If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
New Unmanaged Switch Doesn't Connect to Router
Hi, all. Thanks in advance for any help anyone can offer.
Been running an Linksys BEFSR81 wired router, four port. Got a new laptop and need to connect. Bought a TP-Link unmanage five-port router. Connected it by the AC adapter and a new CAT 5e cable going from the laptop to the #1 port of the switch. Supposedly, you don't have to do anything. Well, ran the setup wizards for both the network and the Internet connection and although the icon at the bottom popped up and said I was connected, I cannot connect. The main computers are all running Windows XP Home, SP2, the laptop Windows XP Pro, SP3. I did try plugging an existing connected computer out from the router and plugging it into the switch but it didn't connect either. Then I took the plug that comes in from the cable outside and tried plugging into the switch but that didn't give Internet service either. I am stumped. It may be obvious to someone who knows switches, but I don't and it isn't. I did use the ipconf/all command on the laptop and the only thing I feel is worth mentioning is, it gave a line that said NetBOIOS over Tcpip is disabled, if that means anything. Thanks for any help you can offer. |
Ads |
#2
|
|||
|
|||
New Unmanaged Switch Doesn't Connect to Router
Hi
There is No need for two Routers. If your New Router is Wireless use it instead of the old Router. If you do want to keep two Routers then the second Router has to be connected like this. Using a Wireless Router as a switch with an Access Point - http://www.ezlan.net/router_AP.html Jack (MS, MVP-Networking). "Lori" wrote in message news Hi, all. Thanks in advance for any help anyone can offer. Been running an Linksys BEFSR81 wired router, four port. Got a new laptop and need to connect. Bought a TP-Link unmanage five-port router. Connected it by the AC adapter and a new CAT 5e cable going from the laptop to the #1 port of the switch. Supposedly, you don't have to do anything. Well, ran the setup wizards for both the network and the Internet connection and although the icon at the bottom popped up and said I was connected, I cannot connect. The main computers are all running Windows XP Home, SP2, the laptop Windows XP Pro, SP3. I did try plugging an existing connected computer out from the router and plugging it into the switch but it didn't connect either. Then I took the plug that comes in from the cable outside and tried plugging into the switch but that didn't give Internet service either. I am stumped. It may be obvious to someone who knows switches, but I don't and it isn't. I did use the ipconf/all command on the laptop and the only thing I feel is worth mentioning is, it gave a line that said NetBOIOS over Tcpip is disabled, if that means anything. Thanks for any help you can offer. |
#3
|
|||
|
|||
New Unmanaged Switch Doesn't Connect to Router
Hi
There is No need for two Routers. If your New Router is Wireless use it instead of the old Router. If you do want to keep two Routers then the second Router has to be connected like this. Using a Wireless Router as a switch with an Access Point - http://www.ezlan.net/router_AP.html Jack (MS, MVP-Networking). "Lori" wrote in message news Hi, all. Thanks in advance for any help anyone can offer. Been running an Linksys BEFSR81 wired router, four port. Got a new laptop and need to connect. Bought a TP-Link unmanage five-port router. Connected it by the AC adapter and a new CAT 5e cable going from the laptop to the #1 port of the switch. Supposedly, you don't have to do anything. Well, ran the setup wizards for both the network and the Internet connection and although the icon at the bottom popped up and said I was connected, I cannot connect. The main computers are all running Windows XP Home, SP2, the laptop Windows XP Pro, SP3. I did try plugging an existing connected computer out from the router and plugging it into the switch but it didn't connect either. Then I took the plug that comes in from the cable outside and tried plugging into the switch but that didn't give Internet service either. I am stumped. It may be obvious to someone who knows switches, but I don't and it isn't. I did use the ipconf/all command on the laptop and the only thing I feel is worth mentioning is, it gave a line that said NetBOIOS over Tcpip is disabled, if that means anything. Thanks for any help you can offer. |
