I am in a deep trouble, help

Dear all,

I get my PC permanently reboots after a service pack gets applied.
I have try anything I have find out the web based on this issue but no luck.
Even when I was trying to enter the recovery console, when selecting the
operating system to enter, then it reboots.

So as a lst chance I have started to repair boot system files by booting
from original Cd and then press ener to istall windows and then pres R on the
existing installation found. So far so good except that at the timeit reboot
to restart normally, I am prompt with the following message :

"The file 'asms' of the Service Pack 1 CD for Windows XP professionnal is
needed".

I do not have this CD in hands and cannot continue .

I have download the ISO image of the Win Pro XP1 (250 mb) and burn it, and
try it but no luck, the CD or the content is not recognized.

Does anyone could prompt me to proper ISO file for doanlowd and the way to
name or burn the CD in order it is recognozed ?

I need the french version of if

Thnaks for help
regards
serge
serge

calderara wrote:
Dear all,

I get my PC permanently reboots after a service pack gets applied.
I have try anything I have find out the web based on this issue but no luck.
Even when I was trying to enter the recovery console, when selecting the
operating system to enter, then it reboots.

So as a lst chance I have started to repair boot system files by booting
from original Cd and then press ener to istall windows and then pres R on the
existing installation found. So far so good except that at the timeit reboot
to restart normally, I am prompt with the following message :

"The file 'asms' of the Service Pack 1 CD for Windows XP professionnal is
needed".

I do not have this CD in hands and cannot continue .

I have download the ISO image of the Win Pro XP1 (250 mb) and burn it, and
try it but no luck, the CD or the content is not recognized.

Does anyone could prompt me to proper ISO file for doanlowd and the way to
name or burn the CD in order it is recognozed ?

I need the french version of if

Thnaks for help
regards
serge
serge
Is the pc powered by AMD processor? I Googled "windowsxp reboot loop
sp3" and got a bunch of resources. Try this one to start:
http://www.infoworld.com/d/mobilize/...get-out-it-379

Assuming you just installed SP3...

Error message after you upgrade a computer that uses a processor other than
an Intel processor to Windows XP Service Pack 2 or to Windows XP Service
Pack 3: "STOP: 0x0000007E":
http://support.microsoft.com/kb/953356


calderara wrote:
Dear all,

I get my PC permanently reboots after a service pack gets applied.
I have try anything I have find out the web based on this issue but no
luck.
Even when I was trying to enter the recovery console, when selecting the
operating system to enter, then it reboots.

So as a lst chance I have started to repair boot system files by booting
from original Cd and then press ener to istall windows and then pres R on
the existing installation found. So far so good except that at the timeit
reboot to restart normally, I am prompt with the following message :

"The file 'asms' of the Service Pack 1 CD for Windows XP professionnal is
needed".

I do not have this CD in hands and cannot continue .

I have download the ISO image of the Win Pro XP1 (250 mb) and burn it, and
try it but no luck, the CD or the content is not recognized.

Does anyone could prompt me to proper ISO file for doanlowd and the way to
name or burn the CD in order it is recognozed ?

I need the french version of if

Thnaks for help
regards
serge
serge

Make certain that your disk drive has the space required, at least 2GB for a
PC that is fully loaded with applications. This 2GB does not include the
recommended 15% free disk space requirement for Windows XP.

Install SP3 in 'Clean Boot' mode:
How to configure Windows XP to start in a "clean boot" state
http://support.microsoft.com/kb/310353
See the section titled: Manual steps to perform a clean boot in Windows XP,
skipping step 4.

Why clean boot:
A "Clean Boot" insures that only a minimal set of Windows Services and
applications are running. This means your Anti Virus software, third party
Firewall and other background applications will not be running; thereby
reducing the chances that installing SP3 will fail. Just remember to undo
the "Clean Boot" changes after installing SP3.

Do not use the Windows Update web site, if at all possible download the
service pack installation file directly to your hard drive and install SP3
using the file you downloaded.

Where to download the SP3 installation file:
(File is large but will only install components that your PC requires)
http://www.microsoft.com/downloads/d...DisplayLang=en

Steps to take before you install Windows XP Service Pack 3
Recommends steps to take before you install Windows XP Service Pack 3.
Also includes troubleshooting information and error codes.
http://support.microsoft.com/kb/950717/en-us

XP SP3: Post Installation Cleanup:
http://www.aumha.net/viewtopic.php?f=62&t=33827

Error message after you upgrade a computer that uses a processor other than
an Intel processor to Windows XP Service Pack 2 or to Windows XP Service
Pack 3: "STOP: 0x0000007E"
http://support.microsoft.com/?kbid=953356
This is the patch to fix the above issue "For non-Intel processors"
***Must be applied before installing SP3***
http://www.microsoft.com/downloads/d...displaylang=en

You receive a "Stop 0x0000007E" error message after you upgrade to Windows
XP Service Pack 2 or Service Pack 3 on a non-Intel-processor-based computer.
http://support.microsoft.com/kb/888372

From: Jesper Johansson's blog
Does your AMD-based computer boot after installing XP SP3?
(Affects AMD-based computers with OEM images, primarily HP Desktops)
http://msinfluentials.com/blogs/jesp...ng-xp-sp3.aspx

--
JS
http://www.pagestart.com



"calderara" wrote in message
...
Dear all,

I get my PC permanently reboots after a service pack gets applied.
I have try anything I have find out the web based on this issue but no
luck.
Even when I was trying to enter the recovery console, when selecting the
operating system to enter, then it reboots.

So as a lst chance I have started to repair boot system files by booting
from original Cd and then press ener to istall windows and then pres R on
the
existing installation found. So far so good except that at the timeit
reboot
to restart normally, I am prompt with the following message :

"The file 'asms' of the Service Pack 1 CD for Windows XP professionnal is
needed".

I do not have this CD in hands and cannot continue .

I have download the ISO image of the Win Pro XP1 (250 mb) and burn it, and
try it but no luck, the CD or the content is not recognized.

Does anyone could prompt me to proper ISO file for doanlowd and the way to
name or burn the CD in order it is recognozed ?

I need the french version of if

Thnaks for help
regards
serge
serge