message----- Joe, Maybe I should give you more information about my situation. I have been connected to the internet for years. Each computer can connect on their own. I have a cable modem. The router is connected to the modem and then each computer is connected to the router. I have a desktop and a laptop. Each computer connects separately, but I cannot share files between the two computers. I have tried the "wizard" as Microsoft calls it, and I have tried it using every single configuration they offer. No matter what I try, it doesn't work. The computers can't find each other, and then I keep getting error messages telling me to run the wizard again. Hopefully I have provided enough information to give you more insight. Please refer to my original post to see the error message I keep getting. Thanks, Bob -----Original Message----- Glad to see your back. So you have never been able to connect to the internet? Ok is there a main PC or does your internet connection come from the wall per se" into the router? I suggest that you have your internet connection from your ISP (from the wall) go directly into your PC and then add another NIC card going out to your router or just install a wireless nic and one inside your laptop. Another configuration is this. If all you have are two PC's 1 desktop and 1 laptop It should work with the router Like this: Into the router from your cable modem/ISP/Wall make sure you are using the correct port on the router (there is only one for incoming) and then the following cables or wireles out of the router (outgoing) Think about trying to connect without using the wizard an see what you get. Just another test here Bob: plug the internet connection from the wall into the router and then plug a cable out of the router into the laptop or PC just one of them and see if you can get to the net. I do not know exactly how you want to network so I am assuming you want all your PC's to access the net via the router. Joe -----Original Message----- Joe, what do you mean by your question? I'm not sure what you mean, but I'll try to answer it. I am using a router and I have a desktop and laptop. The network wizard in XP is doing absolutely nothing to help me. I keep getting error messages when I try to run the wizard, the computers can't find each other, it cannot find MSHOME. I have tried to run the wizard at least a couple dozen times over the past year and a half, and it NEVER works. You think I'm frustrated? I passed frustrated about 6 months ago. Thanks, Bob -----Original Message----- How are you connecting the PC's Bob? with what type of hardware? and please calm down I know you are frustrated but hang in there you will get it. Joe -----Original Message----- Eric, thanks for your reply, but I tried your suggestions and of course they didn't work. As far as I'm concerned, Microsoft can take their network wizard and shove it up Bill Gates' ass. Bob -----Original Message----- Greetings Bob, Make sure the XP's firewall is disabled. It will block file and printer sharing by default. If you installed a third party firewall such as ZoneAlarm, Sygate, or Norton make sure it is properly configured for the network. Ensure NetBIOS over TCP/IP is enabled. Details here. Enable NetBIOS Over TCP/IP (NetBT) http://www.practicallynetworked.com/sharing/trouble sh oo t/ netbt.htm __________________ Eric "Bob" wrote in message l... I have tried dozens of times to get my two computers to network, but I have had no luck. I have run the Windows XP netork wizard (if you want to call it that), but EVERYTIME I run it, it fails to set up the wizard. I keep getting the following message when I try to View the workgroup computers-- Mshome is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permission. The list of servers for this workgroup is not currently available. Any clues as to what I can do to get this network to work? Obviously Windows XP does not work well for networking! . . . . . . . |
#13
|
|||
|
|||
Networking two computers
Nick,
I appreciate the time you put into your response, but I must say that the length of your answer only substantiates my opinion that the Windows XP "wizard" is just the opposite. If I have to go through all of that to get a network set up, how the heck can they call it a wizard?? After having spent hours attempting to set this thing up only to get one error after another, I am absolutely certain that there has to be an easier way to do this, and Microsoft does not use that way! thanks again, Bob -----Original Message----- What are the IPs of each of the computers? Are you able to manually enter a shortcut to the other computer in the form: \\Desktop\Shared or \\Laptop\Shared Where Shared is the name of a folder on that computer that is set to be shared on the network. If you want to get the two computers to be networked safely, you need to have them both with the same first 3 sections of the IP address, i.e. 192.168.1.xx and the router should have a connection to the cable modem. I have set up several networks with XP on networks with anywhere from 2 to 15 computers using either a single router or a switch or 3 routers daisy chained together. Once I got the routers set up to properly, I just ran the network setup wizard for each computer and I was up and running. Try starting from scratch. Unplug everything. EVERYTHING. Connect the power to the router and then press and hold the reset button for 30 seconds (there should be one on the back or the bottom). Find the instructions that came with the router (or find them of the router manufacturer's website) and follow them step by step. While you're setting everything up, only have ONE computer connected, once the router is configured properly, connect the other computer. Make sure that you have the router set to act as a DHCP server. Check the IP addresses of each computer. Check this both from "ipconfig /all" in the command prompt and in the router's DHCP configuration menu. The computers should have the exact same subnet mask and the first 3 parts of the IP addresses the same, i.e 192.168.1.xx. If this doesn't fit, then you're never going to get the Windows Network Setup Wizard to work. Once you've got the IPs and subnet