#4
|
|||
|
|||
New Unmanaged Switch Doesn't Connect to Router
Jack,
Thanks for the fast reply, but you may have misread my post. I am on a HARD WIRED router for years and added a switch to connect my laptop to the network and provide Internet access. Please re-read it and see if that is what you meant to say. Nothing about this involved more than one router or anything wireless. I have connected the laptop to the switch via CAT 5e cable. Thanks! "Jack (MVP-Networking)." wrote: Hi There is No need for two Routers. If your New Router is Wireless use it instead of the old Router. If you do want to keep two Routers then the second Router has to be connected like this. Using a Wireless Router as a switch with an Access Point - http://www.ezlan.net/router_AP.html Jack (MS, MVP-Networking). "Lori" wrote in message news Hi, all. Thanks in advance for any help anyone can offer. Been running an Linksys BEFSR81 wired router, four port. Got a new laptop and need to connect. Bought a TP-Link unmanage five-port router. Connected it by the AC adapter and a new CAT 5e cable going from the laptop to the #1 port of the switch. Supposedly, you don't have to do anything. Well, ran the setup wizards for both the network and the Internet connection and although the icon at the bottom popped up and said I was connected, I cannot connect. The main computers are all running Windows XP Home, SP2, the laptop Windows XP Pro, SP3. I did try plugging an existing connected computer out from the router and plugging it into the switch but it didn't connect either. Then I took the plug that comes in from the cable outside and tried plugging into the switch but that didn't give Internet service either. I am stumped. It may be obvious to someone who knows switches, but I don't and it isn't. I did use the ipconf/all command on the laptop and the only thing I feel is worth mentioning is, it gave a line that said NetBOIOS over Tcpip is disabled, if that means anything. Thanks for any help you can offer. |
#5
|
|||
|
|||
New Unmanaged Switch Doesn't Connect to Router
Jack,
Thanks for the fast reply, but you may have misread my post. I am on a HARD WIRED router for years and added a switch to connect my laptop to the network and provide Internet access. Please re-read it and see if that is what you meant to say. Nothing about this involved more than one router or anything wireless. I have connected the laptop to the switch via CAT 5e cable. Thanks! "Jack (MVP-Networking)." wrote: Hi There is No need for two Routers. If your New Router is Wireless use it instead of the old Router. If you do want to keep two Routers then the second Router has to be connected like this. Using a Wireless Router as a switch with an Access Point - http://www.ezlan.net/router_AP.html Jack (MS, MVP-Networking). "Lori" wrote in message news Hi, all. Thanks in advance for any help anyone can offer. Been running an Linksys BEFSR81 wired router, four port. Got a new laptop and need to connect. Bought a TP-Link unmanage five-port router. Connected it by the AC adapter and a new CAT 5e cable going from the laptop to the #1 port of the switch. Supposedly, you don't have to do anything. Well, ran the setup wizards for both the network and the Internet connection and although the icon at the bottom popped up and said I was connected, I cannot connect. The main computers are all running Windows XP Home, SP2, the laptop Windows XP Pro, SP3. I did try plugging an existing connected computer out from the router and plugging it into the switch but it didn't connect either. Then I took the plug that comes in from the cable outside and tried plugging into the switch but that didn't give Internet service either. I am stumped. It may be obvious to someone who knows switches, but I don't and it isn't. I did use the ipconf/all command on the laptop and the only thing I feel is worth mentioning is, it gave a line that said NetBOIOS over Tcpip is disabled, if that means anything. Thanks for any help you can offer. |
#6
|
|||
|
|||
New Unmanaged Switch Doesn't Connect to Router
Lori wrote:
