If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#16
|
|||
|
|||
Battery Change - Configuration Pointers
Strange you should mention the expiration date.
I purchased two double packs about 3 months ago (well known brand) an no expiration date was printed anywhere on the package or the batteries. Unless the date was 2032 ;-) "After wiping, handle the wafer battery only by its sides" Good point, something I do by habit (like DVD media) and forgot to mention. -- JS http://www.pagestart.com "VanguardLH" wrote in message ... JS wrote: I'll make a few suggestions. I would add some additional steps (shown inline): 1) Buy the correct battery. Check its expiration is 4 years from today. Get a double pack (in case one of them is defective). 1a) Shutdown the operating system. 1b) Power down the computer. 1c) Pull the power cord; otherwise, with ATX motherboards, a 5V standby line is still active from the power supply to the motherboard to power the power-up circuitry (to which goes the Power button on the front panel). 2) Look at the placement and ease of access to the existing battery on the motherboard. Use good lighting so everything is easily visable. 3) Make note of the polarity on the surface of the battery as you see it in the motherboard. 4) Walk thru the steps (before you actually perform them) of how you plan to remove the old battery and insert the new one. (I use a very small plastic "Non conductive" flat bladed screwdriver to help lift out the old battery). 5) Place the new battery on a none conductive surface within easy reach. 5a) When you pick up the new battery, wipe it clean of fingerprints. 5b) After wiping, handle the wafer battery only by its sides (or wear gloves). Do not touch the flat contact surfaces with your bare fingers. Body oil results in oxide on the surface that degrades the contact area. 6) If you can remove the old battery and insert the new one in about 20 seconds or less you may find all the BIOS setting have not changed any no action is required on your part. If all else fails then you can revert to the documentation you have posted and the others answers you receive to your post. |
Ads |
#17
|
|||
|
|||
Battery Change - Configuration Pointers
Strange you should mention the expiration date.
I purchased two double packs about 3 months ago (well known brand) an no expiration date was printed anywhere on the package or the batteries. Unless the date was 2032 ;-) "After wiping, handle the wafer battery only by its sides" Good point, something I do by habit (like DVD media) and forgot to mention. -- JS http://www.pagestart.com "VanguardLH" wrote in message ... JS wrote: I'll make a few suggestions. I would add some additional steps (shown inline): 1) Buy the correct battery. Check its expiration is 4 years from today. Get a double pack (in case one of them is defective). 1a) Shutdown the operating system. 1b) Power down the computer. 1c) Pull the power cord; otherwise, with ATX motherboards, a 5V standby line is still active from the power supply to the motherboard to power the power-up circuitry (to which goes the Power button on the front panel). 2) Look at the placement and ease of access to the existing battery on the motherboard. Use good lighting so everything is easily visable. 3) Make note of the polarity on the surface of the battery as you see it in the motherboard. 4) Walk thru the steps (before you actually perform them) of how you plan to remove the old battery and insert the new one. (I use a very small plastic "Non conductive" flat bladed screwdriver to help lift out the old battery). 5) Place the new battery on a none conductive surface within easy reach. 5a) When you pick up the new battery, wipe it clean of fingerprints. 5b) After wiping, handle the wafer battery only by its sides (or wear gloves). Do not touch the flat contact surfaces with your bare fingers. Body oil results in oxide on the surface that degrades the contact area. 6) If you can remove the old battery and insert the new one in about 20 seconds or less you may find all the BIOS setting have not changed any no action is required on your part. If all else fails then you can revert to the documentation you have posted and the others answers you receive to your post. |
|
Thread Tools | |
Display Modes | |
|
|