If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Add Printer - Operation Cannot be Completed
Posted in general but then realized there was a forum strictly for printing.
Not sure whether the problem began with XP SP3 or as a result of optimizing my hard drive with Norton System Works 2008. Noted after installing Acrobat Pro 9 that it will not pdf any documents as the system would not setup the necessary printers. Tried adding a printer manually and get the Operation Cannot Complete message. The fix to this is to ensure that Print Spooler is running in Services which it is. It both comes on automatically at boot and stays started. I have also attempted to manually shut it down and then start it but to no avail. If it's not the spooler, any suggestions of what it could be. I'd like to avoid reinstall my entire machine alhtough will be attemptinga fix via Windows Repair installation. From another site, I did try a suggested fix to remove the .PNX files, however, this didn't work either. Is there a registry setting that I can adjust to get back Add Priinter? Thanks in advance for any help. |
Ads |
#2
|
|||
|
|||
Add Printer - Operation Cannot be Completed
Personally I'd see if it works again after removing Norton.
-- Cari (MS-MVP) Printing & Imaging www.coribright.com/windows "raydeo" wrote in message ... Posted in general but then realized there was a forum strictly for printing. Not sure whether the problem began with XP SP3 or as a result of optimizing my hard drive with Norton System Works 2008. Noted after installing Acrobat Pro 9 that it will not pdf any documents as the system would not setup the necessary printers. Tried adding a printer manually and get the Operation Cannot Complete message. The fix to this is to ensure that Print Spooler is running in Services which it is. It both comes on automatically at boot and stays started. I have also attempted to manually shut it down and then start it but to no avail. If it's not the spooler, any suggestions of what it could be. I'd like to avoid reinstall my entire machine alhtough will be attemptinga fix via Windows Repair installation. From another site, I did try a suggested fix to remove the .PNX files, however, this didn't work either. Is there a registry setting that I can adjust to get back Add Priinter? Thanks in advance for any help. |
#3
|
|||
|
|||
Add Printer - Operation Cannot be Completed
Didn't work so did an XP Repair insrallation and got it back. Saved havoing
to re-install the entire machine. Of course after the repair, had to register a couple of Windows files as it wouldn't bring down any updates. This time I'll leave off SP3 as it's been more of a hindrance than a help. "Cari (MS-MVP)" wrote: Personally I'd see if it works again after removing Norton. -- Cari (MS-MVP) Printing & Imaging www.coribright.com/windows "raydeo" wrote in message ... Posted in general but then realized there was a forum strictly for printing. Not sure whether the problem began with XP SP3 or as a result of optimizing my hard drive with Norton System Works 2008. Noted after installing Acrobat Pro 9 that it will not pdf any documents as the system would not setup the necessary printers. Tried adding a printer manually and get the Operation Cannot Complete message. The fix to this is to ensure that Print Spooler is running in Services which it is. It both comes on automatically at boot and stays started. I have also attempted to manually shut it down and then start it but to no avail. If it's not the spooler, any suggestions of what it could be. I'd like to avoid reinstall my entire machine alhtough will be attemptinga fix via Windows Repair installation. From another site, I did try a suggested fix to remove the .PNX files, however, this didn't work either. Is there a registry setting that I can adjust to get back Add Priinter? Thanks in advance for any help. |
Thread Tools | |
Display Modes | |
|
|