Jack, Thanks for the fast reply, but you may have misread my post. I am on a HARD WIRED router for years and added a switch to connect my laptop to the network and provide Internet access. Please re-read it and see if that is what you meant to say. Nothing about this involved more than one router or anything wireless. I have connected the laptop to the switch via CAT 5e cable. Thanks! "Jack (MVP-Networking)." wrote: Hi There is No need for two Routers. If your New Router is Wireless use it instead of the old Router. If you do want to keep two Routers then the second Router has to be connected like this. Using a Wireless Router as a switch with an Access Point - http://www.ezlan.net/router_AP.html Jack (MS, MVP-Networking). "Lori" wrote in message news Hi, all. Thanks in advance for any help anyone can offer. Been running an Linksys BEFSR81 wired router, four port. Got a new laptop and need to connect. Bought a TP-Link unmanage five-port router. Connected it by the AC adapter and a new CAT 5e cable going from the laptop to the #1 port of the switch. Supposedly, you don't have to do anything. Well, ran the setup wizards for both the network and the Internet connection and although the icon at the bottom popped up and said I was connected, I cannot connect. The main computers are all running Windows XP Home, SP2, the laptop Windows XP Pro, SP3. I did try plugging an existing connected computer out from the router and plugging it into the switch but it didn't connect either. Then I took the plug that comes in from the cable outside and tried plugging into the switch but that didn't give Internet service either. I am stumped. It may be obvious to someone who knows switches, but I don't and it isn't. I did use the ipconf/all command on the laptop and the only thing I feel is worth mentioning is, it gave a line that said NetBOIOS over Tcpip is disabled, if that means anything. Thanks for any help you can offer. Perhaps Jack thought your new switch was wireless because you didn't mention that you had connected a patch cable between your old router and the new switch. You did that, of course? When you have the router connected to the switch and the switch connected to the laptop, what else does ipconfig /all report beside NetBIOS disabled? Specifically, what is shown for the laptop's IP address, subnet mask, and gateway IP address? Similarly, what result from ipconfig /all when you connect one of your working computers to the switch (and reboot)? How do those results compare to ipconfig /all run on a computer connected to the router and successfully accessing the Internet? And you should explicitly enable NetBIOS over TCP/IP on all of your computers. Right click on the LAN icon, select Properties; select TCP/IP and click Properties; click Advanced on the General tab; then click the WINS tab. See http://networking.nitecruzr.net/2006...ver-tcpip.html -- Lem -- MS-MVP To the moon and back with 2K words of RAM and 36K words of ROM. http://en.wikipedia.org/wiki/Apollo_Guidance_Computer http://history.nasa.gov/afj/compessay.htm |
#7
|
|||
|
|||
New Unmanaged Switch Doesn't Connect to Router
Lori wrote:
Jack, Thanks for the fast reply, but you may have misread my post. I am on a HARD WIRED router for years and added a switch to connect my laptop to the network and provide Internet access. Please re-read it and see if that is what you meant to say. Nothing about this involved more than one router or anything wireless. I have connected the laptop to the switch via CAT 5e cable. Thanks! "Jack (MVP-Networking)." wrote: Hi There is No need for two Routers. If your New Router is Wireless use it instead of the old Router. If you do want to keep two Routers then the second Router has to be connected like this. Using a Wireless Router as a switch with an Access Point - http://www.ezlan.net/router_AP.html Jack (MS, MVP-Networking). "Lori" wrote in message news Hi, all. Thanks in advance for any help anyone can offer. Been running an Linksys BEFSR81 wired router, four port. Got a new laptop and need to connect. Bought a TP-Link unmanage five-port router. Connected it by the AC adapter and a new CAT 5e cable going from the laptop to the #1 port of the switch. Supposedly, you don't have to do anything. Well, ran the setup wizards for both the network and the Internet connection and although the icon at the bottom popped up and said I was connected, I cannot connect. The main computers are all running Windows XP Home, SP2, the