If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
corrupt system restore points
Whenver I do a system restore to a previous date, the system restore feature goes through its routines then on startup it says the the restore was unsuccessful. I suspect the restore points are corrupted - is there any way to restore my computer to a previous date using system restore now?
Thanks s |
Ads |
#2
|
|||
|
|||
corrupt system restore points
there is a way to force it but it is not recommencded.
The steps can be found i the microsoft knowledge base ... and i'm not pointing the way to your slaughter -----Original Message----- Whenver I do a system restore to a previous date, the system restore feature goes through its routines then on startup it says the the restore was unsuccessful. I suspect the restore points are corrupted - is there any way to restore my computer to a previous date using system restore now? Thanks s . |
#3
|
|||
|
|||
corrupt system restore points
Unfortunately once system restore get's corrupted you can't repair it.
The only solution is to turn off system restore then turn it back on again. That will remove all restore points and start fresh. To do so right click on My computer, choose properties, then the system restore tab. Tick mark Turn off System Restore. Click ok and reboot. Then go to the System Volume Information folder on each drive and delete the contents. You will need to make sure that it is set to show hidden files by going to My computer, tools, folder options, view. After deleting the files in the System Volume Informaton folder retrace the steps to remove the tick mark in turn off system restore. System restore only needs to be active on the drive where windows is installed, normally the C drive and drives where programs are installed. No need to have it monitoring on data only drives. The option to turn off monitoring on certain drives is in that same window. After turning it bck on, then reboot. sonic wrote: Whenver I do a system restore to a previous date, the system restore feature goes through its routines then on startup it says the the restore was unsuccessful. I suspect the restore points are corrupted - is there any way to restore my computer to a previous date using system restore now? Thanks s |
#4
|
|||
|
|||
corrupt system restore points
|
#5
|
|||
|
|||
corrupt system restore points
One other thing. System restore, by default, uses a huge amount of
space, by % of the hard disk space available. That can mean way too much on a large drive. So in system restore under settings for each drive reduce the amount of space allocated. 500MB is a good amount. sonic wrote: Whenver I do a system restore to a previous date, the system restore feature goes through its routines then on startup it says the the restore was unsuccessful. I suspect the restore points are corrupted - is there any way to restore my computer to a previous date using system restore now? Thanks s |
#6
|
|||
|
|||
corrupt system restore points
I'm fascinated. Can you provide a link or description of the article?
wrote in message ... there is a way to force it but it is not recommencded. The steps can be found i the microsoft knowledge base ... and i'm not pointing the way to your slaughter -----Original Message----- Whenver I do a system restore to a previous date, the system restore feature goes through its routines then on startup it says the the restore was unsuccessful. I suspect the restore points are corrupted - is there any way to restore my computer to a previous date using system restore now? Thanks s . |
#7
|
|||
|
|||
corrupt system restore points
Is it safe to delete RP folders in system volume information? You are saying that I should delete everything in the system volume information folder. Will turning the system restore off (and thus deleting all past restore points) delete everything in the system volume folder or should I delete eveything in there manually - currently it is using up over 7 GB on my HD and I would like to free up a lot of space, so should I delete thes folders manually. Also, if I know the date that I corrupted my restore point can I delete the RP folder that applies to that day. Will my previous system restore points then work again after I remove the corrupt day's RP folder in Sys VOl Info Folder. Please let me know.
Thanks "Rock" wrote: One other thing. System restore, by default, uses a huge amount of space, by % of the hard disk space available. That can mean way too much on a large drive. So in system restore under settings for each drive reduce the amount of space allocated. 500MB is a good amount. sonic wrote: Whenver I do a system restore to a previous date, the system restore feature goes through its routines then on startup it says the the restore was unsuccessful. I suspect the restore points are corrupted - is there any way to restore my computer to a previous date using system restore now? Thanks s |
#8
|
|||
|
|||
corrupt system restore points
sonic wrote:
Is it safe to delete RP folders in system volume information? You are saying that I should delete everything in the system volume information folder. Will turning the system restore off (and thus deleting all past restore points) delete everything in the system volume folder or should I delete eveything in there manually - currently it is using up over 7 GB on my HD and I would like to free up a lot of space, so should I delete thes folders manually. Also, if I know the date that I corrupted my restore point can I delete the RP folder that applies to that day. Will my previous system restore points then work again after I remove the corrupt day's RP folder in Sys VOl Info Folder. Please let me know. Thanks "Rock" wrote: One other thing. System restore, by default, uses a huge amount of space, by % of the hard disk space available. That can mean way too much on a large drive. So in system restore under settings for each drive reduce the amount of space allocated. 500MB is a good amount. sonic wrote: Whenver I do a system restore to a previous date, the system restore feature goes through its routines then on startup it says the the restore was unsuccessful. I suspect the restore points are corrupted - is there any way to restore my computer to a previous date using system restore now? Thanks s Turning off system restore should delete the restore points in that folder. Checking manually after turning it off is just being thorough in case something was corrupted and didn't get deleted when you turned of system restore. No you can't selectively delete just one restore point. It's all or none. Actually using the disc cleanup function deletes all but the most recent restore point. Turning off system restore deletes them all. There is no way to remove just one. They work as links in a chain. To restore to a past date requires all those restore points created after that date to work. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
System Restore Point versus System Checkpoint | The Unknown P | General XP issues or comments | 17 | July 30th 04 08:22 PM |
ShutDown Problem, Reinstall? | Ron Eggler | General XP issues or comments | 57 | July 30th 04 07:52 PM |
once you get to the registry | tudrussell | General XP issues or comments | 62 | July 27th 04 07:53 AM |
About system restore | George | The Basics | 1 | July 26th 04 09:41 AM |
Help Restoring Registry | paton(removeme)@cablespeed.com | General XP issues or comments | 9 | July 16th 04 10:54 PM |