masks described above, NOW run the setup wizard. Make sure that you input the exact same settings into each computer. Share a folder and see if you can make a shortcut to that folder in the form \\computer\folder If this still doesn't work (and you've actually followed everything that I've said here), let us know. Hope this helps, Nick nkjg/at\interchange/dot\ubc/dot\ca "The definition of insanity: doing the same thing over and over expecting different results." -----Original Message----- Joe, Maybe I should give you more information about my situation. I have been connected to the internet for years. Each computer can connect on their own. I have a cable modem. The router is connected to the modem and then each computer is connected to the router. I have a desktop and a laptop. Each computer connects separately, but I cannot share files between the two computers. I have tried the "wizard" as Microsoft calls it, and I have tried it using every single configuration they offer. No matter what I try, it doesn't work. The computers can't find each other, and then I keep getting error messages telling me to run the wizard again. Hopefully I have provided enough information to give you more insight. Please refer to my original post to see the error message I keep getting. Thanks, Bob -----Original Message----- Glad to see your back. So you have never been able to connect to the internet? Ok is there a main PC or does your internet connection come from the wall per se" into the router? I suggest that you have your internet connection from your ISP (from the wall) go directly into your PC and then add another NIC card going out to your router or just install a wireless nic and one inside your laptop. Another configuration is this. If all you have are two PC's 1 desktop and 1 laptop It should work with the router Like this: Into the router from your cable modem/ISP/Wall make sure you are using the correct port on the router (there is only one for incoming) and then the following cables or wireles out of the router (outgoing) Think about trying to connect without using the wizard an see what you get. Just another test here Bob: plug the internet connection from the wall into the router and then plug a cable out of the router into the laptop or PC just one of them and see if you can get to the net. I do not know exactly how you want to network so I am assuming you want all your PC's to access the net via the router. Joe -----Original Message----- Joe, what do you mean by your question? I'm not sure what you mean, but I'll try to answer it. I am using a router and I have a desktop and laptop. The network wizard in XP is doing absolutely nothing to help me. I keep getting error messages when I try to run the wizard, the computers can't find each other, it cannot find MSHOME. I have tried to run the wizard at least a couple dozen times over the past year and a half, and it NEVER works. You think I'm frustrated? I passed frustrated about 6 months ago. Thanks, Bob -----Original Message----- How are you connecting the PC's Bob? with what type of hardware? and please calm down I know you are frustrated but hang in there you will get it. Joe -----Original Message----- Eric, thanks for your reply, but I tried your suggestions and of course they didn't work. As far as I'm concerned, Microsoft can take their network wizard and shove it up Bill Gates' ass. Bob -----Original Message----- Greetings Bob, Make sure the XP's firewall is disabled. It will block file and printer sharing by default. If you installed a third party firewall such as ZoneAlarm, Sygate, or Norton make sure it is properly configured for the network. Ensure NetBIOS over TCP/IP is enabled. Details here. Enable NetBIOS Over TCP/IP (NetBT) http://www.practicallynetworked.com/sharing/trouble s h oo t/ netbt.htm __________________ Eric "Bob" wrote in message l... I have tried dozens of times to get my two computers to network, but I have had no luck. I have run the Windows XP netork wizard (if you want to call it that), but EVERYTIME I run it, it fails to set up the wizard. I keep getting the following message when I try to View the workgroup computers-- Mshome is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permission. The list of servers for this workgroup is not currently available. Any clues as to what I can do to get this network to work? Obviously Windows XP does not work well for networking! . . . . . . . |
#14
|
|||
|
|||
Networking two computers
Nick,
I appreciate the time you put into your response, but I must say that the length of your answer only substantiates my opinion that the Windows XP "wizard" is just the opposite. If I have to go through all of that to get a network set up, how the heck can they call it a wizard?? After having spent hours attempting to set this thing up only to get one error after another, I am absolutely certain that there has to be an easier way to do this, and Microsoft does not use that way! thanks again, Bob -----Original Message----- What are the IPs of each of the computers? Are you able to manually enter a shortcut to the other computer in the form: \\Desktop\Shared or \\Laptop\Shared Where Shared is the name of a folder on that computer that is set to be shared on the network. If you want to get the two computers to be networked safely, you need to have them both with the same first 3 sections of the IP address, i.e. 192.168.1.xx and the router should have a connection to the cable modem. I have set up several networks with XP on networks with anywhere from 2 to 15 computers using either a single router or a switch or 3 routers daisy chained together. Once I got the routers set up to properly, I just ran the network setup wizard for each computer and I was up and running. Try starting from scratch. Unplug everything. EVERYTHING. Connect the power to the router and then press and hold the reset button for 30 seconds (there should be one on the back or the bottom). Find the instructions that came with the router (or find them of the router manufacturer's website) and follow them step by step. While you're setting everything up, only have ONE computer connected, once the router is configured properly, connect the