A Windows XP help forum. PCbanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » PCbanter forum » Windows 10 » Windows 10 Help Forum
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

cranky enet connection upon boot



 
 
Thread Tools Rate Thread Display Modes
  #1  
Old March 14th 19, 12:48 AM posted to alt.comp.os.windows-10
Jason
external usenet poster
 
Posts: 242
Default cranky enet connection upon boot

My deskside machine has wired ethernet to my router. It has
forever been the case that Windows latches onto the network at
boot every time with no problems until now. I cannot think of
anything I have changed. Perhaps this is the result of an
update, but now when I boot the machine the network connection
does not take place and I have to fiddle with disabling/enabling
the adapter a few times before it does connect. That's not a big
problem, but I'm curious what might cause it. ...and it is not
quite consistent - about one time in five it connects instantly
just like it used to. Hardware diagnostics don't show anything.

Ads
  #2  
Old March 14th 19, 01:51 AM posted to alt.comp.os.windows-10
Char Jackson
external usenet poster
 
Posts: 10,449
Default cranky enet connection upon boot

On Wed, 13 Mar 2019 19:48:01 -0400, Jason
wrote:

My deskside machine has wired ethernet to my router. It has
forever been the case that Windows latches onto the network at
boot every time with no problems until now. I cannot think of
anything I have changed. Perhaps this is the result of an
update, but now when I boot the machine the network connection
does not take place and I have to fiddle with disabling/enabling
the adapter a few times before it does connect. That's not a big
problem, but I'm curious what might cause it. ...and it is not
quite consistent - about one time in five it connects instantly
just like it used to. Hardware diagnostics don't show anything.


Do you have a router? Are you using DHCP? Are you using address
reservation, or whatever your router calls it? When it doesn't connect,
what is your IP address? Is it in the range of 169.254.x.y? Do you have
any other network devices on your LAN? If so, do any of them sometimes
display similar behavior?

If you're using a router and it's configured to use DHCP and the PC ends
up with a 169.254.x.y address, the problem could be the PC or the
router. You can work around that particular issue by configuring a
static IP address (plus netmask, default gateway, and DNS servers) on
your PC. If you set static values, it's one and done. You just need to
take care to assign an IP address that's within your current subnet but
not within your DHCP scope.

The trick is to take a look at your networking info while you're
experiencing the issue. Once you've resolved the issue, it's too late to
do much troubleshooting. Command Prompt "ifconfig /all" would be a good
start, or you can poke around in "Network and Internet Settings", then
"Change Adapter Options", pick the adapter, then select Status from the
context menu.

  #4  
Old March 14th 19, 04:26 PM posted to alt.comp.os.windows-10
Char Jackson
external usenet poster
 
Posts: 10,449
Default cranky enet connection upon boot

On Thu, 14 Mar 2019 10:59:44 -0400, Jason
wrote:

In article ,
says...
The trick is to take a look at your networking info while you're
experiencing the issue. Once you've resolved the issue, it's too late to
do much troubleshooting.


That's excellent advice (as is the rest you provided). I'll take a look
next time it's broken at startup. Thanks.


You're welcome. Good luck.

  #5  
Old March 14th 19, 04:40 PM posted to alt.comp.os.windows-10
Jonathan N. Little[_2_]
external usenet poster
 
Posts: 1,133
Default cranky enet connection upon boot

Jason wrote:
My deskside machine has wired ethernet to my router. It has
forever been the case that Windows latches onto the network at
boot every time with no problems until now. I cannot think of
anything I have changed. Perhaps this is the result of an
update, but now when I boot the machine the network connection
does not take place and I have to fiddle with disabling/enabling
the adapter a few times before it does connect. That's not a big
problem, but I'm curious what might cause it. ...and it is not
quite consistent - about one time in five it connects instantly
just like it used to. Hardware diagnostics don't show anything.


Well the first thing I do is test the cable. Most most folks don't have
a test handy but my advise is always have a spare cable to test.

If you unplug cable and reinsert it does the connection connect
immediately? If so maybe the wire connector is loose or damaged.

Next what happens if from a CMD windows you renew the DHCP lease with:

ipconfig /renew

--
Take care,

Jonathan
-------------------
LITTLE WORKS STUDIO
http://www.LittleWorksStudio.com
  #6  
Old March 15th 19, 01:49 AM posted to alt.comp.os.windows-10
n/a
external usenet poster
 
Posts: 75
Default TYPO cranky enet connection upon boot

"Jason" wrote in message
...

In article ,
says...
The trick is to take a look at your networking info while you're
experiencing the issue. Once you've resolved the issue, it's too late to
do much troubleshooting.


That's excellent advice (as is the rest you provided). I'll take a look
next time it's broken at startup. Thanks.



There's a typo - use ipconfig /all
--
Bob S.

  #7  
Old March 15th 19, 03:24 AM posted to alt.comp.os.windows-10
Char Jackson
external usenet poster
 
Posts: 10,449
Default TYPO cranky enet connection upon boot

On Thu, 14 Mar 2019 20:49:08 -0400, "n/a" wrote:

"Jason" wrote in message
al-september.org...

In article ,
says...
The trick is to take a look at your networking info while you're
experiencing the issue. Once you've resolved the issue, it's too late to
do much troubleshooting.


That's excellent advice (as is the rest you provided). I'll take a look
next time it's broken at startup. Thanks.



There's a typo - use ipconfig /all


Good catch, thanks.


 




Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off






All times are GMT +1. The time now is 07:19 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 PCbanter.
The comments are property of their posters.