laptop Windows XP Pro, SP3. I did try plugging an existing connected computer out from the router and plugging it into the switch but it didn't connect either. Then I took the plug that comes in from the cable outside and tried plugging into the switch but that didn't give Internet service either. I am stumped. It may be obvious to someone who knows switches, but I don't and it isn't. I did use the ipconf/all command on the laptop and the only thing I feel is worth mentioning is, it gave a line that said NetBOIOS over Tcpip is disabled, if that means anything. Thanks for any help you can offer. Perhaps Jack thought your new switch was wireless because you didn't mention that you had connected a patch cable between your old router and the new switch. You did that, of course? When you have the router connected to the switch and the switch connected to the laptop, what else does ipconfig /all report beside NetBIOS disabled? Specifically, what is shown for the laptop's IP address, subnet mask, and gateway IP address? Similarly, what result from ipconfig /all when you connect one of your working computers to the switch (and reboot)? How do those results compare to ipconfig /all run on a computer connected to the router and successfully accessing the Internet? And you should explicitly enable NetBIOS over TCP/IP on all of your computers. Right click on the LAN icon, select Properties; select TCP/IP and click Properties; click Advanced on the General tab; then click the WINS tab. See http://networking.nitecruzr.net/2006...ver-tcpip.html -- Lem -- MS-MVP To the moon and back with 2K words of RAM and 36K words of ROM. http://en.wikipedia.org/wiki/Apollo_Guidance_Computer http://history.nasa.gov/afj/compessay.htm |
#8
|
|||
|
|||
New Unmanaged Switch Doesn't Connect to Router
Hi Lori.
Your first Post states: "Got a new laptop and need to connect. Bought a TP-Link unmanaged five-port router". I.e. in your own words five-port-router. Wireless or not, my link explains how to connect second Router as a switch, or and Wireless Access Point. In any case the issue can be software, which was addressed by Lem, or hardware mismatch in case there is an Uplink issue between the Router's port and the new switch's port. http://www.ezlan.net/faq.html#crossover Jack (MS, MVP-Networking) "Lori" wrote in message ... Jack, Thanks for the fast reply, but you may have misread my post. I am on a HARD WIRED router for years and added a switch to connect my laptop to the network and provide Internet access. Please re-read it and see if that is what you meant to say. Nothing about this involved more than one router or anything wireless. I have connected the laptop to the switch via CAT 5e cable. Thanks! "Jack (MVP-Networking)." wrote: Hi There is No need for two Routers. If your New Router is Wireless use it instead of the old Router. If you do want to keep two Routers then the second Router has to be connected like this. Using a Wireless Router as a switch with an Access Point - http://www.ezlan.net/router_AP.html Jack (MS, MVP-Networking). "Lori" wrote in message news Hi, all. Thanks in advance for any help anyone can offer. Been running an Linksys BEFSR81 wired router, four port. Got a new laptop and need to connect. Bought a TP-Link unmanage five-port router. Connected it by the AC adapter and a new CAT 5e cable going from the laptop to the #1 port of the switch. Supposedly, you don't have to do anything. Well, ran the setup wizards for both the network and the Internet connection and although the icon at the bottom popped up and said I was connected, I cannot connect. The main computers are all running Windows XP Home, SP2, the laptop Windows XP Pro, SP3. I did try plugging an existing connected computer out from the router and plugging it into the switch but it didn't connect either. Then I took the plug that comes in from the cable outside and tried plugging into the switch but that didn't give Internet service either. I am stumped. It may be obvious to someone who knows switches, but I don't and it isn't. I did use the ipconf/all command on the laptop and the only thing I feel is worth mentioning is, it gave a line that said NetBOIOS over Tcpip is disabled, if that means anything. Thanks for any help you can offer. |
#9
|
|||
|
|||
New Unmanaged Switch Doesn't Connect to Router
Hi Lori.