other computer. Make sure that you have the router set to act as a DHCP server. Check the IP addresses of each computer. Check this both from "ipconfig /all" in the command prompt and in the router's DHCP configuration menu. The computers should have the exact same subnet mask and the first 3 parts of the IP addresses the same, i.e 192.168.1.xx. If this doesn't fit, then you're never going to get the Windows Network Setup Wizard to work. Once you've got the IPs and subnet masks described above, NOW run the setup wizard. Make sure that you input the exact same settings into each computer. Share a folder and see if you can make a shortcut to that folder in the form \\computer\folder If this still doesn't work (and you've actually followed everything that I've said here), let us know. Hope this helps, Nick nkjg/at\interchange/dot\ubc/dot\ca "The definition of insanity: doing the same thing over and over expecting different results." -----Original Message----- Joe, Maybe I should give you more information about my situation. I have been connected to the internet for years. Each computer can connect on their own. I have a cable modem. The router is connected to the modem and then each computer is connected to the router. I have a desktop and a laptop. Each computer connects separately, but I cannot share files between the two computers. I have tried the "wizard" as Microsoft calls it, and I have tried it using every single configuration they offer. No matter what I try, it doesn't work. The computers can't find each other, and then I keep getting error messages telling me to run the wizard again. Hopefully I have provided enough information to give you more insight. Please refer to my original post to see the error message I keep getting. Thanks, Bob -----Original Message----- Glad to see your back. So you have never been able to connect to the internet? Ok is there a main PC or does your internet connection come from the wall per se" into the router? I suggest that you have your internet connection from your ISP (from the wall) go directly into your PC and then add another NIC card going out to your router or just install a wireless nic and one inside your laptop. Another configuration is this. If all you have are two PC's 1 desktop and 1 laptop It should work with the router Like this: Into the router from your cable modem/ISP/Wall make sure you are using the correct port on the router (there is only one for incoming) and then the following cables or wireles out of the router (outgoing) Think about trying to connect without using the wizard an see what you get. Just another test here Bob: plug the internet connection from the wall into the router and then plug a cable out of the router into the laptop or PC just one of them and see if you can get to the net. I do not know exactly how you want to network so I am assuming you want all your PC's to access the net via the router. Joe -----Original Message----- Joe, what do you mean by your question? I'm not sure what you mean, but I'll try to answer it. I am using a router and I have a desktop and laptop. The network wizard in XP is doing absolutely nothing to help me. I keep getting error messages when I try to run the wizard, the computers can't find each other, it cannot find MSHOME. I have tried to run the wizard at least a couple dozen times over the past year and a half, and it NEVER works. You think I'm frustrated? I passed frustrated about 6 months ago. Thanks, Bob -----Original Message----- How are you connecting the PC's Bob? with what type of hardware? and please calm down I know you are frustrated but hang in there you will get it. Joe -----Original Message----- Eric, thanks for your reply, but I tried your suggestions and of course they didn't work. As far as I'm concerned, Microsoft can take their network wizard and shove it up Bill Gates' ass. Bob -----Original Message----- Greetings Bob, Make sure the XP's firewall is disabled. It will block file and printer sharing by default. If you installed a third party firewall such as ZoneAlarm, Sygate, or Norton make sure it is properly configured for the network. Ensure NetBIOS over TCP/IP is enabled. Details here. Enable NetBIOS Over TCP/IP (NetBT) http://www.practicallynetworked.com/sharing/trouble s h oo t/ netbt.htm __________________ Eric "Bob" wrote in message l... I have tried dozens of times to get my two computers to network, but I have had no luck. I have run the Windows XP netork wizard (if you want to call it that), but EVERYTIME I run it, it fails to set up the wizard. I keep getting the following message when I try to View the workgroup computers-- Mshome is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permission. The list of servers for this workgroup is not currently available. Any clues as to what I can do to get this network to work? Obviously Windows XP does not work well for networking! . . . . . . . |
#15
|
|||
|
|||
Networking two computers
Eric,
thanks for your reply, but I tried your suggestions and of course they didn't work. As far as I'm concerned, Microsoft can take their network wizard and shove it up Bill Gates' ass. Bob -----Original Message----- Greetings Bob, Make sure the XP's firewall is disabled. It will block file and printer sharing by default. If you installed a third party firewall such as ZoneAlarm, Sygate, or Norton make sure it is properly configured for the network. Ensure NetBIOS over TCP/IP is enabled. Details here. Enable NetBIOS Over TCP/IP (NetBT) http://www.practicallynetworked.com/.../troubleshoot/ netbt.htm __________________ Eric "Bob" wrote in message ... I have tried dozens of times to get my two computers to network, but I have had no luck. I have run the Windows XP netork wizard (if you want to call it that), but EVERYTIME I run it, it fails to set up the wizard. I keep getting the following message when I try to View the workgroup computers-- Mshome is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permission. The list of servers for this workgroup is not currently available. Any clues as to what I can do to get this network to work? Obviously Windows XP does not work well for networking! . |
Thread Tools | |
Display Modes | |
|
|