|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
August 11th 09, 01:56 PM
posted to microsoft.public.windowsxp.network_web
|
|||
|
|||
Can't Map Using UNC
We lost our dirve mappings that were setup using the UNC. I can map
using the IP address. I went to map a drive and preformed a Browse and nothing shows up under the Workgroup for the server we want to map to. Any Ideas? Thanks 
|
| Ads |
|
#2
August 11th 09, 02:11 PM
posted to microsoft.public.windowsxp.network_web
|
|||
|
|||
|
Can't Map Using UNC
On Aug 11, 1:56*pm, Ron Boetger wrote:
We lost our dirve mappings that were setup using the UNC. *I can map using the IP address. I went to map a drive and preformed a Browse and nothing shows up under the Workgroup for the server we want to map to. Any Ideas? Thanks Check all / any firewall settings. Firewalls can block the "NetBIOS name resolution" protocol.
|
|
#3
August 11th 09, 02:11 PM
posted to microsoft.public.windowsxp.network_web
|
|||
|
|||
|
Can't Map Using UNC
On Aug 11, 1:56*pm, Ron Boetger wrote:
We lost our dirve mappings that were setup using the UNC. *I can map using the IP address. I went to map a drive and preformed a Browse and nothing shows up under the Workgroup for the server we want to map to. Any Ideas? Thanks Check all / any firewall settings. Firewalls can block the "NetBIOS name resolution" protocol.
|
|
#4
August 11th 09, 02:27 PM
posted to microsoft.public.windowsxp.network_web
|
|||
|
|||
|
Can't Map Using UNC
I did that and also turned the firewall off. Still no good.
Thanks On Tue, 11 Aug 2009 06:11:32 -0700 (PDT), smlunatick wrote: On Aug 11, 1:56*pm, Ron Boetger wrote: We lost our dirve mappings that were setup using the UNC. *I can map using the IP address. I went to map a drive and preformed a Browse and nothing shows up under the Workgroup for the server we want to map to. Any Ideas? Thanks Check all / any firewall settings. Firewalls can block the "NetBIOS name resolution" protocol.
|
|
#5
August 11th 09, 02:27 PM
posted to microsoft.public.windowsxp.network_web
|
|||
|
|||
|
Can't Map Using UNC
I did that and also turned the firewall off. Still no good.
Thanks On Tue, 11 Aug 2009 06:11:32 -0700 (PDT), smlunatick wrote: On Aug 11, 1:56*pm, Ron Boetger wrote: We lost our dirve mappings that were setup using the UNC. *I can map using the IP address. I went to map a drive and preformed a Browse and nothing shows up under the Workgroup for the server we want to map to. Any Ideas? Thanks Check all / any firewall settings. Firewalls can block the "NetBIOS name resolution" protocol.
|
|
#6
August 11th 09, 03:45 PM
posted to microsoft.public.windowsxp.network_web
|
|||
|
|||
|
Can't Map Using UNC
Verify that the TCP/IP NetBIOS Helper service is running. Issue the NET
VIEW command and report the output of the command in your next post. John Ron Boetger wrote: We lost our dirve mappings that were setup using the UNC. I can map using the IP address. I went to map a drive and preformed a Browse and nothing shows up under the Workgroup for the server we want to map to. Any Ideas? Thanks
|
|
#7
August 11th 09, 03:45 PM
posted to microsoft.public.windowsxp.network_web
|
|||
|
|||
|
Can't Map Using UNC
Verify that the TCP/IP NetBIOS Helper service is running. Issue the NET
VIEW command and report the output of the command in your next post. John Ron Boetger wrote: We lost our dirve mappings that were setup using the UNC. I can map using the IP address. I went to map a drive and preformed a Browse and nothing shows up under the Workgroup for the server we want to map to. Any Ideas? Thanks
|
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