Your first Post states: "Got a new laptop and need to connect. Bought a TP-Link unmanaged five-port router". I.e. in your own words five-port-router. Wireless or not, my link explains how to connect second Router as a switch, or and Wireless Access Point. In any case the issue can be software, which was addressed by Lem, or hardware mismatch in case there is an Uplink issue between the Router's port and the new switch's port. http://www.ezlan.net/faq.html#crossover Jack (MS, MVP-Networking) "Lori" wrote in message ... Jack, Thanks for the fast reply, but you may have misread my post. I am on a HARD WIRED router for years and added a switch to connect my laptop to the network and provide Internet access. Please re-read it and see if that is what you meant to say. Nothing about this involved more than one router or anything wireless. I have connected the laptop to the switch via CAT 5e cable. Thanks! "Jack (MVP-Networking)." wrote: Hi There is No need for two Routers. If your New Router is Wireless use it instead of the old Router. If you do want to keep two Routers then the second Router has to be connected like this. Using a Wireless Router as a switch with an Access Point - http://www.ezlan.net/router_AP.html Jack (MS, MVP-Networking). "Lori" wrote in message news Hi, all. Thanks in advance for any help anyone can offer. Been running an Linksys BEFSR81 wired router, four port. Got a new laptop and need to connect. Bought a TP-Link unmanage five-port router. Connected it by the AC adapter and a new CAT 5e cable going from the laptop to the #1 port of the switch. Supposedly, you don't have to do anything. Well, ran the setup wizards for both the network and the Internet connection and although the icon at the bottom popped up and said I was connected, I cannot connect. The main computers are all running Windows XP Home, SP2, the laptop Windows XP Pro, SP3. I did try plugging an existing connected computer out from the router and plugging it into the switch but it didn't connect either. Then I took the plug that comes in from the cable outside and tried plugging into the switch but that didn't give Internet service either. I am stumped. It may be obvious to someone who knows switches, but I don't and it isn't. I did use the ipconf/all command on the laptop and the only thing I feel is worth mentioning is, it gave a line that said NetBOIOS over Tcpip is disabled, if that means anything. Thanks for any help you can offer. |
#10
|
|||
|
|||
New Unmanaged Switch Doesn't Connect to Router
Thanks, guys. I knew it would end up being something simple. I didn't
realize that you need a patch cable! DOY! I have blonde roots sometimes...LOL. But I had figured it out by the time I read this. I did try to put one of the working computer's cables from the router into the switch and it didn't work, but five-port I thought meant five usable ports for computers! You have to use one of those to patch into the router, so it's actually really only four ports that are usable. All's well that ends well, I guess, and it is up and running now, after an entire afternoon wasted trying. I was under the impression (and I shouldn't do impressions) that since the instructions do no tell you that you need to do that, that the switch is able to pick up on the router wirelessly. My bad. Thanks again. "Jack (MS, MVP-Networking)" wrote: Hi Lori. Your first Post states: "Got a new laptop and need to connect. Bought a TP-Link unmanaged five-port router". I.e. in your own words five-port-router. Wireless or not, my link explains how to connect second Router as a switch, or and Wireless Access Point. In any case the issue can be software, which was addressed by Lem, or hardware mismatch in case there is an Uplink issue between the Router's port and the new switch's port. http://www.ezlan.net/faq.html#crossover Jack (MS, MVP-Networking) "Lori" wrote in message ... Jack, Thanks for the fast reply, but you may have misread my post. I am on a HARD WIRED router for years and added a switch to connect my laptop to the network and provide Internet access. Please re-read it and see if that is what you meant to say. Nothing about this involved more than one router or anything wireless. I have connected the laptop to the switch via CAT 5e cable. Thanks! "Jack (MVP-Networking)." wrote: Hi There is No need for two Routers. If your New Router is Wireless use it instead of the old Router. If you do want to keep two Routers then the second Router has to be connected like this. Using a Wireless Router as a switch with an Access Point - http://www.ezlan.net/router_AP.html Jack (MS, MVP-Networking). "Lori" wrote in message news Hi, all. Thanks in advance for any help anyone can offer. Been running an Linksys BEFSR81 wired router, four port. Got a new laptop and need to connect. Bought a TP-Link unmanage five-port router. Connected it by the AC adapter and a new CAT 5e cable going from the laptop to the #1 port of the switch. Supposedly, you don't have to do anything. Well, ran the setup wizards for both the network and the Internet connection and although the icon at the bottom popped up and said I was connected, I cannot connect. The main computers are all running Windows XP Home, SP2, the laptop Windows XP Pro, SP3. I did try plugging an existing connected computer out from the router and plugging it into the switch but it didn't connect either. Then I took the plug that comes in from the cable outside and tried plugging into the switch but that didn't give Internet service either. I am stumped. It may be obvious to someone who knows switches, but I don't and it isn't. I did use the ipconf/all command on the laptop and the only thing I feel is worth mentioning is, it gave a line that said NetBOIOS over Tcpip is disabled, if that means anything. Thanks for any help you can offer. |
#11
|
|||
|
|||
New Unmanaged Switch Doesn't Connect to Router
Thanks, guys. I knew it would end up being something simple. I didn't
realize that you need a patch cable! DOY! I have blonde roots sometimes...LOL. But I had figured it out by the time I read this. I did try to put one of the working computer's cables from the router into the switch and it didn't work, but five-port I thought meant five usable ports for computers! You have to use one of those to patch into the router, so it's actually really only four ports that are usable. All's well that ends well, I guess, and it is up and running now, after an entire afternoon wasted trying. I was under the impression (and I shouldn't do impressions) that since the instructions do no tell you that you need to do that, that the switch is able to pick up on the router wirelessly. My bad. Thanks again. "Jack (MS, MVP-Networking)" wrote: Hi Lori. Your first Post states: "Got a new laptop and need to connect. Bought a TP-Link unmanaged five-port router". I.e. in your own words five-port-router. Wireless or not, my link explains how to connect second Router as a switch, or and Wireless Access Point. In any case the issue can be software, which was addressed by Lem, or hardware mismatch in case there is an Uplink issue between the Router's port and the new switch's port. http://www.ezlan.net/faq.html#crossover Jack (MS, MVP-Networking) "Lori" wrote in message ... Jack, Thanks for the fast reply, but you may have misread my post. I am on a HARD WIRED router for years and added a switch to connect my laptop to the network and provide Internet access. Please re-read it and see if that is what you meant to say. Nothing about this involved more than one router or anything wireless. I have connected the laptop to the switch via CAT 5e cable. Thanks! "Jack (MVP-Networking)." wrote: Hi There is No need for two Routers. If your New Router is Wireless use it instead of the old Router. If you do want to keep two Routers then the second Router has to be connected like this. Using a Wireless Router as a switch with an Access Point - http://www.ezlan.net/router_AP.html Jack (MS, MVP-Networking). "Lori" wrote in message news Hi, all. Thanks in advance for any help anyone can offer. Been running an Linksys BEFSR81 wired router, four port. Got a new laptop and need to connect. Bought a TP-Link unmanage five-port router. Connected it by the AC adapter and a new CAT 5e cable going from the laptop to the #1 port of the switch. Supposedly, you don't have to do anything. Well, ran the setup wizards for both the network and the Internet connection and although the icon at the bottom popped up and said I was connected, I cannot connect. The main computers are all running Windows XP Home, SP2, the laptop Windows XP Pro, SP3. I did try plugging an existing connected computer out from the router and plugging it into the switch but it didn't connect either. Then I took the plug that comes in from the cable outside and tried plugging into the switch but that didn't give Internet service either. I am stumped. It may be obvious to someone who knows switches, but I don't and it isn't. I did use the ipconf/all command on the laptop and the only thing I feel is worth mentioning is, it gave a line that said NetBOIOS over Tcpip is disabled, if that means anything. Thanks for any help you can offer. |
Thread Tools | |
Display Modes | |
|
|